Fabrication of sucrose biosensor based on single mode planar optical waveguide using co-immobilized plant invertase and GOD

In present studies, the new optical sensing platform based on optical planar waveguide (OPWG) for sucrose estimation was reported. An evanescent-wave biosensor was designed by using novel agarose–guar gum (AG) biopolymer composite sol–gel with entrapped enzymes (acid invertase (INV) and glucose oxidase (GOD)). Partially purified watermelon invertase isolated from Citrullus vulgaris fruit (specific activity 832 units mg⁻¹) in combination with GOD was physically entrapped in AG sol–gel and cladded on the surface of optical planar waveguide. Na⁺–K⁺ ion-exchanged glass optical waveguides were prepared and employed for the fabrication of sucrose biosensor. By addressing the enzyme modified waveguide structure with, the optogeometric properties of adsorbed enzyme layer (12 μm) at the sensor solid–liquid interface were studied. The OPWG sensor with short response time (110 s) was characterized using the 0.2 M acetate buffer, pH 5.5. The fabricated sucrose sensor showed concentration dependent linear response in the range 1 × 10⁻¹⁰ to 1 × 10⁻⁶ M of sucrose. Lower limit of detection of this novel AG–INV–GOD cladded OPWG sensor was found to be 2.5 × 10⁻¹¹ M sucrose, which indicates that the developed biosensor has higher sensitivity towards sucrose as compared to earlier reported sensors using various transducer systems. Biochips when stored at room temperature, showed high stability for 81 days with 80% retention of original sensitivity. These sucrose sensing biochips showed good operational efficiency for 10 cycles. The proper confinement of acid invertase and glucose oxidase in hydrogel composite was confirmed by scanning electron microscopy (SEM) images. The constructed OPWG sensor is versatile, easy to fabricate and can be used for sucrose measurements with very high sensitivity.     

Graft copolymerization of acrylic acid onto guar gum initiated by vanadium (V)–mercaptosuccinic acid redox pair

Guar gum has been modified by graft copolymerization with acrylic acid in aqueous medium using vanadium (V)–mercaptosuccinic acid redox system. The optimum reaction conditions affording maximum grafting ratio, efficiency, add on and conversion have been determined. The grafting parameters have been found to increase with increase in vanadium (V) concentration upto 1.0 × 10⁻² mol dm⁻³, but these parameters decrease on further increasing the vanadium (V) concentration. On increasing the mercaptosuccinic acid concentration from 1.0 × 10⁻² to 4.0 × 10⁻² mol dm⁻³ grafting ratio, efficiency and add on increase up to 2.0 × 10⁻² mol dm⁻³ but decrease with further increase in mercaptosuccinic acid concentration. On varying the acrylic acid concentration from 5.0 × 10⁻² to 30.0 × 10⁻² mol dm⁻³, maximum grafting ratio, efficiency and add on have been obtained at 20.0 × 10⁻² mol dm⁻³. The grafting ratio, add on and conversion increase, on increasing the H⁺ ion concentration from 1.5 × 10⁻¹ to 6.0 × 10⁻¹ mol dm⁻³. On increasing the guar gum concentration the grafting parameters increase. The grafting ratio, add on and conversion have been found to increase with time period while efficiency started decreasing after 120 min. It has been observed that %G increases on increasing the temperature up to 35 °C. The graft copolymer has been characterized by IR spectroscopy and thermogravimetric analysis.     

Synthesis of graft copolymer (k-carrageenan-g-N,N-dimethylacrylamide) and studies of metal ion uptake, swelling capacity and flocculation properties

Graft copolymer of k-carrageenan and N,N-dimethylacrylamide has been synthesized by free radical polymerization using peroxymonosulphate/glycolic acid redox pair in an inert atmosphere. The grafting parameters i.e. grafting ratio, add on and efficiency decrease with increase in concentration of k-carrageenan from 0.6 to 1.4 g dm⁻³ and hydrogen ion from 3 × 10⁻³ to 7 × 10⁻³ mol dm⁻³, but these grafting parameters increase with increase in concentration of N,N-dimethylacrylamide from 16 × 10⁻² to 32 × 10⁻² mol dm⁻³, and peroxymonosulphate from 0.8 × 10⁻² to 2.4 × 10⁻² mol dm⁻³. The metal ion sorption, swelling behaviour and flocculation properties have been studied. The intrinsic viscosity of pure and grafted samples has been measured by using Ubbelohde capillary viscometer. Flocculation capability of k-carrageenan and k-carrageenan-g-N,N-dimethylacrylamide for both coking and non-coking coals has been studied for the treatment of coal mine waste water. The graft copolymer has been characterized by Infrared (IR) spectroscopy and thermogravimetric analysis.     

Binding of genistein to human serum albumin demonstrated using tryptophan fluorescence quenching

Genistein is an isoflavone and phytoestrogen that is a potent inhibitor of cell proliferation and angiogenesis. This study was designed to investigate the binding of genistein to human serum albumin (HSA) under physiological conditions with drug concentrations in the range of 6.7 × 10⁻⁶ to 2.0 × 10⁻⁵ mol L⁻¹ and HSA concentration at 1.5 × 10⁻⁶ mol L⁻¹. Fluorescence quenching methods in combination with Fourier transform infrared (FT-IR) spectroscopy and circular dichroism (CD) spectroscopy was used to determine the binding mode, the binding constant and the protein structure changes in the presence of genistein in aqueous solution. Changes in the CD spectra and FT-IR spectra were observed upon ligand binding, and the degree of tryptophan fluorescence quenching change did significantly in the complexes. These data have proved the change in protein secondary structure accompanying ligand binding. The change in tryptophan fluorescence intensity was used to determine the binding constants. The thermodynamic parameters, the enthalpy change (ΔH) and the entropy change (ΔS) were calculated to be −22.24 kJ mol⁻¹and 19.60 J mol⁻¹ K⁻¹ according to the van’t Hoff equation, which indicated that hydrophobic and electrostatic interactions play the main role in the binding of genistein to HSA.     

SEC of mono-carboxymethyl cellulose (CMC) in a wide range of pH; Mark–Houwink constants

A method for determination of carboxymethyl cellulose (CMC) molecular weight (M_W) and chemical heterogeneity (degree of oxidation (DO)) using a bi-detector HPSEC (UV-detector online with refractometer) has been developed. It has been found that the use of 0.5 N NaOH or 0.4 M acetate buffer as the eluent ensures CMC separation according to M_W. It has been revealed that the universal calibration for the polyelectrolyte CMC and the neutral polymer dextran is valid under the conditions applied. The Mark–Houwink equations for CMC in 0.5 N NaOH and 0.4 M acetate buffer have been estimated to be [η]=5.37×10⁻⁴ M_W^0.73 and [η] =2.24×10⁻⁴ M_W^0.83 dl g⁻¹, respectively. The equation log K=1.64−4.00 ml g⁻¹ for CMC has been estimated. An approach for determining DO from adsorption at 290 or 313 nm has been developed.     

A method for the design of 3D scaffolds for high-density cell attachment and determination of optimum perfusion culture conditions

The application of in vitro cultured cells in tissue engineering or drug screening, aimed at complex soft tissues such as liver, requires in vivo physiological function of the cultured cells. For this purpose, the scaffold in which cells are cultured should provide a microenvironment similar to an in vivo one with a three-dimensional extracellular matrix, a high supply capacity of O₂ and nutrients, and high cell density. In this paper, we propose a method to design (1) the geometry of the scaffold, with a surface/volume ratio optimized to allow high-density (5×10⁷ cells/mL) cell culture and (2) culture conditions that will supply optimal quantities of oxygen and nutrients. CFD modeling of mass transport was used to determine the shear stress as well as O₂ and glucose metabolism in the scaffold (20 mm width–35 mm length) for various flow rates. Validation of the model was done through comparison with flow resistance and micro-PIV experiments. CFD analysis showed the maximum metabolic rate densities for this scaffold are 6.04×10⁻³ mol/s/m³ for O₂ at 0.71 mL/min and 1.91×10⁻² mol/s/m³ for glucose at 0.35 mL/min.     

Epinephrine quantification in pharmaceutical formulations utilizing plant tissue biosensors

A plant tissue biosensor associated with flow injection analysis is proposed to determine epinephrine in pharmaceutical samples. The polyphenol oxidase enzymes present in the fibers of a palm tree fruits (Livistona chinensis), catalyses the oxidation of epinephrine to epinephrinequinone as a primary product. This product is then electrochemically reduced (at −0.10 V versus Ag/AgCl_sat) on the biosensor surface and the resulting current is used for the quantification of epinephrine. The biosensor provides a linear response for epinephrine in the concentration range from 5.0 × 10⁻⁵ to 3.5 × 10⁻⁴ mol l⁻¹. The limit of detection estimated for this interval was 1.5 × 10⁻⁵ mol l⁻¹ and the correlation coefficient of 0.998, working under a flow rate of 2.0 ml min⁻¹ and using a sample loop of 100 μl. The repeatability (R.S.D. for 10 consecutive determinations of a 3.0 × 10⁻⁴ mol l⁻¹ epinephrine solution) was 3.1%. The results obtained by the method here proposed were compared with the official UV spectrophotometric procedure and also using a plant tissue reactor. The responses obtained with the proposed strategies were in good agreement with both ways of analyses, whereas the values obtained by the official spectrophotometric method was strongly affected by benzoic acid, present in the formulation of pharmaceutical product utilized for inhalation. Such favorable results obtained with the carbon paste biosensor or utilizing the bioreactor, joined with the simplicity of its preparation turns these procedures very attractive for epinephrine quantification in pharmaceutical products.     

Optimizing the formulation of a myoglobin molecularly imprinted thin-film polymer--formed using a micro-contact imprinting method

Thin-film myoglobin molecularly imprinted polymers have been fabricated using a micro-contact approach. By initially selecting the cross-linker on the basis of it having a minimal recognition for the template and using this as a starting point for functional monomer selection, we have produced myoglobin imprinted polymers with exceptionally high selectivities.

The affinity of the polymers, for myoglobin, when prepared with a variety of different cross-linkers and no functional monomer was evaluated. Of these, tetraethylene glycol dimethacrylate (TEGDMA) exhibited the lowest affinity for the template species. Methyl methacrylate (MMA) was chosen as the functional monomer as when it was used in conjunction with TEGDMA, it exhibited maximum selectivity for the template compared to polymers made with other functional monomers.

With a MMA to TEGDMA ratio of 1 to 3, the myoglobin molecularly imprinted polymer adsorbed 15.03 ± 0.89 × 10⁻¹¹ mole/cm² of template from a 5.68 × 10⁻⁷ M myoglobin solution, compared to 2.58 ± 0.02 × 10⁻¹¹ mole/cm² for a polymer of similar composition, but formed in the absence of a template. Various washing conditions, using alkaline media to remove the template, were investigated. An extraction solvent comprising 2 wt.% SDS and 0.6 wt.% NaOH used at 80 °C for 30 min was shown to give the highest imprinting factor i.e. 5.83 with 72.82% myoglobin removal.

The saturation kinetics of template binding to the thin-film MIP were examined and found to display a simple two-phase profile typical of non-cooperative binding. A Scatchard binding plot showed the dissociation constant (K_d) for the specific binding phase to be 3.4 × 10⁻⁷ M and the binding site capacity to be 7.24 × 10⁻¹¹ mole/cm². For the non-specific binding phase, K_d was found to be 1.355 × 10⁻⁵ M and the binding site capacity was determined as 9.62 × 10⁻¹⁰ mole/cm².

Selectivity experiments were carried out in both single protein and binary protein systems all using a total protein concentration of 5.68 × 10⁻⁷ M. The molar ratio of adsorbed myoglobin to IgG, HSA and hemoglobin was found to 115.5, 230.9 and 2.5, respectively. While, in binary competition systems, myoglobin selectivity to IgG, HSA and hemoglobin was, respectively, 94.18, 98.21 and 61.09%. Rebinding in natural biological matrices, i.e. human serum or urine, showed the imprinted films to have significantly greater uptake than non-imprinted films. Re-binding in undiluted urine was found to be a facile process, with the imprinting factor, i.e. the ratio of MIP to NIP binding, being determined as 37.4.     

Glucose biosensor based on immobilization of glucose oxidase in poly(o-aminophenol) film on polypyrrole-Pt nanocomposite modified glassy carbon electrode

Novel Pt nanoclusters embedded polypyrrole nanowires (PPy-Pt) composite was electrosynthesized on a glassy carbon electrode, denoted as PPy-Pt/GCE. A glucose biosensor was further fabricated based on immobilization of glucose oxidase (GOD) in an electropolymerized non-conducting poly(o-aminophenol) (POAP) film that was deposited on the PPy-Pt/GCE. The morphologies of the PPy nanowires and PPy-Pt nanocomposite were characterized by field emission scanning electron microscope (FE-SEM). Effect of experimental conditions involving the cycle numbers for POAP deposition and Pt nanoclusters deposition, applied potential used in glucose determination, temperature and pH value of the detection solution were investigated for optimization. The biosensor exhibited an excellent current response to glucose over a wide linear range from 1.5 × 10⁻⁶ to 1.3 × 10⁻² M (r = 0.9982) with a detection limit of 4.5 × 10⁻⁷ M (s/n = 3). Based on the combination of permselectivity of the POAP and the PPy films, the sensor had good anti-interference ability to ascorbic acid (AA), uric acid (UA) and acetaminophen. The apparent Michaelis–Menten constant (K_m) and the maximum current density (I_m) were estimated to be 23.9 mM and 378 μA/cm², respectively. In addition, the biosensor had also good sensitivity, stability and reproducibility.     

Estradiol inhibits the estrone sulfatase activity in normal and cancerous human breast tissues

It is well accepted that estradiol (E₂) plays an important role in the genesis and evolution of breast cancer. Quantitative evaluation indicates that in human breast tumor, estrone sulfate (E₁S) ‘via sulfatase’ is a much more likely precursor for E₂ than is androstenedione ‘via aromatase’. In previous studies, it was demonstrated that in isolated MCF-7 and T-47D breast cancer cell lines, estradiol can block estrone sulfatase activity. In the present study, the effect of E₂ was explored using total normal and cancerous breast tissues. This study was carried out with post-menopausal patients with breast cancer. None of the patients had a history of endocrine, metabolic or hepatic diseases or had received treatment in the previous 2 months. Each patient received local anaesthetic (lidocaine 1%) and two regions of the mammary tissue were selected: (A) the tumoral tissue and (B) the distant zone (glandular tissue) which was considered as normal. Samples were placed in liquid nitrogen and stored at –80 °C until enzyme activity analysis. Breast cancer histotypes were ductal and post-menopausal stages were T2. Homogenates of tumoral or normal breast tissues (45–75 mg) were incubated in 20 mM Tris–HCl, pH 7.2 with physiological concentrations of [³H]-E₁S (5 × 10⁻⁹ M) alone or in the presence of E₂ (5 × 10⁻⁵ to 5 × 10⁻⁷ M) during 30 min or 3 h. E₁S, E₁ and E₂ were characterized by thin layer chromatography and quantified using the corresponding standard. The sulfatase activity is significantly more intense with the breast cancer tissue than normal tissue, since the concentration of E₁ was 3.20 ± 0.15 and 0.42 ± 0.07 pmol/mg protein, respectively after 30 min incubation. The values were 27.8 ± 1.8 and 3.5 ± 0.21 pmol/mg protein, respectively after 3 h incubation. Estradiol at the concentration of 5 × 10⁻⁷ M inhibits this conversion by 33% and 31% in cancerous and normal breast tissues, respectively and by 53% and 88% at the concentration of 5 × 10⁻⁵ M after 30 min incubation. The values were 24% and 18% for 5 × 10⁻⁷ M and 49% and 42% for 5 × 10⁻⁵ M, respectively after 3 h incubation. It was observed that [³H]-E₁S is only converted to [³H]-E₁ and not to [³H]-E₂ in normal or cancerous breast tissues, which suggests a low or no 17β-hydroxysteroid dehydrogenase (17β-HSD) Type 1 reductive activity in these experimental conditions. In conclusion, estradiol is a strong anti-sulfatase agent in cancerous and normal breast tissues. This data can open attractive perspectives in clinical trials using this hormone.     

A performance comparison of choline biosensors: anodic or cathodic detections of H2O2 generated by enzyme immobilized on a conducting polymer

Amperometric choline biosensors were fabricated by the covalent immobilization of an enzyme of choline oxidase (ChO) and a bi-enzyme of ChO/horseradish peroxidase (ChO/HRP) onto poly-5,2′:5′,2″-terthiophene-3′-carboxylic acid (poly-TTCA) modified electrodes (CPMEs). A sensor modified with ChO utilized the oxidation process of enzymatically generated H₂O₂ in a choline solution at +0.6 V. The other one modified with ChO/HRP utilized the reduction process of H₂O₂ in a choline solution at −0.2 V. Experimental parameters affecting the sensitivity of sensors, such as pH, applied potential, and temperature were optimized. A performance comparison of two sensors showed that one based on ChO/HRP/CPME had a linear range from 1.0×10⁻⁶ to 8.0×10⁻⁵ M and the other based on ChO/CPME from 1.0×10⁻⁶ to 5.0×10⁻⁵ M. The detection limits for choline employing ChO/HRP/CPME and ChO/CPME were determined to be about 1.0×10⁻⁷ and 4.0×10⁻⁷ M, respectively. The response time of sensors was less than 5 s. Sensors showed good selectivity to interfering species. The long-term storage stability of the sensor based on ChO/HRP/CPME was longer than that based on ChO/CPME.     

Direct electrochemistry of cytochrome c at ordered macroporous active carbon electrode

Three-dimensionally (3D) ordered macroporous active carbon has been fabricated and used as electrode substrate for the direct electrochemistry of horse heart cytochrome c (Cyt c). The Cyt c immobilized on the surface of the ordered macroporous active carbon shows a pair of well-defined and nearly reversible redox waves at the formal potential of −0.033 V in pH 6.8 phosphate buffer solution. The interaction between Cyt c and the 3D macroporous active carbon makes the formal potential shift negatively compared to that of Cyt c in solution. Spectrophotometric and electrochemical methods have been used to investigate the interaction between Cyt c and the porous active carbon. The immobilized Cyt c maintains its biological activity, and shows a surface controlled electrode process with the electron-transfer rate constant (k_s) of 17.6 s⁻¹ and the charge-transfer coefficient (a) of 0.52, and displays the features of a peroxidase in the electrocatalytic reduction of hydrogen peroxide (H₂O₂). A potential application of the Cyt c-immobilized porous carbon electrode as a biosensor to monitor H₂O₂ has been investigated. The steady-state current response increases linearly with H₂O₂ concentration from 2.0 × 10⁻⁵ to 2.4 × 10⁻⁴ mol l⁻¹. The detection limit (3σ) for determination of H₂O₂ has been found to be 1.46 × 10⁻⁵ mol l⁻¹.     

Specific interactions of steroids, arylhydrocarbons and flavonoids with progesterone receptors from the cytosol of the fungus Rhizopus nigricans

Rhizopus nigricans (R. nigricans) transforms fungitoxic progesterone into the less toxic 11-hydroxyprogesterone which is then able to exit the mycelia into the surrounding water. Hydroxylation of progesterone is an inducible process in which cytosolic progesterone receptors could be involved. In the present study, we characterised receptors with respect to ligand specificity and to their involvement in progesterone induction of hydroxylase. EC₅₀ values of different ligands (steroids, xenobiotic arylhydrocarbons and natural flavonoids) were determined by competition studies using 40 nM (³H)progesterone. C21 and C19 3-oxo-4-ene steroids were good competitors (EC₅₀ of progesterone 2.3 ± 0.1 × 10⁻⁷ M, EC₅₀ of androsten-3,17-dione 24 ± 2 × 10⁻⁷ M). The presence of hydroxyl groups in steroids significantly decreased the affinity for receptors. The arylhydrocarbons -naphthoflavone and ketoconazole exhibited EC₅₀ values of 0.3 ± 0.01 × 10⁻⁷ M and 27 ± 5 × 10⁻⁷ M, respectively, whereas β-naphthoflavone and benzo(a)pyrene were not able to displace labelled progesterone completely. The competition curves obtained by natural flavonoids also did not reach the bottom level of non-labelled progesterone, indicating the interaction at some allosteric binding site(s) of progesterone receptors. All ligands were examined for their involvement in progesterone-hydroxylase induction. Steroid agonists induced the enzyme in a dose-dependent manner in accordance with their affinity for receptors, whereas arylhydrocarbons and natural flavonoids did not induce the enzyme. The agonistic action of steroids, together with the antagonistic action of -naphthoflavone, strongly suggests the involvement of progesterone receptors in progesterone signalling resulting in the induction of progesterone-hydroxylase.     

Effects of interactions with micellar interfaces on the activity and structure of different lipolytic isoenzymes from Candida rugosa

The conformational and functional changes of cholesterol esterase (CE) and isolipase (CRL) from Candida rugosa after exposure to a micellar interface and subsequent extraction to a fresh buffer were studied. These two enzymes were activated by interaction with the micellar interface of a sulphosuccinic acid bis[2-ethylhexyl] ester/n-heptane/water system. For the hydrolysis of p-nitrophenyl butyrate ester in water, the catalytic efficiencies of CE and CRL were both improved because on activation their k_cat values increased from 378 to 465 and from 250 to 680 s⁻¹, respectively, while their K_m values decreased from 5.08 × 10⁻⁵ to 3.23 × 10⁻⁵ and from 2.28 × 10⁻⁴ to 1.14 × 10⁻⁴ M, respectively. After exposure to the micelles, CE showed a marked increase in its -helical content from 28 to 49%, but only limited changes were detected when CRL was exposed. These proteins exhibit similar capacities for increasing their -helical content in a helicogenic medium. In acetonitrile/water mixtures, CRL exhibits a partial decrease in the extent of its secondary structure, while CE exhibits an increase in its -helical content. The fact that this medium of reduced polarity permits one to simulate the effect of the AOT reverse micelles on the conformation of CE (increased helicity) but not their effect on the structure of CRL (decreased helicity) supports the hypothesis that only CE interacts to a significant extent with the apolar side of the micellar interface. After exposure to micelles of octyl-β-glucopyranoside, CE (but not CRL) showed a 10% increase in its -helical content.     

Glutathione-proline activation of feeding behavior in the zoanthid Palythoa psammophilia Walsh & Bowers

Palythoa psammophilia Walsh & Bowers has a well coordinated, stereotyped feeding response, the culminating step of which is ingestion; this may be elicited by the synergistic effect of the tripeptide glutathione and the -imino acid, proline. Either activator acting separately causes responses only at high concentrations (above 10⁻⁵ M for glutathione; above 10⁻⁴ M for proline) in a reduced number of animals and at a low rate (5.00 ± 1.73 min in 5 × 10⁻³ M solutions of glutathione; 11.10±3.74 min in 5 × 10⁻³ M solutions of proline). Highest percentages of response were obtained in combinations where glutathione was at a concentration of 5 × 10⁻³ M and proline at 5 × 10⁻⁴ M or in combinations of glutathione at concentrations 5 × 10⁻⁶ M and proline at 5 × 10⁻⁵ M. The speed of ingestion is considerably enhanced when these activators are combined (1.17±1.18 min).     

Comparison of the characterization on binding of alpinetin and cardamonin to lysozyme by spectroscopic methods

Studies on the binding affinity of protein to the active components of herbs are novel in biochemistry and are valuable for the information about speciation of drugs and exchange in biological systems. Alpinetin and cardamonin, two of the main constituents from the seeds of Alpinia katsumadai Hayata, have been used in traditional herbs as antibacterial, anti-inflammatory, and other important therapeutic activities of significant potency and low systemic toxicity. The interactions between two flavonoids analogs and lysozyme have been studied for the first time by spectroscopic method including Fourier transform infrared (FT-IR) spectroscopy, circular dichroism (CD) and UV-absorption spectroscopy in combination with Fluorescence quenching study. Both molecules showed high affinities to lysozyme under the experimental condition with drug concentrations from 3.33 × 10⁻⁶ to 2.67 × 10⁻⁵ mol L⁻¹ for alpinetin and 1.67 × 10⁻⁶ to 13.33 × 10⁻⁶ mol L⁻¹ for cardamonin. The alterations of protein secondary structure in the presence of drugs in aqueous solution were quantitatively estimated by the evidences from CD and FT-IR spectroscopy. The thermodynamic parameters obtained and the results of spectroscopic measurements suggest that hydrophobic and electrostatic interactions are the predominant intermolecular forces stabilizing two coordination compounds. The quenching mechanism and the number of binding site (n ≈ 1) were obtained by fluorescence titration data. The efficiency of energy transfer provided the binding distances of 4.04 and 5.90 nm for alpinetin-LYSO and cardamonin-LYSO systems, respectively.     

Kinetics and mechanism of the stoichiometric oxygenation of [Cu(fla)(idpa)]ClO4 [fla=flavonolate, IDPA=3,3′-imino-bis(N,N-dimethylpropylamine)] and the [Cu(fla)(idpa)]ClO4-catalysed oxygenation of flavonol

Oxygenation of [Cu^II(fla)(idpa)]ClO₄ (fla=flavonolate; IDPA=3,3′-iminobis(N,N-dimethylpropylamine)) in dimethylformamide gives [Cu^II(idpa)(O-bs)]ClO₄ (O-bs=O-benzoylsalicylate) and CO. The oxygenolysis of [Cu^II(fla)(idpa)]ClO₄ in DMF was followed by electronic spectroscopy and the rate law −d[{Cu^II(fla)(idpa)}ClO₄]/dt=k_obs[{Cu^II(fla)(idpa)}ClO₄][O₂] was obtained. The rate constant, activation enthalpy and entropy at 373 K are k_obs=6.13±0.16×10⁻³ M⁻¹ s⁻¹, ΔH^‡=64±5 kJ mol⁻¹, ΔS^‡=−120±13 J mol⁻¹ K⁻¹, respectively. The reaction fits a Hammett linear free energy relationship and a higher electron density on copper gives faster oxygenation rates. The complex [Cu^II(fla)(idpa)]ClO₄ has also been found to be a selective catalyst for the oxygenation of flavonol to the corresponding O-benzoylsalicylic acid and CO. The kinetics of the oxygenolysis in DMF was followed by electronic spectroscopy and the following rate law was obtained: −d[flaH]/dt=k_obs[{Cu^II(fla)(idpa)}ClO₄][O₂]. The rate constant, activation enthalpy and entropy at 403 K are k_obs=4.22±0.15×10⁻² M⁻¹ s⁻¹, ΔH^‡=71±6 kJ mol⁻¹, ΔS^‡=−97±15 J mol⁻¹ K⁻¹, respectively.     

Synthesis and inhibitory activity of optically active 2-benzyl-3-mercaptopropanoic acid against carboxypeptidase A

Both enantiomers of 2-benzyl-3-mercaptopropanoic acid were synthesized starting with racemic 3-acetylthio-2-benzylpropanoic acid methyl ester using a kinetic resolution with -chymotrypsin as a key step, and their inhibitory activities against carboxypeptidase A were determined to show that the S-isomer is much more potent (K_i = 7.8 × 10⁻⁹ M) than the racemic acid (K_i = 1.1 × 10⁻⁸ M).     

Entrapment of lipase into K-carrageenan beads and its use in hydrolysis of olive oil in biphasic system

The porcine pancrease lipase was immobilized by entrapment in the beads of K-carrageenan and cured by treatment with polyethyleneimine (PEI) in the phosphate buffer. The retention of hydrolytic activity of lipase and compressive strength of the beads were examined. The activity of free and immobilized lipase was assessed by using olive oil as the substrate. The immobilized enzyme exhibited a little shift towards acidic pH for its optimal activity and retained 50% of its activity after 5 cycles. When the enzyme concentration was kept constant and substrate concentration was varied the K_m and V_max were observed to be 0.18 × 10⁻² and 0.10, and 0.10 × 10⁻² and 0.09 respectively, for free and for entrapped enzymes. When the substrate concentration was kept constant and enzyme concentration was varied, the values of K_m and V_max were observed to be 0.19 × 10⁻⁷ and 0.41, and 0.18 × 10⁻⁷ and 0.41 for free and entrapped enzymes. Though this indicates that there is no conformational change during immobilization, it also shows that the reaction velocity depends on the concentration. Immobilized enzyme showed improved thermal and storage stability. Hydrolysis of olive oil in organic–aqueous two-phase system using fixed bed reactor was carried out and conditions were optimized. The enzyme in reactor retained 30% of its initial activity after 480 min (12 cycles).     

A cationic chalcogenoxanthylium photosensitizer effective in vitro in chemosensitive and multidrug-resistant cells

Pentacyclic thio- (1) and seleno- (2) analogues of tetramethylrosamine (TMR) were prepared with a julolidyl fragment replacing the 3-dimethylamino substituent in the xanthylium core. The pentacylic structure increases the lipophilicity of 1 and 2 relative to TMR-S and TMR-Se and locks the lone-pair of electrons on the julolidyl N atom into conjugation with the xanthylium core. This conformational rigidization leads to longer wavelengths of absorption, but has little impact on other photophysical properties such as quantum yields for fluorescence and singlet-oxygen generation and fluorescence lifetimes in 1 and 2 relative to TMR-S and TMR-Se. Both 1 and 2 are effective photosensitizers against chemosensitive AUXB1 cells in vitro at 1 × 10⁻⁷ M and compound 2 is an effective photosensitizer against multidrug-resistant CR1R12 cells in vitro at 1 × 10⁻⁷ M. While the uptake TMR-S into CR1R12 cells as measured by fluorescence is significantly lower than uptake into chemosensitive AUXB1 cells, there is no significant difference in the uptake of 1 into either AUXB1 or CR1R12 cells. The addition of 2 × 10⁻⁴ M verapamil to the cells prior to treatment with 1 had no significant effect on the uptake of 1 into either AUXB1 or CR1R12 cells. Treating lipid-activated, purified Pgp with 2 and light gave complete inhibition of Pgp ATPase activity.