共查询到20条相似文献,搜索用时 15 毫秒
1.
《仿生工程学报(英文版)》2008
Bone is a natural biomaterial. It behaves favorable strength, stiffness and fracture toughness, which are closely related to its eximious microstructure. Scanning Electron Microscope (SEM) observation on a shinbone showed that the bone is a bioceramic composite consisting of laminated hydroxyapatite and collagen matrix. The hydroxyapatite layers are parallel with the surface of the bone and consist of long and thin hydroxyapatite sheets. The observation also showed that the hydroxyapatite sheets in different hydroxyapatite layers also parallel with each other, which composes a hydroxyapatite-sheet parallel microstructure. The maximum pullout energy of the parallel microstructure was investigated based on its representative model. It was shown that the long and thin shape of the hydroxyapatite sheets in the parallel microstructure is profitable to increase the maximum pullout energy and enhance the fracture toughness of the bone. 相似文献
2.
An experimental and computational study of screw pullout from cortical bone has been conducted. A novel modification of standard pullout tests providing real time image capture of damage mechanisms during screw pullout was developed. Pullout forces, measured using the novel test rig, have been validated against standard pullout tests. Pullout tests were conducted, considering osteon alignment, to investigate the effect of osteons aligned parallel to the axis of the orthopaedic screw (longitudinal pullout) as well as the effect of osteons aligned perpendicular to the axis of the screw (transverse pullout). Distinctive alternate failure mechanisms, for longitudinally and transversely orientated cortical bone during screw pullout, were uncovered. Vertical crack propagation, parallel to the axis of the screw, was observed for a longitudinal pullout. Horizontal crack propagation, perpendicular to the axis of the screw, was observed for a transverse pullout. Finite element simulation of screw pullout, incorporating material damage and crack propagation, was also performed. Simulations revealed that a homogenous material model for cortical bone predicts vertical crack propagation patterns for both longitudinal and transverse screw pullout. A bi-layered composite model representing cortical bone microstructure was developed. A unique set of material and damage properties was used for both transverse and longitudinal pullout simulations, with only layer orientations being changed. Simulations predicted: (i) higher pullout forces for transverse pullout; (ii) horizontal crack paths perpendicular to screw axis for transverse pullout, whereas vertical crack paths were computed for longitudinal pullout. Computed results agreed closely with experimental observations in terms of pullout force and crack propagation. 相似文献
3.
Vincent A. Stadelmann Elise Bretton Alexandre Terrier Philip Procter Dominique P. Pioletti 《Journal of biomechanics》2010,43(15):2869-2874
An obvious means to improve the fixation of a cancellous bone screw is to augment the surrounding bone with cement. Previous studies have shown that bone augmentation with Calcium Phosphate (CaP) cement significantly improves screw fixation. Nevertheless, quantitative data about the optimal distribution of CaP cement is not available. The present study aims to show the effect of cement distribution on the screw fixation strength for various cortical thicknesses and to determine the conditions at which cement augmentation can compensate for the absence of cortical fixation in osteoporotic bone. In this study, artificial bone materials were used to mimic osteoporotic cancellous bone and cortical bone of varying thickness. These bone constructs were used to test the fixation strength of cancellous bone screws in different cortical thicknesses and different cement augmentation depths. The cement distribution was measured with microCT. The maximum pullout force was measured experimentally. The microCT analysis revealed a pseudo-conic shape distribution of the cement around the screws. While the maximum pullout strength of the screws in the artificial bone only was 30±7 N, it could increase up to approximately 1000 N under optimal conditions. Cement augmentation significantly increased pullout force in all cases. The effect of cortical thickness on pullout force was reduced with increased cement augmentation depth. Indeed, cement augmentation without cortical fixation increased pullout forces over that of screws without cement augmentation but with cortical fixation. Since cement augmentation significantly increased pullout force in all cases, we conclude that the loss of cortical fixation can be compensated by cement augmentation. 相似文献
4.
Pullout of implants at the proximal and distal ends of multilevel constructs represents a common spinal surgery problem. One goal concerning the development of new spinal implants is to achieve stable fixation together with the least invasive approach to the spinal column. This biomechanical study measures the influence of different modes of implantation and different screw designs, including a new monocortical system, on the maximum pullout strength of screws inserted ventrolaterally into calf vertebrae. The force pullout of eight different groups were tested and compared. Included were three bicortical used single screws (USS, Zielke-VDS, single KASS). To further increase pullout strength either a second screw (KASS) or a pullout-resistant nut can be added (USS with pullout nut). A completely new concept of anchorage represents the Hollow Modular Anchorage System (MACS-HMA). This hollow titanium implant has an increased outside diameter and is designed for monocortical use. Additionally two screw systems suitable for bicortical use were tested in monocortical mode of anchorage (USS, single KASS). We selected seven vertebrae equal in mean size and bone mineral density for each of the eight groups. The vertebral body and implant were connected to both ends of a servohydraulic testing machine. Displacement controlled distraction was applied until failure at the metal-bone-interface occurred. The maximum axial pullout force was recorded. Mean BMD was 312 +/- 55 mg CaHA/ml in cancellous bone and 498 +/- 98 mg CaHA/ml in cortical bone. The highest resistance to pullout found, measured 4.2 kN (KASS) and 4.0 kN (USS with pullout nut). The mean pullout strength of Zielke-VDS was 2.1 kN, of single KASS 2.5 kN, of MACS-HMA 2.6 kN and of USS 3.2 kN. There was no statistically significant difference (t-test, p > 0.05) between bicortical screws and the new monocortical implant. For the strongest fixation at the proximal or distal end of long spinal constructs the addition of a second screw or a pullout-resistant nut behind the opposite cortex offers even stronger fixation. 相似文献
5.
Rodríguez-Navarro AB CabraldeMelo C Batista N Morimoto N Alvarez-Lloret P Ortega-Huertas M Fuenzalida VM Arias JI Wiff JP Arias JL 《Journal of structural biology》2006,156(2):355-362
Barnacle shell is a very complex and strong composite bioceramic composed of different structural units which consist of calcite 15 microcrystals of very uniform size. In the study reported herein, the microstructural organization of these units has been examinated in detail with optical and scanning electron microscopy, and X-ray diffraction techniques. These analyses showed that the external part of the shell has a massive microstructure consisting of randomly oriented crystals. Toward the interior, the shell became organized in mineral layers separated by thin organic sheets. Each of these mineral layers has a massive microstructure constituted by highly oriented calcite microcrystals with their c-axes aligned [(001) fibre texture] perpendicular to the organic sheets and the shell surface. Interestingly, in another structural unit, the shell shield, the orientation of the c-axis calcite crystals shifts from being perpendicular to being parallel to the shell surface across its thickness. This study provides evidence that the organic matrix is responsible for the organization of the shell mineral and exterts strong a strict control on the polymorphic type, size and orientation of shell-forming crystals. 相似文献
6.
Mariya Poukalova Christopher M. Yakacki Robert E. Guldberg Angela Lin Minn Saing Scott D Gillogly Ken Gall 《Journal of biomechanics》2010,43(6):1138-1145
This study investigated the relationships between trabecular microstructure and elastic modulus, compressive strength, and suture anchor pullout strength. Twelve fresh-frozen humeri underwent mechanical testing followed by micro-computed tomography (μCT). Either compression testing of cylindrical bone samples or pullout testing using an Arthrex 5 mm Corkscrew was performed in synthetic sawbone or at specific locations in the humerus such as the greater tuberosity, lesser tuberosity, and humeral head. Synthetic sawbone underwent identical mechanical testing and μCT analysis. Bone volume fraction (BVF), structural model index (SMI), trabecular thickness (TbTh), trabecular spacing (TbSp), trabecular number (TbN), and connectivity density were compared against modulus, compressive strength, and pullout strength in both materials. In cadaveric bone, modulus showed correlations to all of the microstructural properties, while compressive and pullout strength were only correlated to BVF, SMI, and TbSp. The microstructure of synthetic bone differed from cadaveric bone as SMI and TbTh showed little variation across the densities tested. Therefore, SMI and TbTh were the only microstructural properties that did not show correlations to the mechanical properties tested in synthetic bone. This study helps identify key microstructure–property relationships in cadaveric and synthetic bone as well as illustrate the similarities and differences between cadaveric and synthetic bone as biomechanical test materials. 相似文献
7.
Christopher M. Yakacki Mariya Poukalova Robert E. Guldberg Angela Lin Minn Saing Scott Gillogly Ken Gall 《Journal of biomechanics》2010,43(10):1953-1959
This study investigates how the microstructural properties of trabecular bone affect suture anchor performance. Seven fresh-frozen humeri were tested for pullout strength with a 5 mm Arthrex Corkscrew in the greater tuberosity, lesser tuberosity, and humeral head. Micro-computed tomography analysis was performed in the three regions of interest directly adjacent to individual pullout experiments. The morphometric properties of bone mineral density (BMD), structural model index (SMI), trabecular thickness (TbTh), trabecular spacing (TbS), trabecular number (TbN), and connectivity density were compared against suture anchor pullout strength. BMD (r=0.64), SMI (r=?0.81), and TbTh (r=0.71) showed linear correlations to the pullout strength of the suture anchor with p-values<0.0001. A predictive model was developed to explain the variances in the individual BMD, SMI, and TbTh correlations. The multi-variant model of pullout strength showed a stronger relationship (r=0.86) compared to the individual experimental results. This study helps confirm BMD is a major influence on the pullout strength of suture anchors, but also illustrates the importance of local microstructure in pullout resistance of suture anchors. 相似文献
8.
A systematic analysis of the hydrogen-bonding geometry in helices and beta sheets has been performed. The distances and angles between the backbone carbonyl O and amide N atoms were correlated considering more than 1500 protein chains in crystal structures determined to a resolution better than 1.5 A. They reveal statistically significant trends in the H-bond geometry across the different secondary structural elements. The analysis has been performed using Secbase, a modular extension of Relibase (Receptor Ligand Database) which integrates information about secondary structural elements assigned to individual protein structures with the various search facilities implemented into Relibase. A comparison of the mean hydrogen-bond distances in alpha helices and 3(10) helices of increasing length shows opposing trends. Whereas in alpha helices the mean H-bond distance shrinks with increasing helix length and turn number, the corresponding mean dimension in 3(10) helices expands in a comparable series. Comparing similarly the hydrogen-bond lengths in beta sheets there is no difference to be found between the mean H-bond length in antiparallel and parallel beta sheets along the strand direction. In contrast, an interesting systematic trend appears to be given for the hydrogen bonds perpendicular to the strands bridging across an extended sheet. With increasing number of accumulated strands, which results in a growing number of back-to-back piling hydrogen bonds across the strands, a slight decrease of the mean H-bond distance is apparent in parallel beta sheets whereas such trends are obviously not given in antiparallel beta sheets. This observation suggests that cooperative effects mutually polarizing spatially well-aligned hydrogen bonds are present either in alpha helices and parallel beta sheets whereas such influences seem to be lacking in 3(10) helices and antiparallel beta sheets. 相似文献
9.
Background and Aims
The quantification of root reinforcement function is important for landscape managers and engineers. The estimation of root mechanical reinforcement is often based on models that do not consider the potential interaction between neighbouring roots. Root-soil mechanical interactions related to the root spacing and bundle geometry remain unclear including potential effects on the reliability of the current models. The objective of this study is to quantify the mechanical interactions among neighbouring roots or roots networks using modelling approaches and pullout laboratory experiments.Methods
Based on simple geometrical characterization of individual root geometry, we calculated dissipation patterns of frictional root-soil interfacial stresses in radial and longitudinal directions. Considering simple superposition of shear stresses within the soil matrix, we quantified characteristic root densities at which the radial mechanical interactions influence global pullout behaviour of the root bundle both for branched and unbranched roots. Laboratory pullout tests on root bundles were carried out at root spacings of 15, 35 and 105 mm. In addition, we tested effects of non-parallel (crossing) root bundle geometry.Results
We found no significant statistical differences in root pullout force for the different root spacing in parallel alignment of roots. Branches increase pullout force by 1.5 times. Moreover, the mean displacement at the pullout peak-force was 7.2 % of length for unbranched roots and about 4.1 % of length for branched roots. The model shows its potential comparing it with empirical results concerning the holes leaved by roots, according with the branch pattern.Conclusion
The study quantifies the influence of root spacing and arrangement geometry within a root bundle on its mechanical behaviour. The assumption of “non-interacting” neighbouring roots in root reinforcement methods is no longer valid for root spacing less than 15 mm and root reinforcement methods. Moreover crossing roots shown a statistical difference. This information is important for improved understanding root reinforcement mechanisms in steep hill slope and the interplay between anchoring /failure and root bundle pullout vs root breakage. 相似文献10.
Koichi Okamoto Brian Lin Keisuke Imazu Akihito Yoshida Koji Toma Mana Toma Kaoru Tamada 《Plasmonics (Norwell, Mass.)》2013,8(2):581-590
We report a new concept of tuning plasmonic colors of two-dimensional crystalline silver nanoparticle sheets with layer-by-layer structures. The multilayered crystalline sheets fabricated by the Langmuir–Schaefer method keep the localized surface plasmon resonance bands at the same position (λ max?=?465 nm) on quartz, while they change their colors drastically on metal substrates depending on the number of layers (one to five layers). The response of the absorption spectra was absolutely nonlinear, with maximum absorption for two or three layers. The obtained results were well reproduced by the finite difference time domain simulation. The simulation confirmed that these plasmonic colors originate not only from near-field coupling of plasmon resonance but also far-field nano-optics of the multilayered silver nanoparticle sheets. 相似文献
11.
Biological composite materials, such as bone, tooth and nacre, are comprised of a mixture of nano-sized hard components (e.g. mineral platelets) and soft components (e.g. protein molecules). Their mechanical behaviour greatly depends on the protein–mineral interfaces. This paper investigates the effects of mineral surface nanostructures on the interfacial interaction and mechanical behaviour of protein–mineral nanocomposites. Interfacial shear between osteopontin (OPN) and hydroxyapatite (HA) mineral layers with surface nanostructures is investigated using the atomistic molecular dynamics (MD) simulations. The results indicate that the OPN residues can be attached to HA surfaces but the surface nanostructures greatly affect the interfacial interaction and mechanical behaviour. The HA layers with a higher number of nano-sized grooves (defects) increase the surface roughness but reduce the pulling force and energy dissipation. 相似文献
12.
Impact of the porous microstructure on the overall elastic properties of the osteonal cortical bone 总被引:5,自引:0,他引:5
Mechanical properties of bones are largely determined by their microstructure. The latter comprises a large number of diverse pores. The present paper analyzes a connection between structure of the porous space of the osteonal cortical bone and bone's overall anisotropic elastic moduli. The analysis is based on recent developments in the theory of porous materials that predict the anisotropic effective moduli of porous solids in terms of pores' shapes, orientations and densities. Bone's microstructure is modeled using available micrographs. The calculated anisotropic elastic constants for porous cortical bone are, mostly, in agreement with available experimental data. The influence of each of the pore types on the overall moduli is examined. The results of the analysis can also be used to estimate the extent of mineralization (hydroxyapatite content) if the overall porosity and the effective moduli are known and, vice versa, to estimate porosity from the measured moduli and the extent of mineralization. 相似文献
13.
《Geobios》2016,49(4):319-327
The mantle tissue is essential for understanding the diverse ecology and shell morphology of ammonoid cephalopods. Here, we report on irregular calcareous sheets in a well-preserved shell of a Late Cretaceous phylloceratid ammonoid Hypophylloceras subramosum from Hokkaido, Japan, and their significance for repairing the conch through the mantle inside the body chamber. The sheets are composed of nacreous layers arranged parallel to the irregularly distorted outer whorl surface. The nacreous sheets formed earlier are unevenly distributed and attached to the outer shell wall locally, whereas the last formed sheet covers a wide area of the outer shell wall. The absence of any interruption of ribbing around the irregular area suggests that these sheets were secreted inside the body chamber from the inner mantle. Gross morphological and X-ray computed tomography observations revealed that the spacing of septal formation was not affected by this event. The complex structure of the irregular sheets suggests a highly flexible mantle inside the body chamber. 相似文献
14.
Dynamics of formation and morphological features of neutrophil extracellular traps formed under the influence of opsonized Staphylococcus aureus
下载免费PDF全文
![点击此处可从《Journal of molecular recognition : JMR》网站下载免费的PDF全文](/ch/ext_images/free.gif)
Svetlana N. Pleskova Ekaterina N. Gorshkova Ruslan N. Kriukov 《Journal of molecular recognition : JMR》2018,31(7)
In the process of performing their protective functions, neutrophils can form neutrophil extracellular traps (NETs), consisting of DNA in combination with enzymes and histones. The aim of the study was to determine the dynamics of the formation of NETs under the influence of opsonized Staphylococcus aureus and to determine the morphological features of their development in real time by atomic force microscopy. It was found that the maximum formation of NETs was observed after 3 hours of co‐incubation of neutrophils and opsonized S. aureus. For the first time, the atomic force microscopy method revealed that, at first, large blocks of parallel DNA helices are formed, which then spread in waves, and only then their bifurcation and separation can be observed. Some of the strands formed are covered by a shell, which subsequently completely disappears. Enzymes and histones become clearly visible only after 140 to 150 minutes of observation. The DNA helixes move toward the opsonized S. aureus. After NET formation, the cell remains on the substrate only in the form of traces of focal adhesion. This, and the fact that the maximum amount of NETs is formed after 3 hours of co‐incubation with opsonized S. aureus, suggests that the formation of NETs follows the classical mechanism. The study of the dynamics of formation and the microstructure of NETs makes it possible to estimate the time frame for the implementation of this protective mechanism of the human body when performing the compensatory inflammatory reaction. 相似文献
15.
Custom-shaping system for bone regeneration by seeding marrow stromal cells onto a web-like biodegradable hybrid sheet 总被引:2,自引:0,他引:2
Tsuchiya K Mori T Chen G Ushida T Tateishi T Matsuno T Sakamoto M Umezawa A 《Cell and tissue research》2004,316(2):141-153
New bone for the repair or the restoration of the function of traumatized, damaged, or lost bone is a major clinical need, and bone tissue engineering has been heralded as an alternative strategy for regenerating bone. A novel web-like structured biodegradable hybrid sheet has been developed for bone tissue engineering by preparing knitted poly(DL-lactic-co-glycolic acid) sheets (PLGA sheets) with collagen microsponges in their openings. The PLGA skeleton facilitates the formation of the hybrid sheets into desired shapes, and the collagen microsponges in the pores of the PLGA sheet promote cell adhesion and uniform cell distribution throughout the sheet. A large number of osteoblasts established from marrow stroma adhere to the scaffolds and generate the desired-shaped bone in combination with these novel sheets. These results indicate that the web-like structured novel sheet shows promise for use as a tool for custom-shaped bone regeneration in basic research on osteogenesis and for the development of therapeutic applications.This work was supported in part by a grant from the Ministry of Education, Culture, Sports, Science, and Technology of Japan, Health and Labour Sciences Research Grants (translational research), and the Organization for Pharmaceutical Safety and Research (to A.U.) 相似文献
16.
Shenghui Chen Shuangqing Sun Chunling Li Charles U. Pittman Jr. Thomas E. Lacy 《Molecular simulation》2018,44(12):947-953
Molecular dynamics simulations were used to investigate the aggregation of two partially overlapped graphene sheets in hexane, dodecane and eicosane. When partially overlapped graphene sheets are adjacent to one another, they will expel the adsorbed layers of the solvent molecules on the graphene surface, and the amount of overlap will increase. When the overlapped regions of the graphene sheets are separated by solvent molecules, they cannot expel the adsorption layers between them, and so the sheets remain separated. The driving force for aggregation is the van der Waals interaction between the two graphene sheets, while the van der Waals interaction between the graphene sheets and the solvent molecules inhibits graphene aggregation. The diffusion rate of the hydrocarbon molecules with shorter chain lengths is higher. Thus, they diffuse faster during graphene aggregation, which leads to a higher rate of graphene overlapping in the shorter hydrocarbons. This work provides useful insights into graphene aggregation in linear hydrocarbon solvents of varying lengths at the nanoscale. 相似文献
17.
Gastrulation in C. elegans embryos involves ingression of individual cells, but is driven by apical constriction of the kind that promotes migration of epithelial cell sheets. Recent work shows that PAR proteins, known for their role in polarization and unequal cell division, are also associated with the polarization that establishes this apical constriction. 相似文献
18.
H N Christensen M E Handlogten 《Biochemical and biophysical research communications》1981,98(1):102-107
EXPFS spectra have been recorded from bone mineral and related calcium phosphates. Fourier transformation of a spectrum, using theoretically calculated phase shifts, yields a good approximation to the radial distribution of atoms around a calcium ion. Comparison of the results shows that bone mineral is appreciably different from crystalline synthetic hydroxyapatite and geological apatites, which are similar to each other, but closely resembles hydroxyapatite obtained by maturation of amorphous calcium phosphate. 相似文献
19.
Petar Liovic Ilija D. Šutalo Silvana F. Marasco 《Computer methods in biomechanics and biomedical engineering》2014,17(9):944-957
The stress on an intramedullary screw rib fixation device holding together a centrally fractured human rib under in vivo force loadings was studied using finite element analysis (FEA). Validation of the FEA modelling using pullout from porcine ribs proved FEA to be suitable for assessing the structural integrity of screw/bone systems such as rib fixated by a screw. In the human rib fixation investigation, it was found that intramedullary bioresorbable Bioretec screws can fixate centrally fractured human ribs under normal breathing conditions. However, under coughing conditions, simulation showed Bioretec fixating screws to bend substantially. High stresses in the screw are mainly the result of flexion induced by the force loading, and are restricted to thin regions on the outside of the screw shaft. Stiffer screws result in less locally intense stress concentrations in bone, indicating that bone failure in the bone/screw contact regions can be averted with improvements in screw stiffness. 相似文献
20.
Gastropod shells from Lake Tanganyika, with their heavy calcification, coarse noded ribbing, spines, apertural lip thickening and repair scars, resemble marine shells more closely than they resemble other lacustrine shells. This convergence between Tanganyikan and marine gastropod shells, however, is not just superficial. Scanning electron microscope (SEM) studies reveal that the Tanganyikan shells are primarily layers of crossed-lamellar crystal architecture (that is, needle-like aragonite crystals arranged into laths that are packed into sheets such that the aragonite needles of adjacent laths are never parallel). The number of crossed-lamellar layers can vary from one to four between different Tanganyikan gastropod species. In species with two or more crossed-lamellar layers, the orientation of the lamellae is offset by approximately 90° between the different layers. The number of crossed-lamellar layers in the shell wall is positively correlated with shell strength and with predation resistance. Three and four crossed-lamellar layers in the shell wall evolved several times independently within the endemic thiarid gastropod radiation in Lake Tanganyika. Repeated origins of three and four crossed-lamellar layers suggest that they may be specific adaptations by Tanganyikan gastropods to strengthen their shells as a defense against shell-crushing predators. 相似文献