Pyrolytic characteristics of biomass acid hydrolysis residue rich in lignin

Pyrolytic characteristics of acid hydrolysis residue (AHR) of corncob and pinewood (CAHR, WAHR) were investigated using a thermo-gravimetric analyzer (TGA) and a self-designed pyrolysis apparatus. Gasification reactivity of CAHR char was then examined using TGA and X-ray diffractometer. Result of TGA showed that thermal degradation curves of AHR descended smoothly along with temperature increasing from 150 °C to 850 °C, while a “sharp mass loss stage” for original biomass feedstock (OBF) was observed. Char yield from AHR (42.64-30.35 wt.%) was found to be much greater than that from OBF (26.4-19.15 wt.%). In addition, gasification reactivity of CAHR char was lower than that of corncob char, and there was big difference in micro-crystallite structure. It was also found that CAHR char reactivity decreased with pyrolysis temperature, but increased with pyrolysis heating rate and gasification temperature at 850-950 °C. Furthermore, CAHR char reactivity performed better under steam atmosphere than under CO₂ atmosphere.     

Effects of metal catalysts on CO2 gasification reactivity of biomass char

The effects of five metal catalysts (K, Na, Ca, Mg, and Fe) on CO₂ gasification reactivity of fir char were studied using thermal gravimetric analysis. The degree of carbonization, crystal structure and morphology of char samples was characterized by X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The CO₂ gasification reactivity of fir char was improved through the addition of metal catalysts, in the order K>Na>Ca>Fe>Mg. XRD analysis indicated that Na and Ca improved the formation of crystal structure, and that Mg enhanced the degree of carbon structure ordering. SEM analysis showed that spotted activation centers were distributed on the surface of char samples impregnated with catalysts. Moreover, a loose flake structure was observed on the surface of both K-char and Na-char. Finally, the kinetic parameters of CO₂ gasification of char samples were calculated mathematically.     

Tar reduction in pyrolysis vapours from biomass over a hot char bed

The behaviour of pyrolysis vapours over char was investigated in order to maximise tar conversion for the development of a new fixed bed gasifier. Wood samples were decomposed at a typical pyrolysis temperature (500 °C) and the pyrolysis vapours were then passed directly through a tar cracking zone in a tubular reactor. The product yields and properties of the condensable phases and non-condensable gases were studied for different bed lengths of char (0–450 mm), temperatures (500–800 °C), particle sizes (10 and 15 mm) and nitrogen purge rates (1.84–14.70 mm/s). The carbon in the condensable phases showed about 66% reduction by a 300 mm long char section at 800 °C, compared to that for pyrolysis at 500 °C. The amount of heavy condensable phase decreased with increasing temperature from about 18.4 wt% of the biomass input at 500 °C to 8.0 wt% at 800 °C, forming CO, H₂ and other light molecules. The main mode of tar conversion was found to be in the vapour phase when compared to the results without the presence of char. The composition of the heavy condensable phase was simplified into much fewer secondary and tertiary tar components at 800 °C. Additional measures were required to maximise the heterogeneous effect of char for tar reduction.     

Thermal analysis and devolatilization kinetics of cotton stalk, sugar cane bagasse and shea meal under nitrogen and air atmospheres

Thermal degradation, reactivity and kinetics for biomass materials cotton stalk (CS), sugarcane bagasse 1 (SB1), sugarcane bagasse 2 (SB2) and shea meal (SM) have been evaluated under pyrolysis (N(2)) and oxidising (dry air) conditions, using a non-isothermal thermogravimetric method (TGA). In the cases of CS and SB1 the peak temperatures were 51 degrees C higher for pyrolysis compared with oxidative degradation, whereas for SB2 and SM the difference was approximately 38 degrees C. However, the differences in the rates of weight loss were significantly higher under oxidising conditions for all the materials studied. Maximum rate of weight loss (%s(-1)) under pyrolysis conditions ranged from 0.10 to 0.18 whereas these values accelerated to the range of 0.19-0.28 under oxidising conditions, corresponding to respective peak temperatures. Samples ranked in order of reactivity (R(M)x10(3)) (%s(-1) degrees C(-1)) are CS=1.31 approximately SM=1.30>SB2=1.14>SB1=0.94 for air and CS=0.54>SB2=0.49>SB1=0.45>SM=0.31 for nitrogen. Shea meal exhibited a complex char combustion behaviour indicating that there may be two distinct types of char derived from fibrous and woody components in the original material. Activation energy calculations were based on the Arrhenius correlation.     

Microwave induced pyrolysis of oil palm biomass

The purpose of this paper was to carry out microwave induced pyrolysis of oil palm biomass (shell and fibers) with the help of char as microwave absorber (MA). Rapid heating and yield of microwave pyrolysis products such as bio-oil, char, and gas was found to depend on the ratio of biomass to microwave absorber. Temperature profiles revealed the heating characteristics of the biomass materials which can rapidly heat-up to high temperature within seconds in presence of MA. Some characterization of pyrolysis products was also presented. The advantage of this technique includes substantial reduction in consumption of energy, time and cost in order to produce bio-oil from biomass materials. Large biomass particle size can be used directly in microwave heating, thus saving grinding as well as moisture removal cost. A synergistic effect was found in using MA with oil palm biomass.     

Endophytic Fungal Strains of Soybean for Lipid Production

Lipids created via microbial biosynthesis are a potential raw material to replace plant-based oil for biodiesel production. Oleaginous microbial species currently available are capable of accumulating high amount of lipids in their cell biomass, but rarely can directly utilize lignocellulosic biomass as substrates. Thus this research focused on the screening and selection of new fungal strains that generate both lipids and hydrolytic enzymes. To search for oleaginous fungal strains in the soybean plant, endophytic fungi and fungi close to the plant roots were studied as a microbial source. Among 33 endophytic fungal isolates screened from the soybean plant, 13 have high lipid content (>20 % dry biomass weight); among 38 fungal isolates screened from the soil surrounding the soybean roots, 14 have high lipid content. Also, five fungal isolates with both high lipid content and promising biomass production were selected for further studies on their cell growth, oil accumulation, lipid content and profile, utilization of various carbon sources, and cellulase production. The results indicate that most strains could utilize different types of carbon sources and some strains accumulated >40 % of the lipids based on the dry cell biomass weight. Among these promising strains, some Fusarium strains specifically showed considerable production of cellulase, which offers great potential for biodiesel production by directly utilizing inexpensive lignocellulosic material as feedstock.     

Effects of Pyrolysis Temperature on Product Yields and Energy Recovery from Co-Feeding of Cotton Gin Trash,Cow Manure,and Microalgae: A Simulation Study

The intensive search of new and cleaner energy catches interest in recent years due to huge consumption of fossil fuels coupled with the challenge of energy and environmental sustainability. Production of renewable and environmentally benign energy from locally available raw materials is coming in the frontline. In this work, conversion of the combined biomass (cotton gin trash, cow manure, and Microalgae [Nannochloropsis oculata]) through batch pyrolysis has been investigated. The effect of temperature to the production of energy fuels such as bio-oil, char, and biogas have been simulated considering the yield and energy content as responses. Result of the investigation generally revealed that the proportions of the different biomass did not significantly affect the product yield and energy recovery. Significant effect of temperature is evident in the simulation result of energy recovery whereby maximum conversion was achieved at 400°C for char (91 wt%), 600°C for syngas (22 wt%), and 551°C for bio-oil (48 wt%). Overall energy conversion efficiency of 75.5% was obtained at 589°C in which 15.6 MJ/kg of mixed biomass will be elevated to pyrolysis products.     

Evaluation of pyrolysis chars derived from marine macroalgae silage as soil amendments

Pyrolysis char residues from ensiled macroalgae were examined to determine their potential as growth promoters on germinating and transplanted seedlings. Macroalgae was harvested in May, July and August from beach collections, containing predominantly Laminaria digitata and Laminaria hyperborea; naturally seeded mussel lines dominated by Saccharina latissima; and lines seeded with cultivated L. digitata. Material was ensiled, pressed to pellets and underwent pyrolysis using a thermo‐catalytic reforming (TCR) process, with and without additional steam. The chars generated were then assessed through proximate and ultimate analysis. Seasonal changes had the prevalent impact on char composition, though using mixed beach‐harvested material gave a greater variability in elements than when using the offshore collections. Applying the char at 5% (v/v)/2% (w/w) into germination or seedling soils was universally negative for the plants, inhibiting or delaying all parameters assessed with no clear advantage in harvesting date, species or TCR processing methodology. In germinating lettuce seeds, soil containing the pyrolysis chars caused a longer germination time, poorer germination, fewer true leaves to be produced, a lower average plant health score and a lower final biomass yield. For transplanted ryegrass seedlings, there were lower plant survival rates, with surviving plants producing fewer leaves and tillers, lower biomass yields when cut and less regrowth after cutting. As water from the char‐contained plant pots inhibited the lettuce char control, one further observation was that run‐off water from the pyrolysis char released compounds which detrimentally affected cultivated plant growth. This study clearly shows that pyrolysed macroalgae char does not fit the standard assumption that chars can be used as soil amendments at 2% (w/w) addition levels. As the bioeconomy expands in the future, the end use of residues and wastes from bioprocessing will become a genuine global issue, requiring consideration and demonstration rather than hypothesized use.     

Dwarfs and cannibals in the Arctic: production of Arctic char (Salvelinus alpinus (L.)) at two trophic levels

Due to extensive cannibalism, Arctic char (Salvelinus alpinus (L.)) often represent the two highest trophic levels in Arctic freshwater ecosystem where Arctic char often is the only freshwater fish present. There is a general lack of char stock size and production estimates from Arctic lakes although high catchability and late maturation of large piscivorous individuals raise considerable management challenges because large growing forms are a valued resource. Here, we use mark-recapture to estimate the biomass of both invertebrate feeding dwarfs (60–150 mm) and their cannibalistic conspecifics (>150 mm) in a small Arctic lake at Bear Island (74.5°N, 19.0°E; 11.3 ha; mean depth 1.8 m). Biomass was 10.1 and 2.0 kg ha⁻¹ and production was 2.1 and 0.5 kg ha⁻¹ yr⁻¹ for dwarfs and cannibals, respectively. All the production of invertebrate feeding small char was removed by the cannibals. The low production of the Arctic lake ecosystems combined with high catchability of large piscivorous char indicates that these stocks may be particularly vulnerable to exploitation. We finally point out the similarity between Arctic and sub-arctic alpine populations of Arctic char in production and life-history parameters.     

Bcl-xL increases mitochondrial fission,fusion, and biomass in neurons

Mitochondrial fission and fusion are linked to synaptic activity in healthy neurons and are implicated in the regulation of apoptotic cell death in many cell types. We developed fluorescence microscopy and computational strategies to directly measure mitochondrial fission and fusion frequencies and their effects on mitochondrial morphology in cultured neurons. We found that the rate of fission exceeds the rate of fusion in healthy neuronal processes, and, therefore, the fission/fusion ratio alone is insufficient to explain mitochondrial morphology at steady state. This imbalance between fission and fusion is compensated by growth of mitochondrial organelles. Bcl-x_L increases the rates of both fusion and fission, but more important for explaining the longer organelle morphology induced by Bcl-x_L is its ability to increase mitochondrial biomass. Deficits in these Bcl-x_L–dependent mechanisms may be critical in neuronal dysfunction during the earliest phases of neurodegeneration, long before commitment to cell death.     

The Impact of Hydrothermal and Dilute Acid Pretreatments and Inorganic Metals on Thermal Decomposition of Agricultural Residues and Agricultural Residue Ash Properties

The impacts of hydrothermal and dilute acid pretreatments and alkali and alkaline earth metals (AAEMs) on the thermal degradation of biomass were studied. Besides, the influence of these pretreatments on the biomass ash properties was investigated. The influence of pretreatments on the biomass thermal degradation was manifested in the removal of potassium out of the biomass. The presence of potassium in the biomass catalyzed cellulose thermal degradation and increased the char percentage at temperatures higher than 380 °C. Pretreatments were effective at removing the potassium from biomass and dramatically reduced the char percentage at temperatures higher than 380 °C. It was found that the best burning temperature for biomass ash production was 500 °C because at this temperature the thermal degradation of biomass was completed under pure combustion. It was shown that when burning biomass in oxygen-limited environments, removing AAEMs, particularly potassium, will improve the quality of ash as a potential candidate for supplementary cementitious materials for concrete application.     

Relations between production and biomass of phytoplankton in four Swedish lakes of different trophic status and humic content

Production and biomass values from phytoplankton populations in four different Swedish lakes were analysed. The production in all lakes was directly proportional to biomass during homothermal periods. When the lakes were stratified there was a strong negative relation between specific growth rate and biomass. The data fitted to a logistic density dependent growth equation of the form: dB/ dt = µ_mB(1-B · K^–1) where B is the biomass, µ_m the maximum specific growth rate and K the carrying capacity. The equation was used to derive the parameters µ · µ_m ^–1 and carrying capacity (the maximum possible biomass). These parameters were then discussed in relation to light climate, phosphorus concentration and humic content.     

Intracellular Biosynthesis and Removal of Copper Nanoparticles by Dead Biomass of Yeast Isolated from the Wastewater of a Mine in the Brazilian Amazonia

In this study was developed a natural process using a biological system for the biosynthesis of nanoparticles (NPs) and possible removal of copper from wastewater by dead biomass of the yeast Rhodotorula mucilaginosa. Dead and live biomass of Rhodotorula mucilaginosa was used to analyze the equilibrium and kinetics of copper biosorption by the yeast in function of the initial metal concentration, contact time, pH, temperature, agitation and inoculum volume. Dead biomass exhibited the highest biosorption capacity of copper, 26.2 mg g⁻¹, which was achieved within 60 min of contact, at pH 5.0, temperature of 30°C, and agitation speed of 150 rpm. The equilibrium data were best described by the Langmuir isotherm and Kinetic analysis indicated a pseudo-second-order model. The average size, morphology and location of NPs biosynthesized by the yeast were determined by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and transmission electron microscopy (TEM). The shape of the intracellularly synthesized NPs was mainly spherical, with an average size of 10.5 nm. The X-ray photoelectron spectroscopy (XPS) analysis of the copper NPs confirmed the formation of metallic copper. The dead biomass of Rhodotorula mucilaginosa may be considered an efficiently bioprocess, being fast and low-cost to production of copper nanoparticles and also a probably nano-adsorbent of this metal ion in wastewater in bioremediation process.     

Biotransformation of HCFC-22, HCFC-142b,HCFC-123, and HFC-134a by methanotrophic mixed culture MM1

This research investigated the potential for methanotrophic biotransformation of three HCFCs — chlorodifluoromethane (HCFC-22); 1-chloro-1,1-difluoroethane (HCFC-142b); and 1,1-dichloro-2,2,2-trifluoroethane (HCFC-123); and one HFC — 1,2,2,2-tetrafluoroethane (HFC-134a). All of these compounds were biotransformed to differing degrees by methanotrophic mixed culture MM1. Rates of transformation were obtained by monitoring disappearance of the target compounds from the headspace in batch experiments. Henry's constants were determined over a range of conditions to enable estimation of the intrinsic rates of transformation. Intrinsic rates of transformation were obtained by combining a second order rate expression with an expression describing loss of transformation activity due to either endogenous decay or product toxicity. For HCFC-123 and HFC-134a, the independently measured endogenous decay rate for mixed culture MM1 (0.594/day) was sufficient to account for the observed loss of transformation activity with time. However, the endogenous decay rate did not account for the loss of transformation activity for HCFC-22 and HCFC-142b. A model based on product toxicity provided a reasonable representation of the loss of transformation activity for these compounds. The order of reactivity was HCFC-22>HCFC-142b>HFC-134a>HCFC-123, with second order rate coefficients of 0.014, 0.0096, 0.00091, and 0.00054 l/mg-day, respectively. Transformation capacities for HCFC-22 and HCFC-142b were 2.47 and 1.11 µg substrate/mg biomass, respectively.     

固定化小球藻产氧及光合速率的研究

通过对固定化小球藻产氧及光合速率的研究,进一步解决水产养殖水体溶解氧不足的问题,为生物增氧技术投入使用奠定基础.固定化具有较高的生物量及生物活性,在研究中被广泛使用.运用固定化技术对固定化小球藻产氧及光合速率进行了研究,结果表明,固定化小球藻具有较好的生物量及生物活性,海藻酸钠+羧甲基纤维素钠+硅藻土作为固定化基质有利...     

A combined ultrastructural approach to the study of nuclear matrix thermal stabilization

Summary Using mouse erythroleukaemia cells and different ultrastructural techniques, the morphology was investigated of the nuclear matrix obtained after incubation at 37° C of isolated nuclei. If purified nuclei were heated for 45 min at 37° C, the final matrix exhibited well-recognizable nucleolar remnants, an inner network and a peripheral lamina. Without such incubation only the peripheral lamina was seen surrounding homogeneous, finely granular material. Similar results were obtained with both araldite-embedded and freeze-fractured nuclear matrices, although in the latter case the loose granular material was not evident. Observations of araldite-embedded, heat-treated nuclei revealed clumping of heterochromatin in small, very electron-dense masses with large interchromatin spaces. These ultrastructural aspects were even more striking in freeze-fractured nuclei. Cytochemical matrix analysis by osmium-ammine staining for nucleic acids and DNase-gold labelling for DNA localization demonstrated that also matrix residual nucleic acids, mostly RNA, are stabilized by heat exposure of isolated nuclei. The results demonstrate that the morphology of heat-stabilized nuclear matrix is not artefactually affected during the preparation for conventional electron microscopy and suggest a possible involvement of nucleic acids in the heat-induced stabilization of the nuclear matrix.     

Influence of manure types and pyrolysis conditions on the oxidation behavior of manure char

Livestock manure can be quickly converted into valuable products (H₂, syn-gas and char) by low temperature gasification. Manure char combustion offers energy for the gasification reactions. In the paper, the influence of manure type and pyrolysis conditions on manure char reactivity is addressed. The results show that the oxidation behaviors of manure char are dependent strongly on manure type and pyrolysis conditions employed. The large difference between the oxidation behaviors of pig and hen manure chars can be attributed to the difference in the organic materials and minerals of the samples. High final temperature, flash pyrolysis and water steam atmosphere used for char preparation promote the resultant char reactivity.     

Directed differentiation of embryonic P19 cells and neural stem cells into neural lineage on conducting PEDOT–PEG and ITO glass substrates

Differentiation of pluripotent and lineage restricted stem cells such as neural stem cells (NSCs) was studied on conducting substrates of various nature without perturbation of the genome with exogenous genetic material or chemical stimuli. Primary mouse adult neural stem cells (NSCs) and P19 pluripotent embryonal (P19 EC) carcinoma cells were used. Expression levels of neuronal markers β-III-tubulin and neurofilament were evaluated by immunochemistry and flow cytometry. It was shown that the ability of the substrate to induce differentiation directly correlated with its conductivity. Conducting substrates (conducting oxides or doped π-conjugated organic polymers) with different morphology, structure, and conductivity mechanisms all promoted differentiation of NSC and P19 cells into neuronal lineage to a similar degree without use of additional factors such as poly-l-ornithine coating or retinoic acid, as verified by their morphology and upregulation of the neuronal markers but not astrocyte marker GFAP. However, substrates with low conductance below ca. 10^?4 S cm^?2 did not show this ability. Morphology of differentiating cells was visualized by atomic force microscopy. NSCs cells increased β-III-tubulin expression by 95% and P19 cells by over 30%. Our results suggest that the substrate conductivity is a key factor governing the cell fate. Differentiation of P19 cells into neuronal lineage on conducting substrates was attributed to downregualtion of Akt signaling pathway and increase in expression of dual oxidase 1 (DUOX 1).     

Influence of mold growth on the pressure drop in aerated solid state fermentors

The measurement of pressure drop(DeltaP) across an aerated fermentation bed is proposed as alternative on-line sensor for the qualitative and, in some cases, quantitative, macroscopic changes in a static solid state fermentor. An increase in the DeltaP is correlated with the evolution of the different phases of Aspergillus niger growth: germination, vegetative growth, limitation, and sporulation, we observed in the microscope. For the case where the support is not modified during the fermentation and the water content remains constant, i.e., a synthetic resin (Amberlite IRA-900), the gas phase permeability of the bed is directly related to the biomass content. For example, the permeability of the bed is reduced to 5% of the initial value when biomass attains 21 mg dry biomass/g dry support. Biomass was appropriately predicted from the DeltaP measurements in an independent test. Experiments with different initial sucrose solution concentrations showed that biomass could not be produced beyond a certain level (21.5 mg dry biomass/g dry support) which suggests steric limitations. For the case of wheat bran and cane bagasse, the increase in DeltaP was related qualitatively to the evolution in the growth and the morphology of the mold . (c) 1993 Wiley & Sons, Inc.     

The neurite-promoting domain of human laminin promotes attachment and induces characteristic morphology in non-neuronal cells

The interaction of cells with laminin and laminin fragments was studied in short-term cell attachment assays. Neurite-promoting chymotrypsin fragments of laminin were isolated using a monoclonal antibody which blocks neurite outgrowth on laminin. The fragments were shown, by electron microscopy after rotary shadowing and by immunological reactivity with different monoclonal antibodies, to contain only the distal end of the long arm. These fragments promoted the attachment and spreading of glioma, sarcoma, carcinoma, muscle, and endodermal cells to the same extent as intact laminin. The attachment was unaffected by peptides containing the RGD sequence. The morphology of the cells on the chymotrypsin fragments was indistinguishable from that on intact laminin but different from the morphology of the same cells on fibronectin. Light microscopy and scanning electron microscopy showed extensive process formation on laminin but not on fibronectin suggestive of increased cell motility in response to laminin. We conclude that the neurite-promoting domain of laminin contains a major site of interaction for non-neuronal cells and that this site induces a cellular response in certain non-neuronal cells that is unique to laminin.