Axial stent strut angle influences wall shear stress after stent implantation: analysis using 3D computational fluid dynamics models of stent foreshortening

Introduction  

The success of vascular stents in the restoration of blood flow is limited by restenosis. Recent data generated from computational fluid dynamics (CFD) models suggest that the vascular geometry created by an implanted stent causes local alterations in wall shear stress (WSS) that are associated with neointimal hyperplasia (NH). Foreshortening is a potential limitation of stent design that may affect stent performance and the rate of restenosis. The angle created between axially aligned stent struts and the principal direction of blood flow varies with the degree to which the stent foreshortens after implantation.     

Computational mechanics of Nitinol stent grafts

A finite element analysis of tubular, diamond-shaped stent grafts under representative cyclic loading conditions for abdominal aortic aneurysm (AAA) repair is presented. Commercial software was employed to study the mechanical behavior and fatigue performance of different materials found in commercially available stent-graft systems. Specifically, the effects of crimping, deployment, and cyclic pressure loading on stent-graft fatigue life, radial force, and wall compliances were simulated and analyzed for two types of realistic but different Nitinol materials (NITI-1 and NITI-2) and grafts (expanded polytetrafluoroethylene-ePTFE and polyethylene therephthalate-PET). The results show that NITI-1 stent has a better crimping performance than NITI-2. Under representative cyclic pressure loading, both NITI-1 and NITI-2 sealing stents are located in the safe zone of the fatigue-life diagram; however, the fatigue resistance of an NITI-1 stent is better than that of an NITI-2 stent. It was found that the two types of sealing stents do not damage a healthy neck artery. In the aneurysm section, the NITI-1&ePTFE, NITI-1&PET, and NITI-2&PET combinations were free of fatigue fracture when subjected to conditions of radial stress between 50 and 150mmHg. In contrast, the safety factor for the NITI-2&ePFTE combination was only 0.67, which is not acceptable for proper AAA stent-graft design. In summary, a Nitinol stent with PET graft may greatly improve fatigue life, while its compliance is much lower than the NITI-ePTFE combination.     

Stent implantation through a self-expanding stent

Jailing of a side-branch is a known complication of stent implantation, and makes access to the side-branch difficult, especially if the stent is of the self-expanding type. Although plain balloon angioplasty is feasible for the jailed side-branches, the use of newer devices (a stent, Rotablation or atherectomy) has not been described. We describe a novel way of treating a side-branch jailed by a self-expanding stent by using stent implantation through the strut of a self-expanding stent.     

Influences of plaque eccentricity and composition on the stent–plaque–artery interaction during stent implantation

Biomechanics and Modeling in Mechanobiology - This work aims to investigate the effects of plaque eccentricity and composition on the stent performance and stress distributions of plaque and artery...     

Self-expanding stent modelling and radial force accuracy

Computational simulations using finite element analysis are a tool commonly used to analyse stent designs, deployment geometries and interactions between stent struts and arterial tissue. Such studies require large computational models and efforts are often made to simplify models in order to reduce computational time while maintaining reasonable accuracy. The objective of the study is focused on computational modelling and specifically aims to investigate how different methods of modelling stent–artery interactions can affect the results, computational time taken and computational size of the model. Various different models, each with increasing levels of complexity, are used to simulate this analysis, representing the many assumptions and simplifications used in other similar studies in order to determine what level of simplification will still allow for an accurate representation of stent radial force and resulting stress concentrations on the inner lining of the vessel during self-expanding stent deployment. The main conclusions of the study are that methods used in stent crimping impact on the resulting predicted radial force of the stent; that accurate representation of stent–artery interactions can only be made when modelling the full length of the stent due to the incorporation of end effects; and that modelling self-contact of the stent struts greatly impacts on the resulting stress concentrations within the stent, but that the effect of this on the unloading behaviour and resulting radial force of the stent is negligible.     

可降解冠状动脉支架的研究进展

冠脉内支架植入是临床上预防PTCA术后再狭窄并发症的有效措施,但金属支架仅在植入早期发生作用,在冠脉内壁修复完成后则成为多余的负担,可能激活血小板及多种凝血因子聚集导致血栓形成及刺激血管壁造成心脏事件及再狭窄的发生。针对上述问题,生物可降解冠状动脉支架的研究得到了相当的发展。本文就可降解支架的发展及现状作一简要综述。     

Structural analysis of two different stent configurations

Two different stent configurations (i.e. the well known Palmaz–Schatz (PS) and a new stent configuration) are mechanically investigated. A finite element model was used to study the two geometries under combining loads and a computational fluid dynamic model based on fluid structure interaction was developed investigating the plaque and the artery wall reactions in a stented arterial segment. These models determine the stress and displacement fields of the two stents under internal pressure conditions. Results suggested that stent designs cause alterations in vascular anatomy that adversely affect arterial stress distributions within the wall, which have impact in the vessel responses such as the restenosis. The hemodynamic analysis shows the use of new stent geometry suggests better biofluid mechanical response such as the deformation and the progressive amount of plaque growth.     

Our capricious vessels: The influence of stent design and vessel geometry on the mechanics of intracranial aneurysm stent deployment

There is a growing interest in virtual tools to assist clinicians in evaluating different procedures and devices for endovascular treatment. In the present study we use finite element analysis to investigate the influence of stent design and vessel geometry for stent assisted coiling of intracranial aneurysms. Nine virtual stenting procedures were performed: three nitinol stent designs ((i) an open cell stent resembling the Neuroform, (ii) a generic stiff and (iii) a more flexible closed cell design), were deployed in three patient-specific cerebral aneurysmatic vessels. We investigated the percentage of strut area covering the aneurysm neck, the straightening induced on the cerebrovasculature by the stent placement (quantified by the reduction in tortuosity), and stent apposition to the wall (quantified as the percentage of struts within 0.2mm of the vessel). The results suggest that the open cell design better covers the aneurysm neck (11.0±1.1%) compared to both the stiff (7.8±1.6%) and flexible (8.7±1.6%) closed cell stents, and induces less straightening of the vessel (-5.1±1.6% vs. -42.9±9.8% and -26.9±11.9% ). The open cell design has, however, less struts apposing well to the vessel wall (56.0±6.4%) compared to the flexible (73.4±4.6%) and stiff (70.4±5.1%) closed cell design. With the presented study, we hope to contribute to and improve aneurysm treatment, using a novel patient specific environment as a possible pre-operative tool to evaluate mechanical stent behavior in different vascular geometries.     

Local methylprednisolone delivery using a BiodivYsio phosphorylcholine-coated drug-delivery stent reduces inflammation and neointimal hyperplasia in a porcine coronary stent model

Phosphorylcholine (PC)-coated stents have shown excellent blood and tissue biocompatibility in porcine coronary arteries. The purpose of this study was to determine the efficacy of local methylprednisolone (MP) delivery using PC-coated stents to inhibit inflammatory response and in-stent neointimal hyperplasia in an overstretched porcine coronary model. BiodivYsio (Biocompatibles, Farnham, Surrey, UK) PC-coated drug delivery (DD) stents and DD stents loaded with a high dose of MP (269 microg) were implanted in the coronary arteries of 20 pigs with a balloon/artery ratio of 1.2 : 1. At five days the peri-strut inflammatory response score and thrombus score of the MP-loaded DD stents were lower than in the control stents. The neointimal hyperplasia of MP-loaded DD stents was significantly reduced (0.80 +/- 0.10 versus 0.48 +/- 0.10 mm(2), p < 0.01). At four-week follow-up, the inflammatory response of MP-loaded stents was lower than the control stents, but without significant difference. The MP-loaded stents showed decreased peri-strut arterial injury and in-stent neointimal hyperplasia (2.42 +/- 0.87 versus 1.62 +/- 0.71 mm(2), p < 0.05). It is concluded that local vascular delivery of a high dose of MP from PC-coated DD stents could effectively decrease inflammatory response and thrombus formation after oversized stent deployment and result in a significant reduction of neointimal hyperplasia.     

A new stent with streamlined cross-section can suppress monocyte cell adhesion in the flow disturbance zones of the endovascular stent

We proposed a new stent with streamlined cross-sectional wires, which is different from the clinical coronary stents with square or round cross-sections. We believe the new stent might have better hemodynamic performance than the clinical metal stents. To test the hypothesis, we designed an experimental study to compare the performance of the new stent with the clinical stents in terms of monocyte (U-937 cells) adhesion. The results showed that when compared with the clinical stents, the adhesion of U-937 cells were much less in the new stent. The results also showed that, when Reynolds number increased from 180 (the rest condition for the coronary arteries) to 360 (the strenuous exercise condition for the coronary arteries), the flow disturbance zones in the clinical stents became larger, while they became smaller with the new stent. The present experimental study therefore suggests that the optimization of the cross-sectional shape of stent wires ought to be taken into consideration in the design of endovascular stents.     

Late stent thrombosis, endothelialisation and drug-eluting stents

Drug-eluting stents (DES) significantly reduce the risk of restenosis after percutaneous coronary revascularisation, but an increased risk of late stent thrombosis (LST) has been put forward as a major safety concern. Meta-analysis of clinical trials, however, does not support this caveat. Even so, many interventional cardiologists think that LST is associated with DES and related to delayed endothelialisation. This hypothesis is based on autopsy studies and clinical intracoronary angioscopy. In autopsy studies, differences between endothelialisation of DES and baremetal stents (BMS) have been reported. Most preclinical studies, however, have failed to show any significant differences in endothelialisation between DES and BMS. Our own studies, using the porcine coronary artery model, also suggest that DES show no differences in re-endothelialisation. However, DES do delay vascular healing and induce endothelial dysfunction. This paper will review clinical and animal studies which consider re-endothelialisation and LST. (Neth Heart J 2009;17:177–81.)     

Comparison of element technologies for modeling stent expansion

Numerical analysis has become a standard, and in fact required, component of the process in which new biomedical stent devices are designed and approved. Despite this, very little work has been performed comparing the efficiency of various numerical techniques currently available to the analyst. The present paper begins this study by comparing the computational efficiency and results achieved using various element technologies in the context of stent deployment simulations. The findings indicate that the methodologies most commonly adopted in the present literature/industrial practice are in many cases less than optimal with regard to computational efficiency.     

A method for external auditory canal stent fabrication

An external auditory canal stent made of Dow Corning elastomer and a silicone catheter has proved useful in maintaining the patency of a newly reconstructed external canal. This paper describes the method of stent construction and presents a case report illustrating its use.