Limited use of Centritech Lab II Centrifuge in perfusion culture of rCHO cells for the production of recombinant antibody

Perfusion cultures of recombinant Chinese hamster ovary cells, producing recombinant antibody against the S surface antigen of Hepatitis B virus, were carried out in continuous and intermittent mode using a Centritech Lab II Centrifuge. In the continuous perfusion process, despite the absence of shear stress from the pump head, long-term operation was not possible because of continuously repeated exposure to oxygen limitation and low temperature, as well as shear stress from centrifugal force. In the intermittent perfusion processes, the frequency of cell-passage through the centrifuge was substantially reduced, compared with the continuous perfusion mode; however, the degree of reduction could not guarantee stable long-term operation. Although various operating parameters were applied in the intermittent perfusion cultures, high cell densities could not be maintained stably. In a single bioreactor culture system, a specific cell that is returned from the centrifuge to the bioreactor could be transferred from the bioreactor to the centrifuge again in the next cycle. These repetitive damages, caused by shear stress from the pump head and centrifugal force, as well as exposure to suboptimal conditions such as oxygen limitation and low temperature below 37 degrees C, were more serious at higher perfusion rates. Subsequently, damaged cells and dead cells were continuously accumulated in the bioreactor. Culture temperature shift from 37 to 33 degrees C increased antibody concentrations but showed inhibitory effects on cell growth. The negative effects of lowering culture temperature on cell growth overwhelmed the positive effects on antibody production. To protect cells from shear stress, Pluronic F-68 was 2-fold concentrated in the culture medium; nevertheless, a significantly higher concentration of Pluronic F-68 (2 g/L) may have inhibitory effects on cell growth.     

Optimizing performance of semi‐continuous cell culture in an ambr15™ microbioreactor using dynamic flux balance modeling

The ambr bioreactors are single‐use microbioreactors for cell line development and process optimization. With operating conditions for large‐scale biopharmaceutical production properly scaled down, microbioreactors such as the ambr15? can potentially be used to predict the effect of process changes such as modified media or different cell lines. While there have been some recent studies evaluating the ambr15? technology as a scale‐down model for fed‐batch operations, little has been reported for semi‐continuous or continuous operation. Gassing rates and dilution rates in the ambr15? were varied in this study to attempt to replicate performance of a perfusion process at the 5 L scale. At both scales, changes to metabolite production and consumption, and cell growth rate and therapeutic protein production were measured. Conditions were identified in the ambr15? bioreactor that produced metabolic shifts and specific metabolic and protein production rates that are characteristic of the corresponding 5 L perfusion process. A dynamic flux balance (DFB) model was employed to understand and predict the metabolic changes observed. The DFB model predicted trends observed experimentally, including lower specific glucose consumption and a switch from lactate production to consumption when dissolved CO₂ was maintained at higher levels in the broth. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 34:420–431, 2018     

High density culture of HeLa cells in a CelliGen perfusion system

A hollow fiber cartridge may be used in an extraneous recycle loop to facilitate perfusion operation of a stirred tank bioreactor. Retention of cells while removing waste products and replenishment with fresh nutrients allows higher than normal cell densities obtained in batch or continuous culture systems. This system successfully propagated HeLa cells to over 11 million viable cells per milliliter. Much higher perfusion rates (up to 4 vessel volumes per day) were necessary for high density culture of HeLa cells compared to BHK or a hybridoma cell line because of a much higher specific cellular metabolic rate. Cell specific glucose consumption rate, lactate production and ammonia production rates are several times higher for HeLa cells. Reproducible high cell densities and viabilities can be repeatedly obtained after harvest and dilution of a HeLa cell culture by partial drainage and reconstitution in the bioreactor.     

Bioreactor operating strategy inThalictrum rugosum plant cell culture for the production of berberine

Optimal substrate feeding strategy in bioreactor operation was investigated to increase the production of secondary metabolite in a high density culture of plant cell. It was accomplished by the previously proposed structured kinetic model that describes the cell growth and synthesis of the secondary metabolite, berberine, in a batch suspension culture ofThalictrum rugosum. Four types of operation strategies for sugar feeding intoT. rugosum culture were proposed based on the model, which were the periodic fedbatch operations to maintain the cell activity, the cell viability, and the specific production rate, and the perfusion operation to maintain the specific production rate. From the simulation results of these strategies, it could be found that the periodic fed-batch operation and the perfusion operation could achieve the higher volumetric production of berberine (mg berberine/L) and specific production yield (mg berberine/g dry cell weight) than those of batch cultures. Although the highest productivity (mg berberine/day) of berberine could be achieved by the periodic fed-batch operation to maintain the cell activity compared with the other strategies in the periodic fed-batch operations, the specific production yield was low due to the higher maximum dry cell weight than other cases. The periodic fed-batch operation to maintain cell viability resulted in the highest volumetric production of berberine and specific production yield compared with the other strategies. In the cases of maintaining the specific production rate, the per-formance of the periodic fed-batch operation was better than that of the perfusion operation in the respect of the volumetric production and productivity of berberine. In order to increase the volumetric production of berberine and to get the highest specific production yield, the periodic fed-batch operation to maintain cell viability could be chosen as the optimal operating strategy in high density, culture ofT. rugosum plant cell.     

Ajmalicine production by cell cultures of Catharanthus roseus: from shake flask to bioreactor

The productivity of a cell culture for the production of a secondary metabolite is defined by three factors: specific growth rate, specific product formation rate, and biomass concentration during production. The effect of scaling-up from shake flask to bioreactor on growth and production and the effect of increasing the biomass concentration were investigated for the production of ajmalicine by Catharanthus roseus cell suspensions. Growth of biomass was not affected by the type of culture vessel. Growth, carbohydrate storage, glucose and oxygen consumption, and the carbon dioxide production could be predicted rather well by a structured model with the internal phosphate and the external glucose concentration as the controlling factors. The production of ajmalicine on production medium in a shake flask was not reproduced in a bioreactor. The production could be restored by creating a gas regime in the bioreactor comparable to that in a shake flask. Increasing the biomass concentration both in a shake flask and in a stirred fermenter decreased the ajmalicine production rate. This effect could be removed partly by controlling the oxygen concentration in the more dense culture at 85% air saturation.     

连续灌流培养杂交瘤细胞生产单克隆抗体

自 2 0世纪 70年代以来 ,工程抗体在基础医学研究、临床诊断和治疗 ,以及免疫预防等领域中的广泛应用 ,大大促进了其产业化的进程。目前工业化生产单克隆抗体的主要方法是通过发酵罐、中空纤维和固定床等生物反应器培养系统 ,以微载体、微包囊法在体外大规模高密度培养杂交瘤细胞 ,再通过相关的纯化手段浓缩纯化制备抗体[1 ,2 ] 。就操作方式而言 ,一般采用两个基本策略 :①大容量高密度的悬浮培养 ,最多采用的是搅拌式气升式生物反应器 ,通过微载体依托细胞相对固定化 ,降低了搅拌培养时对细胞的剪切力 ,提高细胞的密度和稳定性及生产率。…     

Application of a cell-once-through perfusion strategy for production of recombinant antibody from rCHO cells in a Centritech Lab II centrifuge system

Based upon the results of scale-down intermittent perfusion processes, a cell-once-through (COT) perfusion concept was applied to a dual bioreactor system coupled to a Centritech Lab II centrifuge for culture of recombinant Chinese hamster ovary (rCHO) cells for monoclonal antibody production. In this new culture mode, i.e., the COT perfusion process, total spent medium was transferred to the centrifuge and a fixed percentage was removed. Approximately 99% of the viable cells are transferred to another bioreactor filled with fresh medium by single operation of the Centritech Lab II centrifuge system for about 30 min. Accordingly, a significant reduction of the cell-passage frequency to the centrifuge led to minimization of cell damage caused by mechanical shear stress, oxygen limitation, nutrient limitation, and low temperature outside the bioreactor. The effects of culture temperature shift and fortified medium on cell growth and recombinant antibody production in the COT perfusion process were investigated. Although the suppressive effects of low culture temperature on cell growth led to a loss of stability in a long-term COT perfusion culture system, the average antibody concentration at 33 degrees C was 157.8 mg/L, approximately 2.4-fold higher than that at 37 degrees C. By the use of a fortified medium at 37 degrees C, rCHO cells were maintained at high density above 1.2 x 10(7) cells/mL, and antibody was produced continuously in a range of 260-280 mg/L in a stable long-term COT perfusion culture. The proposed new culture mode, the COT perfusion approach, guarantees the recovery of rCHO cells damaged by lowered temperature or high lactate and ammonium concentration. It will be an attractive choice for minimization of cell damage and stable long-term antibody production with high cell density.     

Taxol (paclitaxel) production using free and immobilized cells of Taxus cuspidata

The production characteristics for Taxol (paclitaxel) using free and immobilized cells of Taxus cuspidata were investigated in a perfusion culture bioreactor. Although the cell growth was inhibited by higher dilution rates, the specific production rate of Taxol was increased by perfusion compared with that using batch operation. Perfusion cultures using a nylon-mesh cell separator for free suspension cells showed similar production profiles to those obtained using immobilized cells. Continuous Taxol production was successfully obtained at an approximate specific production rate of 0.3 mg/g DCW (dry cell weight) per day for up to 40 days. (c) 1997 John Wiley & Sons, Inc.     

Hybridoma growth and antibody production as a function of cell density and specific growth rate in perfusion culture

Steady state metabolic parameters for hybridoma cell line H22 were determined over a wide range of cell densities and specific growth rates in a filtration based homogeneous perfusion reactor. Operating the reactor at perfusion rates of 0.75, 2.0, and 2.9 day(-1)(each at four different specific growth rates), viable cell densities as high as 2 x 10(7) cells/mL were obtained. For the cell line under investigation, the specific monoclonal antibody production rate was found to be a strong function of the viable cell density, increasing with increasing cell density. In contrast, most of the substrate consumption and product formation rates were strong functions of the specific growth rate. Substrate metabolism became more efficient at high cell densities and low specific growth rates. The Specific rates of metabolite formation and the apparent yields of lactate from glucose and ammonia from glutamine decreased at low specific growth rates and high cell densities. While the specific oxygen consumption rate was independent of the specific growth rate and cell density, ATP production was more oxidative at lower specific growth rate and higher cell density. These observed shifts are strong indications of the production potential of high-density perfusion culture. (c) 1995 John Wiley & Sons, Inc.     

Effects of oxygen transport on 3-d human mesenchymal stem cell metabolic activity in perfusion and static cultures: experiments and mathematical model

Human mesenchymal stem cells (hMSCs) have unique potential to develop into functional tissue constructs to replace a wide range of tissues damaged by disease or injury. While recent studies have highlighted the necessity for 3-D culture systems to facilitate the proper biological, physiological, and developmental processes of the cells, the effects of the physiological environment on the intrinsic tissue development characteristics in the 3-D scaffolds have not been fully investigated. In this study, experimental results from a 3-D perfusion bioreactor system and the static culture are combined with a mathematical model to assess the effects of oxygen transport on hMSC metabolism and proliferation in 3-D constructs grown in static and perfusion conditions. Cells grown in the perfusion culture had order of magnitude higher metabolic rates, and the perfusion culture supports higher cell density at the end of cultivation. The specific oxygen consumption rate for the constructs in the perfusion bioreactor was found to decrease from 0.012 to 0.0017 micromol/10(6) cells/h as cell density increases, suggesting intrinsic physiological change at high cell density. BrdU staining revealed the noneven spatial distribution of the proliferating cells in the constructs grown under static culture conditions compared to the cells that were grown in the perfusion system. The hypothesis that the constructs in static culture grow under oxygen limitation is supported by higher Y(L/G) in static culture. Modeling results show that the oxygen tension in the static culture is lower than that of the perfusion unit, where the cell density was 4 times higher. The experimental and modeling results show the dependence of cell metabolism and spatial growth patterns on the culture environment and highlight the need to optimize the culture parameters in hMSC tissue engineering.     

Semicontinuous and continuous production of penicillin-G by Penicillium chrysogenum cells immobilized in kappa-carrageenan beads

Conidia of Penicillium chrysogenum were immobilized in K-carrageenan beads and then incubated in a growth-supporting medium to yield a penicillin producing immobilized cell mass. These in situ grown immobilized cells were used for the semicontinuous (replacement cultures)and continuous (fluidized bioreactor culture) production of penicillin-G. When periodically replaced into a minimal production medium, immobilized cells exhibited a half-life for penicillin production which was ninefold greater than that exhibited by free cells. The half-life of penicillin production and the yield of penicillin from glucose in such a replacement culture were greatly affected by the frequency of replacement and by the production medium's pH and concentration of glucose, phosphate, and trace metal nutrients. A penicillin-producing continuous flow bioreactor (150 mL), employing immobilized cells, was operated for up to 16 days. The best specific penicillin productivity (1.2 mg/g cells/h)yield from glucose (7.0 mg/g glucose) and half-life of production (15 days) were obtained when the feed medium contained 10 g/L of glucose, the pH was maintained at 7.0, the relative dissolved oxygen concentration was ca. 40%; and the residence time was 20 h.     

Erythropoietin production from CHO cells grown by continuous culture in a fluidized-bed bioreactor.

A Chinese hamster ovary (CHO) cell line that expresses human erythropoietin (huEPO) was in a 2-L Cytopilot fluidized-bed bioreactor with 400 mL macroporous Cytoline-1 microcarriers and a variable perfusion rate of serum-free and protein-free medium for 48 days. The cell density increased to a maximum of 23 x 10(6) cells/mL, beads on day 27. The EPO concentration increased to 600 U/mL during the early part of the culture period (on day 24) and increased further to 980 U/mL following the addition of a higher concentration of glucose and the addition of sodium butyrate. The EPO concentration was significantly higher (at least 2x than that in a controlled stirred-tank bioreactor, in a spinner flask, or in a stationary T-flask culture. The EPO accumulated to a total production of 28,000 kUnits over the whole culture period. The molecular characteristics of EPO with respect to size and pattern of glycosylation did not change with scale up. The pattern of utilization and production of 18 amino acids was similar in the Cytopilot culture to that in a stationary batch culture in a T-flask. The concentration of ammonia was maintained at a low level (< 2 mM) over the entire culture period. The specific rate of consumption of glucose, as well as the specific rates of production of lactate and ammonia, were constant throughout the culture period indicating a consistent metabolic behavior of the cells in the bioreactor. These results indicate the potential of the Cytopilot bioreactor culture system for the continuous production of a recombinant protein over several weeks.     

High‐yield secretion of recombinant proteins expressed in tobacco cell culture with a designer glycopeptide tag: Process development

Low‐yield protein production remains the most significant economic hurdle with plant cell culture technology. Fusions of recombinant proteins with hydroxyproline‐O‐glycosylated designer glycopeptide tags have consistently boosted secreted protein yields. This prompted us to study the process development of this technology aiming to achieve productivity levels necessary for commercial viability. We used a tobacco BY‐2 cell culture expressing EGFP as fusion with a glycopeptide tag comprised of 32 repeat of ”Ser‐Pro“ dipeptide, or (SP)₃₂, to study cell growth and protein secretion, culture scale‐up, and establishment of perfusion cultures for continuous production. The BY‐2 cells accumulated low levels of cell biomass (～7.5 g DW/L) in Schenk & Hildebrandt medium, but secreted high yields of (SP)₃₂‐tagged EGFP (125 mg/L). Protein productivity of the cell culture has been stable for 6.0 years. The BY‐2 cells cultured in a 5‐L bioreactor similarly produced high secreted protein yield at 131 mg/L. Successful operation of a cell perfusion culture for 30 days was achieved under the perfusion rate of 0.25 and 0.5 day^?1, generating a protein volumetric productivity of 17.6 and 28.9 mg/day/L, respectively. This research demonstrates the great potential of the designer glycopeptide technology for use in commercial production of valuable proteins with plant cell cultures.     

Muscle oxygen extraction and perfusion heterogeneity during continuous and intermittent static exercise.

The purpose of this study was to compare the effects of intermittent and continuous static exercise on muscle perfusion, perfusion heterogeneity, and oxygen extraction. Perfusion and oxygen uptake of quadriceps femoris muscle were measured in 10 healthy men by using positron emission tomography and [(15)O]H(2)O and [(15)O]O(2) first during intermittent static exercise [10% of maximal static force (MSF)] and thereafter during continuous static exercise at the same tension-time level (5% static; 5% of MSF). In 4 of these subjects, perfusion was measured during continuous static exercise with 10% of MSF (10% continuous) instead of the second [(15)O]O(2) measurement. Muscle oxygen consumption was similar during intermittent and 5% continuous, but muscle perfusion was significantly higher during 5% continuous. Consequently, muscle oxygen extraction fraction was lower during 5% continuous. Perfusion was also more heterogeneous during 5% continuous. When exercise intensity was doubled during continuous static exercise (from 5% continuous to 10% continuous), muscle perfusion increased markedly. These results suggest that continuous, low-intensity static exercise decreases muscle oxygen extraction and increases muscle perfusion and its heterogeneity compared with intermittent static exercise at the same relative exercise intensity.     

Continuous cultivation of a human intestinal microflora at high cell concentration via controlled culture recycle

A bioreactor system equipped with a hollow fiber cross-filtration module was used for continuous cultivation of Lactobacillus acidophilus at high cell concentrations. The growth rate did not correlate with the lactate concentration if the residual glucose concentration was kept nearly zero in the culture broth. To achieve this, an effective control method of medium feed rate was developed on the basis of the correlation between the specific glucose consumption rate (nu) and the specific cell growth rate (mu), i.e. nu = 52.90 mu + 0.39. Growth up to 50 g dry wt l-1 was achieved without glucose accumulation under the total cell recycle. Via the partial cell recycle, continuous biomass production was achieved with a steady-state L. acidophilus concentration and dilution rate being 40 gl-1 and 0.09 h-1. © Rapid Science Ltd. 1998     

Dynamic change of metabolites and nutrients in suspension cells of <Emphasis Type="Italic">Panax Quinquefolium</Emphasis> L. in bioreactor

In order to understand how the nutrient elements were taken up during the cell growth as well as the production of metabolites, it was quite necessary to identify the dynamic change of metabolites and nutrients in suspension cells of Panax quinquefolium in bioreactor. In this study, dynamic accumulation of biomass and ginsenosides Re, Rb1 and polysaccharide as well as major nutrients consumption in cell suspension culture of P. quinquefolium in a 5-L stirred tank bioreactor were investigated. The dry cell weight and the contents of ginsenosides Re, Rb1 and polysaccharide reached the maximum peak simultaneously on about 21 days and the results showed that cell growth and metabolites synthesis related to nutrients consumption. For this reason, we supposed that the contents of metabolites can be increased through added nutrient at the right moment. These results provided theory reference for two-stage or continuous perfusion culture in suspension cells of P. quinquefolium in bioreactor.     

High density culture of mammalian cells with dynamic perfusion based on on-line oxygen uptake rate measurements

In a continuous culture with cell retention the perfusion rate must be adjusted dynamically to meet the cellular demand. An automated mechanism of adjusting the perfusion rate based on real-time measurement of the metabolic load of the bioreactor is important in achieving a high cell concentration and maintaining high viability. We employed oxygen uptake rate (OUR) measurement as an on-line metabolic indicator of the physiological state of the cells in the bioreactor and adjusted the perfusion rate accordingly. Using an internal hollow fiber microfiltration system for total cell retention, a cell concentration of almost 10⁸ cells/mL was achieved. Although some aggregates were formed during the cultivation, the viability remained high as examined with confocal microscopy after fluorescent vital staining. The results demonstrate that on-line OUR measurement facilitates automated dynamic perfusion and allows a high cell concentration to be achieved.     

杂交瘤细胞培养中摄氧速率(OUR)的在线检测及其与细胞生长及代谢的关系

在批式及灌流培养条件下研究了杂交瘤细胞在无血清培养基中的生长、代谢情况与氧消耗的关系。应用动力学方法在线进行OUR的检测,同时离线取样检测其他参数。结果发现OUR与谷氨酰胺的消耗、抗体的生成及活细胞密度间有明显的相关关系,进一步的分析还发现在对数生长期,OUR与活细胞密度间具有良好的线性关系,qOUR(0.103±0.028)×10^-12mol/cell/h,可以通过它来进行细胞密度的在线检测。并通过以ΔOUR=0时刻作为灌流调整点进行连续灌流培养的初步实验验证了OUR作为培养过程反馈控制参数的可能性。     

Bioreactor operation for transgenic Nicotiana tabacum cell cultures and continuous production of recombinant human granulocyte-macrophage colony-stimulating factor by perfusion culture

The production of hGM-CSF was investigated in both a flask and a 5-l bioreactor, using transgenic Nicotiana tabacum suspension cells. While the maximum cell density and secreted hGM-CSF in the flask were 15.4 g l⁻¹ and 6.5 μg l⁻¹, respectively, those in the bioreactor were 15.6 g l⁻¹ and 7.6 μg l⁻¹. No detectable growth inhibition, shorter production of hGM-CSF and reduced cell viability in the batch bioreactor were observed under the specific conditions used compared with the flask culture. To improve the productivity, a perfusion culture was carried out in the bioreactor, with three different perfusion rates (0.5, 1.0 and 2.0 day⁻¹). In all cases, the hGM-CSF in the medium was significantly increased during the overall culture period (16 days), with maximum values 3.0-, 9.4- and 6.0-fold higher than those obtained in the batch cultures, respectively, even though the intracellular hGM-CSF content was not significantly varied by the perfusion rate. In terms of the total amount of hGM-CSF secreted, 205.5, 1073.2 and 1246.3 μg accumulated in the perfusate within 16 days at the perfusion rates of 0.5, 1.0 and 2.0 day⁻¹, respectively. It was concluded that the beneficial effect of perfusion on the production of hGM-CSF originated from the reduced proteolytic degradation due to the lower protease activity caused by the perfusion. Additionally, the cell growth and physiology in the perfusion culture were somewhat negatively affected by the increased perfusion rate, although the dry cell density steadily increased, and as a result, 19.4, 22.4 and 22.9 g l⁻¹ of maximum cells were obtained with perfusion rates of 0.5, 1.0 and 2.0 day⁻¹, respectively. This work highlighted the importance of proteolytic degradation in plant cell cultures for the production of secretory proteins and the feasibility of perfusion strategies for the continuous production of foreign proteins by the prevention of protein loss due to proteolytic enzymes.     

A high-rate perfusion bioreactor for plant cells

A perfusion bioreactor allowing continuous extraction of secondary metabolites was designed and challenged for Eschscholtzia californica plant cell suspensions. Four sedimentation columns mounted inside a 2.5-L bioreactor separated single cells and cell aggregates from the culture medium. Cells were elicited with chitin at day 4 and the liquid medium free of cells and debris was then continuously pumped to the extraction columns containing fluidized XAD-7 resins, and then recirculated back to the cell suspension. A medium upward velocity corresponding to cell sedimentation velocity maintained a stable cell/medium separation front in the columns for sedimented cell volume (SCV) of 90% (70% packed cell volume, PCV). Two perfusion bioreactor cultures of 10 and 14 days were performed. A maximum dilution rate of 20.4/day was reached from day 4 to day 6, and was then reduced to 5/day at day 9 for 55% SCV. Control cultures were performed without and with free extraction resins into the cell suspension. Perfusion cultures showed similar specific growth rates of 0.24 +/- 0.04/day before and after elicitation. However, production level in the perfusion cultures was similar to that from the culture without resins with a maximum of 2.06 micromole/gDW total alkaloids, with 1.54 micromole/gDW in the resins. Cultures with free resins resulted in 30.94 micromole/gDW with 28.4 +/- 8.8 micromole/gDW in the resins. Difference in the cells nutritional state from elicitation was identified as a major cause in the production reduction. However, pathway to chelilutine was favored in the continuous extraction culture.