Effects of media composition on substrate removal by pure and mixed bacterial cultures

Continuous culture experiments with identical experimental designs were run with a mixed microbial community of activated sludge origin and an axenic bacterial culture derived from it. Each culture received 2-chlorophenol (2-CP) at a concentration of 160 mg/L as COD and L-lysine at a concentration of 65 mg/L as COD. A factorial experimental design was employed with dilution rate and media composition as the two controlled variables. Three dilution rates were studied: 0.015, 0.0325, and 0.05 h^–1. Media composition was changed by adding four biogenic compounds (butyric acid, thymine, glutamic acid and lactose) in equal COD proportions at total concentrations of 0, 34, 225, and 1462 mg/L as COD. The measured variables were the effluent concentrations of 2-CP as measured by the 4-aminoantipyrene test and lysine as measured by the o-diacetylbenzene procedure. The results suggest that community structure and substrate composition play important roles in the response of a microbial community to mixed substrates. The addition of more biogenic substrates to the axenic culture had a deleterious effect on the removal of both lysine and 2-CP, although the effect was much larger on lysine removal. In contrast, additional substrates had a positive effect on the removal of 2-CP by the mixed community and much less of a negative effect on the removal of lysine. The dilution rate at which the cultures were growing had relatively little impact on the responses to the additional substrates.Abbreviations COD chemical oxygen demand - 2-CP 2-chlorophenol - DOC dissolved organic carbon - MDL method detection limit - SS suspended solids     

para-Chlorophenol inhibition on COD, nitrogen and phosphate removal from synthetic wastewater in a sequencing batch reactor

COD, nitrogen, phosphate and para-chlorophenol (4-chlorophenol, 4-CP) removal from synthetic wastewater was investigated using a four-step sequencing batch reactor (SBR) at different sludge ages and initial para-chlorophenol (4-CP) concentrations. The nutrient removal process consisted of anaerobic, oxic, anoxic and oxic phases with hydraulic residence times (HRT) of 1/3/1/1 h and a settling phase of 0.75 h. A Box-Wilson statistical experiment design was used considering the sludge age (5-25 days) and 4-CP concentration (0-400 mg l(-1)) as independent variables. Variations of percent COD, NH4-N, PO4-P and 4-CP removals with sludge age and initial 4-CP concentration were investigated. Percent nutrient removals increased with increasing sludge age and decreasing 4-CP concentrations. Low nutrient removals were obtained at high initial 4-CP concentrations especially at low sludge ages. However, high sludge ages partially overcome the adverse effects of 4-CP and resulted in high nutrient removals. COD, NH4-N, PO4-P and 4-CP removals were 76%, 72%, 26% and 34% at a sludge age of 25 days and initial 4-CP concentration of 200 mg l(-1). Sludge volume index (SVI) also decreased with increasing sludge age and decreasing 4-CP concentrations. An SVI value of 104 ml g(-1) was obtained at a sludge age of 25 days and initial 4-CP of 200 mg l(-1).     

共代谢条件下光合细菌对2-氯苯酚的生物降解

光合细菌PSB-1D不能利用2-氯苯酚(2-CP)作为唯一的碳源和能源.选用苹果酸、丙酸钠、乙酸钠、柠檬酸钠、苯酚、葡萄糖和可溶性淀粉等7种不同碳源作为光合细菌PSB-1D降解2-CP的共代谢基质,考察了在黑暗好氧培养条件下,不同共代谢基质对PSB-1D生长及降解2-CP效果的影响.结果表明:葡萄糖能够很好地促进PSB-1D的大量繁殖,提高降解效果,缩短降解周期,为最佳共代谢基质.对葡萄糖的投加浓度进行了优化,当葡萄糖的投加浓度为3 g·L-1时,菌株PSB-1D培养168 h后的菌体生长浓度△D560为1.749,2-CP的半衰期为3.9 d,降解速率常数为0.00864 h-1.采用SDS-PAGE对微生物全细胞蛋白质进行分析发现,在共代谢过程中当菌株PSB-1D利用葡萄糖作为底物提供能源和碳源时,可诱导产生2-CP特异性降解酶.     

Anaerobic treatment of 2,4,6-trichlorophenol in an expanded granular sludge bed-anaerobic filter (EGSB-AF) bioreactor at 15 degrees C

Expanded granular sludge bed-anaerobic filter (EGSB-AF) bioreactors were operated at 15 degrees C for the treatment of 2,4,6-trichlorophenol (TCP)-containing volatile fatty acid (VFA)-based wastewaters. The seed sludge used as inoculum for the control (no TCP) and test reactor was unexposed to chlorophenols (CPs) prior to the 425-day trial. TCP supplementation to the feed at 50 mg TCPl(-1) partially inhibited the anaerobic degradation of the VFA feed measured as COD removal efficiency. However, the withdrawal and subsequent application of stepwise increments to the TCP loading resulted in steady COD removal. Terminal restriction fragment length polymorphism analysis showed Methanosaeta-like Archaea in the control reactor over the experimental period. Different methanogenic populations were detected in the test reactor and responded to the changes in feed composition. Bacterial community analyses indicated changes in the community structure over time and suggested the presence of Campylobacter-like, Acidimicrobium-like and Heliophilum-like organisms in the samples. TCP mineralisation was by a reductive dechlorination pathway through 2,4-dichlorophenol (DCP) and 4-chlorophenol (4-CP) or 2-chlorophenol (2-CP). CP degradation rates in sludge granules from the lower chamber of the hybrid EGSB-AF reactor was in the order TCP > DCP > 4-CP > 2-CP. However, a biodegradability order of lower CPs > TCP was observed in fixed-film biomass taken from the upper reactor chamber, thus reflecting the role of this reactor section in the metabolism of residual lower CPs from the lower sludge-bed stage of operation.     

Modeling chlorophenols degradation in sequencing batch reactors with instantaneous feed-effect of 2,4-DCP presence on 4-CP degradation kinetics

Two instantaneously fed sequencing batch reactors (SBRs), one receiving 4-chlorophenol (4-CP) (SBR4) only and one receiving mixture of 4-CP and 2,4-dichlorophenol (2,4-DCP) (SBRM), were operated with increasing chlorophenols concentrations in the feed. Complete degradation of chlorophenols and high-Chemical oxygen demand (COD) removal efficiencies were observed throughout the reactors operation. Only a fraction of biomass (competent biomass) was thought to be responsible for the degradation of chlorophenols due to required unique metabolic pathways. Haldane model developed based on competent biomass concentration fitted reasonably well to the experimental data at different feed chlorophenols concentrations. The presence of 2,4-DCP competitively inhibited 4-CP degradation and its degradation began only after complete removal of 2,4-DCP. Based on the experimental results, the 4-CP degrader’s fraction in SBRM was estimated to be higher than that in SBR4 since 2,4-DCP degraders were also capable of degrading 4-CP due to similarity in the degradation pathways of both compounds.     

Packed- and fluidized-bed biofilm reactor performance for anaerobic wastewater treatment

Anaerobic degradation performance of a laboratory-scale packed-bed reactor (PBR) was compared with two fluidized-bed biofilm reactors (FBRs) on molasses and whey feeds. The reactors were operated under constant pH (7) and temperature (35 degrees C) conditions and were well mixed with high recirculation rates. The measured variables were chemical oxygen demand (COD), individual organic acids, gas composition, and gas rates. As carrier, sand of 0.3-0.5 mm diameter was used in the FBR, and porous clay spheres of 6 mm diameter were used in the PBR. Startup of the PBR was achieved with 1-5 day residence times. Start-up of the FBR was only successful if liquid residence times were held low at 2-3 h. COD degradations of 86% with molasses (90% was biodegradable) were reached in both the FBR and PBR at 6 h residence time and loadings of 10 g COD/L day. At higher loadings the FBR gave the best performance; even at 40-45 g COD/L day, with 6 h residence times, 70% COD was degraded. The PBR could not be operated above 20 g COD/L day without clogging. A comparison of the reaction rates show that the PBR and FBR per formed similarly at low concentrations in the reactors up to 1 g COD/L, while above 3 g COD/L the rates were 17.4 g COD/L day for the PBR and 38.4 g COD/L day for the FBR. This difference is probably due to diffusion limitations and a less active biomass content of the PBR compared with the fluidized bed.The results of dynamic step change experiments, in which residence times and feed concentrations were changed hanged at constant loading, demonstrated the rapid response of the reactors. Thus, the response times for an increase in gas rate or an increase in organic acids due to an increase in feed concentration were less than 1 day and could be explained by substrate limitation. Other slower responses were observed in which the reactor culture adapted over periods of 5-10 days; these were apparently growth related. An increase in loading of over 100% always resulted in large increases inorganic acids, especially acetic and propionic, as well as large increases in the CO(2) gas content. In general, the CO(2) content of the gas was very low, due to the large amount of dissolved CO(2) that exited with the liquid phase at low residence times. The performance of the FBR with whey was comparable to its performance with molasses, and switching of molasses to whey feed resulted in immediate good performance without adaptation.     

Influence of dissolved organic matter source on lake bacterioplankton structure and function--implications for seasonal dynamics of community composition

It has been suggested that autochthonous (internally produced) organic carbon and allochthonous (externally produced) organic carbon are utilized by phylogenetically different bacterioplankton. We examined the relationship between the source of organic matter and the structure and function of lake bacterial communities. Differences and seasonal changes in bacterial community composition in two lakes differing in their source of organic matter were followed in relation to environmental variables. We also performed batch culture experiments with amendments of various organic substrates, namely fulvic acids, leachates from algae, and birch and maple leaves. Differences in bacterial community composition between the lakes, analysed by terminal restriction fragment length polymorphism, correlated with variables related to the relative loading of autochthonous and allochthonous carbon (water colour, dissolved organic carbon, nutrients, and pH). Seasonal changes correlated with temperature, chlorophyll and dissolved organic carbon in both lakes. The substrate amendments led to differences in both structure and function, i.e. production, respiration and growth yield, of the bacterial community. In conclusion, our results suggest that the source of organic matter influences community composition both within and among lakes and that there may be a coupling between the structure and function of the bacterial community.     

Effect of carbon sources and shock loading on the removal of chlorophenols in sequential anaerobic-aerobic reactors

The effect of carbon sources and shock loadings have been studied using two sets of sequential upflow anaerobic sludge blanket (UASB) and rotating biological contactor (RBC) reactors viz., UASB-I followed by RBC-I and UASB-II followed by RBC-II for the removal of two different priority pollutants, 2-CP and 2,4-DCP present in simulated wastewaters. Sodium formate, sodium propionate, glucose and methanol were used separately as four different carbon sources in the feed as co-substrate. Methanol was found to be the best carbon source for UASB reactors showing 95% 2-CP and 81.1% 2,4-DCP removals. The carbon sources formate and propionate were not found suitable in UASB reactors as only 22.6-46.8% 2-CP and 41.9-42.8% 2,4-DCP removals were observed. With glucose as carbon source 93.7% 2-CP and 79.6% 2,4-DCP removals were observed in UASB reactors. For all the four carbon sources more than 97.6% 2-CP and 99.7% 2,4-DCP removals were observed in sequential reactors. Although all the four carbon sources could not serve as good carbon source for UASB reactor alone but could be successfully used by the sequential reactors for the removal of chlorophenols. The Performance of sequential reactors was also evaluated at five different chlorophenolic shock loadings. During shock loading study the concentration of chlorophenols in the wastewaters was increased to 45, 60, 75, 90 and 105 mg/l as compared to the normal feed containing 30 mg/l 2-CP or 2,4-DCP. During shock loading study complete removal of 2-CP and more than 99.6% removal of 2,4-DCP was observed in sequential reactors. Sequential reactors successfully withstood all the shock loadings and produced high quality effluents.     

Biological treatment of 2,4-dichlorophenol containing synthetic wastewater using a rotating brush biofilm reactor

A newly developed rotating brush biofilm reactor was used for DCP, COD and toxicity removal from 2,4-dichlorophenol (DCP) containing synthetic wastewater at different feed COD, TCP concentrations and A/Q (biofilm surface area/feed flow rate) ratios. A Box-Wilson statistical experiment design was used by considering the feed DCP (50-500 mg l(-1)), COD (2000-6000 mg l(-1)) and A/Q ratio (73-293 m2 d m(-3)) as the independent variables while percent DCP, COD, and toxicity removals were the objective functions. The experimental data were correlated by a quadratic response function and the coefficients were determined by regression analysis. Percent DCP, COD and toxicity removals calculated from the response functions were in good agreement with the experimental data. DCP, COD and toxicity removals increased with increasing A/Q ratio and decreasing feed DCP concentrations. The optimum A/Q ratio resulting in the highest COD (90%), DCP (100%) and toxicity (100%) removals with the highest feed COD (6000 mg l(-1)) and DCP (500 mg l(-1)) contents was nearly 210 m2 d m(-3).     

Tailor-made olefinic medium-chain-length poly[(R)-3-hydroxyalkanoates] by Pseudomonas putida GPo1: batch versus chemostat production

Functionalized medium-chain-length polyhydroxyalkanoates (mclPHAs) have gained much interest in research on biopolymers because of their ease of chemical modification. Tailored olefinic mclPHA production from mixtures of octanoic acid and 10-undecenoic acid was investigated in batch and dual (C,N) nutrient limited chemostat cultures of Pseudomonas putida GPo1 (ATCC 29347). In a batch culture, where P. putida GPo1 was grown on a mixture of octanoic acid (58 mol%) and 10-undecenoic acid (42 mol%), it was found that the fraction of aliphatic monomers was slightly lower in mclPHA produced during exponential growth than during late stationary phase. Thus, the total monomeric composition changed over time indicating different kinetics for the two carbon substrates. Chemostat experiments showed that the dual (C,N) nutrient limited growth regime (DNLGR) for 10-undecenoic acid coincided with the one for octanoic acid. Five different chemostats on equimolar mixtures of octanoic acid and 10-undecenoic acid within the DNLGR revealed that the monomeric composition of mclPHA was not a function of the carbon to nitrogen (C(0)/N(0)) ratio in the feed medium but rather of the dilution rate. The fraction of aliphatic monomers in the accumulated mclPHA was slightly lower at high dilution rates and increased towards low dilution rates, again indicating different kinetics for the two carbon substrates in P. putida GPo1.     

Aerobic biotreatment of acetone and methanol in a continuous flow bioreactor during unsteady state operation

The responses of a culture, enriched with acetone and methanol as dual carbon energy substrates, when growing in a continuous flow bioreactor are examined with respect to various imposed transient state operating conditions. The transients investigated include both removal from and addition to the process feed of acetone and methanol, step changes in the concentrations of acetone and methanol in the process feed, and step changes in the dilution rates employed. The capacity of the culture to achieve complete acetone oxidation, after step changes, was shown to be suspect, emphasizing the need to base performance criteria for biotreatment process operation on individual key component concentrations rather than on the lumped parameters widely used to describe pollutant loads in aqueous effluents.     

Degradation of 2,4,6-trichlorophenol (2,4,6-TCP) by co-immobilization of anaerobic and aerobic microbial communities in an upflow reactor under air-limited conditions

The co-immobilization and the culture of anaerobic and aerobic communities was tested for the mineralization of 2,4,6-trichlorophenol (2,4,6-TCP). At first, the anaerobic microorganisms (aggregated into granules) were cultivated in an upflow anaerobic sludge blanket (UASB) reactor, in a continuous mode, with glucose, propionate, acetate (COD loading rate = 0.5-2.0 g COD/l per day, ratio 1:1:1) and 2,4,6-TCP (2,4,6-TCP loading rate = 25-278 micromol/l per day) as substrates. 2,4,6-TCP was degraded into 2,4-DCP and 4-CP, but it was not mineralized because of the low degradation rates of 4-CP. Furthermore, the highest loading rates of 2,4,6-TCP (>126 micromol/l per day) caused the inhibition of the strains degrading the propionate. The granules were therefore tested in association with the aerobic community. They were immobilized in kappa-carrageenan/gelatin [2% (w/w) of each polymer] gel beads and cultivated in a reactor, on their own (to test the influence of the gel), and then with the aerobic community, under anaerobic and air-limited conditions, respectively. The results showed that (1) the gel did not influence the activity of the granules, (2) the anaerobic and aerobic communities could be easily co-immobilized in gel beads and cultivated in a reactor, (3) the mineralization of 2,4,6-TCP (2,4,6-TCP loading rate = 10-506 micromol/l per day), its intermediates of degradation and the other substrates [glucose + acetate + propionate (ratio 1:1:1) = COD loading rate = 500 mg COD/l per day] could be obtained under air-limited conditions if the culture parameters were strictly controlled [airflow = 36-48 vvd (volume of air/volume of liquid in the reactor per day), pH value at around 7.5]. Finally, the gel did not retain its structure during the whole culture (263 days) in the air-limited reactor, but the anaerobic and aerobic communities retained their activities and worked together for the mineralization.     

Cultivation of Escherichia coli with mixtures of 3-phenylpropionic acid and glucose: steady-state growth kinetics.

The fate of pollutants in the environment is affected by the presence of easily degradable carbon sources. As a step towards understanding these complex interactions, a model system was explored: the degradation of mixtures of glucose (i.e., an easily degradable substrate) and 3-phenylpropionic acid (3ppa) (a model pollutant) by Escherichia coli ML 30 was studied systematically in carbon-limited continuous culture. The two substrates were always consumed simultaneously regardless of the dilution rate applied. Even at dilution rates higher than the maximum specific growth rate for 3ppa (0.35 +/- 0.05 h-1), the two carbon substrates were utilized together. When cells were grown at a constant dilution rate with different mixtures of 3ppa and glucose, in which 3ppa contributed between 5 and 90% of carbon substrate in the feed medium, the steady-state concentrations of 3ppa and glucose were approximately proportional to the ratio of the two substrates in the feed medium. When cells were cultivated at different dilution rates with a 1:1 mixture (based on carbon) of glucose and 3ppa, an overall maximum specific growth rate of 0.90 +/- 0.05 h-1 and a Monod substrate saturation constant for 3ppa (Ks) of 600 to 700 micrograms liter-1, similar to that measured during growth with 3ppa alone, fitted the experimentally determined steady-state 3ppa concentrations. However, due to the highly differing substrate affinity constants for 3ppa and glucose (Ks approximately 30 to 70 micrograms liter-1), the total steady-state carbon concentration in the culture at a constant dilution rate was determined mainly by the steady-state 3ppa carbon concentration, and it increased with increasing proportions of 3ppa in the feed medium.     

Effects of 2,4-dichlorophenol on activated sludge

The effects of 2,4-dichlorophenol (2,4-DCP) on both acclimated and unacclimated activated sludge were investigated in batch reactors. The IC(50) values on the basis of maximum specific growth rate ( micro(m)), percent chemical oxygen demand (COD) removal efficiency and sludge activity were found to be 72, 60 and 47 mg l(-1), respectively, for unacclimated culture. The percent COD removal efficiencies of unacclimated culture were affected adversely, even at low concentrations, whereas culture acclimated to 75 mg 2,4-DCP l(-1) could tolerate about 200 mg 2,4-DCP l(-1)on the basis of COD removal efficiency. Although yield coefficient values of unacclimated culture increased surprisingly to very high values with the addition of 2,4-DCP, a linear decrease with respect to 2,4-DCP concentrations was observed for acclimated culture. Although no removal was observed with unacclimated culture, almost complete removal of 2,4-DCP up to a concentration of 148.7 mg l(-1) was observed with acclimated culture. It was showed that the culture could use 2,4-DCP as sole organic carbon source, although higher removal efficiencies in the presence of a readily degradable substrate were observed. Culture acclimated to 4-chlorophenol used 2,4-DCP as sole organic carbon source better than those acclimated to 2,4-DCP.     

Theoretical effects of feed composition, feed conversion and feed spillage on waste discharge in fish culture

Based on feed composition, fish composition and feed conversion, some theoretical effects of feeding on waste discharge are calculated to illustrate the appropriateness of farm effluent monitoring. The effects of feed conversion and feed spillage and feed composition on waste discharge (suspended and dissolved N, P & COD) are demonstrated. Slight variations in feed conversion at the moment of sampling, especially those evoked by feed spillage, have tremendous consequences for discharge values. It appears crucial to determine whether observed conversions are explained by inherent efficiencies of fish growth, or whether higher growth efficiencies are combined with feed spillage. Therefore, thorough knowledge of relationships between nutrient intake and growth should be applied to effluent assessment. A calculation is presented to serve as a preliminary assessment of the impacts of these variables on water quality monitoring. The concept is illustrated using measurements from a recirculation pilot eel culture system.     

Model-based optimization of a sequencing batch reactor for biological nitrogen removal

An optimal operating mode for a sequencing batch reactor was determined via a model-based optimization. Synthetic wastewater containing mainly organic matter (as glucose) and nitrogen (as ammonium chloride) was treated without any addition of an external carbon source to accomplish denitrification step. A simplified model was used to describe process dynamics, comprised of six ordinary differential equations and an empirical correlation for oxygen consumption rate. Batch cycle time was the chosen objective function to be minimized for a fixed volume of waste to be treated. Furthermore, as SBR operation is divided in two major phases - aerobic and anoxic, to achieve total pollutants removal within minimum time, these phases can be repeatedly alternated. To ensure availability of organic matter necessary for denitrification, these two phases were combined with feed steps. Different feed strategies were tested using one, two or three feed steps. A successive quadratic programming algorithm was used, and maximum values for final COD, nitrate and ammonium concentrations, as well as maximum feed pump flow rate were some the process constraints. One step feed strategy was indicated by the optimization leading to a batch cycle time of 5h.     

Biodegradation of 4-chlorophenol by <Emphasis Type="Italic">Arthrobacter chlorophenolicus A6</Emphasis>: effect of culture conditions and degradation kinetics

Among known microbial species, Arthrobacter chlorophenolicus A6 has shown very good potential to treat phenolic wastewaters. In this study, the levels of various culture conditions, namely initial pH, agitation (rpm), temperature (°C), and inoculum age (h) were optimized to enhance 4-chlorophenol (4-CP) biodegradation and the culture specific growth rate. For optimization, central composite design of experiments followed by response surface methodology (RSM) was applied. Results showed that among the four independent variables, i.e., pH, agitation (rpm), temperature (°C), and inoculum age (h) investigated in this study, interaction effect between agitation and inoculum age as well as that between agitation and temperature were significant on both 4-CP biodegradation efficiency and culture specific growth rate. Also, at the RSM optimized settings of 7.5 pH, 207 rpm, 29.6°C and 39.5 h inoculum age, 100% biodegradation of 4-CP at a high initial concentration of 300 mg l⁻¹ was achieved within a short span of 18.5 h of culture. The enhancement in the 4-CP biodegradation efficiency was found to be 23% higher than that obtained at the unoptimized settings of the culture conditions. Results of batch growth kinetics of A. chlorophenolicus A6 for various 4-CP initial concentrations revealed that the culture followed substrate inhibition kinetics. Biokinetic constants involved in the process were estimated by fitting the experimental data to several models available from the literature.     

Application of mass and energy balance regularities to product formation

Material and energy balances for fermentation processes with product formation are developed using regularities which are frequently useful in analyzing experimental results. Available electron balances are presented and used to analyze the results of experiments in which biomass and lysine are produced in batch culture using molasses and corn extract as organic substrates. Measured values of biomass productivity, lysine productivity, O₂ consumption rate, heat evolution rate, CO₂ evolution rate, and rate of utilization of reducing sugars (RS) are used to obtain estimates of biomass energetic yield, lysine energetic yield, and fraction of substrate energy evolved as heat. For two of the three experiments, based on the entire fermentation, the measured mass rate variables are very consistent and energy measurement errors are less than 10% when proper consideration is given to both the RS and the amino acids present in the organic substrate. The average measured value of 26.5 kcal/equivalent (equiv) of available electrons transferred to oxygen compares favorably with the known average value of 27 kcal/equiv.     

Cometabolic biodegradation of 4-chlorophenol by sequencing batch reactors at different temperatures

The simultaneous removal of 4-chlorophenol (4-CP) and phenol in lab-scale sequencing batch reactors at different temperatures has been studied. Phenol feed concentration was fixed at 525 mg/L and 4-CP concentration was increased from 105 to 2100 mg/L at a constant hydraulic residence time (HRT) of 10.5 d. Complete phenol and 4-CP biodegradation was achieved during the aerobic stage working with 4-CP concentrations up to 1470 mg/L in the feed. Both 4-CP and phenol specific initial removal rates were strongly affected by 4-CP feed concentration and temperature. Only at the highest temperature tested (35 °C) it was possible to increase the maximum assimilative 4-CP concentration by the biological sludge up to 2100 mg/L, and a significant reduction of the ecotoxicity of the effluents was observed. 4-chlorocatechol (4-CC) was identified as the major intermediate in the aerobic cometabolic 4-CP degradation, being the ecotoxicity of that species substantially lower than that of 4-CP.     

Degradation of 4-chlorophenol in UASB reactor under methanogenic conditions

Treatment of simulated wastewater containing 40 mg/l of 4-chlorophenol (4-CP) was carried out in an upflow anaerobic sludge blanket (UASB) reactor under methanogenic condition. The performance of this test UASB reactor was evaluated in terms of 4-CP removal. Hydraulic retention time (HRT) and substrate:co-substrate ratio for the 4-CP removal was optimized by varying the influent flow rate (13-34.7 ml/min) and sodium acetate concentration (2-5 g/l), respectively. A control UASB reactor, which was not exposed to 4-CP was also operated under similar conditions. Organic loading rate (OLR) was varied in the range of 2-5.3 kg/m(3)/d and 1.7-4.2 kg/m(3)/d, respectively, for HRT and substrate:co-substrate ratio studies, respectively. The optimum HRT and substrate:co-substrate ratio for the removal of 4-CP was 12h and 1:75, respectively. Removal of 4-CP achieved at optimum HRT and substrate:co-substrate ratio was 88.3+/-0.7%. Removal of 4-CP occurred through dehalogenation and caused increase in chloride ion concentration in the effluent by 0.23-0.27 mg/mg 4-CP removed. The ring cleavage test showed the ortho mode of ring cleavage of 4-CP. Change in the elemental composition of the anaerobic biomass of UASB reactors was observed during the study period. Concentration of Ca(2+) increased in the biomass and this could be attributed to the biosoftening. Specific methanogenic activity of the sludge of control and test UASB reactor was 0.832 g CH(4) COD/g VSS d and 0.694 g CH(4) COD/g VSS d, respectively.