The effects of amylose content on the molecular size of amylose, and on the distribution of amylopectin chain length in maize starches

The amylose to amylopectin ratios in six maize starch samples of differing amylose contents were measured by enzymatic debranching, followed by high performance size exclusion chromatography (HPSEC). The molecular size of amyloses, estimated by -log K_wav, shows progressive decrease with the increase in amylose content in maize starches. The gel permeation chromatographs of the corresponding amylopectins, debranched with isoamylase, showed bimodal distributions containing long and short chains. The average chain length of amylopectin has a correlation with amylose content. The correlation coefficients between amylose content and average chain length, long chain length, weight ratio and the mole ratio of long and short chain length, were 0.97, 0.92, 0.96, 0.94 respectively. The maize starch with the highest amylose content has the lowest amylose molecular size and the longest chains, with a high ratio of long to short chains in its amylopectin fraction. Comparing the values of amylose content determined by HPSEC of starch or debranched starch with those of the iodinecomplex method, we conclude that long chains of amylopectin in high amylose starches contribute significantly to apparent amylose content.     

Effects of amylose/amylopectin ratio on starch-based superabsorbent polymers

Biodegradable superabsorbent polymers (SAPs) were prepared by grafting acrylamide onto starches then crosslinking with N,N′-methylene-bisacrylamide. This work focused on the effects of the amylose/amylopectin ratio of starches from the same source (corn) on the grafting reactions and performance of the resultant starch-based SAPs. To characterise each SAP, the acrylamide groups grafted onto the starch were detected by FTIR; grafting ratio and grafting efficiency were evaluated by a gravimetric method; and graft position and the length of the grafted segment were investigated by NMR. The relationships between the microstructures of the starches, and the graft reactions and performance of the SAPs were studied based on the amylose content in the starches. It was found that under the same reaction conditions, the grafting ratio and efficiency increased with increasing amylose content, which corresponds with water absorption ratio. NMR results indicated that the acrylamide group mainly grafted onto C6, and that the length of the grafted segment decreased with increasing amylopectin content in general, and in particular for waxy starch. The high molecular weight and branched structure of amylopectin reduced the mobility of the polymer chains and increased viscosity, which could explain the graft reactions and performance of the starch-based SAPs.     

Iodine binding property of a ternary complex consisting of starch,protein, and free fatty acids

A ternary complex consisting of amylose, whey protein, and free fatty acids (FFA) has been identified in our previous investigations, and its iodine binding properties were investigated. After reaction with iodine solution, an absorption peak (λ_max) at 620 nm was shown for pure amylose whereas the λ_max decreased to 510 nm when amylose was first complexed with FFA. Interestingly, a λ_max of 550 nm with an intermediate absorbance was observed for the ternary complex indicating its intermediate spectrophotometric property. Consistently, the amount of iodine bound by the ternary complex was between free amylose and typical amylose–FFA complex from potentiometric titration indicating the amylose–FFA complex within the ternary complex is less compact and more space is left for iodine binding. This in-between property of the ternary complex suggests it can be used as a molecular carrier to accommodate a forth component in addition to its functional lipids carrying capability in food product development.     

The α(1–4)(1–6) glucans from sweet and normal corns

After removal of granular starch at low centrifugal force, the centrifugation, at increasing forces, of aqueous extracts of su₁ corn gave a series of α-glucan precipitates that contained amylose. The amylose content decreased as the force increased. In contrast, in normal corn all the α-glucan precipitated as starch granules at low forces. In the sweet corn precipitates, apart from the granular starch, the branched α-glucan was phytoglycogen. The MW of this decreased as the proportion of amylose decreased. It appears that, as well as starch granules and soluble phytoglycogen, sweet corn contains granules, smaller than starch, of a range of sizes, and these are made up of phytoglycogen and amylose. As granule size decreases, so does the MW of the phytoglycogen and the content of amylose. A method of quantitative extraction of starch giving minimal depolymerization is described. The isopotential iodine absorption of a quantitative extract of sweet corn flour indicated that the total ratio of linear (amylose) fraction to branched (amylopectin + phytoglycogen) fraction was near the normal value of 1:4.     

Characterization of barley starches of waxy, normal, and high amylose varieties

Four varieties of barley starches, W.B. Merlin, glacier, high amylose glacier, and high amylose hull-less glacier, were isolated from barley seeds. Apparent and absolute amylose contents, molecular size distributions of amylose and amylopectin, amylopectin branch-chain-length distributions, and Naegeli dextrin structures of the starches were analyzed. W.B. Merlin amylopectin had the longest detectable chain length of DP 67, whereas glacier, high amylose glacier and high amylose hull-less glacier amylopectins had the longest detectable chain length of DP 82, 79, and 78, respectively. All the four starches displayed a substantially reduced proportion of chains at DP 18–21. Amylopectins of high amylose varieties did not show significantly larger proportions of long chains than that of normal and waxy barley starch. Onset gelatinization temperatures of all four barley starches ranged from 55.0 to 56.5°C. Absolute amylose contents of W.B. Merlin, glacier, high amylose glacier, and high amylose hull-less glacier were 9.1, 29.5, 44.7, and 43.4%, respectively; phospholipid contents were 0.36, 0.78, 0.79, and 0.97%, respectively.     

Size distributions of amylose and amylopectin solubilized from corn starch granules

Size distributions of extracts derived from starch were investigated to aid in elucidating structure-function relationships of these polymers in water. Starch granules derived from waxy maize and amylomaize VII were dissolved in water by microwave heating in a high pressure vessel. Transmission electron microscopy of starch deposited from dilute solution and rotary shadowed with platinum, revealed that amylopectin imaged from waxy maize could be broadly classified as about 28% circular space filling patches containing branched clusters and 72% asymmetric linear containing branched clusters. Lengths of asymmetric linear amylopectin components ranged from about 37 to 980 nm whereas the diameter of circular amylopectin components ranged from about 44 to 200 nm. Although the starch in amylomaize VII is about 70% amylose, its narrow asymmetric structure when visualized by microscopy enabled us to image amylose even though amylopectin was present. Lengths of components ranged from about 46 to 254 nm. After smoothing and curve fitting, we found that all size distributions investigated could be treated as if they were multimodal in nature. The most abundant amylose component had a linear density of 8.2 × 10³ molar mass units/ nm. This value could be explained if amylose had an aggregation number of about 5.9.     

Internal structure and physicochemical properties of corn starches as revealed by chemical surface gelatinization

The organization of amylose and amylopectin within starch granules is still not well elucidated. This study investigates the radial distribution of amylose and amylopectin in different corn starches varying in amylose content (waxy corn starch (WC), common corn starch (CC), and 50% and 70% amylose corn starches (AMC)). Corn starches were surface gelatinized by 13 M LiCl at room temperature to different extents (approximately 10%, 20%, 30%, and 40%). The gelatinized surface starch and remaining granules were characterized for amylose content, amylopectin chain-length distribution, thermal properties, swelling power (SP), and water solubility index (WSI). Except for the outmost 10% layer, the amylose content in CC increased slightly with increasing surface removal. In contrast, amylose was more concentrated at the periphery than at the core for 50% and 70% AMC. The proportion of amylopectin A chains generally decreased while that of B1 chains generally increased with increasing surface removal for all corn starches. The gelatinization enthalpy usually decreased, except for 70% AMC, whereas the retrogradation enthalpy relatively remained unchanged for CC but increased for WC, 50% and 70% AMC with increasing surface removal. The SP and WSI increased with increasing surface removal for all corn starches, with WC showing a significant increase in SP after the removal of the outmost 10% layer. The results of this study indicated that there were similarities and differences in the distribution of amylose and amylopectin chains along the radial location of corn starch granules with varying amylose contents. More amylose-lipid complex and amylopectin long chains were present at the periphery than at the core for amylose-containing corn starches.     

Temperature induced changes in the starch components and biosynthetic enzymes of two rice varieties

The effects of temperature on starch and amylose accumulation, fine structure of amylopectin and activities of some enzymes related to starch synthesis in developing rice endosperms was examined. Two early indica rice varieties were used, differing in amylose concentration (AC, %), namely Jia 935 (low AC) and Jia 353 (high AC). The results showed that the effects of high temperature on AC and amylopectin fine structure were variety-dependent. High temperature caused a reduction in amylose concentration and an increase in the short chain (CL<22) proportion of amylopectin for Jia 935; while opposite was true for Jia 353. High temperature also reduced and increased the activity of granule-bound starch synthase (GBSS) in Jia 935 and in Jia 353, respectively. This suggests that a change in the ratio of amylose/starch due to temperature was attributable to a change in GBSS activity. Moreover, obvious differences between the two rice varieties were detected in the activities of sucrose synthase (SuSy), ADP-glucose pyrophosphorylase (ADPG-Ppase), soluble starch synthase (SSS), starch branching enzyme (SBE), starch de-branching enzyme (SDBE) and starch phosphorylase (SPase) to high temperature. Accumulation rate of amylose was significantly and positively correlated with GBSS for Jia 935, but not for Jia 353. Amylose accumulation was also significantly and positively correlated with the activities of SDBE, SBE, ADPG-Ppase and SuSy for both varieties. The results suggest that the ratio of amylose to starch in rice endosperm is not only related to GBSS, but also affected by the activities of SDBE, SBE, ADPG-Ppase and SuSy.     

Quantification of total iodine in intact granular starches of different botanical origin exposed to iodine vapor at various water activities

Iodine has been used as an effective tool for studying both the structure and composition of dispersed starch and starch granules. In addition to being employed to assess relative amylose contents for starch samples, it has been used to look at the molecular mobility of the glucose polymers within intact starch granules based on exposure to iodine vapor equilibrated at different water activities. Starches of different botanical origin including corn, high amylose corn, waxy corn, potato, waxy potato, tapioca, wheat, rice, waxy rice, chick pea and mung bean were equilibrated to 0.33, 0.75, 0.97 water activities, exposed to iodine vapor and then absorbance spectra and LAB color were determined. In addition, a new iodine quantification method sensitive to <0.1% iodine (w/w) was employed to measure bound iodine within intact granular starch. Amylose content, particle size distribution of granules, and the density of the starch were also determined to explore whether high levels of long linear glucose chains and the surface area-to-volume ratio were important factors relating to the granular iodine binding. Results showed, in all cases, starches complexed more iodine as water content increased and waxy starches bound less iodine than their normal starch counterparts. However, much more bound iodine could be measured chemically with waxy starches than was expected based on colorimetric determination. Surface area appeared to be a factor as smaller rice and waxy rice starch granules complexed more iodine, while the larger potato and waxy potato granules complexed less than would be expected based on measured amylose contents. Corn, high amylose corn, and wheat, known to have starch granules with extensive surface pores, bound higher levels of iodine suggesting pores and channels may be an important factor giving iodine vapor greater access to bind within the granules. Exposing iodine vapor to moisture-equilibrated native starches is an effective tool to explore starch granule architecture.     

Physico-chemical and degradative properties of in-planta re-structured potato starch

Starch re-structured directly in potato tubers by antisense suppression of starch branching enzyme (SBE), granule bound starch synthase (GBSS) or glucan water dikinase (GWD) genes was studied with the aim at disclosing the effects on resulting physico-chemical and enzyme degradative properties. The starches were selected to provide a combined system with specific and extensive alterations in amylose and covalently esterified glucose-6-phosphate (G6P) contents. As an effect of the altered chemical composition of the starches their hydrothermal characteristics varied significantly. Despite of the extreme alterations in phosphate content, the amylose content had a major affect on swelling power, enthalpy for starch gelatinization and pasting parameters as assessed by Rapid Visco Analysis (RVA). However, a combined influence of the starch phosphate and long glucan chains as represented by high amylose or long amylopectin chain length was indicated by their positive correlation to the final viscosity and set back (RVA) demonstrating the formation of a highly hydrated and gel-forming system during re-structuring of the starch pastes. Clear inverse correlations between glucoamylase-catalyzed digestibility and amylopectin chain length and starch phosphate and lack of such correlation with amylose content indicates a combined structuring role of the phosphate groups and amylopectin chains on the starch glucan matrix.     

Gel formation in mixtures of high amylopectin potato starch and potato starch

The effects of starch granules on the rheological behaviour of gels of native potato and high amylopectin potato (HAPP) starches have been studied with small deformation oscillatory rheometry. The influence of granule remnants on the rheological properties of samples treated at 90 °C was evident when compared with samples treated at 140 °C, where no granule remnants were found. The presence of amylose in native potato starch gave to stronger network formation since potato starch gave higher moduli values than HAPP, after both 90 and 140 °C treatments. In addition, amylose may have strengthened the network of HAPP because higher moduli values were obtained when native potato starch was added to the system. The moduli values of the mixtures also increased with increasing polysaccharide concentration in the system, which is due to an increment in the polysaccharide chain contacts and entanglements. Finally, it was found that a mixture of commercial amylose from potato starch and HAPP resulted in lower values of G′ compared to native potato starch. This indicates that the source of amylose is important for the properties in a blend with native amylopectin.     

ON THE MOLECULAR STRUCTURE OF STARCH GRANULES

It is a problem how to fit the molecules of amylose and amylopectin into the ultrastructural apposition layers of starch granules which have a width of only 0.1μ. Stretched amylose chains with a length up to 1 μ can be ruled out. In addition to the proposal of Miihlethaler, who visualizes folded amylopectin chains, a model with a helical amylose chain is discussed. A helix with six glucose residues per turn would be compatible with the crystal lattice found by Kreger; and the disorder caused by this helix in the hexagonal lattice of the parallel side chains of the amylopectin would account for the low optical anisotropy of the starch granules as compared to the parallel β-polyglucosan chains in cellulose. The proposed model, fitted into the 0.1 μ apposition ring of the starch granule, shows tangential strata with a layer repeat of about 80 A and a radial chain lattice with the fibre period 10.6 A; i.e., it shows a combination of a lamellar and a fibrous structure.     

Distribution of methyl substituents in amylose and amylopectin from methylated potato starches

Granular potato starches were methylated in aqueous suspension with dimethyl sulfate to molar substitution (MS) values up to 0.29. Fractions containing mainly amylose or amylopectin were obtained after aqueous leaching of the derivatised starch granules. Amylopectin in these fractions was precipitated with Concanavalin A to separate it from amylose. Amylose remained in solution and was enzymatically converted into D-glucose for quantification, thereby taking into account the decreased digestibility due to the presence of methyl substituents. It was found that the MS of amylose was 1.6-1.9 times higher than that of amylopectin in methylated starch granules. The distributions of methyl substituents in trimers and tetramers, prepared from amylose- or amylopectin-enriched fractions, were determined by FAB mass spectrometry and compared with the outcome of a statistically random distribution. It turned out that substituents in amylopectin were distributed heterogeneously, whereas substitution of amylose was almost random. The results are rationalised on the basis of an organised framework that is built up from amylopectin side chains. The crystalline lamellae are less accessible for substitution than amorphous branching points and amylose.     

Acetyl substitution patterns of amylose and amylopectin populations in cowpea starch modified with acetic anhydride and vinyl acetate

To study the effect of reagent type on the distribution pattern of acetyl groups in acetylated cowpea starch, amylose and amylopectin populations were isolated from the starch granules after modification to a low degree of substitution (DS < 0.1) with acetic anhydride and vinyl acetate, respectively. Slowly reacting reagent vinyl acetate resulted in higher DS values for the amylopectin populations when compared to the rapidly reacting reagent acetic anhydride. The two reagents had similar effects on the acetylation level of amylose, suggesting that the amorphous regions of granules were easily accessible for both reagents. The acetyl substitution patterns were analyzed by enzymatic degradation followed by characterization of the obtained fragments using chromatographic and mass spectrometric techniques. The distributions of acetyl groups along the amylose and amylopectin chains were more clustered for modification with vinyl acetate as compared with modification with acetic anhydride. Between the two acetylation types, pronounced differences in the acetyl substitution patterns were observed for the large fragments obtained after -amylase digestion; only slight differences were exhibited for the small fragments obtained by exhaustive enzymatic digestion of amylose and amylopectin populations.     

Studies on the metabolism of the protozoa. The molecular structure of a starch-type polysaccharide from Polytoma uvella

1. Polytoma uvella, when grown in an acetate-containing medium, synthesizes a starch-type polysaccharide. 2. The starch differs from normal plant starches in having a lower iodine affinity, and in being relatively insoluble; this latter property makes fractionation difficult. 3. The starch contains about 16% of amylose, and on fractionation yields a branched amylopectin component that is similar in structure to a typical plant starch amylopectin.     

Improved methods for the structural analysis of the amylose-rich fraction from rice flour

Cooking and sensory properties of rice are largely determined by the amylose content and structure. For relationships between functional and structural properties, a more accurate method to determine the structure of amylose is required. Here we calibrate size exclusion chromatography (SEC) columns, using Mark-Houwink parameters for linear starch and pullulan standards, to obtain the true molecular weight distribution of linear starch. When the molecular weight distribution is reported relative to pullulan, rather than the actual molecular weight which is readily obtained from universal calibration, it is seen that the molecular weights of longer amylose chains are greatly underestimated. We validate the SEC method to enable the measurement of the hydrodynamic volume distribution of the starch by examining reproducibility and recovery. Analysis of the starch in the sample pre- and post-SEC shows that 20% of the carbohydrate is not recovered. Comparison of the weight-average degree of polymerization, X(w), of (undebranched) starch of pre- and post-SEC is made using iodine binding as well as Berry plots of data from multi-angle laser light scattering (MALLS). These both show that current SEC techniques for starch analysis lead to significant loss of high molecular weight material. Indeed, for the systems studied here, the values for X(w) after SEC are about three times lower than those before SEC. Iodine-starch complexes of pre- and post-SEC samples reveals that the SEC techniques give reliable data for the amylose fraction but not for amylopectin. We address reports in the literature suggesting that the conventional isoamylase method for debranching starch would lead to incomplete debranching and thus incorrect molecular weight distributions. However, it is shown using (1)H NMR that isoamylase can completely debranch the amylose (to within the detection limit of 0.5%), and by SEC that successive incubation with isoamylase, alpha-amylase, and beta-amylase can degrade the amylose-rich fraction completely to maltose. We develop a method to obtain a hot water soluble fraction (HWSF), rich in undamaged amylose molecules, directly from rice flour, avoiding the structural degradation of previous techniques. With appropriate sample handling, the formation of associations between starch chains is minimized. With the combination of calibrated and validated SEC methods, and an improved extraction of amylose from rice, the X(w) for both HWSF and debranched HWSF are found to be much larger than has previously been reported.     

The molecular deposition of transgenically modified starch in the starch granule as imaged by functional microscopy

The molecular deposition of starch extracted from normal plants and transgenically modified potato lines was investigated using a combination of light microscopy, environmental scanning electron microscopy (ESEM) and confocal laser scanning microscopy (CLSM). ESEM permitted the detailed (10 nm) topographical analysis of starch granules in their hydrated state. CLSM could reveal internal molar deposition patterns of starch molecules. This was achieved by equimolar labelling of each starch molecule using the aminofluorophore 8-amino-1,3,6-pyrenetrisulfonic acid (APTS). Starch extracted from tubers with low amylose contents (suppressed granule bound starch synthase, GBSS) showed very little APTS fluorescence and starch granules with low molecular weight amylopectin and/or high amylose contents showed high fluorescence. Growth ring structures were sharper in granules with normal or high amylose contents. High amylose granules showed a relatively even distribution in fluorescence while normal and low amylose granules had an intense fluorescence in the hilum indicating a high concentration of amylose in the centre of the granule. Antisense of the starch phosphorylating enzyme (GWD) resulted in low molecular weight amylopectin and small fissures in the granules. Starch granules with suppressed starch branching enzyme (SBE) had severe cracks and rough surfaces. Relationships between starch molecular structure, nano-scale crystalline arrangements and topographical-morphological features were estimated and discussed.     

Starch and its component ratio in developing cotton leaves

During cotton leaf development, starch accumulation was characterized by an initial rise to a maximum at the second to the fourth leaf from the apex. Then, starch content progressively decreased with leaf age. Starch accumulation was inversely related to the ratio of amylopectin to amylose. Differences between leaves in this ratio resulted from variations in both amylose and amylopectin levels. Fluctuations in amylose levels were more extreme than those of amylopectin.     

Variation in crystalline type with amylose content in maize starch granules: an X-ray powder diffraction study

Comparative studies of native maize starches with different amylose contents were carried out using X-ray powder diffraction. The results show a transition of crystalline type from A through C to B, accompanying a decrease in degree of crystallinity from 41.8% to 17.2% across a range of apparent amylose content from 0% to 84%. Hydration induces an increase in degree of granule crystallinity, but does not change the transition of crystal type. Progressively from A-type to C-type, crystallinity decreases rapidly with an increase in amylose content. From C-type to B-type, overall crystallinity decreases more slowly. The crystal type is strongly dependent on amylose content and on average chain length of the respective amylopectin. Waxy A-types have an average chain length of about 20, while in high amylose B-types this rises to ≈35. The proportion of short chains (10–13 glucose units) appears to affect crystal type significantly. Some V-type material was detected at high amylose levels. The proportion of this increased after prolonged exposure of the granules to iodine vapour. Implications for the arrangement of starch components in the granule are discussed.     

A possible structure of retrograded maize starch speculated by UV and IR spectra of it and its components

“Retrogradation” has been used to describe the changes that occur in starch after gelatinization, from an initially amorphous state to a more ordered or crystalline state, which has a significant impact on starch application in food, textiles and materials fields. But mechanism of starch retrogradation is still unclear until now and there is no breakthrough in this area. Here we are speculating a possible structure of retrograded maize starch by UV (binding with iodine) and IR spectra of it and its compositions. We speculate that nucleation of retrograded starch origins from combination of reducing end of amylopectin and non-reducing end of amylose, and retrogradation terminates at combining of non-reducing end of amylopectin and reducing end of amylose. The chain length of resistant digestion retrograded starch should be nearly same. The hydroxyl associated with sixth carbon atoms of glucan must form hydrogen bond with other hydroxyl of starch.