Biopolymer flocculant produced by an Pseudomonas sp.

A biopolymer flocculant produced by Pseudomonas sp. A-99 had flocculating activity both in inorganic suspensions containing Ca2, Mg2 or Fe3 and in organic suspensions containing Fe2, Fe3 or Al3. The flocculant was an acidic protein and contained a small amount of an acidic polysaccharide consisting of galacturonic acid, glucose and galactose. Productivity of the flocculant was about 450 mg/l medium. © Rapid Science Ltd. 1998     

Production of a biopolymer flocculant from Bacillus licheniformis and its flocculation properties

Bacillus licheniformis CCRC 12826 produced extracellularly an excellent biopolymer flocculant in a large amount when it was grown aerobically in a culture medium containing citric acid, glutamic acid and glycerol as carbon sources. The biopolymer flocculant was an extremely viscous material with a molecular weight over 2 x 10(6) by gel permeation chromatography. It could be easily purified from the culture medium by ethanol precipitation. It was shown to be a homopolymer of glutamic acid by amino acid analysis and thin layer chromatography and presumed to be poly-glutamic acid (PGA). This bioflocculant efficiently flocculated various organic and inorganic suspensions. It flocculated a suspended kaolin suspension without cations, although its flocculating activity was synergistically stimulated by the addition of bivalent or trivalent cations Ca2+, Fe3+ and Al3+. However, the synergistic effects of metal cations were most effective at neutral pH ranges. The comparison of the flocculating activity between the present biopolymer and a commercial lower molecular weight product showed that the biopolymer of the present study had much higher activity. The high productivity and versatile applications of PGA make its development as a new biodegradable, harmless, biopolymer flocculant economical and advantageous.     

Flocculation properties of xanthan produced by Xanthomonas campestris

Summary Xanthan had a flocculating activity in a kaolin suspension and high flocculating activity was obtained in the suspension (pH 7.0) adding Al³⁺, Fe³⁺ or Fe²⁺. Xanthan had high flocculating activity not only in other inorganic suspensions such as active carbon and acid clay but also in organic suspensions of cellulose and yeast. From these flocculation properties, xanthan is anticipated to be utilized in wide areas as a new biodegradable, harmless biopolymer flocculant.     

高效絮凝剂产生菌的筛选及絮凝活性研究

从污泥中分离筛选出1株具有高絮凝活性的细菌菌株F78,对其进行了分子鉴定,测得该菌16SrDNA长度为1501 bp,在GenBank中的登录号为EU443097,序列比对结果显示,该菌与粪产碱杆菌(Alcaligenes faecalis)的16S rDNA碱基序列相似性为99%。絮凝活性物质可由F78菌株分泌到胞外,通过对絮凝活性影响因素的研究,发现Ca2 的助凝效果比Fe3 、Fe2 、K 、Na 好;在高岭土悬液pH 3.0~12.0范围内,能保持较高的絮凝活性;菌株F78产生的絮凝活性物质具有良好的热稳定性。     

Flocculation properties of pectin in various suspensions

Pectin had a flocculating activity and its flocculating activities in various suspensions were investigated. Flocculating activity of pectin in a kaolin suspension was markedly stimulated by the addition of Al3+ and Fe3+ to the suspension. Optimum temperature for flocculating activity of pectin in the kaolin suspension was around 30 degrees C and high flocculating activity was obtained when 30 mg/l of pectin and 0.2 mM Fe3+ were added to the suspension. Other inorganic suspensions of activated carbon and acid clay were flocculated by pectin in the presence of Al3+ or Fe3+. Flocculation of organic suspensions such as cellulose and yeast by pectin occurred when 0.1-0.2 mM Fe3+ was present in the suspensions.     

一株絮凝剂产生菌的筛选及其絮凝特性研究

目的:筛选并研究对有毒物质有一定耐受性的絮凝剂产生菌。方法:利用含苯酚、邻苯二甲酸二丁酯和Pb2(SO4)3的分离培养基从土壤和活性污泥中分离筛选絮凝剂产生菌,对所得的菌种进行摇瓶发酵试验,分别考察其产絮凝剂的周期、絮凝活性分布以及对有毒物质的耐受性等特征,通过提取絮凝剂,将其絮凝活性与其它絮凝剂进行比较。结果:得到一株对苯酚具有一定耐受性的絮凝剂产生菌B2(Serratiasp.),其产絮凝剂的最佳培养时间为48h,絮凝率高于80%。苯酚浓度达0.6g/L时,B2菌的絮凝活性仍高于70%。其90%的絮凝物质集中于菌体,且热稳定性好,对多种悬浊液的絮凝活性高于硫酸铝、PAC。结论:新型絮凝剂产生菌B2对苯酚耐受性强,且絮凝剂提取简便,具有重要的研究价值。     

Characteristics of a biopolymer flocculant produced by Bacillus sp. PY-90

A biopolymer flocculant-producing bacterium, strain PY-90, was isolated and considered to belong to Bacillus subtilis. For the production of biopolymer flocculant by strain PY-90, a medium containing 2 to 5% l-glutamic acid as a nitrogen source was suitable. The biopolymer flocculant was a homopolymer composed of glutamic acid residues and was presumed to be poly(γ-glutamic acid). In kaolin suspension, the highest flocculating activity was attained at the biopolymer flocculant concentration of 20 mg/l. The flocculating activity was increased by the addition of Ca²⁺, and the optimum concentration of which was about 2 to 8 mM. The flocculating activity was high in an acidic pH range of 3.0 to 5.0, and decreased upon heating at 100°C.     

Abiogenic Photophosphorylation of ADP to ATP Sensitized by Flavoproteinoid Microspheres

A model for abiogenic photophosphorylation of ADP by orthophosphate to yield ATP was studied. The model is based on the photochemical activity of flavoproteinoid microspheres that are formed by aggregation in an aqueous medium of products of thermal condensation of a glutamic acid, glycine and lysine mixture (8:3:1) and contain, along with amino acid polymers (proteinoids), abiogenic isoalloxazine (flavin) pigments. Irradiation of aqueous suspensions of microspheres with blue visible light or ultraviolet in the presence of ADP and orthophosphate resulted in ATP formation. The yield of ATP in aerated suspensions was 10-20% per one mol of starting ADP. Deaeration reduced the photophosphorylating activity of microspheres five to 10 times. Treatment of aerated microsphere suspensions with superoxide dismutase during irradiation partially suppressed ATP formation. Deaerated microspheres restored completely their photophosphorylating activity after addition of hydrogen peroxide to the suspension. The photophosphorylating activity of deaerated suspensions of flavoproteinoid microspheres was also recovered by introduction of Fe3+-cytochrome c, an electron acceptor alternative to oxygen. On the basis of the results obtained, a chemical mechanism of phosphorylation is proposed in which the free radical form of reduced flavin sensitizer (F1H*) and ADP are involved.     

Flocculation of microalgae in brackish and sea waters

Flocculation is an essential step in the concentration and harvesting of microalgae from aquatic media. Salinity of brackish water and sea water requires high flocculant dosages and renders flocculation less effective than in freshwater algal media. Experiments with the marine microalgae Isochrysis galbana and Chlorella stigmatophora showed that effective alum or ferric chloride flocculation was obtained only with dosages which are 5 to 10 times higher than the dosages required for the flocculation of freshwater microalgae. The flocculant dosages required for removing over 90% of the algae from suspensions were found to increase linearly with salinity as expressed in ionic strength. High salinity was found to inhibit flocculation with polyelectrolytes which are quite effective in freshwater algae flocculation. This inhibition was diminished at reduced salinity levels and effective flocculation was attained at salinity levels of 5 g/liter and below, which is typical of desert brackish water. Two methods were found to induce flocculation in sea water: (a) combining polyelectrolytes with inorganic flocculants such as ferric chloride or alum, and (b) ozone oxidation pretreatment followed by flocculation with inorganic flocculants.     

Characterization of a bioflocculant produced by the marine myxobacterium Nannocystis sp. NU-2

The marine myxobacterium strain NU-2, which can grow on high concentrations (up to 7%) of NaCl, was isolated from a salt soil sample collected from the coast of the Huanghai Sea, China. Morphological properties and 16S rDNA sequence analysis indicated that the isolate is a novel species related to the genus Nannocystis. Nannocystis sp. NU-2 produced a new kind of flocculating substance in a starch medium with a yield of 14.8 g l^–1. The NU-2 flocculant was composed of 40.3% proteins and 56.5% polysaccharides, of which glucose, mannose and glucuronic acid were the principal constituents in the relative proportions of 5:4:1. The flocculation activity of the NU-2 flocculant depends strongly on cations such as Fe³⁺ and Al³⁺. When a 30 mg l^–1 FeCl₃ solution is present in kaolin clay suspension, 30 mg l^–1of the flocculant produced a high flocculating activity value of 90%, which remained unchanged over an extensive pH range (pH 2.0–13.0). The flocculant was tested for its ability to bleach dyeing liquors, and the bleaching activities were 98.2% for acid red in 100 mg l^–1of the flocculant and 99.0% for direct emerald blue in 50 mg l^–1of the flocculant under test conditions. Use of the flocculant to bleach basic pink and cation emerald blue liquors was not effective. Electronic Publication     

Bacterial degradation of EDTA

Degradation of EDTA (ethylenediaminetetraacetic acid) or metal-EDTA complexes by cell suspensions of the bacterial strain DSM 9103 was studied. The activity of EDTA degradation was the highest in the phase of active cell growth and decreased considerably in the stationary phase, after substrate depletion in the medium. Exponential-phase cells were incubated in HEPES buffer (pH 7.0) with 1 mM of uncomplexed EDTA or EDTA complexes with Mg2+, Ca2+, Mn2+, Pb2+, Co2+, Cd2+, Zn2+, Cu2+, or Fe3+. The metal-EDTA complexes (Me-EDTA) studied could be divided into three groups according to their degradability. EDTA complexes with stability constants K below 10(16) (lg K < 16), such as Mg-EDTA, Ca-EDTA, and Mn-EDTA, as well as uncomplexed EDTA, were degraded by the cell suspensions at a constant rate to completion within 5-10 h of incubation. Me-EDTA complexes with lg K above 16 (Zn-EDTA, Co-EDTA, Pb-EDTA, and Cu-EDTA) were not completely degraded during a 24-hour incubation, which was possibly due to the toxic effect of the metal ions released. No degradation of Cd-EDTA or Fe(III)-EDTA by cell suspensions of strain DSM 9103 was observed under the conditions studied.     

Murine leukemia virus clearance by flocculation and microfiltration

Clearance of murine leukemia virus from CHO cell suspensions by flocculation and microfiltration was investigated. Murine leukemia virus is a retrovirus that is recommended by the U.S. Food and Drug Administration for validating clearance of retrovirus-like particles. Due to biosafety considerations, an amphotropic murine leukemia virus vector (A-MLV) that is incapable of self-replication was used. Further, A-MLV is incapable of infecting CHO cells, thus ensuring that infection of the CHO cells in the feed did not result in a reduced virus titer in the permeate. The virus vector contains the gene for the enhanced green fluorescent protein (EGFP) to facilitate assaying for infectious virus particles. The virus particles are 80-130 nm in size. The feed streams were flocculated using a cationic polyelectrolyte. Microfiltration was conducted using 0.1 and 0.65 microm pore size hollow fiber membranes. The level of virus clearance in the permeate was determined. For the 0.1 microm pore size membranes a 1,000-fold reduction in the virus titer in the permeate was observed for feed streams consisting of A-MLV, A-MLV plus flocculant, A-MLV plus CHO cells, and A-MLV plus flocculant and CHO cells. While the flocculant had little effect on the level of virus clearance in the permeate for 0.1 microm pore size membranes, it did lead to higher permeate fluxes for the CHO cell feed streams. Virus clearance experiments conducted with 0.65 microm pore size membranes indicate little clearance of A-MLV from the permeate in the absence of flocculant. However, in the presence of flocculant the level of virus clearance in the permeate was similar to that observed for 0.1 microm pore size membranes. The results obtained here indicate that significant clearance of A-MLV is possible during tangential flow microfiltration. Addition of a flocculant is essential if the membrane pore size is greater than the diameter of the virus particles. Flocculation of the feed stream leads to an increase in the permeate flux.     

一株产微生物絮凝剂菌株的分离鉴定及特性

从活性污泥中分离筛选到一株产絮凝剂的细菌A25,鉴定为巨大芽孢杆菌Bacillus megaterium。该菌株产絮凝剂的最适碳源为麦芽糖,最适氮源为酵母提取物,最适pH为7.－10.0。絮凝剂的形成与菌体生长同步,均在10h达到最高值,该絮凝剂主要分布在发酵液中,另外还有一部分存在于菌体上,所产絮凝剂对供试的各种悬浮液和菌悬液都具有良好的絮凝效果。     

淀粉-接枝-聚丙烯酰胺共聚物的絮凝性能

用Ce~(4+)盐作引发剂合成了淀粉-接枝-聚丙烯酰胺(S-g-PAM) 共聚物,比较了S-g-PAM和聚丙烯酰胺(PAM)对钠型膨润土悬浮液的絮凝作用。作为絮凝剂,S-g-PAM的某些性能优于PAM。S-g-PAM对悬浮在醋酸溶液中的偏苯三酸晶体有较好的絮凝性能。     

Purification and Chemical Analysis of Microbial Cell Flocculant Produced by Aspergillus sojae AJ7002

A bio-flocculant was isolated from the culture broth of Asp. sojae AJ 7002. It was partially purified by acetone or ethanol precipitation, by ion-exchange and gel chromatography, and by dialysis. The isolated polymer possessed chemical characteristics of a poly-hexosamine and a protein. Glucosamine and galactosamine were not acetylated. The flocculant contained 2-ketogluconic acid, but sulfur or phosphorus was not detected. This flocculant was thermo-stable and its activity varied with pH. It was suggested that the hexosamine moiety in the polymer played a major role in bio-flocculation, assisted by protein portion in enlargement of the molecular weight of the flocculant, and by 2-ketogluconic acid in endowing it with amphoteric character.     

A novel flocculant biopolymer produced by Pestalotiopsis sp. KCTC 8637P

Summary A white rot fungus was isolated from rotted leaves and identified as Pestalotiopsis sp. KCTC 8637P. It produced a flocculant biopolymer. A flocculant was partially purified from the culture broth by series of precipitations with 95% ethanol and named as Pestan. The components of Pestan were consisted of glucose : glucosamine : glucuronic acid : rhamnose with a approximately molar ratio of 100:3.5:1.6:1.3.In kaolin suspension(final concentration was 4,800 mg/l), the highest flocculating activity was attained at the biopolymer flocculant concentration of 1 mg/l . The flocculating activity was observed most highest by the addition of cationic solutions, especially 8mM CaCl₂ · 2H₂O or 8mM FeCl₃. The thermal stability of Pestan was sustained up to 70 °C.     

Microbiological solubilization of metals from complex sulfide ore material in aerated column reactors

Finely ground ore material (90%–200 mesh) was subjected to acid microbiological leaching in 20% and 30% (wt/vol) suspensions. The rate of aeration was maintained at 2 and 4 1/min · 1. After the onset of the microbiological phase of leaching, the solubilization of iron was initially rapid but was succeeded by Fe(III) precipitation. Major differences were apparent between inoculated and uninoculated suspensions for each metal analyzed (Fe, Al, Co, Cu, Ni, Zn). The sulfur balance in leach residues indicated elevated levels of elemental S and sulfate in the inoculated systems.     

Characterization of an extracellular flocculating substance produced by a planktonic cyanobacterium, Anabaena sp.

Two planktonic cyanobacteria, Anabaena sp. N1444 and Anabaena sp. PC-1, and a green eukaryotic alga, Scene-desmus sp., produced extracellular flocculants. The flocculant of Anabaena PC-1, when purified, was found to be a macromolecular polysaccharide consisting of neutral sugars, uronic acids, and proteins, but not keto acids, hexosamines nor fatty acids. The flocculant bound a cationic dye, Alcian Blue, indicating it to be polyanionic. The flocculating activity was high under acidic conditions, slightly enhanced by the addition of salts and metals, and increased to about 40% upon heating at 100 °C for 7 min. The flocculant could flocculated various inorganic and organic compounds in solution. © Rapid Science Ltd. 1998