Improvement of engine emissions with conventional diesel fuel and diesel-biodiesel blends

In this report combustion and exhaust emissions with neat diesel fuel and diesel-biodiesel blends have been investigated. In the investigation, firstly biodiesel from non-edible neem oil has been made by esterification. Biodiesel fuel (BDF) is chemically known as mono-alkyl fatty acid ester. It is renewable in nature and is derived from plant oils including vegetable oils. BDF is non-toxic, biodegradable, recycled resource and essentially free from sulfur and carcinogenic benzene. In the second phase of this investigation, experiment has been conducted with neat diesel fuel and diesel-biodiesel blends in a four stroke naturally aspirated (NA) direct injection (DI) diesel engine. Compared with conventional diesel fuel, diesel-biodiesel blends showed lower carbon monoxide (CO), and smoke emissions but higher oxides of nitrogen (NOx) emission. However, compared with the diesel fuel, NOx emission with diesel-biodiesel blends was slightly reduced when EGR was applied.     

Influence of tall oil biodiesel with Mg and Mo based fuel additives on diesel engine performance and emission

The purpose of this study is to investigate influences of tall oil biodiesel with Mg and Mo based fuel additives on diesel engine performance and emission. Tall oil resinic acids were reacted with MgO and MoO(2) stoichiometrically for the production of metal-based fuel additives (combustion catalysts). The metal-based additives were added into tall oil biodiesel (B60) at the rate of 4 micromol/l, 8 micromol/l and 12 micromol/l for preparing test fuels. In general, both of the metal-based additives improved flash point, pour point and viscosity of the biodiesel fuel, depending on the rate of additives. A single cylinder DI diesel engine was used in the tests. Engine performance values did not change significantly with biodiesel fuels, but exhaust emission profile was improved. CO emissions and smoke opacity decreased by 56.42% and by 30.43%, respectively. In general, low NO(x) and CO(2) emissions were measured with the biodiesel fuels.     

Effects of mixing system and pilot fuel quality on diesel–biogas dual fuel engine performance

This paper describes results obtained from CI engine performance running on dual fuel mode at fixed engine speed and four loads, varying the mixing system and pilot fuel quality, associated with fuel composition and cetane number. The experiments were carried out on a power generation diesel engine at 1500 m above sea level, with simulated biogas (60% CH₄–40% CO₂) as primary fuel, and diesel and palm oil biodiesel as pilot fuels. Dual fuel engine performance using a naturally aspirated mixing system and diesel as pilot fuel was compared with engine performance attained with a supercharged mixing system and biodiesel as pilot fuel. For all loads evaluated, was possible to achieve full diesel substitution using biogas and biodiesel as power sources. Using the supercharged mixing system combined with biodiesel as pilot fuel, thermal efficiency and substitution of pilot fuel were increased, whereas methane and carbon monoxide emissions were reduced.     

Diesel particulate emissions from used cooking oil biodiesel

Two different biodiesel fuels, obtained from waste cooking oils with different previous uses, were tested in a DI diesel commercial engine either pure or in 30% and 70% v/v blends with a reference diesel fuel. Tests were performed under a set of engine operating conditions corresponding to typical road conditions. Although the engine efficiency was not significantly affected, an increase in fuel consumption with the biodiesel concentration was observed. This increase was proportional to the decrease in the heating value. The main objective of the work was to study the effect of biodiesel blends on particulate emissions, measured in terms of mass, optical effect (smoke opacity) and size distributions. A sharp decrease was observed in both smoke and particulate matter emissions as the biodiesel concentration was increased. The mean particle size was also reduced with the biodiesel concentration, but no significant increases were found in the range of the smallest particles. No important differences in emissions were found between the two tested biodiesel fuels.     

Combustion behaviors of a compression-ignition engine fueled with diesel/methanol blends under various fuel delivery advance angles

A stabilized diesel/methanol blend was described and the basic combustion behaviors based on the cylinder pressure analysis was conducted in a compression-ignition engine. The study showed that increasing methanol mass fraction of the diesel/methanol blends would increase the heat release rate in the premixed burning phase and shorten the combustion duration of the diffusive burning phase. The ignition delay increased with the advancing of the fuel delivery advance angle for both the diesel fuel and the diesel/methanol blends. For a specific fuel delivery advance angle, the ignition delay increased with the increase of the methanol mass fraction (oxygen mass fraction) in the fuel blends and the behaviors were more obvious at low engine load and/or high engine speed. The rapid burn duration and the total combustion duration increased with the advancing of the fuel delivery advance angle. The centre of the heat release curve was close to the top-dead-centre with the advancing of the fuel delivery advance angle. Maximum cylinder gas pressure increased with the advancing of the fuel delivery advance angle, and the maximum cylinder gas pressure of the diesel/methanol blends gave a higher value than that of the diesel fuel. The maximum mean gas temperature remained almost unchanged or had a slight increase with the advancing of the fuel delivery advance angle, and it only slightly increased for the diesel/methanol blends compared to that of the diesel fuel. The maximum rate of pressure rise and the maximum rate of heat release increased with the advancing of the fuel delivery advance angle of the diesel/methanol blends and the value was highest for the diesel/methanol blends.     

Ethanol-diesel fuel blends -- a review

Ethanol is an attractive alternative fuel because it is a renewable bio-based resource and it is oxygenated, thereby providing the potential to reduce particulate emissions in compression-ignition engines. In this review the properties and specifications of ethanol blended with diesel fuel are discussed. Special emphasis is placed on the factors critical to the potential commercial use of these blends. These factors include blend properties such as stability, viscosity and lubricity, safety and materials compatibility. The effect of the fuel on engine performance, durability and emissions is also considered. The formulation of additives to correct certain key properties and maintain blend stability is suggested as a critical factor in ensuring fuel compatibility with engines. However, maintaining vehicle safety with these blends may entail fuel tank modifications. Further work is required in specifying acceptable fuel characteristics, confirming the long-term effects on engine durability, and ensuring safety in handling and storing ethanol-diesel blends.     

Combustion characteristics of a turbocharged DI compression ignition engine fueled with petroleum diesel fuels and biodiesel

In this study, the combustion characteristics and emissions of two different petroleum diesel fuels (No. 1 and No. 2) and biodiesel from soybean oil were compared. The tests were performed at steady state conditions in a four-cylinder turbocharged DI diesel engine at full load at 1400-rpm engine speed. The experimental results compared with No. 2 diesel fuel showed that biodiesel provided significant reductions in PM, CO, and unburned HC, the NO(x) increased by 11.2%. Biodiesel had a 13.8% increase in brake-specific fuel consumption due to its lower heating value. However, using No. 1 diesel fuel gave better emission results, NO(x) and brake-specific fuel consumption reduced by 16.1% and 1.2%, respectively. The values of the principal combustion characteristics of the biodiesel were obtained between two petroleum diesel fuels. The results indicated that biodiesel may be blended with No. 1 diesel fuel to be used without any modification on the engine.     

The use of a fuel containing Chlorella vulgaris in a diesel engine

There is a need for sustainable fuels for diesel engines and fuels containing particles will function as a fuel in diesel engines. Some microalgae such as Chlorella vulgaris are unicellular and 5–10 μm in size, which is suitable for combining in an emulsion fuel. An emulsion consisting of transesterified rapeseed oil, a surfactant and a slurry of C. vulgaris was used as a fuel in an unmodified single cylinder diesel engine. The fuel consumption and emissions of this fuel was determined and although the carbon monoxide levels were higher the NO_x emission was lower than that of diesel.     

Current and Potential Biofuel Production from Plant Oils

Environmental concerns and depletion of fossil fuels along with government policies have led to the search for alternative fuels from various renewable and sustainable feedstocks. This review provides a critical overview of the chemical composition of common commercial plant oils, i.e., palm oil, olive oil, rapeseed oil, castor oil, WCO, and CTO and their recent trends toward potential biofuel production. Plant oils with a high energy content are primarily composed of triglycerides (generally >?95%), accompanied by diglycerides, monoglycerides, and free fatty acids. The heat content of plant oils is close to 90% for diesel fuels. The oxygen content is the most important difference in chemical composition between fossil oils and plant oils. Triglycerides can even be used directly in diesel engines. However, their high viscosity, low volatility, and poor cold flow properties can lead to engine problems. These problems require that plant oils need to be upgraded if they are to be used as a fuel in conventional diesel engines. Biodiesel, biooil, and renewable diesel are the three major biofuels obtained from plant oils. The main constraint associated with the production of biodiesel is the cost and sustainability of the feedstock. The renewable diesel obtained from crude tall oil is more sustainable than biofuels obtained from other feedstocks. The fuel properties of renewable diesel are similar to those of fossil fuels with reduced greenhouse gas emissions. In this review, the chemical composition of common commercial plant oils, i.e., palm oil, olive oil, rapeseed oil, castor oil, and tall oil, are presented. Both their major and minor components are discussed. Their compositions and fuel properties are compared to both fossil fuels and biofuels.     

Solubility of multi-component biodiesel fuel systems

Solubility of biodiesel fuel components in fossil diesel fuel-methanol-rapeseed oil methyl ester, fossil diesel fuel-ethanol-rapeseed oil methyl ester and fossil diesel fuel-ethanol-rapeseed oil ethyl ester systems was investigated. The solubility of components in the fossil diesel fuel-ethanol-rapeseed oil methyl ester system at 20 degrees C was substantially higher than in the fossil diesel fuel-methanol-rapeseed oil methyl ester system. The solubility of components in the fossil diesel fuel-ethanol-rapeseed oil ethyl ester system was slightly lower than in the fossil diesel fuel-ethanol-rapeseed oil methyl ester mixture. The moisture content of ethanol had a great influence on mixture solubility. With decrease of temperature, the solubility of components in the fossil diesel fuel-ethanol-rapeseed oil methyl ester system decreased.     

Potential Application of Turnip Oil (Raphanus sativus L.) for Biodiesel Production: Physical–Chemical Properties of Neat Oil, Biofuels and their Blends with Ultra-Low Sulphur Diesel (ULSD)

Turnip oil (TO; Raphanus sativus L.) produces seeds that contain around 26 wt% of inedible base stock that are suitable as a potential feedstock for biodiesel production. A turnip oil methyl ester (TME) was prepared from acid-catalyzed pretreated TO in an effort to evaluate important fuel properties of turnip oil-based biodiesel, such as kinematic viscosity, cloud point, pour point (PP), cold filter plugging point, acid value, oxidative stability and lubricity. A comparison was made with soybean oil methyl esters (SME) as per biodiesel fuel standards such as ASTM D6751 and EN 14214. TME was characterized using FTIR, HPLC and ¹H NMR. Except PP property, SME displays superior fuel properties compared to TME. Blends (B5 and B20) of TME in ultra-low sulphur diesel fuel (ULSD) were also assessed for the aforesaid fuel properties and compared to an analogous set of blends of soybean oil methyl ester in ULSD as per petro diesel fuel standards such as ASTM D975 and D7467. TME B5 blends in ULSD displayed improved PP property in comparison to neat ULSD and blends of SME in ULSD. It was demonstrated that the B5 and B20 blends of TME in ULSD had acceptable fuel properties as per ASTM D975 (for B5 blend) and ASTM D7467 (for B20 blend). In summary, turnip oil has potential as an alternative, non-food feedstock for biodiesel production.     

Biodiesel Production from Non-edible Oils of Jatropha and Karanj for Utilization in Electrical Generator

The biodiesel processor was developed for the production of biodiesel from non-edible oil of jatropha and karanj. The newly developed biodiesel processor is suitable for farmers in village level biodiesel production. The biodiesel processor was capable of producing 15 kg biodiesel per batch in 1.5 h at reaction temperature of 60°C. The biodiesel was produced from raw jatropha and karanj oil, and its blends with diesel were tested for power generation in a 7.5-kVA diesel engine generator set. The fuel properties, namely, kinematic viscosity and specific gravity, were found within the limits of Bureau of Indian Standards specifications. The overall efficiency of the generator for 4,500 W loading condition of jatropha- and karanj-biodiesel-blended fuel were recorded in the range of 21–23% and 24–27%, respectively. The overall efficiency of the generator for 6,000 W loading conditions was improved for jatropha and karanj biodiesel blends and were found in the range of 31–33% and 33–39%, respectively. Biodiesel blends B80 and pure biodiesel of karanj produced more power, and maximum overall efficiency was recorded as compared with diesel fueled generator. The overall efficiency on jatropha-biodiesel-blended fuel were found less than the diesel-fueled generator. The biodiesel processor based on alkali-catalyzed transesterification process can be used for quality biodiesel production from edible and non-edible vegetable oils. This processor can be integrated with rural energy system for domestic and small-scale industrial unit for biodiesel production.     

Influence of fatty acid methyl esters from hydroxylated vegetable oils on diesel fuel lubricity

Current and future regulations on the sulfur content of diesel fuel have led to a decrease in lubricity of these fuels. This decreased lubricity poses a significant problem as it may lead to wear and damage of diesel engines, primarily fuel injection systems. Vegetable oil based diesel fuel substitutes (biodiesel) have been shown to be clean and effective and may increase overall lubricity when added to diesel fuel at nominally low levels. Previous studies on castor oil suggest that its uniquely high level of the hydroxy fatty acid ricinoleic acid may impart increased lubricity to the oil and its derivatives as compared to other vegetable oils. Likewise, the developing oilseed Lesquerella may also increase diesel lubricity through its unique hydroxy fatty acid composition. This study examines the effect of castor and Lesquerella oil esters on the lubricity of diesel fuel using the High-Frequency Reciprocating Rig (HFRR) test and compares these results to those for the commercial vegetable oil derivatives soybean and rapeseed methyl esters.     

Preparation and Evaluation of Jojoba Oil Methyl Esters as Biodiesel and as a Blend Component in Ultra-Low Sulfur Diesel Fuel

The jojoba plant (Simmondsia chinensis L.) produces seeds that contain around 50 to 60 wt.% of inedible long-chain wax esters that are suitable as a potential feedstock for biodiesel (BD) production. Jojoba oil methyl esters (JME) were prepared from acid-catalyzed pretreated jojoba oil in order to evaluate important fuel properties of jojoba-based BD, including kinematic viscosity, cloud point (CP), pour point (PP), cold filter plugging point (CFPP), acid value (AV), oxidative stability, and lubricity. A comparison was made with soybean oil methyl esters (SME) and relevant BD fuel standards such as ASTM D6751 and EN 14214. JME was characterized using Fourier transform infrared spectroscopy and ¹H and ¹³C nuclear magnetic resonance. The CP, PP, and CFPP of JME were ?13°C, ?16°C, and ?14°C, respectively, which were superior to SME. The kinematic viscosity (40°C) of JME was 6.67 mm²/s, which was higher than observed for SME. Blends (B5 and B20) of JME in ultra-low sulfur diesel fuel (ULSD) were also evaluated for the aforementioned fuel properties and compared to an analogous set of blends of SME in ULSD and relevant petro diesel fuel standards such as ASTM D975 and D7467. JME blends in ULSD displayed improved low-temperature properties in comparison to neat ULSD and blends of SME in ULSD. In summary, jojoba oil has potential as an alternative, nonfood feedstock for BD production.     

Effects of biodiesel on emissions of a bus diesel engine

This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel (D2) under various operating regimes. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound velocity are determined experimentally and compared to those of D2. The obtained results are used to analyze the most important injection, fuel spray, and engine characteristics. The injection characteristics are determined numerically under the operating regimes, corresponding to the 13 mode ESC test. The fuel spray is obtained experimentally under peak torque condition. Engine characteristics are determined experimentally under 13 mode ESC test conditions. The results indicate that, by using biodiesel, harmful emissions (NO(x), CO, smoke and HC) can be reduced to some extent by adjusting the injection pump timing properly.     

Lipase-catalyzed biodiesel production from waste activated bleaching earth as raw material in a pilot plant

The production of fatty acid methyl esters (FAMEs) from waste activated bleaching earth (ABE) discarded by the crude oil refining industry using lipase from Candida cylindracea was investigated in a 50-L pilot plant. Diesel oil or kerosene was used as an organic solvent for the transesterification of triglycerides embedded in the waste ABE. When 1% (w/w) lipase was added to waste ABE, the FAME content reached 97% (w/w) after reaction for 12 h at 25 degrees C with an agitation rate of 30 rpm. The FAME production rate was strongly dependent upon the amount of enzyme added. Mixtures of FAME and diesel oil at ratios of 45:55 (BDF-45) and 35:65 (BDF-35) were assessed and compared with the European specifications for biodiesel as automotive diesel fuel, as defined by pr EN 14214. The biodiesel quality of BDF-45 met the EN 14214 standard. BDF-45 was used as generator fuel, and the exhaust emissions were compared with those of diesel oil. The CO and SO2 contents were reduced, but nitrogen oxide emission increased by 10%. This is the first report of a pilot plant study of lipase-catalyzed FAME production using waste ABE as a raw material. This result demonstrates a promising reutilization method for the production of FAME from industrial waste resources containing vegetable oils for use as a biodiesel fuel.     

Biodegradation of diesel/biodiesel blends by a consortium of hydrocarbon degraders: effect of the type of blend and the addition of biosurfactants

Biodegradation experiments for diesel/biodiesel blends in liquid cultures by-petroleum degrading microbial consortium showed that for low amendments of biodiesel (10%) the overall biodegradation efficiency of the mixture after seven days was lower than for petroleum diesel fuel. Preferential usage of methyl esters in the broad biodiesel concentration range and diminished biodegradation of petroleum hydrocarbons for 10% biodiesel blend was confirmed. Rhamnolipids improved biodegradation efficiency only for blends with low content of biodiesel. Emulsion formation experiments showed that biodiesel amendments significantly affected dispersion of fuel mixtures in water. The presence of rhamnolipids biosurfactant affected stability of such emulsions and altered cell surface properties of tested consortium.     

Biodiesel from Corn Distillers Dried Grains with Solubles: Preparation, Evaluation, and Properties

A coproduct of dry-grind ethanol fermentation, corn distillers?? dried grains with solubles (DDGS) represents a low-cost feedstock with potential to integrate production of biodiesel and ethanol. Oil extracted from DDGS was converted into distillers?? grains methyl (DGME) and ethyl (DGEE) esters. Pretreatment using sulfuric acid was effective at lowering the acid value of the crude oil from 27.15 to less than 0.30?mg?KOH?g^?1, thus rendering it amenable to homogenous, base-catalyzed transesterification. Measurement of fuel properties and comparison to refined corn oil methyl (RCME) and ethyl (RCEE) esters revealed that the cold flow properties and oxidative stability of DGME and DGEE were deficient relative to RCME and RCEE. In the absence of antioxidants, DGME and DGEE did not meet the oxidative stability specifications of ASTM D6751 and EN 14214. The cetane number of DGEE was below the minimum limit specified in EN 14214. DGEE exhibited more favorable cold flow properties, iodine value, and energy content than DGME. Evaluation of blends (B5 and B20) in petroleum diesel fuel revealed that antioxidants and cetane enhancers would be required to meet the specifications of the US and European diesel fuel standards. Other fuel properties of the petrodiesel blends were largely neutral with respect to alkyl ester type and conformed to the limits specified in the respective standards.     

The effect of the bioremediation of soil contaminated with petroleum derivatives on the occurrence of epigeic and edaphic fauna

This field study investigated the colonization process of soil contaminated with different petroleum products (petrol, diesel fuel, spent engine oil; dose: 6000 mg of fuel·kg^?1 dry mass [d.m.] of soil) by epigeic and edaphic invertebrates during the progress of natural bioremediation and bioremediation enhanced using selected microorganisms (ZB-01 biopreparation). Epigeic fauna was captured using pitfall traps. Occurrence of edaphic fauna in soil samples as well as total petroleum hydrocarbon contents (TPH) were also investigated. Results showed that inoculation with ZB-01 biocenosis allowed the degradation of petroleum derivatives in the soil contaminated with diesel fuel and engine oil, with 82.3% and 75.4% efficiency, respectively. Applying bioremediation to all contaminated soils accelerated the process of recolonization by edaphic invertebrates. However, the 28-month period was too short to observe full population recovery in soils contaminated with diesel fuel and engine oil. Microbe-enhanced bioremediation accelerated recolonization by epigeic invertebrates on soil contaminated with diesel fuel, whereas it exerted inhibitory effect on recolonization of soil contaminated with engine oil (especially by Collembola). The observed discrepancies in the rates of recolonization for soils contaminated with petrol and diesel fuel that were still noted at the stage of no longer different TPH levels justify the idea to include the survey of edaphic faunal density as one of the parameters in the ecological risk assessment of various bioremediation techniques.     

Incentivising fire management in Pindan (Acacia shrubland): A proposed fuel type for Australia's Savanna burning greenhouse gas emissions abatement methodology

The Australian Government has sanctioned development of greenhouse gas emissions (GHG) abatement methodologies to meet international emissions reduction obligations. Savanna burning emissions abatement methodologies have been available since 2012, and there are currently 72 registered projects covering approximately 32 million ha. Abatement to date has exceeded 4 million tonnes of carbon dioxide equivalent (CO2‐e) principally through the application of low intensity early dry season fire management to reduce the amount of biomass combusted in higher intensity late dry season (LDS) fires. Savanna burning projects can only be conducted on areas with eligible fire‐prone vegetation fuel types where implementing the improved fire management regime is considered ecologically appropriate. This study assesses the suitability of including tall Acacia shrublands (‘Pindan’) as a new eligible fuel type. These shrublands make up 12% (~2 million ha) of the Kimberley region, Western Australia, where, on average, 32% is fire affected annually, mostly in the LDS. A standard assessment protocol was applied to describe vegetation fuel type structural and pyrolysis characteristics. We show that Pindan (i) can be identified and mapped as a unique tall Acacia shrubland vegetation fuel type, (ii) characterised by a significantly greater shrubby fuel load biomass, and (iii) the conservation status of which would benefit from imposition of strategic prescribed burning programme. Savanna burning projects in the Pindan fuel type could potentially abate up to 24.43 t.CO₂‐e/km² per year, generating significant income and employment opportunities for predominantly Indigenous land managers in the region.