Optimum conditions for the biological production of lactic acid by a newly isolated lactic acid bacterium,Lactobacillus sp. RKY2

Lactic acid is a green chemical that can be used as a raw material for biodegradable polymer. To produce lactic acid through microbial fermentation, we previously screened a novel lactic acid bacterium. In this work, we optimized lactic acid fermentation using a newly isolated and homofermentative lactic acid bacterium. The optimum medium components were found to be glucose, yeast extract, (NH₄)₂HPO₄, and MnSO₄. The optimum pH and temperature for a batch culture ofLactobacillus sp. RKY2 was found to be 6.0 and 36°C, respectively. Under the optimized culture conditions, the maximum lactic acid concentration (153.9 g/L) was obtained from 200 g/L of glucose and 15 g/L of yeast extract, and maximum lactic acid productivity (6.21 gL⁻¹h⁻¹) was obtained from 100 g/L of glucose and 20 g/L of yeast extract. In all cases, the lactic acid yields were found to be above 0.91 g/g. This article provides the optimized conditions for a batch culture ofLactobacillus sp. RKY2, which resulted in highest productivity of lactic acid.     

Optimisation of media and cultivation conditions for L(+)(S)-lactic acid production by Lactobacillus casei NRRL B-441

Process variables and concentration of carbon in media were optimised for lactic acid production by Lactobacillus casei NRRL B-441. Lactic acid yield was inversely proportional to initial glucose concentration within the experimental area (80-160 g l(-1)). The highest lactic acid concentration in batch fermentation, 118.6 g l(-1), was obtained with 160 g 1(-1) glucose. The maximum volumetric productivity, 4.4 g 1(-1) h(-1) at 15 h, was achieved at an initial glucose concentration of 100 g l(-1). Similar lactic acid concentrations were reached with a fedbatch approach using growing cells, in which case the fermentation time was much shorter. Statistical experimental design and response surface methodology were used for optimising the process variables. The temperature and pH optima for lactic acid production were 35 degrees C, pH 6.3. Malt sprout extract supplemented with yeast extract (4 g l(-1)) appeared to be an economical alternative to yeast extract alone (22 g l(-1)) although the fermentation time was a little longer. The results demonstrated both the separation of the growth and lactic acid production phases and lactic acid production by non-growing cells without any nutrient supplements. Resting L. casei cells converted 120 g l(-1) glucose to lactic acid with 100% yield and a maximum volumetric productivity of 3.5 g l(-1) h(-1).     

Production of lactic acid from wastepaper as a cellulosic feedstock

Lactic acid promises to be an important commodity chemical in the future as a monomer for the production of biodegradable polylactic acid (PLA). As the demand for lactic acid increases, the need to explore alternative feedstock sources and process options that are inexpensive and efficient is bound to gain importance. This paper reports the results of a study of the production of lactic acid from wastepaper as a representative cellulosic feedstock, using a batch, bench-scale simultaneous saccharification and fermentation (SSF) process. The effect on process performance of operating parameters such as pH, temperature, enzyme loading, solids concentration, and enzyme preparation has been examined. A lactic acid product yield of 84% of theoretical was achieved at a solids loading of 5%, using 25 filter paper units (FPU) of cellulase per gram of cellulose, at 45°C and pH 5.0. The pH and temperature of operation have been selected to achieve good performance of both the cellulase and the microoganism in the SSF process. Our studies show that a feedstock such as wastepaper offers considerable promise and opportunity in the future for development of a biomass-based process for lactic acid production. Received 09 January 1996/ Accepted in revised form 22 August 1996     

<Emphasis Type="SmallCaps">l</Emphasis>(+)-Lactic acid production from non-food carbohydrates by thermotolerant <Emphasis Type="Italic">Bacillus coagulans</Emphasis>

Lactic acid is used as an additive in foods, pharmaceuticals, and cosmetics, and is also an industrial chemical. Optically pure lactic acid is increasingly used as a renewable bio-based product to replace petroleum-based plastics. However, current production of lactic acid depends on carbohydrate feedstocks that have alternate uses as foods. The use of non-food feedstocks by current commercial biocatalysts is limited by inefficient pathways for pentose utilization. B. coagulans strain 36D1 is a thermotolerant bacterium that can grow and efficiently ferment pentoses using the pentose-phosphate pathway and all other sugar constituents of lignocellulosic biomass at 50°C and pH 5.0, conditions that also favor simultaneous enzymatic saccharification and fermentation (SSF) of cellulose. Using this bacterial biocatalyst, high levels (150–180 g l⁻¹) of lactic acid were produced from xylose and glucose with minimal by-products in mineral salts medium. In a fed-batch SSF of crystalline cellulose with fungal enzymes and B. coagulans, lactic acid titer was 80 g l⁻¹ and the yield was close to 80%. These results demonstrate that B. coagulans can effectively ferment non-food carbohydrates from lignocellulose to l(+)-lactic acid at sufficient concentrations for commercial application. The high temperature fermentation of pentoses and hexoses to lactic acid by B. coagulans has these additional advantages: reduction in cellulase loading in SSF of cellulose with a decrease in enzyme cost in the process and a reduction in contamination of large-scale fermentations.     

Microbial production of d‐lactic acid from dried distiller's grains with solubles

d ‐Lactic acid production is gaining increasing attention due to the thermostable properties of its polymer, poly‐d ‐lactic acid . In this study, Lactobacillus coryniformis subsp. torquens, was evaluated for its ability to produce d ‐lactic acid using Dried Distiller's Grains with Solubles (DDGS) hydrolysate as the substrate. DDGS was first subjected to alkaline pretreatment with sodium hydroxide to remove the hemicellulose component and the generated carbohydrate‐rich solids were then subjected to enzymatic hydrolysis using cellulase mixture Accellerase® 1500. When comparing separate hydrolysis and fermentation and simultaneous saccharification and fermentation (SSF) of L. coryniformis on DDGS hydrolysate, the latter method demonstrated higher d ‐lactic acid production (27.9 g/L, 99.9% optical purity of d ‐lactic acid), with a higher glucose to d ‐lactic acid conversion yield (84.5%) compared to the former one (24.1 g/L, 99.9% optical purity of d ‐lactic acid). In addition, the effect of increasing the DDGS concentration in the fermentation system was investigated via a fed‐batch SSF approach, where it was shown that the d ‐lactic acid production increased to 38.1 g/L and the conversion yield decreased to 70%. In conclusion, the SSF approach proved to be an efficient strategy for the production of d ‐lactic acid from DDGS as it reduced the overall processing time and yielded high d ‐lactic acid concentrations.     

Simultaneous saccharification and fermentation of cellulose to lactic acid

Recent interest in the industrial manufacture of ethanol and other organic chemicals from biomass has led to the utilization of surplus grain and cane juice as a fermentation feedstock. Since those starting materials are also foods, they are expensive. As an alternative, cellulosic substances-the most abundant renewable resources on earth(1)-have long been considered for conversion to readily utilizable hydrolyzates.(2, 3)For the production of ethanol from cellulose, we have proposed the simultaneous saccharification and fermentation (SSF) process.(4) In SSF, enzymatic cellulose hydrolysis and glucose fermentation to ethanol by yeast proceed simultaneously within one vessel. The process advantages-reduced reactor volume and faster saccharification rates-have been confirmed by many researchers.(5-8) During SSF, the faster saccharification rates result because the glucose product is immediately removed, considerably diminishing its inhibitory effect on the cellulase system.(9)To effectively apply the SSF method to produce substances fermented from glucose, several conditions should be satisfied. One is coincident enzymatic hydrolysis and fermentation conditions, such as pH and temperature. The other is that cellulase inhibition by the final product is less than that by glucose and/or cellobiose. One of us has reported that acetic acid, citric acid, itaconic acid, alpha-ketoglutaric acid, lactic acid, and succinic acid scarcely inhibit cellulase.(10) This suggests that if the microorganisms which produce these organic acids were compatible with cellulase reaction conditions, the organic acids could be produced efficiently from cellulosic substrates by SSF.In this article, the successful application of SSF to lactic acid production from cellulose is reported. Though there have been several reports of direct cellulose conversion to organic acids by anaerobes such as Clostridium, only trace amounts of lactic acid were detected in the fermentation medium among the low-molecular-weight fatty acid components.(11-13) Lactic acid is one of the most important organic acids and has a wide range of food-related and industrial applications.     

Batch and repeated batch production of l(+)-lactic acid by Enterococcus faecalis RKY1 using wood hydrolyzate and corn steep liquor

Lactic acid production was investigated for batch and repeated batch cultures of Enterococcus faecalis RKY1, using wood hydrolyzate and corn steep liquor. When wood hydrolyzate (equivalent to 50 g l⁻¹ glucose) supplemented with 15–60 g l⁻¹ corn steep liquor was used as a raw material for fermentation, up to 48.6 g l⁻¹ of lactic acid was produced with, volumetric productivities ranging between 0.8 and 1.4 g l⁻¹ h⁻¹. When a medium containing wood hydrolyzate and 15 g l⁻¹ corn steep liquor was supplemented with 1.5 g l⁻¹ yeast extract, we observed 1.9-fold and 1.6-fold increases in lactic acid productivity and cell growth, respectively. In this case, the nitrogen source cost for producing 1 kg lactic acid can be reduced to 23% of that for fermentation from wood hydrolyzate using 15 g l⁻¹ yeast extract as a single nitrogen source. In addition, lactic acid productivity could be maximized by conducting a cell-recycle repeated batch culture of E. faecalis RKY1. The maximum productivity for this process was determined to be 4.0 g l⁻¹ h⁻¹.     

Simultaneous saccharification and co-fermentation of crystalline cellulose and sugar cane bagasse hemicellulose hydrolysate to lactate by a thermotolerant acidophilic Bacillus sp

Polylactides produced from renewable feedstocks, such as corn starch, are being developed as alternatives to plastics derived from petroleum. In addition to corn, other less expensive biomass resources can be readily converted to component sugars (glucose, xylose, etc.) by enzyme and/or chemical treatment for fermentation to optically pure lactic acid to reduce the cost of lactic acid. Lactic acid bacteria used by the industry lack the ability to ferment pentoses (hemicellulose-derived xylose and arabinose), and their growth and fermentation optima also differ from the optimal conditions for the activity of fungal cellulases required for depolymerization of cellulose. To reduce the overall cost of simultaneous saccharification and fermentation (SSF) of cellulose, we have isolated bacterial biocatalysts that can grow and ferment all sugars in the biomass at conditions that are also optimal for fungal cellulases. SSF of Solka Floc cellulose by one such isolate, Bacillus sp. strain 36D1, yielded l(+)-lactic acid at an optical purity higher than 95% with cellulase (Spezyme CE; Genencor International) added at about 10 FPU/g cellulose, with a product yield of about 90% of the expected maximum. Volumetric productivity of SSF to lactic acid was optimal between culture pH values of 4.5 and 5.5 at 50 degrees C. At a constant pH of 5.0, volumetric productivity of lactic acid was maximal at 55 degrees C. Strain 36D1 also co-fermented cellulose-derived glucose and sugar cane bagasse hemicellulose-derived xylose simultaneously (SSCF). In a batch SSCF of 40% acid-treated hemicellulose hydrolysate (over-limed) and 20 g/L Solka Floc cellulose, strain 36D1 produced about 35 g/L lactic acid in about 144 h with 15 FPU of Spezyme CE/g cellulose. The maximum volumetric productivity of lactic acid in this SSCF was 6.7 mmol/L (h). Cellulose-derived lactic acid contributed to about 30% of this total lactic acid. These results show that Bacillus sp. strain 36D1 is well-suited for simultaneous saccharification and co-fermentation of all of the biomass-derived sugars to lactic acid.     

A short review on SSF – an interesting process option for ethanol production from lignocellulosic feedstocks

Simultaneous saccharification and fermentation (SSF) is one process option for production of ethanol from lignocellulose. The principal benefits of performing the enzymatic hydrolysis together with the fermentation, instead of in a separate step after the hydrolysis, are the reduced end-product inhibition of the enzymatic hydrolysis, and the reduced investment costs. The principal drawbacks, on the other hand, are the need to find favorable conditions (e.g. temperature and pH) for both the enzymatic hydrolysis and the fermentation and the difficulty to recycle the fermenting organism and the enzymes. To satisfy the first requirement, the temperature is normally kept below 37°C, whereas the difficulty to recycle the yeast makes it beneficial to operate with a low yeast concentration and at a high solid loading. In this review, we make a brief overview of recent experimental work and development of SSF using lignocellulosic feedstocks. Significant progress has been made with respect to increasing the substrate loading, decreasing the yeast concentration and co-fermentation of both hexoses and pentoses during SSF. Presently, an SSF process for e.g. wheat straw hydrolyzate can be expected to give final ethanol concentrations close to 40 g L^-1 with a yield based on total hexoses and pentoses higher than 70%.     

Effect of substrate and cellulase concentration on simultaneous saccharification and fermentation of steam-pretreated softwood for ethanol production

Economic optimization of the production of ethanol by simultaneous saccharification and fermentation (SSF) requires knowledge about the influence of substrate and enzyme concentration on yield and productivity. Although SSF has been investigated extensively, the optimal conditions for SSF of softwoods have yet not been determined. In this study, SO2-impregnated and steam-pretreated spruce was used as substrate for the production of ethanol by SSF. Commercial enzymes were used in combination with the yeast Saccharomyces cerevisiae. The effects of the concentration of substrate (2% to 10% w/w) and of cellulases (5 to 32 FPU/g cellulose) were investigated. SSF was found to be sensitive to contamination because lactic acid was produced. The ethanol yield increased with increasing cellulase loading. The highest ethanol yield, 68% of the theoretical based on the glucose and mannose present in the original wood, was obtained at 5% substrate concentration. This yield corresponds to 82% of the theoretical based on the cellulose and soluble glucose and mannose present at the start of SSF. A higher substrate concentration caused inefficient fermentation, whereas a lower substrate concentration, 2%, resulted in increased formation of lactic acid, which lowered the yield. Compared with separate hydrolysis and fermentation, SSF gave a higher yield and doubled the productivity.     

Lactobacillus pentosus CECT 4023 T co-utilizes glucose and xylose to produce lactic acid from wheat straw hydrolysate: Anaerobiosis as a key factor

Lactic acid is a versatile chemical that can be produced via fermentation of lignocellulosic materials. The heterolactic strain Lactobacillus pentosus CECT 4023 T, that can consume glucose and xylose, was studied to produce lactic acid from steam exploded wheat straw prehydrolysate. The effect of temperature and pH on bacterial growth was analyzed. Besides, the effect of oxygen on lactic acid production was tested and fermentation yields were compared in different scenarios. This strain showed very high tolerance to the inhibitors contained in the wheat straw prehydrolysate. The highest lactic acid yields based on present sugar, around 0.80 g g⁻¹, were obtained from glucose in presence of 25%, 50%, and 75% v v⁻¹ of prehydrolysate in strict anaerobiosis. Lactic fermentation of wheat straw hydrolysate obtained after enzymatic hydrolysis of the prehydrolysate yielded 0.39 g of lactic acid per gram of released sugars, which demonstrated the high potential of L. pentosus to produce lactic acid from hemicellulosic hydrolysates. Results presented herein not only corroborated the ability of L. pentosus to grow using mixtures of sugars, but also demonstrated the suitability of this strain to be applied as an efficient lactic acid producer in a lignocellulosic biorefinery approach. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 35: e2739, 2019     

Optimization of lactic acid production in SSF by Lactobacillus amylovorus NRRL B-4542 using Taguchi methodology

Lactic acid production parameter optimization using Lactobacillus amylovorus NRRL B-4542 was performed using the design of experiments (DOE) available in the form of an orthogonal array and a software for automatic design and analysis of the experiments, both based on Taguchi protocol. Optimal levels of physical parameters and key media components namely temperature, pH, inoculum size, moisture, yeast extract, MgSO4 . 7H20, Tween 80, and corn steep liquor (CSL) were determined. Among the physical parameters, temperature contributed higher influence, and among media components, yeast extract, MgSO4 . 7H20, and Tween 80 played important roles in the conversion of starch to lactic acid. The expected yield of lactic acid under these optimal conditions was 95.80% and the actual yield at optimum conditions was 93.50%.     

Effects of intermittent addition of cellulase for production of L-lactic acid from wastewater sludge by simultaneous saccharification and fermentation

An attempt was made to create L-lactic acid, a precursor of poly-lactic acid, which is a biodegradable plastic, from wastewater sludge from the paper-manufacturing industry. The sludge contained a high percentage of cellulose and needed to be hydrolyzed to glucose by the action of the cellulase before being treating with lactic acid bacteria. Therefore, a method involving simultaneous saccharification and fermentation (SSF) was carried out. The optimum pH of the SSF for production of the lactic acid by the newly isolated lactic acid bacterium with a high selectively of L-lactic acid was found out to be around pH = 5.0, and the optimum temperature to be approximately 40 degrees C. On the basis of the measurement of the cell density changes in the lactic acid bacteria, it was ascertained that the bacterial activity could continue at a high level for a relatively long period of time, and that the L-lactic acid productivity was diminished by the rapid deactivation of the cellulase. With the intermittent addition of cellulase once daily for the sake of compensating for the cellulase deactivation, the L-lactic acid attained a maximum concentration of 16.9 g/L, i.e., a 72.2% yield based on the potential glucose contained in the sludge under optimum pH and temperature conditions.     

A short review on SSF - an interesting process option for ethanol production from lignocellulosic feedstocks

Simultaneous saccharification and fermentation (SSF) is one process option for production of ethanol from lignocellulose. The principal benefits of performing the enzymatic hydrolysis together with the fermentation, instead of in a separate step after the hydrolysis, are the reduced end-product inhibition of the enzymatic hydrolysis, and the reduced investment costs. The principal drawbacks, on the other hand, are the need to find favorable conditions (e.g. temperature and pH) for both the enzymatic hydrolysis and the fermentation and the difficulty to recycle the fermenting organism and the enzymes. To satisfy the first requirement, the temperature is normally kept below 37 degrees C, whereas the difficulty to recycle the yeast makes it beneficial to operate with a low yeast concentration and at a high solid loading. In this review, we make a brief overview of recent experimental work and development of SSF using lignocellulosic feedstocks. Significant progress has been made with respect to increasing the substrate loading, decreasing the yeast concentration and co-fermentation of both hexoses and pentoses during SSF. Presently, an SSF process for e.g. wheat straw hydrolyzate can be expected to give final ethanol concentrations close to 40 g L-1 with a yield based on total hexoses and pentoses higher than 70%.     

Effect of pH control on lactic acid fermentation of starch by Lactobacillus manihotivorans LMG 18010T

Lactic acid fermentation of starch by Lactobacillus manihotivorans LMG 18010T, a new amylolytic L(+) lactic acid producer, was investigated and compared with starch fermentation by Lact. plantarum A6. At non-controlled pH, growth and lactic acid production from starch by Lact. manihotivorans LMG 18010T lasted 25 h. Specific growth and lactic acid production rates continuously decreased from the onset of the fermentation, unlike Lact. plantarum A6 which was able to grow and convert starch product hydrolysis into lactic acid more rapidly and efficiently at a constant rate up to pH 4.5. In spite of complete and rapid starch hydrolysis by Lact. manihotivorans LMG 18010T during the first 6 h, only 45% of starch hydrolysis products were converted to lactic acid. When pH was maintained at 6.0, lactic acid, amylase and final biomass production by Lact. manihotivorans LMG 18010T increased markedly and the fermentation time was reduced by half. Under the same conditions, an increase only in amylase production was observed with Lact. plantarum A6. When grown on glucose or starch at pH 6.0, Lact. manihotivorans LMG 18010T had an identical maximum specific growth rate (0.35 h(-1)), whereas the maximum rate of specific lactic acid production was three times higher with glucose as substrate. Lactobacillus manihotivorans LMG 18010T did not produce amylase when grown on glucose. Based on the differences in the physiology between the two species and other amylolytic lactic acid bacteria, different applications may be expected.     

Product inhibition in simultaneous saccharification and fermentation of cellulose into lactic acid

The product, lactic acid, strongly inhibited microbial activity in lactic acid fermentation. The volumetric productivity declined from 1.19 g/l.h with zero lactic acid (control) to only 0.18 g/l.h when lactic acid reached 65 g/l. Lactic acid also inhibited cellulase activity but less severely than the inhibition on microbial activity as lactic acid above 90 g/l was needed for 50% inhibition. A gradual deterioration of the Simultaneous Saccharification and Fermentation (SSF) process occurred with the build-up of lactic acid and the rate-controlling step in SSF shifted from hydrolysis to fermentation as the bioprocess proceeded.     

Enzymatic hydrolysis and simultaneous saccharification and fermentation of alkali/peracetic acid-pretreated sugarcane bagasse for ethanol and 2,3-butanediol production

The enzymatic digestibility of alkali/peracetic acid (PAA)-pretreated bagasse was systematically investigated. The effects of initial solid consistency, cellulase loading and addition of supplemental β-glucosidase on the enzymatic conversion of glycan were studied. It was found the alkali-PAA pulp showed excellent enzymatic digestibility. The enzymatic glycan conversion could reach about 80% after 24 h incubation when enzyme loading was 10 FPU/g solid. Simultaneous saccharification and fermentation (SSF) results indicated that the pulp could be well converted to ethanol. Compared with dilute acid pretreated bagasse (DAPB), alkali-PAA pulp could obtain much higher ethanol and xylose concentrations. The fermentation broth still showed some cellulase activity so that the fed pulp could be further converted to sugars and ethanol. After the second batch SSF, the fermentation broth of alkali-PAA pulp still kept about 50% of initial cellulase activity. However, only 21% of initial cellulase activity was kept in the fermentation broth of DAPB. The xylose syrup obtained in SSF of alkali-PAA pulp could be well converted to 2,3-butanediol by Klebsiella pneumoniae CGMCC 1.9131.     

Optimization of lactic acid production from beet molasses by Lactobacillus delbrueckii NCIMB 8130

Production of lactic acid from beet molasses by Lactobacillus delbrueckii NCIMB 8130 in static and shake flask fermentation was investigated. Shake flasks proved to be a better fermentation system for this purpose. Substitution of yeast extract with other low cost protein sources did not improve lactic acid production. The maximum lactic acid concentration was achieved without treatment of molasses. A Central Composite Design was employed to determine the maximum lactic acid concentration at optimum values for the process variables (sucrose, yeast extract, CaCO₃). A satisfactory fit of the model was realized. Lactic acid production was significantly affected both by sucrose–yeast extract and sucrose–CaCO₃ interactions, as well as by the negative quadratic effects of these variables. Sucrose and yeast extract had a linear effect on lactic acid production while the CaCO₃ had no significant linear effect. The maximum lactic acid concentration (88.0 g/l) was obtained at concentrations for sucrose, yeast extract and CaCO₃ of 89.93, 45.71 and 59.95 g/l, respectively.     

A media design program for lactic acid production coupled with extraction by electrodialysis

The aim of this study was to investigate industrial media for lactic acid fermentation to reduce the cost of nitrogen sources. Corn steep liquor (CSL) was successfully used at 5% (v/v) in batch fermentations. Use of soluble CSL improved the productivity approximately 20% with an advantage of clearer fermentation broth. Yeast extract (YE)-complemented CSL media further increased the productivity. It was found that 3.1 g L(-1) yeast extract and 5% CSL could be an effective substitute for 15 g L(-1) yeast extract in 10% glucose medium. Spent brewery yeast was also used as a sole nitrogen source equivalent to 5% CSL. Lactic acid was recovered by electrodialysis from the cell free broth. Depleted cell free broth supplemented with 5 g L(-1) of yeast extract performed reasonably in batch cultures. Reuse of the fermentation broth may reduce the cost of raw materials as well as minimize the fermentation wastes.     

Solid-state fermentation of cornmeal with the ascomycete <Emphasis Type="Italic">Morchella esculenta</Emphasis> for degrading starch and upgrading nutritional value

The ability of the ascomycete Morchella esculenta to degrade starch and upgrade nutritional value of cornmeal during solid-state fermentation (SSF) was studied. On the basal medium, α-amylase activity of M. esculenta reached its maximum value of 215 U g⁻¹ of culture on day 20 after inoculation. Supplementation of glucose, yeast extract to the basal medium caused a significant increase in either the degradation rate of starch or the mycelial biomass as compared with control (P < 0.01). Through orthogonal experiments, the theoretical optimum culture medium for SSF of this fungus was the following: 100 g cornmeal, ground to 30-mesh powder, moistened with 67 ml of nutrient salt solution supplemented with 3 g yeast extract and 10 g glucose per liter. Under the optimum culture condition, the degradation rate of starch reached its maximum values of 74.8%; the starch content of the fermented product decreased from 64.5 to 23.5%.