Bacterial cellulose production under oxygen-enriched air at different fructose concentrations in a 50-liter, internal-loop airlift reactor

Bacterial cellulose (BC) production by Acetobacter xylinum subsp. sucrofermentans BPR2001 was carried out in a 50-1 internal-loop airlift reactor in air at an initial fructose concentration of 40 g/l. The BC production rate was 0.059 g/l per h. When oxygen-enriched air was supplied instead of air, the BC production rate increased to 0.093 g/l per h, and the BC yield was enhanced from 11% in air to 18%. When the initial fructose concentrations were varied from 30 to 70 g/l, the highest BC yield (35%) the highest production rate (0.22 g/l x per h), and the highest concentration of BC produced (10.4 g/l) were observed at 60-70 g/l fructose. From the carbon mass balance calculated at the final stage of cultivation, it was observed that enhanced BC production was reflected as a decrease in both CO2 evolution and the concentration of other unknown substances, suggesting the efficient utilization of energy for BC synthesis despite O2 limitation.     

Effect of addition of water-soluble polysaccharides on bacterial cellulose production in a 50-L airlift reactor

Bacterial cellulose (BC) production was carried out in a batch cultivation of Acetobacter xylinum in a 50-L internal loop airlift reactor by addition of water-soluble polysaccharides into the medium. When 0.1% (w/w) agar was added, BC production reached 8.7 g/L compared with 6.3 g/L in the control, and duration of the cultivation period to reach the maximum concentration of BC was almost half of that without addition of polysaccharides. During cultivation, BC was formed into pellets whose size was smaller when the productivity of BC was higher, indicating that increase in the relative viscosity by addition of polysaccharides hindered formation of large clumps of BC and increase in the volumetric oxygen transfer coefficient at high flow rate led to increase in BC productivity.     

Effect of addition of sodium alginate on bacterial cellulose production by <Emphasis Type="Italic">Acetobacter xylinum</Emphasis>

Bacterial cellulose (BC) production by Acetobacter xylinum NUST4.1 was carried out in the shake flask and in a stirred-tank reactor by means of adding sodium alginate (NaAlg) into the medium. When 0.04% (w/v) NaAlg was added in the shake flask, BC production reached 6.0 g/l and the terminal yield of the cellulose was 27% of the total sugar initially added, compared with 3.7 g/l and 24% in the control, respectively. The variation between replicates in all determinations was less than 5%. During the cultivation in the stirred-tank reactor, the addition of NaAlg changed the morphology of cellulose from the irregular clumps and fibrous masses entangled in the internals to discrete masses dispersing into the broth, which indicates that NaAlg hinders formation of large clumps of BC, and enhances cellulose yield. Because the structure of cellulose is changed depending on the culture condition such as additives, structural characteristics of BC produced in the NaAlg-free and NaAlg medium are compared using scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD). SEM photographs show some differences in reticulated structures and ribbon width and FT-IR spectra indicate that there is the hydrogen bonding interaction between BC and NaAlg, then X-ray diffraction (XRD) analysis reveals that BC produced with NaAlg-added has a lower crystallinity and a smaller crystalline size. The results show that enhanced yields and modification of cellulose structure occur in the presence of NaAlg.     

Role of water-soluble polysaccharides in bacterial cellulose production

Acetobacter xylinum BPR2001 produces water-insoluble bacterial cellulose (BC) and a water-soluble polysaccharide called acetan in corn steep liquor-fructose medium. Acetobacter xylinum EP1, which is incapable of acetan production was derived by disrupting the aceA gene of BPR2001. The BC production by EP1 (2.88 g/L) was lower than that by BPR2001 (4.6 g/L) in baffled-flask culture. When purified acetan or agar was added to the medium from the start of cultivation, the BC production by EP1 was enhanced and the final BC yield of EP1 was almost the same as that of BPR2001. A similar improvement of BC production by EP1 by the addition of agar was also confirmed by cultivation in a 50-L airlift reactor. From these results, the role of acetan in BC production is associated with the increase in the viscosity of the culture medium which may hinder coagulation of BC and cells in the culture, thereby accelerating the growth of BPR2001 and BC production by BPR2001.     

Utilization of the buffering capacity of corn steep liquor in bacterial cellulose production by Acetobacter xylinum

Acetobacter xylinum BPR2001 produces water-insoluble bacterial cellulose (BC). Using a pH sensor for the accurate control of pH, which is one of the most critical factors for efficient BC production, is difficult especially in a baffled shake-flask and an airlift reactor. The buffering capacity of corn steep liquor (CSL) was estimated by measuring (buffering capacity) values in advance and was used to maintain the pH within the optimal range during the production of BC. When CSL was added to either a shake-flask, a stirred-tank reactor or an airlift reactor, BC production was almost the same as that in cultivations where pH was controlled manually or by a pH sensor.     

Production of thuringiensin from Bacillus thuringiensis using a net-draft-tube,modified airlift reactor

A net-draft-tube, modified airlift reactor and a stirred-tank reactor were used for thuringiensin production by Bacillus thuringiensis subsp. darmstadiensis growing with various concentrations of molasses. The optimum concentration of molasses for thuringiensin production in both reactors was 15 g/l. There was a 6 h delay in sporulation in the modified airlift reactor compared with that in the stirred-tank reactor. Thuringiensin yield in the modified airlift reactor (2.2 g/l) was consequently higher than that in the stirred-tank reactor (1.1 g/l).     

Production of bacterial cellulose by Acetobacter xylinumwith an air-lift reactor

Bacterial cellulose was produced by Acetobacter xylinum subsp. surcrofermentans BPR2001 in a 50 liter air-lift reactor using fructose as the main carbon source. When air was supplied, the production of the cellulose was only 2.3 g/l in 80 h but when O -fortified air was supplied, the cellulose concentration increased to 5.63 g/l in 28 h and the productivity of the cellulose in an air-lift reactor with O -fortified air supply was comparable to that in a mechanically agitated jar fermenter.     

Enhanced production of bacterial cellulose by using a biofilm reactor and its material property analysis

Bacterial cellulose has been used in the food industry for applications such as low-calorie desserts, salads, and fabricated foods. It has also been used in the paper manufacturing industry to enhance paper strength, the electronics industry in acoustic diaphragms for audio speakers, the pharmaceutical industry as filtration membranes, and in the medical field as wound dressing and artificial skin material. In this study, different types of plastic composite support (PCS) were implemented separately within a fermentation medium in order to enhance bacterial cellulose (BC) production by Acetobacter xylinum. The optimal composition of nutritious compounds in PCS was chosen based on the amount of BC produced. The selected PCS was implemented within a bioreactor to examine the effects on BC production in a batch fermentation. The produced BC was analyzed using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA). Among thirteen types of PCS, the type SFYR+ was selected as solid support for BC production by A. xylinum in a batch biofilm reactor due to its high nitrogen content, moderate nitrogen leaching rate, and sufficient biomass attached on PCS. The PCS biofilm reactor yielded BC production (7.05 g/L) that was 2.5-fold greater than the control (2.82 g/L). The XRD results indicated that the PCS-grown BC exhibited higher crystallinity (93%) and similar crystal size (5.2 nm) to the control. FESEM results showed the attachment of A. xylinum on PCS, producing an interweaving BC product. TGA results demonstrated that PCS-grown BC had about 95% water retention ability, which was lower than BC produced within suspended-cell reactor. PCS-grown BC also exhibited higher T _max compared to the control. Finally, DMA results showed that BC from the PCS biofilm reactor increased its mechanical property values, i.e., stress at break and Young's modulus when compared to the control BC. The results clearly demonstrated that implementation of PCS within agitated fermentation enhanced BC production and improved its mechanical properties and thermal stability.     

不同培养方式对细菌纤维素产量和结构性质的影响

考察了自行筛选的Acetobacter xylinum NUST4.2在静置培养和发酵罐培养获得的细菌纤维素(BC)的产量、基本结构和性能的差异。结果表明:静置培养时产纤维素7.5g/L,产率为0.052g/L/h,在机械搅拌发酵罐中培养3d产量达3.13g/L,产率达0.043g/L/h;SEM分析显示静置培养和发酵罐培养得到的纤维素均具有网状结构,但静置获得的纤维素丝带相互缠绕且层状重叠,更加致密,丝带更细;FT-IR分析知搅拌不改变纤维素的化学结构,但能减弱分子间氢键,和XRD结合分析可知静置培养的纤维素具有更高结晶指数,更高Iα含量和更大晶粒尺寸,但不改变晶型,仍为纤维素I型,说明搅拌会干扰纤维素初始纤丝的结晶,有利于形成更小的晶粒和较Iα稳定的Iβ。与棉纤维素相比,静置培养获得的纤维素的热稳定性更好,而发酵罐培养获得的纤维素则阻燃性更好。     

Simultaneous nitrification-denitrification achieved by an innovative internal-loop airlift MBR: comparative study

This study assessed the performance of different single-stage continuous aerated submerged membrane bioreactors (MBR) for nitrogen removal. Almost complete nitrification was achieved in each MBR irrespective of operating mode and biomass system. Denitrification was found to be the rate-limiting step for total nitrogen (T-N) removal. The MBR with internal-loop airlift reactor (ALR) configuration performed better as regards T-N removal compared with continuous stirred-tank reactor (CSTR). It was demonstrated that simultaneous nitrification and denitrification (SND) is the mechanism leading to nitrogen removal and the contribution of microenvironment on SND is more remarkable for the MBRs with hybrid biomass. Macroenvironment analyses showed that gradient distribution of dissolved oxygen (DO) level in airlift MBRs imposed a significant effect on SND. Higher mixed liquor suspended solid (MLSS) concentration led to the improvement in T-N removal by enhancing anoxic microenvironment. Apparent nitrite accumulation coupled with higher nitrogen reduction was accomplished at MLSS concentration exceeded 12.6 g/L.     

Effects of CMC addition on bacterial cellulose production in a biofilm reactor and its paper sheets analysis

Bacterial cellulose (BC) can be grown into any desired shape such as pellicles, pellets, and spherelike balls, depending on the cultivation method, additives, and cell population. In this study, Acetobacter xylinum (ATCC 700178) was grown in the production medium with different concentrations of carboxylmethylcellulose (CMC) and were evaluated for BC production by using a PCS biofilm reactor. The results demonstrated that BC production was enhanced to its maximum (～13 g/L) when 1.5% of CMC was applied, which was 1.7-fold higher than the result obtained from control culture. The major type of the produced BC was also switched from BC pellicle to small pellets. The ratio of BC pellets in suspension increased from 0 to 93%. Fourier transform infrared (FTIR) spectroscopy demonstrated that CMC was incorporated into BC during fermentation and resulted in the decreased crystallinity and crystal size. The X-ray diffraction (XRD) patterns indicated that CMC-BC exhibited both lower crystallinity (80%) and crystal size (4.2 nm) when compared with control samples (86% and 5.3 nm). The harvested BC was subjected to paper formation and its mechanical strength was determined. Dynamic mechanical analysis (DMA) results demonstrated that BC paper sheets exhibited higher tensile strength and Young's modulus when compared with regular paper.     

以玉米浆和木薯为原料机械搅拌发酵制备细菌纤维素的研究

本文以玉米浆和木薯为原料,用机械搅拌式发酵罐制备细菌纤维素（BC）,对发酵过程的纤维素产量、还原糖消耗、溶氧变化和茵浓变化进行了监测,并以葡萄糖一蛋白胨-酵母粉培养基为对照进行了比较。实验得出玉米浆作氮源时不溶BC的产量为9．2g／L,而氮源成本只是对照组的15％;木薯水解液作碳源时的不溶BC产量达到11．7g／L,比对照组（10．8g／L）高8％;而用玉米浆搭配木薯水解液发酵生产BC,产量也达到10．1g／L,验证了这两种天然原料的廉价高效性,用于工业生产细菌纤维素具有良好的前景。     

Strategies for penicillin fermentation in tower-loop reactors

Since it has not been possible to produce penicillin in tower-loop reactors with highly viscous filamentous molds of Penicillium chrysogenum which are employed in stirred-tank reactors, a new strategy has been developed to avoid the formation of this morphology and to use the pellet form of the fungi. When employing definite impeller speeds in the subculture in connection with definite inoculum amounts and substrate concentrations in the main culture (bubble column), it is possible to generate a suspension of isolated small pellets, which shows a low broth viscosity up to a sediment content of 45% over the entire fermentation time. Volumetric mass-transfer coefficients k(L)as are by a factor of 4 to 5 higher in these pellet suspensions than in filamentous broths. It was easy to maintain the necessary oxygen supply for penicillin production in these pellet suspensions. Under these conditions the specific penicillin productivities were higher with regard to power input (up to 90%), biomass, and consumed substrate than in the stirred-tank reactors with highly viscous filamentous morphology of the fungi. Under nonoptimized operating conditions the absolute penicillin production in the tower loop was 35% lower than in the stirred-tank reactor due to lower possible biomass concentrations. The separation of the biomass, and therefore the penicillin recovery, is much simpler when employing pellets. It is shown how the particular mass transfer resistances at the gas/liquid and liquid/pellet interfaces and within the pellets change with the pellet diameter. There should be a particular pellet diameter at which penicillin productivity has its maximum. These investigations indicate that the use of tower-loop reactors can, in the future, be an alternative for more economical penicillin production methods.     

Processing characteristics of submerged fermentation of Antrodia cinnamomea in airlift bioreactor

Three 5-L airlift bioreactors including airlift reactor with solid draft tube (ALs), airlift reactor with net draft tube (ALn) and bubble column reactor (BC) were investigated for their suitability for cultivating Antrodia cinnamomea, and a stirred tank reactor (ST) was used for comparison. Results indicated that after 7 days fermentation, ALs yielded the highest mycelium content (313 mg/100 mL) and had the lowest dissolved oxygen in the broth. Among different aeration rates (0.025, 0.05, 0.1, 0.5, 1 vvm) used during cultivation of A. cinnamomea in ALs, the aeration rate 0.1 vvm resulted in a volumetric oxygen transfer coefficient of 10.8 h⁻¹ and produced the highest mycelium content. When the optimal conditions were used for the fermentation of A. cinnamomea in an industrial 500-L ALs, the mycelium content in the broth reached 542 mg/100 mL in 28 days. The IC₅₀ values of the ethanol extracts of A. cinnamomea mycelium cultivated in 5-L and 500-L ALs for 28 days were 23 and 17 μg/mL, respectively, for hepatocellular carcinoma cells HepG2. And after 42 days cultivation in 500-L ALs, the IC₅₀ value of the mycelium ethanol extract was reduced to 10 μg/mL.     

新型气升式反应器在发酵培养中的应用研究

本文以Ｌ－苹果酸生产为例,采用新型的分段内循环气升式反应器分批培养产延胡索酸酶的产氨短杆菌ＭＡ－２,并与同等规模机械搅拌反应器中接着的结果相比较。数据表明,采用气升式发酵设备进行培养,该菌体的收率能提高近３％,且发酵周期能缩短一半左右,显著降低培养成本,该类型的反应器具有广阔的应用前景。     

Improvement of Panax notoginseng cell culture for production of ginseng saponin and polysaccharide by high density cultivation in pneumatically agitated bioreactors

A Panax notoginseng cell culture was successfully scaled up from shake flask to 1.0-L bubble column reactor and concentric-tube airlift reactor. High-density bioreactor batch cultivation was carried out using a modified MS medium. The maximum cell density in batch cultures reached 20.1, 21.0 and 24.1 g/L in the shake flask, bubble column and airlift reactors, respectively, and their corresponding biomass productivity was 950, 1140 and 1350 mg/(L x d) for each. The productivity of ginseng saponin was 70, 96 and 99 mg/(L x d) in the flask, bubble column and airlift reactors, respectively; and the polysaccharide productivity reached 104, 119 and 151 mg/(L x d) for each. Furthermore, a fed-batch cultivation strategy was developed on the basis of specific oxygen uptake rate (SOUR), i.e., sucrose feeding before a sharp decrease of SOUR, and the highest cell density of 29.7 g/L was successfully achieved in the airlift bioreactor on day 17 with a very high biomass productivity of 1520 mg/(L x d). The concentrations of ginseng saponin and polysaccharide reached about 2.1 and 3.0 g/L, respectively, and their productivity was 106 (saponin) and 158 mg/(L x d) (polysaccharide). This work successfully demonstrated the high-density bioreactor cultivation of P. notoginseng cells in pneumatically agitated bioreactors and the reproduction of the shake flask culture results in bioreactors. The cell density, biomass productivity, production titer and productivity of both ginseng saponin and polysaccharide obtained here were the highest that have been reported on a reactor scale for all the ginseng species.     

Production of exopolysaccharides by submerged mycelial culture of a mushroom Tremella fuciformis

The optimization of submerged culture conditions for mycelial growth and exopolysaccharide (EPS) production in an edible mushroom Tremella fuciformis was studied in shake flasks and bioreactors. The temperature of 28 degrees C and pH 8 in the beginning of fermentation in agitated flasks was the most efficient condition to obtain maximum mycelial biomass and EPS. The optimal medium constituents were as follows (gL(-1)): glucose 20, tryptone 2, KH(2)PO(4) 0.46, K(2)HPO(4) 1 and MgSO(4).7H(2)O 0.5. The fungus was cultivated under various agitation and aeration conditions in a 5L stirred-tank bioreactor. The maximum cell mass and EPS production were obtained at a relatively high agitation speed of 200 rpm and at an aeration rate of 2 vvm. The flow behavior of the fermentation broth was Newtonian and the maximum apparent viscosity (35 cP) was observed at a highly aerated condition (2 vvm). The EPS productivity in an airlift reactor was higher than that in the stirred-tank reactor. The morphological study revealed that the fungus grows in mainly three different yeast-like forms: ovoid, elongated, and double yeast forms. The high population of the elongated yeast has a very close relationship to high EPS production. The EPS were protein-bound polysaccharides consisted of mainly mannose, xylose, and fucose. The molecular weights of EPS were determined to be (1.3-1.5)x10(6).     

Enhanced continuous production of lovastatin using pellets and siran supported growth of Aspergillus terreus in an airlift reactor

Lovastatin, a hypocholesterolemic agent, is a secondary metabolite produced by filamentous microorganism Aspergillus terreus in submerged batch cultivation. Lovastatin production by pellets and immobilized siran cells was investigated in an airlift reactor. The process was carried out by submerged cultivation in continuous mode with the objective of increasing productivity using pellet and siran supported growth of A terreus. The continuous mode of fermentation improves the rate of lovastatin production. The effect of dilution rate and aeration rate were studied in continuous culture. The optimum dilution rate for pellet was 0.02 h⁻¹ and for siran carrier was 0.025 h⁻¹. Lovastatin productivity using immobilized siran carrier (0.0255 g/L/h) was found to be greater than pellets (0.022 g/L/h). The productivity by both modes of fermentation was found higher than that of batch process which suggests that continuous cultivation is a promising strategy for lovastatin production.     

Repeated-batch culture of immobilizedGibberella fujikuroi B9 for gibberellic acid production: An optimization study

The performance of immobilized fungal cells on celite beads for the production of gibberrelic acid was investigated in flasks and 7-L stirred-tank reactor. Repeated incubations of immobilized fungal cells increased cell concentrations and volumetric productivity. The maximum volumetric productivity obtained in the immobilized-cell culture was 3-fold greater than that in suspended-cell culture. The concentration of cotton seed flour (CSF), amont the various nutrients supplied, most significantly influenced productivity and operational stability. Notably, insoluble components in CSF were found to be essential for production. CSF at 6 g/L with 60 g/L glucose was found to be optimal for gibberellic acid production and stable operation by preventing excessive cell growth.     

Cultivation of Tetrahymena thermophila in a 1.5-m3 airlift bioreactor

A large-scale cultivation system for the mass cell production and extraction of the protozoon Tetrahymena thermophila has been developed on the basis of a low-cost complex nutrient medium. Cell growth and the production of extracellular proteases were investigated using a 15-l stirred-tank reactor and 13-l and 1500-l airlift reactors. Processes using defined and complex medium formulations were compared. After cell mass production by 1200 l cell suspension in the large airlift bioreactor, two different extraction methods, based on the use of an extraction decanter and a sedimentation procedure, were compared and followed by cell lyophilization. Cell sedimentation was shown to be the more efficient extraction method as it enabled cell retention/separation while preserving the cell structure. Maximum cell growth was achieved in the stirred-tank bioreactor, supporting the hypothesis that higher shear forces reduce the particle size of the medium, which is responsible for an optimized nutrient supply. The highest glucose uptake rates were found in defined medium lacking the nutrient particles that are present in complex medium formulations. The cell-specific proteolytic activity in culture supernatants of airlift bioreactors using complex medium conditions was higher than that of a culture broth with cells grown under defined medium formulations. Received: 24 September 1998 / Received revision: 23 November 1998 / Accepted: 29 November 1998