Biosorption of uranium and thorium

Selected samples of waste microbial biomass originating from various industrial fermentation processes and biological treatment plants have been screened for biosorbent properties in conjunction with uranium and thorium in aqueous solutions. Biosorption isotherms have been used for the evaluation of biosorptive uptake capacity of the biomass which was also compared to an activated carbon and the ion exchange resin currently used in uranium production processes. Determined uranium and thorium biosorption isotherms were independent of the initial U or Th solution concentration. Solution pH affected the exhibited uptake. In general, lower biosorptive uptake was exhibited at pH 2 than at pH 4. No discernible difference in uptake was observed between pH 4 and pH 5 where the optimum pH for biosorption lies. The biomass of Rhizopus arrhizus at pH 4 exhibited the highest uranium and thorium biosorptive uptake capacity (g) in excess of 180 mg/g. At an equilibrium uranium concentration of 30 mg/liter, R. arrhizus removed approximately 2.5 and 3.3 times more uranium than the ion exchange resin and activated carbon, respectively. Under the same conditions, R. arrhizus removed 20 times more thorium than the ion exchange resin and 2.3 times more than the activated carbon. R. arrhizus also exhibited higher uptake and a generally more favorable isotherm for both uranium and thorium than all other biomass types examined.     

Biosorption of uranium by Myxococcus xanthus

This paper deals with uranium biosorption by Myxococcus xanthus biomass in which dry biomass, accumulating up to 2.4 mM of uranium g⁻¹, is demonstrated to be a more efficient biosorbent than wet biomass. For uranium concentrations of 0.1–0.3 mM, between 95.79% and 95.99% of the uranium was taken up from the solution. Dry biomass biosorption was found to be relatively rapid, reaching equilibrium after 5–10 min. In addition, the pH influenced biosorption, pH 4.5 promoting maximum uptake. It was also established that the biosorbed uranium is located on the cellular wall and within the extracellular mucopolysaccharide of this microorganism. Furthermore, using sodium carbonate as a desorbent agent, 80.82% of the biosorbed uranium could be recovered. The results obtained indicate the possible utilization of M. xanthus biomass to solve some problems of the water contaminated by uranium.     

The use of flocculating brewer's yeast for Cr(III) and Pb(II) removal from residual wastewaters

The use of inexpensive biosorbents to sequester heavy metals from aqueous solutions, is one of the most promising technologies being developed to remove these toxic contaminants from wastewaters. Considering this challenge, the viability of Cr(III) and Pb(II) removal from aqueous solutions using a flocculating brewer's yeast residual biomass from a Portuguese brewing industry was studied. The influence of physicochemical factors such as medium pH, biomass concentration and the presence of a co-ion was characterised. Metal uptake kinetics and equilibrium were also analysed, considering different incubation temperatures. For both metals, uptake increased with medium pH, being maximal at 5.0. Optimal biomass concentration for the biosorption process was determined to be 4.5?g dry weight/l. In chromium and lead mixture solutions, competition for yeast binding sites was observed between the two metals, this competition being pH dependent. Yeast biomass showed higher selectivity and uptake capacity to lead. Chromium uptake kinetic was characterised as having a rapid initial step, followed by a slower one. Langmuir model describes well chromium uptake equilibrium. Lead uptake kinetics suggested the presence of mechanisms other than biosorption, possibly including its precipitation.     

The role of chitin in uranium adsorption by R. arrhizus

In order to further refine and support the uranium biosorption mechanism hypothesis proposed for Rhizopus arrhizus, uranium competitive equilibrium uptake isotherms by chitin were determined at two different solution pH levels and in the presence of different concentrations of competing ions, namely, Cu(2+), Zn(2+), and Fe(2+). The co-ion effect became more poronounced as the co-ion concentration in solution and pH increased. Obtained equilibrium data are in agreement with uranium biosorption data reported earlier. Infrared, mass, and electron paramagnetic resonance (EPR) spectra of chitin before and after uranium uptake in the presence of the competing ions Cu(2+), Zn(2+), and Fe(2+) were recorded. The combination of the spectral data and the information from equilibrium studies supported the hypothesis advanced earlier on the mechanism of uranium uptake by R.arrhizus. In addition, the data suggested the participation of a free radical in uranium coordination by the cell wall chitin. The mechanism of reduction of the uranium uptake capacity of the biomass in the presence of competing ions was also elucidated further.     

Biosorption Potentiality of Living Aspergillus niger Tiegh in Removing Heavy Metal from Aqueous Solution

The species of Aspergillus niger Tiegh isolated from estuarine sediments has been studied for tolerance to heavy metals such as Hg and Pb and for its capacities to uptake metals. A. niger was allowed to grow in monometal- as well as bimetal-containing media (25 mg L^?1) to determine the biosorption capacity of the organism. The effects of temperature and pH on biosorption were studied to elucidate the biosorption property and optimum growth conditions for the organism. Results revealed that 91.1% of Pb and 97.1% of Hg were removed from the monometal solutions, and there was a reduction of 96.9% of Hg and 89.3% of Pb from the bimetal solution after 92 h of fungal growth. The binding mechanism involved between metal ion and functional groups present on the cell surface of the biomass was studied using Fourier transform infrared (FTIR), which confirms the presence of amine, hydroxyl, carboxyl, and phosphate groups. The adsorption of metal ions on the biomass surface was confirmed using scanning electron microscopy–energy dispersive x-ray (SEM-EDAX) studies. The experimental study proved that A. Niger can be used as a suitable biosorption agent for removing metal ions when present in low concentration.     

Biosorption of heavy metals by Saccharomyces cerevisiae: a review

Heavy metal pollution has become one of the most serious environmental problems today. Biosorption, using biomaterials such as bacteria, fungi, yeast and algae, is regarded as a cost-effective biotechnology for the treatment of high volume and low concentration complex wastewaters containing heavy metal(s) in the order of 1 to 100 mg/L. Among the promising biosorbents for heavy metal removal which have been researched during the past decades, Saccharomyces cerevisiae has received increasing attention due to the unique nature in spite of its mediocre capacity for metal uptake compared with other fungi. S. cerevisiae is widely used in food and beverage production, is easily cultivated using cheap media, is also a by-product in large quantity as a waste of the fermentation industry, and is easily manipulated at molecular level. The state of the art in the field of biosorption of heavy metals by S. cerevisiae not only in China, but also worldwide, is reviewed in this paper, based on a substantial number of relevant references published recently on the background of biosorption achievements and development. Characteristics of S. cerevisiae in heavy metal biosorption are extensively discussed. The yeast can be studied in various forms for different purposes. Metal-binding capacity for various heavy metals by S. cerevisiae under different conditions is compared. Lead and uranium, for instances, could be removed from dilute solutions more effectively in comparison with other metals. The yeast biosorption largely depends on parameters such as pH, the ratio of the initial metal ion and initial biomass concentration, culture conditions, presence of various ligands and competitive metal ions in solution and to a limited extent on temperature. An assessment of the isotherm equilibrium model, as well as kinetics was performed. The mechanisms of biosorption are understood only to a limited extent. Elucidation of the mechanism of metal uptake is a real challenge in the field of biosorption. Various mechanism assumptions of metal uptake by S. cerevisiae are summarized.     

An ecofriendly approach for bioremediation of contaminated water environment: Potential contribution of a coastal seaweed community to environmental improvement

High levels of heavy metals like copper ions in many industrial based effluents lead to serious environmental and health problems. Biosorption is a potential environmental biotechnology approach for biotreatment of aquatic sites polluted with heavy metal ions. Seaweeds have received great attention for their high bioremediation potential in recent years. However, the co-application of marine macroalgae for removal of heavy metals from wastewater is very limited. Thus, for the first time in literature, a coastal seaweed community composed of Chaetomorpha sp., Polysiphonia sp., Ulva sp. and Cystoseira sp. species was applied to remove copper ions from synthetic aqueous medium in this study. The biosorption experiments in batch mode were conducted to examine the effects of operating variables including pH, biosorbent amount, metal ion concentration and contact time on the biosorption process. The biosorption behavior of biosorbent was described by various equilibrium, kinetic and thermodynamic models. The biosorption of copper ions was strongly influenced by the operating parameters. The results indicated that the equilibrium data of biosorption were best modeled by Sips isotherm model. The values of mean free energy of biosorption computed from Dubinin-Radushkevich isotherm model and the standard Gibbs free energy change indicated a feasible, spontaneous and physical biotreatment system. The pseudo-second-order rate equation successfully defined the kinetic behavior of copper biosorption. The pore diffusion also played role in the control of biosorption process. The maximum copper uptake capacity of biosorbent was found to be greater than those of many other biosorbents. The obtained results revealed that this novel biosorbent could be a promising material for copper ion bioremediation implementations.     

Biosorption behavior of heavy metals in bioleaching process of MSWI fly ash by Aspergillus niger

In this study, it was considered that the biosorption of heavy metals by biomass might occur during the bioleaching of fly ash. This work is focused on the biosorption behavior of Al, Fe, Pb and Zn by Aspergillus niger during the bioleaching process. The fungal biomass was contacted with heavy metals solution which extracted from fly ash by using gluconic acid as leaching agent. The equilibrium time for biosorption was about 120 min. The biosorption experiment data at initial pH 6.5 was used to fit the biosorption kinetics and isotherm models. The results indicated that the biosorption of Al, Fe and Zn by A. niger biomass were well described by the pseudo-first order kinetic model. The pseudo-second order kinetic model was more suitable for that of Pb. The Langmuir isotherm model could well describe the biosorption of Fe, Pb and Zn while the Freundlich model could well describe the biosorption of Al. Furthermore, the biosorption of metal ions decreased evidently in the presence of fly ash as compared to that in the absence of fly ash. This research showed that although the biomass sorption occurred during the bioleaching process, it did not inhibit the removal of Al, Fe, Pb and Zn evidently from fly ash.     

Studies on the biosorption of uranium by a thermotolerant, ethanol-producing strain of Kluyveromyces marxianus

The ability of residual biomass from the thermotolerant ethanol-producing yeast strain Kluyveromyces marxianus IMB3 to function as a biosorbent for uranium has been examined. It was found that the biomass had an observed maximum biosorption capacity of 120?mg U/g dry weight of biomass. The calculated value for the biosorption maximum, obtained by fitting the data to the Langmuir model was found to be 130?mg U/g dry weight biomass. Maximum biosorption capacities were examined at a number of temperatures and both the observed and calculated values obtained for those capacities increased with increasing temperature. Decreasing the pH of the biosorbate solution resulted in a decrease in uptake capacity. When biosorption reactions were carried out using sea-water as the diluent it was found that the maximum biosorption capacity of the biomass increased significantly. Using transmission electron microscopy, uranium crystals were shown to be concentrated on the outer surface of the cell wall, although uranium deposition was also observed in the interior of the cell.     

The effect of pulse field strength on electric field stimulated biosorption of uranium by Kluyveromyces marxianus IMB3

Summary Improved biosorption of uranium by Kluyveromyces marxianus IMB3 biomass was achieved by increasing the electric field strength of delivered pulses from 1.25kV/cm to 2.5kV/cm. Although this had little or no effect on the maximum biosorption capacity (q_max), at low concentrations of uranium the amount bound to the biomass increased from 70 to 140mg uranium/g biomass. Significant increases in the maximum biosorption capacities (119–180 mg uranium/g biomass) were observed when the pulse field strength was increased from 2.5kV/cm to 3.25kV/cm.     

Effects of selected physical and chemical parameters on uranium uptake by the bacterium Chryseomonas MGF-48

The effect of selected physical and chemical parameters, including media composition, uranium concentration, and metabolic inhibitors, on uranium uptake from aqueous solution by Chryseomonas sp. MGF-48, a bacterium isolated from electroplating effluent, was analysed. It was found that 198 mg/g (dry weight) of uranium was taken up from a 150 ppm (mg/l) solution of uranium when cells were maintained under starvation conditions. Uranium was released from the cells by addition of sodium carbonate. Uptake of uranium was reduced when cells were subjected to pretreatment with ultraviolet (u.v.) light (263.7 nm, 10 min) or heat (100 °C, 15 min), i.e., 99.8 and 57.5 mg/g, respectively. Addition of 2, 4-dinitrophenol (10 mM) or sodium azide (0.1%) resulted in decreased uptake (129 and 123 mg/g, respectively), whereas addition of glycerol-2-phosphate (G-2-P) resulted in deposition of uranium. Maximum uptake of uranium occurred at pH 6.5. Uranium uptake in the presence of selected carbohydrates decreased as follows: xylose > arabinose > mannose > maltose > glucose. When Chryseomonas sp. MGF-48 was exposed to 5, 50, or 100 mg/l uranium prior to uptake experiments, a decrease in uranium uptake was noted. Furthermore, immobilization of the bacterial cells in a calcium-alginate medium reduced the efficiency of uptake, yielding only 60% uranium uptake. It is concluded that uranium uptake and accumulation by this bacterium involves both metabolism-independent absorption and metabolism-dependent absorption, the former being considered to be more efficient.     

The effect of electric field stimulation on the biosorption of uranium by non-living biomass derived from Kluyveromyces marxianus IMB3

Summary Non-living biomass from the thermotolerant, ethanol-producing yeast strain Kluyveromyces marxianus IMB3 is capable of uranium biosorption. The biomass has an observed biosorption capacity of 115mg uranium/g dry weight of biomass with a calculated value of 127mg uranium/g dry weight. Following exposure of the biomass to electric fields of 2,500 V/cm for 20msec. the maximum biosorption capacity (observed or calculated) for uranium did not differ significantly for the untreated biomass. However, at lower residual concentrations of uranium (<10mg/L) the capacity of the treated biomass for uranium was significantly increased above values obtained with untreated material.     

The effect of pulse voltage and capacitance on biosorption of uranium by biomass derived from whiskey distillery spent wash

Biosorption of uranium by residual biomass from The Old Bushmill's Distillery Co. Ltd., Bushmills, Co. Antrim, Northern Ireland, following exposure to short and intense electric pulses has been examined. The biomass was prepared from the distillery spent wash and consisted of non-viable yeast and bacterial cells. As shown previously, untreated biomass had a maximum biosorption capacity of 170?mg uranium/g dry weight biomass. When biosorption reactions were placed between two electrodes and exposed to electric pulses with field strengths ranging from 1.25–3.25?kV/cm at a capacitance of 25?μF, biosorption increased from 170?mg of uranium to 275?mg uranium/g dry weight biomass. The data were obtained from biosorption isotherm analyses and taken as the degree of biosorption at residual uranium concentrations of 3?mM. In addition, when the capacitance of the electric pulses increased from 0.25?μF to 25?μF at a fixed pulse field strength the degree of biosorption increased from 210?mg uranium to 240?mg uranium/g dry weight biomass. The results suggest that application of short and intense electric pulses to biosorption reactions may play an important role in enhancing microbial biosorption of toxic metals/radionuclides from waste water streams.     

Biosorption of tributyltin and other organotin compounds by cyanobacteria and microalgae

Biosorption of triorganotin compounds by the cyanobacteria Synechocystis PCC 6803 and Plectonema boryanum and the microalga Chlorella emersonii, incubated in 2-(N-morpholino)ethanesulphonic acid (MES) buffer, pH 5.5, in the presence of 0.5 mm organotin (supplied as chlorides), increased with molecular mass of the organotins, the order being triphenyltin > tributylin (Bu₃SnCl) > tripropyltin >- trimethyltin >- triethylin. In the butylin series, monobutyltin biosorption was lowest, although levels of dibutyltin uptake were greater than for Bu₃SnCl. Cyanobacterial Bu₃SnCl biosorption was complete in 5 min with no subsequent accumulation. In contrast, a second phase of uptake in C. emersonii resulted in an approximate 2.4-fold increase in cellular Bu₃SnCl between 5 min and 2 h. The external pH had a marked influence on biosorption of Bu₃SnCl by Synechocystis PCC 6803 and P. boryanum, with maximal uptake at pH 5.5 and 6.5, respectively. Effects of pH were less evident in C. emersonii. In all the organisms examined, no inhibition of Bu₃SnCl biosorption was observed between 0.05 and 50 mm NaCl. However, an increase in the external NaCl concentration from 50 to 500 mm resulted in an approximate 55–65% reduction in Bu₃SnCl uptake. Biosorption increased at increasing Bu₃SnCl concentrations (0.25–3.0 mm). Saturation of Bu₃SnCl biosorption at the higher concentrations was most evident in the cyanobacteria, although uptake levels were greater in these organisms at <- 2 mm Bu₃SnCl. Theoretical maximum biosorption levels at complete cell saturation, derived from reciprocal Langmuir plots, were approximately 565, 525 and 1050 nmol Bu₃SnCl mg^–1 dry weight, for Synechocystis PCC 6803, P. boryanum and C. emersonii, respectively. Correspondence to: G. M. Gadd     

Biotechnological potential of Microcystis sp. in Cu, Zn and Cd biosorption from single and multimetallic systems

This paper provides information on biosorption of Cu, Zn and Cd by Microcystis sp. in single, bi and trimetallic combination. Highest biosorption of Cu followed by Zn and Cd in single as well as in mixtures containing two or three metals was noticed. The order of inhibition of Cu, Zn and Cd biosorption in bi and trimetallic combinations was suggestive of screening or competition for the binding sites on the cell surface. This observation was reconfirmed by Freundlich adsorption isotherm. K_f values were maximum for Cu (K_f=45.18), followed by Zn (K_f=16.71), and Cd (K_f=15.63) in single metallic system. The K_f values for each test metal was reduced in solution containing more than one metal. Further, the reduction in biosorption of each metal ion due to presence of other metal ion was of greater magnitude at relatively higher concentrations of interfering metal ion. The biosorption of Cu at saturation was less affected when secondary metal (Cd or Zn) was added in the medium. Above results suggest that Microcystis holds great potential for metal biosorption from mixture.     

Metals sorption from aqueous solutions by Kluyveromyces marxianus: Process optimization,equilibrium modeling and chemical characterization

The dead Kluyveromyces marxianus biomass, a fermentation industry waste, was used to explore its sorption potential for lead, mercury, arsenic, cobalt, and cadmium as a function of pH, biosorbent dosage, contact time, agitation speed, and initial metal concentration. The equilibrium data fitted the Langmuir model better for cobalt and cadmium, but Freundlich isotherm for all metals tested. At equilibrium, the maximum uptake capacity (Qmax) was highest for lead followed by mercury, arsenic, cobalt, and cadmium. The RL values ranged between 0–1, indicating favorable sorption of all test metals by the biosorbent. The maximum Kf value of Pb showed its efficient removal from the solution. However, multi-metal analysis depicted that sorption of all metals decreased except Pb. The potentiometric titration of biosorbent revealed the presence of functional groups viz. amines, carboxylic acids, phosphates, and sulfhydryl group involved in heavy metal sorption. The extent of contribution of functional groups and lipids to biosorption was in the order: carboxylic>lipids>amines>phosphates. Blocking of sulfhydryl group did not have any significant effect on metal sorption.     

The mechanism of thorium biosorption by Rhizopus arrhizus

Inactive cells of Rhizopus arrhizus have been documented to exhibit a high thorium biosorptive uptake (170 mg/g) from aqueous solutions. The mechanism of thorium sequestering by this biomass type was investigated following the same method as for the uranium biosorption mechanism. The thorium sequestering mechanism appeared somewhat different from that of uranium. Experimental evidence is presented which indicates that, at optimum biosorption pH (4), thorium coordinates with the nitrogen of the chitin cell wall network and, in addition, more thorium is absorbed by the external section of the fungal cell wall. At pH 2 the overall thorium uptake is reduced. The kinetic study of thorium biosorption revealed a very rapid rate of uptake. Unlike uranium at optimum solution pH, Fe(2+) and Zn(2+) did not interfere significantly with the thorium biosorptive uptake capacity of R. arrhizus.     

Potential of Live Spirulina platensis on Biosorption of Hexavalent Chromium and Its Conversion to Trivalent Chromium

Microalga biomass has been described worldwide according their capacity to realize biosorption of toxic metals. Chromium is one of the most toxic metals that could contaminate superficial and underground water. Considering the importance of Spirulina biomass in production of supplements for humans and for animal feed we assessed the biosorption of hexavalent chromium by living Spirulina platensis and its capacity to convert hexavalent chromium to trivalent chromium, less toxic, through its metabolism during growth. The active biomass was grown in Zarrouk medium diluted to 50% with distilled water, keeping the experiments under controlled conditions of aeration, temperature of 30°C and lighting of 1,800 lux. Hexavalent chromium was added using a potassium dichromate solution in fed-batch mode with the aim of evaluate the effect of several additions contaminant in the kinetic parameters of the culture. Cell growth was affected by the presence of chromium added at the beginning of cultures, and the best growth rates were obtained at lower metal concentrations in the medium. The biomass removed until 65.2% of hexavalent chromium added to the media, being 90.4% converted into trivalent chromium in the media and 9.6% retained in the biomass as trivalent chromium (0.931 mg.g^?1).     

Biosorption of Chromium(VI) and Lead(II): Role of Spirulina platensis in the Treatment of Industrial Effluent

Biosorption is the process of removal of any chemical molecules by the treatment of biological material. Industrialization resulted in the discharge of various toxic heavy metals into water bodies, which poses serious health hazards to humans and animals. In the present study, live Spirulina platensis was used as a biosorbent for the removal of the heavy metals chromium (Cr(VI)) and lead (Pb(II)) from the aqueous samples. S. platensis were cultured in the presence of different concentrations of heavy metals. The growth of the algal cells was found to be decreased by 59% and 36% in media containing 50 ppm Cr(VI) and Pb(II), respectively. To assess the biosorption of heavy metals, at different time intervals, the spent culture media were used to detect Cr(VI) by atomic absorption spectroscopy method and Pb(II) by 4-(2-pyridylazo)resorcinol indicator method. Results suggested that there was a significant uptake of Cr(VI) and Pb(II) from the medium by S. platensis, with corresponding decrease of metals in the medium. When metal salt solutions or industrial effluent samples were passed through the column containing immobilized live S. platensis in calcium alginate beads, the concentration of Cr(VI) was found to be reduced drastically. The present study indicates the application of S. platensis for the bioremediation of heavy metals from the samples obtained from industrial effluents.     

Studies on the biosorption of uranium by Talaromyces emersonii CBS 814.70 biomass

Residual biomass, produced by the thermophilic fungus, Talaromyces emersonii CBS 814.70, following growth on glucose-containing media, was examined for its ability to take up uranium from aqueous solution. It was found that the biomass had a relatively high observed biosorption capacity for the uranium (280 mg/g dry weight biomass). The calculated maximum biosorption capacity obtained by fitting the data to a Langmuir model was calculated to be 323 mg uranium/g dry weight biomass. Pretreatment of the biomass with either dilute HCl or NaOH brought about a significant decrease in biosorptive capacity for uranium. Studies on the effects of variation in temperature on the biosorptive capacity demonstrated no significant change in binding between 20°C and 60°C. However, a significant decrease in biosorptive capacity was observed at 5°C. Binding of uranium to the biomass at all temperatures reached equilibrium within 2 min. While the routine binding assays were performed at pH 5.0, adjustment of the pH to 3.0 gave rise to a significant decrease in biosorption capacity by the biomass. The biosorptive capacity of the biomass for uranium was increased when extraction from solution in sea-water was examined.