A method for the decrease of phenolic content in commercial canola meal using an enzyme preparation secreted by the white-rot fungus Trametes versicolor

An enzymatic process for upgrading the quality of canola meal (CM) by decreasing its phenolic content was investigated. The new method was based on the addition of the enzyme preparation from white-rot fungus Trametes versicolor to the meal-buffer slurry. A 98% decrease in the concentration of SAE was observed after 1 h of the treatment. The following process variables were considered for optimizing the process: pH, temperature, enzyme, meal, and oxygen concentrations. It was found that: (1) the natural buffering capacity of CM resulted in a negligible effect of the pH of the buffer, which was used as the continuous phase in the process, on the extent of decrease in sinapic acid esters (SAE); (2) the system was saturated with the enzyme when its concentration was 4 nkat/mL of the continuous phase; and (3) the optimum temperature was 50 degrees C. The process could be carried out even at higher temperatures due to the protective action of CM, which resulted in an increase in the thermal stability of the enzyme. The particle size influenced the extraction of the SAE from the meal, indicating that, at lower SAE concentrations, the process became diffusion limited. This result, together with those showing no effect of the intensity of agitation, indicated that the enzymatic process can be characterized by high Biot numbers. During the enzymatic process, the molar concentration of available oxygen can become a limiting factor when it is more than four times lower than the molar concentration of phenolics in the treated meal. The new enzymatic method was compared with other methods reported in the literature for the decrease in the phenolic content of rapeseed meals. It was found that, among the methods tested, the enzymatic treatment was the most effective, followed by the lime treatment. The enzymatic process did not reduce the quality of the protein isolates prepared from the CM. After the addition of a simple acetone-washing step, the isolate from the enzymatically treated meal had even better properties. Copyright 1999 John Wiley & Sons, Inc.     

Enzymatic decrease in the phenolic content of canola meal using concentrated aqueous or aqueous/hexane slurries

An enzymatic process to decrease the phenolic content in canola meal was investigated. The new method was based on the addition of an enzyme preparation from the white-rot fungus Trametes versicolor to concentrated meal-buffer slurries. This approach eliminated the extraction of the valuable meal components such as proteins and carbohydrates. Two systems were considered: (i) slurries with canola meal concentrations higher than 33% [w/v]; (ii) slurries with canola meal concentrations equal to or less than 12.5% [w/v] with n-hexane as the main component of the continuous phase. The concentration of sinapic acid esters decreased by 99% after a 1.5, 2 and 3 hour long treatment of the meal with an initial moisture content of 75% at 90°C, 70°C and 50°C, respectively. The process was carried out at temperaturs as high as 110°C. Both the enzyme and the moisture concentrations influenced the enzymatic process and their action was coupled. The concentration of oxygen strongly affected the process. The enzymatic process was able to be carried out in the presence of hexane as the main component of the continuous phase. The optimum temperature for such a process was 30–40°C, At 30°C, after 1 h of treatment, the meal phenolic content was decreased by 97%. The water uptake by the meal was diminished in the presence of hexane.     

Decrease of phenolic content in canola meal using a polyphenol oxidase preparation from Trametes versicolor: Effect of meal saccharification

A process to decrease the phenolic content of canola meal using a polyphenol oxidase preparation from Trametes versicolor was carried out in the presence and absence of cell wall solubilizing enzymes. Eighty five percent of the polysaccharide fraction of the cell wall of canola meal was solubilized in the process. A complete decrease in phenolic content was observed in the presence of xylanase or cellulase preparations after 16 and 36 hours of treatment, respectively. The initial rates of the process decreased by 10% and 5% in the presence of xylanase and cellulase preparations, respectively.     

Stabilization of quaternary structure of water-soluble quinoprotein glucose dehydrogenase

Water-soluble quinoprotein glucose dehydrogease (PQQGDH-B) is a dimeric enzyme whose application for glucose sensing is the focus of much attention. We attempted to increase the thermal stability of PQQGDH-B by introducing a disulfide bond at the dimer interface. The Ser residue at position 415 was selected for substitution with Cys, as structural information revealed that its side chains face each other at the dimer interface of PQQGDH-B. PQQGDH-B with Ser415Cys showed 30-fold greater thermal stability at 55°C than did the wild-type enzyme without any decrease in catalytic activity. After incubation at 70°C for 10 min, Ser415Cys retained 90% of the GDH activity of the wild-type enzyme. Disulfide bond formation between the mutant subunits was confirmed by analyses with sodium dodecylsulfate-polyacrylamide gel electrophoresis in the presence and absence of reductants. Our results indicate that the introduction of one Cys residue in each monomer of PQQGDH-B resulted in formation of a disulfide bond at the dimer interface and thus achieved a large increase in the thermal stability of the enzyme.     

Activation and stabilization of cardiac adenylate cyclase by GTP analog and fluoride.

The rate of cyclic AMP formation by rabbit heart membrane particles decreased at assay temperatures greater than 30 °C. Adenylate cyclase [ATP pyrophosphate-lyase (cyclizing), EC 4.6.1.1] activity (assayed at 24 °C) decreased exponentially with time of preincubation at 30 or 37 °C, providing evidence for the instability of this enzyme. The half-life, t_1/2, of the enzyme at 37 °C was 9.9 min in the absence and 4.4 min in the presence of MgCl₂. The activity was most labile in the presence of 50 m m Mg²⁺ and 1 m m ATP, having t_1/2 = 1.3min. Prior incubation of membranes with the GTP analog, guanyl-5′-yl imidodiphosphate [Gpp(NH)p], 0.1 m m, for 30 min at 37 °C produced maximal activation of adenylate cyclase; the rate of activation was temperature dependent and was increased in the presence of isoproterenol. The Gpp(NH)p-activated enzyme had increased thermal stability, t_1/2 = 170 min, and was also markedly more stable in the presence of Mg-ATP, t_1/2 = 72min, than nonactivated enzyme. Preactivation with F? (30 min at 24 °C) also stabilized the activity; t_1/2 > 70 min in the absence or presence of Mg-ATP. The Mg²⁺ concentration required for maximal activity was reduced from approximately 60 m m for nonactivated enzyme to 10 m m for the Gpp(NH)p- and F?activated enzyme.     

Thermal and chemical stability of solid-state enzymes

The thermal deactivation of solid-state acid-phosphatase has been studied, in the presence and in the absence of organic solvents. The experimental results have been modelled in terms of a single-step, non-linear, irreversible kinetic model. Enzyme stability was strongly affected by deactivation temperature and initial water content of the enzyme preparation. In contrast, no direct influence of solvent hydrophobicity was detected. The results were compared with those obtained in aqueous solution.     

The effect of some osmolytes on the activity and stability of mushroom tyrosinase

The thermodynamical stability and remained activity of mushroom tyrosinase (MT) fromAgaricus bisporus in 10 mM phosphate buffer, pH 6.8, stored at two temperatures of 4 and 40°C were investigated in the presence of three different amino acids (His, Phe and Asp) and also trehalose as osmolytes, for comparing with the results obtained in the absence of any additive. Kinetics of inactivation obeye the first order law. Inactivation rate constant (k_inact) value is the best parameter describing effect of osmolytes on kinetic stability of the enzyme. Trehalose and His have the smallest value of k_inact(0.7×10⁻⁴s⁻¹) in comparison with their absence (2.5×10⁻⁴s⁻¹). Moreover, to obtain effect of these four osmolytes on thermodynamical stability of the enzyme, protein denaturation by dodecyl trimethylammonium bromide (DTAB) and thermal scanning was investigated. Sigmoidal denaturation curves were analysed according to the two states model of Pace theory to find the Gibbs free energy change of denaturation process in aqueous solution at room temperature, as a very good thermodynamic criterion indicating stability of the protein. Although His, Phe and Asp induced constriction of MT tertiary structure, its secondary structure had not any change and the result was a chemical and thermal stabilization of MT. The enzyme shows a proper coincidence of thermodyanamic and structural changes with the presence of trehalose. Thus, among the four osmolytes, trehalose is an exceptional protein stabilizer.     

The effect of soluble alginate and calcium on β-galactosidase activity produced by the thermotolerant, ethanol-producing yeast strain Kluyveromyces marxianus imb3

Since it has previously been demonstrated that ethanol production by the thermotolerant yeast strain, Kluyveromyces marxianus IMB3 is more efficient in calcium alginate-based immobilization systems during growth on lactose-containing media, it was decided to examine the separate effects of soluble alginate and free calcium on the β-galactosidase activity produced by that organism. It was found that the presence of Ca²⁺ significantly increased the thermal stability of the activity at 45?°C, although the pH?and temperature optima remained the same in the presence and absence of that cation. It was also found that the presence of 2% (w/v) sodium alginate (soluble) had a very limited positive effect on the thermal stability of the enzyme at 45?°C, although it was found that activity was very significantly stimulated at that temperature. The activity was found to have an enhanced thermal stability at 30?°C in the presence of sodium alginate. The presence of sodium alginate in assay mixtures had no significant effect on the Km of the activity for the substrate o-nitrophenyl-β-D-galactoside. The results observed in the presence of either free calcium or soluble alginate may at least partially explain enhanced ethanol production by this microorganism in alginate-based immobilization systems.     

Ectoine-mediated protection of enzyme from the effect of pH and temperature stress: a study using Bacillus halodurans xylanase as a model

Compatible solutes are small, soluble organic compounds that have the ability to stabilise proteins against various stress conditions. In this study, the protective effect of ectoines against pH stress is examined using a recombinant xylanase from Bacillus halodurans as a model. Ectoines improved the enzyme stability at low (4.5 and 5.0) and high pH (11 and 12); stabilisation effect of hydroxyectoine was superior to that of ectoine and trehalose. In the presence of hydroxyectoine, residual activity (after 10 h heating at 50 °C) increased from about 45 to 86 % at pH 5 and from 33 to 89 % at pH 12. When the xylanase was incubated at 65 °C for 5 h with 50 mM hydroxyectoine at pH 10, about 40 % of the original activity was retained while no residual activity was detected in the absence of additives or in the presence of ectoine or trehalose. The xylanase activity was slightly stimulated in the presence of 25 mM ectoines and then gradually decreased with increase in ectoines concentration. The thermal unfolding of the enzyme in the presence of the compatible solutes showed a modest increase in denaturation temperature but a larger increase in calorimetric enthalpy.     

Some factors affecting the stability of glucoamylase immobilized on hornblende and on other inorganic supports

Glucoamylase from four different companies was studied: three had similar stability (half-life at 50°C about 140 hr); the fourth was less stable (half-life at 50°C about 20 hr). The immobilized enzymes were all less stable than their soluble counterparts: immobilized enzyme stability depended on the soluble enzyme used, the support, and method of immobilization. Thus enzyme bound to Enzacryl-TIO was less stable than enzyme bound to hornblende (metal-link method); this, in turn, was less stable than enzyme bound to hornblende by a silane–glutaraldehyde process. Bound enzyme stability was also improved by the presence of substrate or product (starch maltose or glucose). After 110 hr at 50°C in the presence of maltose (10% (w/v)) one preparation (a more stable soluble enzyme boul1d to hornblende by a silane–glutaraldehyde process) retained over 95% of its activity: activity loss was too low to permit the estimation of a half-life.     

Preparation of an immobilized–stabilized catalase derivative from Aspergillus niger having its multimeric structure stabilized: The effect of Zn on enzyme stability

Multimeric catalase from Aspergillus niger was immobilized on CNBr activated agarose, increasing the enzyme stability. However, it was found that some enzyme subunits could be desorbed to the supernatant after boiling the enzyme preparation in the presence of SDS or during thermal inactivation. Moreover, a positive enzyme concentration-enzyme stability correlation was detected in the immobilized preparation. This suggested the existence of some dissociation mechanism as a first step in the enzyme inactivation. The treatment of the immobilized enzyme with aldehyde–dextran permitted to fully stabilize its multimeric structure, but even this preparation exhibited an enzyme concentration-stability correlation. The presence of EDTA reduced the enzyme stability, suggesting that some cation could be involved in enzyme stability. It was found that 10 mM Zn²⁺ increased the enzyme stability of this immobilized–stabilized preparation. Now, the dilution of the biocatalyst did not produce a reduction in the enzyme stability.Thus, we have prepared an immobilized enzyme that does not release any subunit to the medium even after inactivation, and found that Zn²⁺ has a very positive effect on the stability of this immobilized–stabilized enzyme.     

Catalytic properties of glucoamylase immobilized on synthetic carbon material Sibunit

Glucoamylase (commercial preparation Glucavamorin) was immobilized by sorption on a carbon support Sibunit. Starch saccharification by the resulting biocatalyst (dextrin hydrolysis) was studied. Investigation of the effect of adsorptional immobilization on kinetic parameters of glucoamylase, including the rate constant of thermal inactivation, showed that immobilization of Glucavamorin on Sibunit resulted in a thousand-fold increase in glucoamylase stability in comparison with the dissolved enzyme. Presence of the substrate (dextrins) in the reaction mixture had a considerable stabilizing effect. Increase in dextrin concentration increases the thermostability of the immobilized enzyme. The overall factor of glucoamylase stabilization adsorbed on Sibunit with the presence of 53% dextrin solutions in comparison with the dissolved enzyme approximated 10⁵. The biocatalyst for starch saccharification made on the base of Subunit-adsorbed Glucavamorin had a high operational stability. Its half-inactivation time at 60°C exceeded 30 days.     

Efficient release of thermostable β-galactosidase by glycine addition and thermal treatment of Escherichia coli cells

Efficient release of thermostable β-galactosidase from a recombinant Escherichia coli by the addition of glycine to the culture broth and subsequent thermal treatment was investigated. The enzyme release rate was strongly dependent on glycine concentration. The enzyme release rate was almost proportional to glycine concentrations up to 2% in phosphate buffer; however, inactivation of the enzyme was not observed following incubation for up to 3 h at 70°C even in the presence of 10% glycine. In a preliminary experiment, severe thermal inactivation was observed in the presence of polyethylene glycol (PEG), but glycine was able to suppress the inactivation. Thermal treatment of the cell suspension was effective for the improvement of the enzyme release rate. In the absence of glycine, the enzyme release rate was low at 37 and 45°C, even though the initial release rate was high at 0.5 h and 60°C. The combination of thermal treatment and addition of glycine to the cell suspension significantly improved the initial enzyme release rate and the amount of enzyme released to the extracellular fraction at 37 and 45°C was as high as that at 60°C during a 2-h incubation.     

Effect of feather meal as proteic feeder on combi-CLEAs preparation for grape juice clarification

This work describes the preparation of combi-CLEAs of pectinases using feather meal as novel proteic feeder. Initially, four solvents were tested as precipitant agents, and ethanol was chosen as the best solvent. Subsequently, a 2³ factorial design was carried out to define the optimal conditions for combi-CLEAs preparation, which were set as 110 mM of glutaraldehyde, 0.66 mg protein mL⁻¹ and 5 h of reaction time. Then, the effect of BSA or feather meal (FM) as proteic feeders was evaluated. Combi-CLEAs, combi-CLEAs-BSA and combi-CLEAs-FM were characterized and evaluated by their activity recovery, optimal pH and temperature, operational and thermal stabilities and e effectiveness on juice clarification. The addition of feather meal increased two-fold the activity recovery compared to BSA. The thermal stability was similar for all combi-CLEAs, providing stabilization factors of 1.12, 1.48 and 1.53, respectively, for the combi-CLEA, combi-CLEA-FM and combi-CLEA-BSA, compared to free enzyme. CLEAs presented turbidity reduction near to 50%, 2.5-fold than soluble enzyme. Feather meal was used for the first time as proteic feeder for CLEA preparations and appears to be a good, and low price, alternative.     

Gene Cloning and Characterization of a Thermostable Phytase from Bacillus subtilis US417 and Assessment of its Potential as a Feed Additive in Comparison with a Commercial Enzyme

An extracellular phytase from Bacillus subtilis US417 (PHY US417) was purified and characterized. The purified enzyme of 41 kDa was calcium-dependent and optimally active at pH 7.5 and 55°C. The thermal stability of PHY US417 was drastically improved by calcium. Indeed, it recovered 77% of its original activity after denaturation for 10 min at 75°C in the presence of 5 mM CaCl₂, while it retained only 22% of activity when incubated for 10 min at 60°C without calcium. In addition, PHY US417 was found to be highly specific for phytate and exhibited pH stability similar to Phyzyme, a commercial phytase with optimal activity at pH 5.5 and 60°C. The phytase gene was cloned by PCR from Bacillus subtilis US417. Sequence analysis of the encoded polypeptide revealed one residue difference from PhyC of Bacillus subtilis VTTE-68013 (substitution of arginine in position 257 by proline in PHY US417) which was reported to exhibit lower thermostability especially in the absence of calcium. With its neutral pH optimum as well as its great pH and thermal stability, the PHY US417 enzyme presumed to be predominantly active in the intestine has a high potential for use as feed additive.     

Enhancement of operation and storage stability of glucoamylase from Aspergillus awamori by a protease inhibitor preparation

Glucoamylase was produced extracellularly by fermentation of strain Aspergillus awamori, which had been genetically modified to have high-level glucoamylase activity. Initial experiments showed that the enzyme deactivated quickly, with a half-life of less than 6 days even stored at 5°C. A possible reason for the rapid deactivation was the presence of proteases, attacking and degrading the glucoamylase. Therefore a liquid protease inhibitor cocktail (Sigma, USA) was selected and applied to enhance the stability of the enzyme. The activity of the enzyme (stored at 5°C) measured by the Schoorl-method with starch as substrate showed that the cocktail was effective with the enzyme maintaining 95% of its initial storage activity for almost one year. The enzyme preparation has been used for starch hydrolysis in a flat-sheet membrane bioreactor at 60°C to manufacture glucose solution and its operation stability extended by using the cocktail.     

Immobilization in the presence of Triton X-100: modifications in activity and thermostability of <Emphasis Type="Italic">Geobacillus thermoleovorans</Emphasis> CCR11 lipase

A partially purified lipase produced by the thermophile Geobacillus thermoleovorans CCR11 was immobilized by adsorption on porous polypropylene (Accurel EP-100) in the presence and absence of 0.1% Triton X-100. Lipase production was induced in a 2.5% high oleic safflower oil medium and the enzyme was partially purified by diafiltration (co. 500,000 Da). Immobilization conditions were established at 25 °C, pH 6, and a protein concentration of 0.9 mg/mL in the presence and absence of 0.1% Triton X-100. Immobilization increased enzyme thermostability but there was no change in neither the optimum pH nor in pH resistance irrelevant to the presence of the detergent during immobilization. Immobilization with or without Triton X-100 allowed the reuse of the lipase preparation for 11 and 8 cycles, respectively. There was a significant difference between residual activity of immobilized and soluble enzyme after 36 days of storage at 4 °C (P < 0.05). With respect to chain length specificity, the immobilized lipase showed less activity over short chain esters than the soluble lipase. The immobilized lipase showed good resistance to desorption with phosphate buffer and NaCl; minor loses with detergents were observed (less than 50% with Triton X-100 and Tween-80), but activity was completely lost with SDS. Immobilization of G. thermoleovorans CCR11 lipase in porous polypropylene is a simple and easy method to obtain a biocatalyst with increased stability, improved performance, with the possibility for re-use, and therefore an interesting potential use in commercial conditions.     

Allosteric serine hydroxymethyltransferase from monkey liver: Temperature induced conformational transitions

The homogeneous serine hydroxymethyltransferase from monkey liver was optimally activate at 60°C and the Arrhenius plot for the enzyme was nonlinear with a break at 15°C. The monkey liver enzyme showed high thermal stability of 62°C, as monitored by circular dichroism at 222 nm, absorbance at 280 nm and enzyme activity. The enzyme exhibited a sharp co-operative thermal transition in the range of 50°–70°(T _m= 65°C), as monitored by circular dichroism. L-Serine protected the enzyme against both thermal inactivation and thermal disruption of the secondary structure. The homotropic interactions of tetrahydrofolate with the enzyme was abolished at high temperatures (at 70°C, the Hill coefficient value was 1.0). A plot ofh values vs. assay temperature of tetrahydrofolate saturation experiments, showed the presence of an intermediate conformer with anh value of 1.7 in the temperature range of 45°–60°C. Inclusion of a heat denaturation step in the scheme employed for the purification of serine hydroxymethyltransferase resulted in the loss of cooperative interactions with tetrahydrofolate. The temperature effects on the serine hydroxylmethyltransferase, reported for the first time, lead to a better understanding of the heat induced alterations in conformation and activity for this oligomeric protein.     

Decay of the 4a-hydroxy-FAD intermediate of phenol hydroxylase

The oxidative half-reaction of phenol hydroxylase involves the formation of three spectrally distinct intermediates (Detmer, K.M., and Massey, V. (1985) J. Biol. Chem. 260, 5998-6005). Addition of an aerobic NADPH-regenerating system, phenol, and azide quantitatively converted oxidized enzyme to the third intermediate, a 4a-hydroxy-FAD species (Detmer, K.M., and Massey, V. (1984) J. Biol. Chem. 259, 11265-11272). This intermediate was isolated in the presence of azide and a wide variety of phenolic ligands. Decay rates were followed for the dehydration of 4a-hydroxy-FAD enzyme resulting in the original oxidized form. Deviation from the rate observed in the absence of phenolic ligands was presumed to be indicative of a binding interaction. Several phenols displayed further stabilization of the 4a-hydroxyflavin species. These ligands exhibited saturation kinetics with respect to the decay half-lives, consistent with a mechanistic model in which both free and bound 4a-hydroxy-FAD enzyme may be directly dehydrated to produce the oxidized species. The lack of stabilization by catechol, the natural product, suggests that product is released from the enzyme during turnover by the time that this intermediate is formed. A pH profile, generated for the decay rates in the absence and presence of phenolic ligand, suggests both acid and base catalysis by hydronium ion and hydroxide, respectively.     

Fungus fruit body lytic enzyme from a myxomycete,Badhamia utricularis

Chitinase,β-1,3-glucanase, cellulase, xylanase and protease activity were detected in a crude enzyme preparation obtained from a slime mold (Badhamia utricularis) which was grown on autoclaved mycelia ofPholiota nameko in a petri dish. The optimal pH of the enzyme preparation for lytic activity against fruit bodies ofLentinus edodes was 4.0, and those ofβ-1,3-glucanase and cellulase were the same. On the other hand, chitinase and protease showed optimal activity at pH 5.0 and 8.0, respectively. The lytic activity was stable below 40°C but completely inactivated at 70°C, and was most stable at pH 5.0. The studies of the optimal pH, thermal stability, and pH stability, and isoelectric focusing analysis of the enzyme preparation suggest that chitinase,β-1,3-glucanase and cellulase activities may be responsible for lysis of fruit bodies of some mushrooms. The crude enzyme preparation from the slime mold lysed fruit bodies of several mushrooms more efficiently than did commercial lytic enzymes preparations (Driselase and Usukizyme).