Hydrolysis of soybean oil by lipase with a bioreactor having two different membranes

A membrane bioreactor with 25 sets of two different membranes, one hydrophilic and the other hydrophobic microporous, was used for the hydrolysis of soybean oil by lipase from Candida cylindracea. In the bioreactor, oil, water and enzyme liquid were separately fed into each of 3 clearances between the two membranes. Oil diffused through the hydrophobic membrane and water diffused through the hydrophilic membrane came into contact with the lipase, and hydrolysis subsequently took place. Fatty acid and glycerine produced by the enzymatic reaction diffused through each membrane into the oil and water sides respectively, so that these products were separated from each other. The enzyme was also separated from the products. In this membrane bioreactor, both reaction and separation occurred. Semi-continuous reaction of soybean oil with one cycle of 48 h was carried out for 18 d, at 45°C. Satisfactory performance of the bioreactor, such as a high hydrolysis percentage (92-88%) and enzyme stability over a long-term period was shown. Enzyme stability was found to depend on produced glycerine, as observed by Yamane et al., and the rate of the hydrolysis reaction was controlled by that of the diffusion of fatty acid through the hydrophobic membrane.     

Water repellency,mat formation,and leaf-stimulated growth of some ectomycorrhizal fungi

Summary Ectomycorrhizal short roots, mycelia, rhizomorphs and mats from conifer soil were examined in relation to their hydrophobic properties. In some cases connected fruit bodies were included in the study. Mycorrhizal soils gathered from the forest and/or colonized in a laboratory rhizoscope were studied, as were mycelia in pure culture. Most forest-derived species were hydrophobic. The drought-resistant Cenococcum geophilum and the more ruderal and moisture-dependent Thelephora terrestris were both strongly hydrophilic. The hydrophobic mycelium seemed solely responsible for the water repellence properties, and adjacent soil and plant debris remained unaffected and hydrophilic. In hydrophobic fungi, mat formation was induced in the rhizoscope by hyphal contact with alder litter leaves. This stimulating effect was not found when the leaves were covered by water or when fresh, green alder leaves were used. Thelephora terrestris did not form such mats in vitro and spread sparsely in air pockets as well as in the adjacent water film. The possibility is discussed that many mycorrhizal fungi in the forest may partly control their soil environment via aeration created by their hydrophobia.     

Encapsulation systems for the delivery of hydrophilic nutraceuticals: Food application

Increased health risk associated with the sedentary life style is forcing the food manufacturers to look for food products with specific or general health benefits e.g. beverages enriched with nutraceuticals like catechin, curcumin rutin. Compounds like polyphenols, flavonoids, vitamins are the good choice of bioactive compounds that can be used to fortify the food products to enhance their functionality. However due to low stability and bioavailability of these bioactives (both hydrophobic and hydrophilic) within the heterogeneous food microstructure and in the Gastro Intestinal Tract (GIT), it becomes extremely difficult to pass on the real health benefits to the consumers.Recent developments in the application of nano-delivery systems for food product development is proving to be a game changer which has raised the expectations of the researchers, food manufacturers and consumers regarding possibility of enhancing the functionality of bioactives within the fortified food products. In this direction, nano/micro delivery systems using lipids, surfactants and other materials (carbohydrates, polymers, complexes, protein) have been fabricated to stabilize and enhance the biological activity of the bioactive compounds.In the present review, current status of the various delivery systems that are used for the delivery of hydrophilic bioactives and future prospects for using other delivery systems that have been not completely explored for the delivery of hydrophilic bioactives e.g. niosomes; bilosomes, cubosomes are discussed.     

Mapping domain structures in silks from insects and spiders related to protein assembly

The exceptional solubility in vivo (20-30%, w/v) of the silk proteins of insects and spiders is dictated by both the need to produce solid fibres with a high packing fraction and the high mesogen concentration required for lyotropic liquid crystalline spinning. A further design requirement for silk proteins is a strong predominance of hydrophobic amino acid residues to provide for the hydrophobic interactions, water exclusion, and beta-crystallite formation required to produce strong insoluble threads. Thus, the domain structure of silk proteins needs to enable nanoscale phase separation to achieve high solubility of hydrophobic proteins in aqueous solutions. Additionally, silk proteins need to avoid premature precipitation as beta-sheets during storage and processing. Here we use mapping of domain types, sizes and distributions in silks to identify consistent design features that have evolved to meet these requirements. We show that silk proteins consist of conspicuously hydrophilic terminal domains flanking a very long central portion constructed from hydrophobic blocks separated by hydrophilic ones, discussing the domain structure in detail. The general rules of construction for silk proteins based on our observations should give a useful guide to the way in which Nature has solved the problem of processing hydrophobic proteins in water and how this can be copied industrially. Following these rules may also help in obtaining adequate expression, soluble products and controllable conformational switches in the production of genetically engineered or chemically synthesized silk analogues. Thus these insights have implications for structural biology and relevance to fundamental and applied questions in material science and engineering.     

Surface Hydrophobicity of Culture and Water Biofilm of <Emphasis Type="Italic">Penicillium</Emphasis> spp.

Fungal surface hydrophobicity is involved in several functions in fungal growth and development. Water contact angles measurement has been used as a direct and simple approach for its characterisation in solid cultures. Microsphere adhesion assay is said to be the best method to assess cell hydrophobicity of filamentous fungi. This study aimed to apply these two methods to study hydrophobicity of Penicillium expansum and Penicillium brevicompactum grown as mycelial mats in solid culture, liquid culture and water biofilms. As result, both species in solid cultures were classified as hydrophobic with contact angles ≥90o, but in liquid cultures and water biofilms showed different levels of hydrophobicity when microsphere adhesion assay was applied. In addition, was found that biofilms have specific hydrophobic hyphae which may be involved in fungal ecological functions.     

Characterization of product capture resin during microbial cultivations

Various bioactive small molecules produced by microbial cultivation are degraded in the culture broth or may repress the formation of additional product. The inclusion of hydrophobic adsorber resin beads to capture these products in situ and remove them from the culture broth can reduce or prevent this degradation and repression. These product capture beads are often subjected to a dynamic and stressful microenvironment for a long cultivation time, affecting their physical structure and performance. Impact and collision forces can result in the fracturing of these beads into smaller pieces, which are difficult to recover at the end of a cultivation run. Various contaminating compounds may also bind in a non-specific manner to these beads, reducing the binding capacity of the resin for the product of interest (fouling). This study characterizes resin bead binding capacity (to monitor bead fouling), and resin bead volume distributions (to monitor bead fracture) for an XAD-16 adsorber resin used to capture epothilone produced during myxobacterial cultivations. Resin fouling was found to reduce the product binding capacity of the adsorber resin by 25–50%. Additionally, the degree of resin bead fracture was found to be dependent on the cultivation length and the impeller rotation rate. Microbial cultivations and harvesting processes should be designed in such a way to minimize bead fragmentation and fouling during cultivation to maximize the amount of resin and associated product harvested at the end of a run.     

Reversed micelle solvents as tools of enzyme purification and enzyme-catalyzed conversion

Reversed micelle solvents represent nanometer-sized aqueous droplets stabilized by surfactants inside the bulk organic solvents. The aqueous cores can host various hydrophilic solutes, including bioactive substances thus revealing a challenge to the biotechnology's needs of the safe media for bioseparations and bioconversions. This review discusses the structure and the properties of reversed micelle solvents in view of the parameters that can be easily operated in technology to achieve safe liquid-liquid extraction of proteins/enzymes or bioconversion of hydrophobic substrates. The paper highlights the importance of how the reversed micelle microenvironment should be arranged with respect to the preservation of the activity of the enzyme as target product or biocatalyst. The main aspects are demonstrated with own experimental results on alpha-amylase purification and lipase-catalyzed esterification using cationic reversed micelle solvents. The trials of performing continuous processes involving reversed micellar separation and reaction media are also reviewed and the current problems are addressed.     

Some properties of the walls of metaxylem vessels of maize roots,including tests of the wettability of their lumenal wall surfaces

Background and Aims

Since the proposal of the cohesion theory there has been a paradox that the lumenal surface of vessels is rich in hydrophobic lignin, while tension in the rising sap requires adhesion to a hydrophilic surface. This study sought to characterize the strength of that adhesion in maize (Zea mays), the wettability of the vessel surface, and to reconcile this with its histochemical and physical nature.

Methods

Wettability was assessed by emptying the maize root vessels of sap, perfusing them with either water or oil, and examining the adhesion (as revealed by contact angles) of the two liquids to vessel walls by cryo-scanning electron microscopy. The phobicity of the lumenal surface was also assessed histochemically with hydrophilic and hydrophobic probes.

Key Results

Pit borders in the lumen-facing vessel wall surface were wetted by both sap/water and oil. The attraction for oil was weaker: water could replace oil but not vice versa. Pit apertures repelled oil and were strongly stained by hydrophilic probes. Pit chambers were probably hydrophilic. Oil never entered the pits. When vessels were emptied and cryo-fixed immediately, pit chambers facing away from the vessels were always sap-filled. Pit chambers facing vessel lumens were either sap- or gas-filled. Sap from adjoining tracheary elements entering empty vessels accumulated on the lumenal surface in hemispherical drops, which spread out with decreasing contact angles to fill the lumen.

Conclusions

The vessel lumenal surface has a dual nature, namely a mosaic of hydrophilic and hydrophobic patches at the micrometre scale, with hydrophilic predominating. A key role is shown, for the first time, of overarching borders of pits in determining the dual nature of the surface. In gas-filled (embolized) vessels they are hydrophobic. When wetted by sap (vessels refilling or full) they are hydrophilic. A hypothesis is proposed to explain the switch between the two states.     

RGD Surface Functionalization of the Hydrophilic Acrylic Intraocular Lens Material to Control Posterior Capsular Opacification

Posterior Capsular Opacification (PCO) is the capsule fibrosis developed on implanted IntraOcular Lens (IOL) by the de-differentiation of Lens Epithelial Cells (LECs) undergoing Epithelial Mesenchymal Transition (EMT). Literature has shown that the incidence of PCO is multifactorial including the patient''s age or disease, surgical technique, and IOL design and material. Reports comparing hydrophilic and hydrophobic acrylic IOLs have shown that the former has more severe PCO. On the other hand, we have previously demonstrated that the adhesion of LECs is favored on hydrophobic compared to hydrophilic materials. By combining these two facts and contemporary knowledge in PCO development via the EMT pathway, we propose a biomimetically inspired strategy to promote LEC adhesion without de-differentiation to reduce the risk of PCO development. By surface grafting of a cell adhesion molecule (RGD peptide) onto the conventional hydrophilic acrylic IOL material, the surface-functionalized IOL can be used to reconstitute a capsule-LEC-IOL sandwich structure, which has been considered to prevent PCO formation in literature. Our results show that the innovative biomaterial improves LEC adhesion, while also exhibiting similar optical (light transmittance, optical bench) and mechanical (haptic compression force, IOL injection force) properties compared to the starting material. In addition, compared to the hydrophobic IOL material, our bioactive biomaterial exhibits similar abilities in LEC adhesion, morphology maintenance, and EMT biomarker expression, which is the crucial pathway to induce PCO. The in vitro assays suggest that this biomaterial has the potential to reduce the risk factor of PCO development.     

Investigation on bioactive protection of the amino acids derived from LEA protein on insulin by molecular simulation

Nowadays heat-sensitive protein medicines are increasingly showing their importance in the treatment of various diseases. Their popularisation and application are meeting a great challenge because of their heat lability. In this study, human insulin as a heat-sensitive protein medicine and 66 amino acids derived from a Group 3 late embryogenesis abundant protein fragment as a complex bioactive protectant, were chosen to be investigated to determine whether these amino acids can be used to protect the insulin from denaturation due to drying. The experiments were carried out by using a replica exchange molecular dynamics (REMD) simulation and GROMACS software with Gromos96 (53a6) force field. The REMD results indicate that those amino acids can effectively prevent the reversal between hydrophilic and hydrophobic surface. Both the configurations and secondary structures of the protected insulin were preserved very well. The H-bonding and electrostatic interactions between the insulin and the protectant play key roles in the bioactive protection of insulin. These results agree well with the water replacement hypothesis. All the results prove that these amino acids are a perfect bioactive protectant for heat-sensitive protein medicines.     

Comparative studies of products obtained from solvolysis liquefaction of oil palm empty fruit bunch fibres using different solvents

Solvolysis of oil palm empty fruit bunches (EFB) fibres using different solvents (acetone, ethylene glycol (EG), ethanol, water and toluene) were carried out using an autoclave at 275°C for 60 min. The solvent efficiency in term of conversion yield was found to be: EG>water>ethanol>acetone>toluene. The liquid products and residue obtained were analyzed using Fourier transform infrared spectroscopy (FTIR) and gas chromatography/mass selectivity. The obtained results showed that the chemical properties of the oil product were significantly affected by the type of solvent used for the solvolysis process. The higher heating value (HHV) of oil products obtained using ethanol is ～29.42 MJ/kg, which is the highest among the oil products produced using different solvents. Water, ethanol and toluene yield major phenolic compounds. While EG favors the formation of alcohol compounds and acetone yields ketone and aldehyde compounds.     

Heterologous expression and characterization of the hydrophobin HFBI in Pichia pastoris and evaluation of its contribution to the food industry

The class II hydrophobin HFBI from Trichoderma reesei was heterologously expressed by Pichia pastoris using pPIC9 vector under the control of the promoter AOX1. The recombinant HFBI (rHFBI) was purified by ultrafiltration and reverse-phase high performance liquid chromatography. Tricine-SDS-PAGE and Western blotting demonstrated that rHFBI with the expected molecular weight of 7.5 kDa was secreted into the culture medium. X-ray photoelectron spectroscopy and water contact angle measurements indicated that rHFBI could lead to the conversion of the wettability of the hydrophobic siliconized glass and hydrophilic mica surfaces relying on the self-assembly membrane on hydrophobic/hydrophilic interfaces. It was demonstrated that rHFBI had the ability to stabilize oil droplets, which was far excess of the class I hydrophobin HGFI heterologously expressed in P. pastoris (rHGFI) and the typical food emulsifier sodium caseinate. In gushing experiments, it was shown that rHFBI was a strong gushing inducer in beer, whereas rHGFI did not display any signs of gushing. This provided the potential of rHFBI to be used as a novel emulsifying agent and a predictor of gushing risk.     

Adhesion of the Entomopathogenic Fungus Beauveria (Cordyceps) bassiana to Substrata

The entomopathogenic fungus Beauveria bassiana produces at least three distinct single-cell propagules, aerial conidia, vegetative cells termed blastospores, and submerged conidia, which can be isolated from agar plates, from rich broth liquid cultures, and under nutrient limitation conditions in submerged cultures, respectively. Fluorescently labeled fungal cells were used to quantify the kinetics of adhesion of these cell types to surfaces having various hydrophobic or hydrophilic properties. Aerial conidia adhered poorly to weakly polar surfaces and rapidly to both hydrophobic and hydrophilic surfaces but could be readily washed off the latter surfaces. In contrast, blastospores bound poorly to hydrophobic surfaces, forming small aggregates, bound rapidly to hydrophilic surfaces, and required a longer incubation time to bind to weakly polar surfaces than to hydrophilic surfaces. Submerged conidia displayed the broadest binding specificity, adhering to hydrophobic, weakly polar, and hydrophilic surfaces. The adhesion of the B. bassiana cell types also differed in sensitivity to glycosidase and protease treatments, pH, and addition of various carbohydrate competitors and detergents. The outer cell wall layer of aerial conidia contained sodium dodecyl sulfate-insoluble, trifluoroacetic acid-soluble proteins (presumably hydrophobins) that were not present on either blastospores or submerged conidia. The variations in the cell surface properties leading to the different adhesion qualities of B. bassiana aerial conidia, blastospores, and submerged conidia could lead to rational design decisions for improving the efficacy and possibly the specificity of entomopathogenic fungi for host targets.     

Local hydrophobicity stabilizes secondary structures in proteins

The probability of occurrence of helix and β-sheet residues in 47 globular proteins was determined as a function of local hydrophobicity, which was defined by the sum of the Nozaki-Tanford transfer free energies at two nearest-neighbors on both sides of the amino acid sequence. In general, hydrophilic amino acids favor neither helix nor β-sheet formations when neighbor residues are also hydrophilic but favor helix formation at higher local hydrophobicity. On the other hand, some hydrophobic amino acids such as Met, Leu, and Ile favor helix formation when neighbor residues are hydrophilic. None of the hydrophobic amino acids favor β-sheet formation with hydrophilic neighbors, but most of them strongly favor β-sheet formation at high local hydrophobicity. When the average of 20 amino acids is taken, both helix and β-sheet residue probabilities are higher at higher local hydrophobicity, although the increase is steeper for β-sheets. Therefore, β-sheet formation is more influenced by local hydrophobicity than helix formation. Generally, helices are nearer the surface and tend to have hydrophilic and hydrophobic faces at opposite sides. The tendency of alternating regions of hydrophilic and hydrophobic residues in a helical sequence was revealed by calculating the correlation of the Nozaki-Tanford values. Such amphipathic helices may be important in protein–protein and protein–lipid interactions and in forming hydrophilic channels in the membrane. The choice of 30 nonhomologous proteins as the data set did not alter the above results.     

Potential of plant cells in culture for cosmetic application

Plants and plant derived ingredients are common and of major importance in the fields of pharmacy, food and cosmetics. The cosmetic industry is a fast moving market. Products have short life-cycles and the industry has to come up with innovative products constantly. Most cosmetic products and their applications are defined by active ingredients. These active ingredients may derive from either synthetic sources or from plant sources. Beside this, no other origin like human or animal are accepted or allowed in cosmetics nor are genetically modified plant sources. The whole cosmetic research and development society is therefore desperately seeking for new innovative plant ingredients for cosmetic application. Unfortunately, new plant derived ingredients are limited because several plants of cosmetic interest are not to be used due to following facts: the plants contain toxic metabolites, the plants grow too slow and a seasonal harvesting is not possible, the concentration of plant constituents differ from harvest to harvest or the plant is endangered and not allowed to harvest. With the plant cell culture technology we bring complete new aspects in the development of novel cosmetic plant derived actives. Due to all these findings, we decided to risk the step into plant cell culture derived cosmetic active ingredient production. This article describes the successful establishment of an apple suspension culture producing a high yield of biomass, cultured in disposable, middle-scale bioreactors. The use of a bioactive extract out of these cells for cosmetic application and the efficacy of this extract on mammalian stem cells is also outlined in this article. To obtain a suitable cosmetic product we used the high pressure homogenization technique to decompose the plant cells and release all the beneficial constituents while encapsulating these components at the same time in liquid Nanoparticles. With the plant cell culture technology we bring complete new aspects in the development of novel cosmetic plants derived actives.     

Fabricating PLGA microparticles with high loads of the small molecule antioxidant N‐acetylcysteine that rescue oligodendrocyte progenitor cells from oxidative stress

Reactive oxygen species (ROS), encompassing all oxygen radical or non‐radical oxidizing agents, play key roles in disease progression. Controlled delivery of antioxidants is therapeutically relevant in such oxidant‐stressed environments. Encapsulating small hydrophilic molecules into hydrophobic polymer microparticles via traditional emulsion methods has long been a challenge due to rapid mass transport of small molecules out of particle pores. We have developed a simple alteration to the existing water‐in‐oil‐in‐water (W/O/W) drug encapsulation method that dramatically improves loading efficiency: doping external water phases with drug to mitigate drug diffusion out of the particle during fabrication. PLGA microparticles with diameters ranging from 0.6 to 0.9 micrometers were fabricated, encapsulating high loads of 0.6–0.9 µm diameter PLGA microparticles were fabricated, encapsulating high loads of the antioxidant N‐acetylcysteine (NAC), and released active, ROS‐scavenging NAC for up to 5 weeks. Encapsulation efficiencies, normalized to the theoretical load of traditional encapsulation without doping, ranged from 96% to 400%, indicating that NAC‐loaded external water phases not only prevented drug loss due to diffusion, but also doped the particles with additional drug. Antioxidant‐doped particles positively affected the metabolism of oligodendrocyte progenitor cells (OPCs) under H₂O₂‐mediated oxidative stress when administered both before (protection) or after (rescue) injury. Antioxidant doped particles improved outcomes of OPCs experiencing multiple doses of H₂O₂ by increasing the intracellular glutathione content and preserving cellular viability relative to the injury control. Furthermore, antioxidant‐doped particles preserve cell number, number of process extensions, cytoskeletal morphology, and nuclear size of H₂O₂‐stressed OPCs relative to the injury control. These NAC‐doped particles have the potential to provide temporally‐controlled antioxidant therapy in neurodegenerative disorders such as multiple sclerosis (MS) that are characterized by continuous oxidative stress.     

Responses of Marine Bacteria Under Starvation Conditions at a Solid-Water Interface

Size changes during starvation of 17 marine bacterial isolates at a solid-water interface and in the liquid phase were examined. Twelve rod-shaped, hydrophilic bacteria decreased in size more rapidly at the solid surface than in the liquid phase, a result parallel to that observed previously for one of the strains at an air-water interface. On the other hand, three rod-shaped, hydrophobic bacteria diminished in size more rapidly in the liquid phase than at the solid-water interface. The rapid size decrease (defined here as the dwarfing phase) in either situation appeared to be an active process which occurred more rapidly when the cells were in an early stage of logarithmic growth at the onset of starvation. Dwarfing was reversibly inhibited by low temperature and low pH but was not inhibited by chloramphenicol. Three coccoidal bacteria showed little tendency to become smaller upon starvation in the liquid phase or at a surface.     

A Nitrite Microsensor for Profiling Environmental Biofilms

A highly selective liquid membrane nitrite microsensor based on the hydrophobic ion-carrier aquocyanocobalt(III)-hepta(2-phenylethyl)-cobrynate is described. The sensor has a tip diameter of 10 to 15 (mu)m. The response is log-linear in freshwater down to 1 (mu)M NO(inf2)(sup-) and in seawater to 10 (mu)M NO(inf2)(sup-). A method is described for preparation of relatively large polyvinyl chloride (PVC)-gelled liquid membrane microsensors with a tip diameter of 5 to 15 (mu)m, having a hydrophilic coating on the tip. The coating and increased tip diameter resulted in more sturdy sensors, with a lower detection limit and a more stable signal than uncoated nitrite sensors with a tip diameter of 1 to 3 (mu)m. The coating protects the sensor membrane from detrimental direct contact with biomass and can be used for all PVC-gelled liquid membrane sensors meant for profiling microbial mats, biofilms, and sediments. Thanks to these improvements, liquid membrane sensors can now be used in complex environmental samples and in situ, e.g., in operating bioreactors. Examples of measurements in denitrifying, nitrifying, and nitrifying/denitrifying biofilms from wastewater treatment plants are shown. In all of these biofilms high nitrite concentrations were found in narrow zones of less than 1 mm.     

Adhesion of the entomopathogenic fungus Beauveria (Cordyceps) bassiana to substrata

The entomopathogenic fungus Beauveria bassiana produces at least three distinct single-cell propagules, aerial conidia, vegetative cells termed blastospores, and submerged conidia, which can be isolated from agar plates, from rich broth liquid cultures, and under nutrient limitation conditions in submerged cultures, respectively. Fluorescently labeled fungal cells were used to quantify the kinetics of adhesion of these cell types to surfaces having various hydrophobic or hydrophilic properties. Aerial conidia adhered poorly to weakly polar surfaces and rapidly to both hydrophobic and hydrophilic surfaces but could be readily washed off the latter surfaces. In contrast, blastospores bound poorly to hydrophobic surfaces, forming small aggregates, bound rapidly to hydrophilic surfaces, and required a longer incubation time to bind to weakly polar surfaces than to hydrophilic surfaces. Submerged conidia displayed the broadest binding specificity, adhering to hydrophobic, weakly polar, and hydrophilic surfaces. The adhesion of the B. bassiana cell types also differed in sensitivity to glycosidase and protease treatments, pH, and addition of various carbohydrate competitors and detergents. The outer cell wall layer of aerial conidia contained sodium dodecyl sulfate-insoluble, trifluoroacetic acid-soluble proteins (presumably hydrophobins) that were not present on either blastospores or submerged conidia. The variations in the cell surface properties leading to the different adhesion qualities of B. bassiana aerial conidia, blastospores, and submerged conidia could lead to rational design decisions for improving the efficacy and possibly the specificity of entomopathogenic fungi for host targets.