Production of <Emphasis Type="SmallCaps">l</Emphasis>-phenylalanine from glycerol by a recombinant <Emphasis Type="Italic">Escherichia coli</Emphasis>

The production of l-phenylalanine is conventionally carried out by fermentations that use glucose or sucrose as the carbon source. This work reports on the use of glycerol as an inexpensive and abundant sole carbon source for producing l-phenylalanine using the genetically modified bacterium Escherichia coli BL21(DE3). Fermentations were carried out at 37°C, pH 7.4, using a defined medium in a stirred tank bioreactor at various intensities of impeller agitation speeds (300–500 rpm corresponding to 0.97–1.62 m s⁻¹ impeller tip speed) and aeration rates (2–8 L min⁻¹, or 1–4 vvm). This highly aerobic fermentation required a good supply of oxygen, but intense agitation (impeller tip speed ~1.62 m s⁻¹) reduced the biomass and l-phenylalanine productivity, possibly because of shear sensitivity of the recombinant bacterium. Production of l-phenylalanine was apparently strongly associated with growth. Under the best operating conditions (1.30 m s⁻¹ impeller tip speed, 4 vvm aeration rate), the yield of l-phenylalanine on glycerol was 0.58 g g⁻¹, or more than twice the best yield attainable on sucrose (0.25 g g⁻¹). In the best case, the peak concentration of l-phenylalanine was 5.6 g L⁻¹, or comparable to values attained in batch fermentations that use glucose or sucrose. The use of glycerol for the commercial production of l-phenylalanine with E. coli BL21(DE3) has the potential to substantially reduce the cost of production compared to sucrose- and glucose-based fermentations.     

Enhanced shear protection and increased production of an anti-tumor polysaccharide by Agaricus blazei in xanthan-supplemented cultures

Xanthan supplementation provided shear protection and stimulated polysaccharide production by Agaricus blazei. In xanthan-free cultures, the optimal cell yield, 0.63 g biomass g^–1 glucose, and product yield, 0.19 g polysaccharide g^–1 glucose, were, respectively, when the critical impeller tip speed was 50.3 cm s^–1 and 100.5 cm s^–1. Furthermore, the critical impeller tip speed of cell yield shifted from 50.3 cm s^–1 to 100.5 cm s^–1 with the supplementation of 1 g xanthan l^–1. Maximum specific product yield, namely 0.74 g polysaccharide g^–1 biomass, was achieved with inlet air supply of 3% O₂ and impeller tip speed of 100.5 cm s^–1.     

Early development of germlings of <Emphasis Type="Italic">Sargassum thunbergii</Emphasis> (Fucales,Phaeophyta) under laboratory conditions

Morphology and culture studies on germlings of Sargassum thunbergii (Mertens et Roth) Kuntze were carried out under controlled laboratory conditions. Growth characteristics of these germlings grown under different temperatures (from 10 to 25°C), irradiances (from 9 to 88 μmol photons m⁻² s⁻¹), and under blue and white light conditions are described. The development of embryonic germlings follows the classic “8 nuclei 1 egg” type described for Sargassaceae. Fertilized eggs spent 5–6 h developing into multicellular germlings with abundant rhizoids after fertilization. Under conditions of 20°C, 44 μmol photons m⁻² s⁻¹ and photoperiod of 12 h, young germlings with one or two leaflets reached 2–3 mm in length after 8 weeks. Temperature variations (10, 15, 20, 25°C) under 88 μmol photons m⁻² s⁻¹ significantly influenced the growth rate within the first week, although this effect became less obvious after 8 weeks, especially at 15 and 20°C. Variation in germling growth was highly significant under different irradiances (9, 18, 44, 88 μmol photons m⁻² s⁻¹) at 25°C. Low temperature (10°C) reduced germling growth. Growth of germlings cultured under blue light was lower than in white light. Optimal growth of these germlings occurred at 25°C and 44 μmol photons m⁻² s⁻¹.     

Influence of agitation and aeration on growth and antibiotic production by <Emphasis Type="Italic">Xenorhabdus nematophila</Emphasis>

The effect of agitation and aeration on the growth and antibiotic production by Xenorhabdus nematophila YL001 grown in batch cultures were investigated. Efficiency of aeration and agitation was evaluated through the oxygen mass transfer coefficient (K _L a). With increase in K _L a, the biomass and antibiotic activity increased. Activity units of antibiotic and dry cell weight were increased to 232 U ml⁻¹ and 19.58 g l⁻¹, respectively, productivity in cell and antibiotic was up more than 30% when K _L a increased from 115.9 h⁻¹ to 185.7 h⁻¹. During the exponential growth phase, DO concentration was zero, the oxygen supply was not sufficient. So, based on process analysis, a three-stage oxygen supply control strategy was used to improved the DO concentration above 30% by controlling the agitation speed and aeration rate. The dry cell weight and activity units of antibiotic were further increased to 24.22 g l⁻¹ and 249 U ml⁻¹, and were improved by 24.0% and 7.0%, compared with fermentation at a constant agitation speed and a constant aeration rate (300 rev min⁻¹, 2.5 l min⁻¹).     

Optimization of production of caffeine demethylase by <Emphasis Type="Italic">Pseudomonas</Emphasis> sp. in a bioreactor

The effect of pH, aeration rate, and agitation rate on specific productivity of caffeine demethylase from Pseudomonas sp. was studied in a bioreactor. Maximum specific productivity of caffeine demethylase of 2,214 U g cell dry weight⁻¹ h⁻¹ was obtained at 0.27 vvm, 700 rpm, and pH 7.0. Under these conditions, volumetric oxygen transfer coefficient was 74.2 h⁻¹, indicating that caffeine demethylase production by Pseudomonas sp. was highly oxygen-dependent. Different metabolite formation at different agitation and aeration rates can be used as a strategy for recovery of pharmaceutically important metabolites from caffeine by manipulation of conditions in a bacterial culture. This is the first report on production of high levels of caffeine demethylase in bioreactors.     

Effects of agitation on the microalgae Phaeodactylum tricornutum and Porphyridium cruentum

The effect of mechanical agitation on the microalgae Phaeodactylum tricornutum and Porphyridium cruentum was investigated in aerated continuous cultures with and without the added shear protectant Pluronic F68. Damage to cells was quantified through a decrease in the steady state concentration of the biomass in the photobioreactor. For a given aeration rate, the steady state biomass concentration rose with increasing rate of mechanical agitation until an upper limit on agitation speed was reached. This maximum tolerable agitation speed depended on the microalgal species. Further increase in agitation speed caused a decline in the steady state concentration of the biomass. An impeller tip speed of >1.56 m s^–1 damaged P. tricornutum in aerated culture. In contrast, the damage threshold tip speed for P. cruentum was between 2.45 and 2.89 m s^–1. Mechanical agitation was not the direct cause of cell damage. Damage occurred because of the rupture of small gas bubbles at the surface of the culture, but mechanical agitation was instrumental in generating the bubbles that ultimately damaged the cells. Pluronic F68 protected the cells against damage and increased the steady state concentration of the biomass relative to operation without the additive. The protective effect of Pluronic was concentration-dependent over the concentration range of 0.01–0.10% w/v.     

Influence of culture vessel characteristics and agitation rate on gaseous exchange,hydrodynamic stress,and growth of embryogenic cork oak (<Emphasis Type="BoldItalic">Quercus suber</Emphasis> L.) cultures

Somatic embryogenesis can be induced in the leaves of cork oak (Quercus suber L.) trees. The use of this propagation system in multivarietal forestry requires the mass production of cloned plants at low cost. Investigations were made into the influence of three types of Erlenmeyer flask and three orbiting speeds (60, 110, and 160 rpm) on oxygen transfer rate (K_L a), the shear force index (SFI), biomass production, and the proliferation of embryogenic clumps (EMCs) in cultures during the proliferation phase. K_L a varied between 0.11 and 1.47 h⁻¹ without biomass production being limited by oxygen availability. The EMCs grew even in hypoxic conditions, although the suppression of gaseous exchange strongly reduced biomass production. Cultures with different levels of hydrodynamic stress and SFI values (1.4·10⁻³–8.8·10⁻³ cm min⁻¹) were obtained. Proliferation rates of EMCs increased with agitation rate and the SFI. The largest number of EMCs was obtained in baffled flasks agitated at 160 rpm (K_L a of 1.47 h⁻¹, and SFI of 8.8·10⁻³ cm min⁻¹) with mild hydrodynamic stress enhancing growth. Biomass production increased with agitation and hydrodynamic stress, but only when the SFI value was below 5·10⁻³ cm min⁻¹. The greatest biomass production was obtained in smooth 100 ml flasks agitated at 160 rpm. The differentiation of embryos was favoured by the lowest K_L a (0.11 h⁻¹) and SFI (1.40·10³ cm min⁻¹) values, achieved using these flasks when agitated at 60 rpm.     

Development of net energy intake models for drift-feeding juvenile coho salmon and steelhead

We developed models to predict the effect of water velocity on prey capture rates and on optimal foraging velocities of two sympatric juvenile salmonids, coho salmon and steelhead. Mean fish size was ~80 mm, the size of age I+ coho and steelhead during their second summer in Southeast Alaska streams, when size overlap suggests that competition might be strongest. We used experimentally determined prey capture probabilities to estimate the effect of water velocity on gross energy intake rates, and we modeled prey capture costs using experimental data for search and handling times and published models of swimming costs. We used the difference between gross energy intake and prey capture costs to predict velocities at which each species maximized net energy intake rate. Predicted prey capture rates for both species declined from ~75 to 30–40 prey/h with a velocity increase from 0.30 to 0.60 m·s⁻¹. We found little difference between coho and steelhead in predicted optimum foraging velocities (0.29 m·s⁻¹ for coho and 0.30 m·s⁻¹ for steelhead). Although prey capture ability appears to be more important than are prey capture costs in determining optimum foraging velocities, capture costs may be important for models that predict fish growth. Because coho are assumed to pay a greater swimming cost due to a less hydrodynamic body form, we also modeled 10 and 25% increases in hydrodynamic drag to assess the effect of increased prey capture costs. This reduced optimum velocity by 0 and 0.01 m∙s⁻¹, respectively. Habitat segregation among equal-sized coho and steelhead does not appear to be related to the effects of water velocity on their respective foraging abilities.     

Physiological differences in the growth of <Emphasis Type="Italic">Sargassum horneri</Emphasis> between the germling and adult stages

The effects of temperature, irradiance, and daylength on Sargassum horneri growth were examined at the germling and adult stages to discern their physiological differences. Temperature–irradiance (10, 15, 20, 25, 30°C × 20, 40, 80 μmol photons m⁻²s⁻¹) and daylength (8, 12, 16, 24 h) experiments were carried out. The germlings and blades of S. horneri grew over a wide range of temperatures (10–25°C), irradiances (20–80 μmol photons m⁻²s⁻¹), and daylengths (8–24 h). At the optimal growth conditions, the relative growth rates (RGR) of the germlings were 21% day⁻¹ (25°C, 20 μmol photons m⁻²s⁻¹) and 13% day⁻¹ (8 h daylength). In contrast, the RGRs of the blade weights were 4% day⁻¹ (15°C, 20 μmol photons m⁻²s⁻¹) and 5% day⁻¹ (12 h daylength). Negative growth rates were found at 20 μmol photons m⁻²s⁻¹ of 20°C and 25°C treatments after 12 days. This phenomenon coincides with the necrosis of S. horneri blades in field populations. In conclusion, we found physiological differences between S. horneri germlings and adults with respect to daylength and temperature optima. The growth of S. horneri germlings could be enhanced at 25°C, 20 μmol photons m⁻²s⁻¹, and 8 h daylength for construction of Sargassum beds and restoration of barren areas.     

Enhanced fructooligosaccharides and inulinase production by a <Emphasis Type="Italic">Xanthomonas campestris</Emphasis> pv. <Emphasis Type="Italic">phaseoli</Emphasis> KM 24 mutant

Xanthomonas campestris pv phaseoli produced an extracellular endoinulinase (9.24 ± 0.03 U mL⁻¹) in an optimized medium comprising of 3% sucrose and 2.5% tryptone. X. campestris pv. phaseoli was further subjected to ethylmethanesulfonate mutagenesis and the resulting mutant, X. campestris pv. phaseoli KM 24 demonstrated inulinase production of 22.09 ± 0.03 U mL⁻¹ after 18 h, which was 2.4-fold higher than that of the wild type. Inulinase production by this mutant was scaled up using sucrose as a carbon source in a 5-L fermenter yielding maximum volumetric (21,865 U L⁻¹ h⁻¹) and specific (119,025 U g⁻¹ h⁻¹) productivities of inulinase after 18 h with an inulinase/invertase ratio of 2.6. A maximum FOS production of 11.9 g L⁻¹ h⁻¹ and specific productivity of 72 g g⁻¹ h⁻¹ FOS from inulin were observed in a fermenter, when the mutant was grown on medium containing 3% inulin and 2.5% tryptone. The detection of mono- and oligosaccharides in inulin hydrolysates by TLC analysis indicated the presence of an endoinulinase. This mutant has potential for large-scale production of inulinase and fructooligosaccharides.     

Cultivation of the green alga, Codium fragile (Suringar) Hariot, by artificial seed production in Korea

Codium fragile (Suringar) Hariot is an edible green alga farmed in Korea using seed stock produced from regeneration of isolated utricles and medullary filaments. Experiments were conducted to reveal the optimal conditions for nursery culture and out-growing of C. fragile. Sampling and measurement of underwater irradiance were carried out at farms cultivating C. fragile at Wando, on the southwestern coast of Korea, from October 2004 to August 2005. Growth of erect thalli and underwater irradiance were measured over a range of depths for three culture stages. During the nursery cultivation stage (Stage I), growth rate was greatest at 0.5 m depth (0.055 ± 0.032 mm day⁻¹), where the average midday irradiance over 60 days was 924 ± 32 μmol photons m⁻² s⁻¹. During the pre-main cultivation stage (Stage II), the greatest growth rate occurred at a depth of 2 m (0.113 ± 0.003 mm day⁻¹) with an average irradiance of 248 ± 116 μmol photons m⁻² s⁻¹. For the main cultivation stage (Stage III) of the alga, thalli achieved the greatest increase in biomass at 1 m depth (7.2 ± 1.0 kg fresh wt m⁻¹). These results suggest that optimal growth at each cultivation stages of C. fragile could be controlled by depth of cultivation rope.     

Effects of temperature and light on the growth and geosmin production of Lyngbya kuetzingii (Cyanophyta)

The effects of temperature and light on the growth and geosmin production of Lyngbya kuetzingii were determined. Of the three temperatures tested, 10, 25 and 35°C, the maximal geosmin concentration and geosmin productivity were yielded at 10°C, while the highest chl a production was observed at 25°C. In the studies on light intensity, the maximal geosmin concentration and geosmin productivity were observed at 10 μmol m⁻² s⁻¹, while the highest chl a production was at 20 μmol m⁻² s⁻¹. It was suggested that more geosmin was synthesized with lower chl a demand. Meanwhile, the relative amounts of extra- and intracellular geosmin were investigated. Under optimum growth conditions (20 μmol m⁻² s⁻¹, 25°C; BG-11 medium), the amounts of extracellular geosmin increased as the growth progressed and reached the maximum in the stationary phase, while the intracellular geosmin reached its maximum value in the late exponential phase, and then began to decline. However, under the low temperature (10°C) or light (10 μmol m⁻² s⁻¹) conditions, more intracellular geosmin was synthesized and mainly accumulated in the cells. The proportions of extracellular geosmin were high, to 33.33 and 32.27%, respectively, during the stationary phase at 35°C and 20 μmol m⁻² s⁻¹. It was indicated that low temperature or light could stimulate geosmin production and favor the accumulation of geosmin in cells, while more intracellular geosmin may be released into the medium at higher temperatures or optimum light intensity.     

Effects of temperature,photosynthetic photon flux density,photoperiod and O<Subscript>2</Subscript> and CO<Subscript>2</Subscript> concentrations on growth rates of the symbiotic dinoflagellate, <Emphasis Type="Italic">Amphidinium</Emphasis> sp.

Symbiotic dinoflagellates of the species Amphidinium are expected to be pharmaceutically useful microalgae because they produce antitumor macrolides. A microalgae production system with a large number of cells at a high density has been developed for the efficient production of macrolide compounds. In the present study, the effects of culture conditions on the cellular growth rate of dinoflagellates were investigated to determine the optimum culture conditions for obtaining high yields of microalgae. Amphidinium species was cultured under conditions with six temperature levels (21–35°C), six levels of photosynthetic photon flux density (15–70 μmol photons m⁻² s⁻¹), three levels of CO₂ concentration (0.02–0.1%), and three levels of O₂ concentration (0.2–21%). The number of cells cultured in a certain volume of solution was monitored microscopically and the cellular growth rate was expressed as the specific growth rate. The maximum specific growth rate was 0.022 h⁻¹ at a temperature of 26°C and O₂ concentration of 5%, and the specific growth rate was saturated at a CO₂ concentration of 0.05%, a photosynthetic photon flux density of 35 μmol photons m⁻² s⁻¹ and a photoperiod of 12 h day⁻¹ upon increasing each environmental parameter. The results demonstrate that Amphidinium species can multiply efficiently under conditions of relatively low light intensity and low O₂ concentration.     

Growth characteristics of the cyanobacterium Nostoc flagelliforme in photoautotrophic, mixotrophic and heterotrophic cultivation

Nostoc flagelliforme is a terrestrial cyanobacterium with high economic value. Dissociated cells separated from a natural colony of N. flagelliforme were cultivated for 7 days under either phototrophic, mixotrophic or heterotrophic culture conditions. The highest biomass, 1.67 g L⁻¹ cell concentration, was obtained under mixotrophic culture, representing 4.98 and 2.28 times the biomass obtained in phototrophic and heterotrophic cultures, respectively. The biomass in mixotrophic culture was not the sum as that in photoautotrophic and heterotrophic cultures. During the first 4 days of culture, the cell concentration in mixotrophic culture was lower than the sum of those in photoautotrophic and heterotrophic cultures. However, from the 5th day, the cell concentration in mixotrophic culture surpassed the sum of those obtained from the other two trophic modes. Although the inhibitor of photosynthetic electron transport DCMU [3-(3,4-dichlorophenyl)-1,1-dimethylurea] efficiently inhibited autotrophic growth of N. flagelliforme cells, under mixotrophic culture they could grow by using glucose. The addition of glucose changed the response of N.flagelliforme cells to light. The maximal photosynthetic rate, dark respiration rate and light compensation point in mixotrophic culture were higher than those in photoautotrophic cultures. These results suggest that photoautotrophic (photosynthesis) and heterotrophic (oxidative metabolism of glucose) growth interact in mixotrophic growth of N. flagelliforme cells.     

Seasonal dynamics of fine root biomass, root length density, specific root length, and soil resource availability in a Larix gmelinii plantation

Fine root turnover is a major pathway for carbon and nutrient cycling in terrestrial ecosystems and is most likely sensitive to many global change factors. Despite the importance of fine root turnover in plant C allocation and nutrient cycling dynamics and the tremendous research efforts in the past, our understanding of it remains limited. This is because the dynamics processes associated with soil resources availability are still poorly understood. Soil moisture, temperature, and available nitrogen are the most important soil characteristics that impact fine root growth and mortality at both the individual root branch and at the ecosystem level. In temperate forest ecosystems, seasonal changes of soil resource availability will alter the pattern of carbon allocation to belowground. Therefore, fine root biomass, root length density (RLD) and specific root length (SRL) vary during the growing season. Studying seasonal changes of fine root biomass, RLD, and SRL associated with soil resource availability will help us understand the mechanistic controls of carbon to fine root longevity and turnover. The objective of this study was to understand whether seasonal variations of fine root biomass, RLD and SRL were associated with soil resource availability, such as moisture, temperature, and nitrogen, and to understand how these soil components impact fine root dynamics in Larix gmelinii plantation. We used a soil coring method to obtain fine root samples (⩽2 mm in diameter) every month from May to October in 2002 from a 17-year-old L. gmelinii plantation in Maoershan Experiment Station, Northeast Forestry University, China. Seventy-two soil cores (inside diameter 60 mm; depth intervals: 0–10 cm, 10–20 cm, 20–30 cm) were sampled randomly from three replicates 25 m × 30 m plots to estimate fine root biomass (live and dead), and calculate RLD and SRL. Soil moisture, temperature, and nitrogen (ammonia and nitrates) at three depth intervals were also analyzed in these plots. Results showed that the average standing fine root biomass (live and dead) was 189.1 g·m⁻²·a⁻¹, 50% (95.4 g·m⁻²·a⁻¹) in the surface soil layer (0–10 cm), 33% (61.5 g·m⁻²·a⁻¹), 17% (32.2 g·m⁻²·a⁻¹) in the middle (10–20 cm) and deep layer (20–30cm), respectively. Live and dead fine root biomass was the highest from May to July and in September, but lower in August and October. The live fine root biomass decreased and dead biomass increased during the growing season. Mean RLD (7,411.56 m·m⁻³·a⁻¹) and SRL (10.83 m·g⁻¹·a⁻¹) in the surface layer were higher than RLD (1 474.68 m·m⁻³·a⁻¹) and SRL (8.56 m·g⁻¹·a⁻¹) in the deep soil layer. RLD and SRL in May were the highest (10 621.45 m·m⁻³ and 14.83m·g⁻¹) compared with those in the other months, and RLD was the lowest in September (2 198.20 m·m⁻³) and SRL in October (3.77 m·g⁻¹). Seasonal dynamics of fine root biomass, RLD, and SRL showed a close relationship with changes in soil moisture, temperature, and nitrogen availability. To a lesser extent, the temperature could be determined by regression analysis. Fine roots in the upper soil layer have a function of absorbing moisture and nutrients, while the main function of deeper soil may be moisture uptake rather than nutrient acquisition. Therefore, carbon allocation to roots in the upper soil layer and deeper soil layer was different. Multiple regression analysis showed that variation in soil resource availability could explain 71–73% of the seasonal variation of RLD and SRL and 58% of the variation in fine root biomass. These results suggested a greater metabolic activity of fine roots living in soil with higher resource availability, which resulted in an increased allocation of carbohydrate to these roots, but a lower allocation of carbohydrate to those in soil with lower resource availability. __________ Translated from Acta Phytoecologica Sinica, 2005, 29(3): 403–410 [译自: 植物生态学报, 2005, 29(3): 403–410]     

In vitro clonal propagation of an aromatic medicinal herb Ocimum basilicum L. (sweet basil) by axillary shoot proliferation

Summary An efficient protocol for in vitro propagation of an aromatic and medicinal herb Ocimum basilicum L. (sweet basil) through axillary shoot proliferation from nodal explants, collected from field-grown plants, is described. High frequency bud break and maximum number of axillary shoot formation was induced in the nodal explants on Murashige and Skoog (1962) medium (MS) containing N⁶-benzyladenine (BA). The nodal explants required the presence of BA at a higher concentration (1.0 mg·l⁻¹, 4.4 μM) at the initial stage of bud break; however, further growth and proliferation required transfer to a medium containing BA at a relatively low concentration (0.25 mg·gl⁻¹, 1.1 μM). Gibberellic (GA₃) at 0.4 mg·l⁻¹ (1.2 μM) added to the medium along with BA (1.0 mg·l⁻¹, 4.4 μM) markedly enhanced the frequency of bud break. The shoot clumps that were maintained on the proliferating medium for longer durations, developed inflorescences and flowered in vitro. The shoots formed in vitro were rooted on half-strength MS supplemented with 1.0 mg·l⁻¹ (5.0 μM) indole-3-butyric acid (IBA). Rooted plantlets were successfully acclimated in vermi-compost inside a growth chamber and eventually established in soil. All regenerated plants were identical to the donor plants with respect to vegetative and floral morphology.     

Light-Dependency of Growth and Secondary Metabolite Production in the Captive Zooxanthellate Soft Coral Sinularia flexibilis

The branching zooxanthellate soft coral Sinularia flexibillis releases antimicrobial and toxic compounds with potential pharmaceutical importance. As photosynthesis by the symbiotic algae is vital to the host, the light-dependency of the coral, including its specific growth rate (μ day⁻¹) and the physiological response to a range of light intensities (10–1,000 μmol quanta m⁻² s⁻¹) was studied for 12 weeks. Although a range of irradiances from 100 to 400 μmol quanta m⁻² s⁻¹ was favorable for S. flexibilis, based on chlorophyll content, a light intensity around 100 μmol quanta m⁻² s⁻¹ was found to be optimal. The contents of both zooxanthellae and chlorophyll a were highest at 100 μmol quanta m⁻² s⁻¹. The specific budding rate showed almost the same pattern as the specific growth rate. The concentration of the terpene flexibilide, produced by this species, increased at high light intensities (200–600 μmol quanta m⁻² s⁻¹).     

Optimization of culture conditions and scale-up to pilot and plant scales for coenzyme Q<Subscript>10</Subscript> production by <Emphasis Type="Italic">Agrobacterium tumefaciens</Emphasis>

This report describes the optimization of culture conditions for coenzyme Q₁₀ (CoQ₁₀) production by Agrobacterium tumefaciens KCCM 10413, an identified high-CoQ₁₀-producing strain (Kim et al., Korean patent. 10-0458818, 2002b). Among the conditions tested, the pH and the dissolved oxygen (DO) levels were the key factors affecting CoQ₁₀ production. When the pH and DO levels were controlled at 7.0 and 0–10%, respectively, a dry cell weight (DCW) of 48.4 g l⁻¹ and a CoQ₁₀ production of 320 mg l⁻¹ were obtained after 96 h of batch culture, corresponding to a specific CoQ₁₀ content of 6.61 mg g-DCW⁻¹. In a fed-batch culture of sucrose, the DCW, specific CoQ₁₀ content, and CoQ₁₀ production increased to 53.6 g l⁻¹, 8.54 mg g-DCW⁻¹, and 458 mg l⁻¹, respectively. CoQ₁₀ production was scaled up from a laboratory scale (5-l fermentor) to a pilot scale (300 l) and a plant scale (5,000 l) using the impeller tip velocity (V _tip) as a scale-up parameter. CoQ₁₀ production at the laboratory scale was similar to those at the pilot and plant scales. This is the first report of pilot- and plant-scale productions of CoQ₁₀ in A. tumefaciens.     

Combined effect of temperature and light intensity on growth and extracellular polymeric substance production by the cyanobacterium Arthrospira platensis

The effects of light intensity and temperature on Arthrospira platensis growth and production of extracellular polymeric substances (EPS) in batch culture were evaluated using a three-level, full-factorial design and response surface methodology. Three levels were tested for each parameter (temperature: 30, 35, 40°C; light intensity: 50, 115, 180 μmol photons m⁻² s⁻¹). Both growth and EPS production are influenced mainly by the temperature factor but the interaction term temperature*light intensity also had a significant effect. In addition, conditions optimising EPS production are different from those optimising growth. The highest growth rate (0.414 ± 0.003 day⁻¹) was found at the lowest temperature (30°C) and highest light intensity (180 μmol photons m⁻² s⁻¹) tested, no optima were detectable within the given test range. Obviously, optima for growth must be at a temperature lower than 30°C and a light intensity higher than 180 μmol photons m⁻² s⁻¹. For EPS production, light intensity had a positive linear effect (optimum obviously higher than 180 μmol photons m⁻² s⁻¹), but for the temperature parameter a maximum effect was detectable at 35°C.