Theoretical and Numerical Approaches for Determining the Reflection and Transmission Coefficients of OPEFB-PCL Composites at X-Band Frequencies

Bio-composites of oil palm empty fruit bunch (OPEFB) fibres and polycaprolactones (PCL) with a thickness of 1 mm were prepared and characterized. The composites produced from these materials are low in density, inexpensive, environmentally friendly, and possess good dielectric characteristics. The magnitudes of the reflection and transmission coefficients of OPEFB fibre-reinforced PCL composites with different percentages of filler were measured using a rectangular waveguide in conjunction with a microwave vector network analyzer (VNA) in the X-band frequency range. In contrast to the effective medium theory, which states that polymer-based composites with a high dielectric constant can be obtained by doping a filler with a high dielectric constant into a host material with a low dielectric constant, this paper demonstrates that the use of a low filler percentage (12.2%OPEFB) and a high matrix percentage (87.8%PCL) provides excellent results for the dielectric constant and loss factor, whereas 63.8% filler material with 36.2% host material results in lower values for both the dielectric constant and loss factor. The open-ended probe technique (OEC), connected with the Agilent vector network analyzer (VNA), is used to determine the dielectric properties of the materials under investigation. The comparative approach indicates that the mean relative error of FEM is smaller than that of NRW in terms of the corresponding S₂₁ magnitude. The present calculation of the matrix/filler percentages endorses the exact amounts of substrate utilized in various physics applications.     

Dielectric properties of human brain tissue measured less than 10 h postmortem at frequencies from 800 to 2450 MHz

The dielectric properties of gray matter in the frequency range of 800-2450 MHz were measured on 20 human brains immediately after excision, less than 10 h after death. The brains were obtained during autopsy of 10 male and 10 female humans who died at ages between 47.5 and 87.5 years [70.4 +/- 9.8 years, mean +/- standard deviation (SD)]. The tissue temperature at the measurement sites ranged between 18 and 25 degrees C (21.35 +/- 1.6 degrees C, mean +/- SD). On each brain, four specific locations on the temporal lobe were measured on the right and left sides, i.e., 160 different measurements of the dielectric properties were performed. The dielectric probe was placed on the intact arachnoid on a gyrus in the selected area. The measurements yielded a mean value (+/-SD) of gray matter equivalent conductivity of 1.13 +/- 0.12 and 2.09 +/- 0.16 S/m at 800 and 2450 MHz, respectively. The mean value of measured relative permittivity was 58.2 +/- 3.3 and 54.7 +/- 3.3 at 800 and 2450 MHz, respectively. Taking into account a positive temperature coefficient of equivalent conductivity, these measurements indicate that the equivalent conductivity of human gray matter at body temperature is somewhat higher than today's generally accepted value, which is based on measurements on animal tissue and excised samples of human tissue measured more than 24 h postmortem.     

Transient changes during microwave ablation simulation : a comparative shape analysis

Microwave ablation therapy is a hyperthermic treatment for killing cancerous tumours whereby microwave energy is dispersed into a target tissue region. Modelling can provide a prediction for the outcome of ablation, this paper explores changes in size and shape of temperature and Specific absorption rate fields throughout the course of simulated treatment with different probe concepts. Here, an axisymmetric geometry of a probe embedded within a tissue material is created, solving coupled electromagnetic and bioheat equations using the finite element method, utilizing hp discretisation with the NGSolve library. Results show dynamic changes across all metrics, with different responses from different probe concepts. The sleeve probe yielded the most circular specific absorption rate pattern with circularity of 0.81 initially but suffered the largest reduction throughout ablation. Similarly, reflection coefficients differ drastically from their initial values, with the sleeve probe again experiencing the largest change, suggesting that it is the most sensitive the changes in the tissue dielectric properties in these select probe designs. These collective characteristic observations highlight the need to consider dielectric property changes and probe specific responses during the design cycle.

     

Reflection and absorption of millimeter waves by thin absorbing films

Reflection, transmission, and absorption of mm-waves by thin absorbing films were determined at two therapeutic frequencies: 42. 25 and 53.57 GHz. Thin filter strips saturated with distilled water or an alcohol-water solution were used as absorbing samples of different thicknesses. The dependence of the power reflection coefficient R(d) on film thickness (d) was not monotonic. R(d) passed through a pronounced maximum before reaching its steady-state level [R(infinity)]. Similarly, absorption, A(d), passed two maximums with one minimum between them, before reaching its steady-state level [A(infinity)]. At 42.25 GHz, A(d) was compared with absorption in a semi-infinite water medium at a depth d. When d < 0.3 mm, absorption by the film increased: at d = 0.1 mm the absorption ratio for the thin layer sample and the semi-infinite medium was 3.2, while at d = 0.05 mm it increased up to 5.8. Calculations based on Fresnel equations for flat thin layers adequately described the dependence of the reflection, transmission, and absorption on d and allowed the determination of the refractive index (n), dielectric constant (epsilon), and penetration depth (delta) of the absorbing medium for various frequencies. For water samples, epsilon was found to be 12.4-19.3j, delta = 0.49 mm at 42.25 GHz, and epsilon = 9.0-19.5j, delta = 0.36 mm at 53.57 GHz. The calculated power density distribution within the film was strongly dependent on d. The measurements and calculations have shown that the reflection and absorption of mm-waves by thin absorbing layers can significantly differ from the reflection and absorption in similar semi-infinite media. The difference in reflection, absorption, and power density distribution in films, as compared to semi-infinite media, are caused by multiple internal reflections from the film boundaries. That is why, when using thin phantoms and thin biological samples, the specifics of the interaction of mm-waves with thin films should be taken into account.     

Microwave absorption by folded DNA chains

Absorption of radiation by DNA polymer is calculated for the case of bent polymer chains. The molecule is assumed to be straight except for localized bends. The region between two bends is studied in particular. The vibrational properties of the bends are parameterized by a transmission and a reflection coefficient. A general Green function expression for absorption is studied for various values of the damping rate, as well as the transmission/reflection coefficients. Curves of absorption vs frequency are shown for a number of cases.     

The Plasmon–Plasmon Coupling in a System of a Dielectric Slab Doped with Silver Nano-spheres Sandwiched Between Two Silver Parallel Plates

I compute the transmission coefficient as function of the incident light frequency for a system consisting of a dielectric slab doped with silver nano-spheres sandwiched between two silver parallel plates. Then, I analyze the details of the transmission spectrum identifying the coupled plasmons from the two (doped dielectric and plates) subsystems which dominate the system’s dynamics.     

Diurnal variation in the radial reflection coefficient of intact maize roots determined with the xylem pressure probe

Xylem pressure and its relative response to the imposition ofan external osmotic stress (the so-called radial reflectioncoefficient) were recorded in roots of intact maize plants usingthe xylem pressure probe technique. Consecutive insertion oftwo probes into the same xylem vessel or into adjacent vesselsof intact roots of plants exposed to high light intensity andsalt stress under laboratory conditions showed that the xylemtension was not changed by vessel probing. It was also shownby using the double probe approach that the plants were capableof overcoming artificially induced leakages. This and otherevidence reported in the literature convincingly demonstratedthat the probe accurately reads xylem pressure and xylem pressureresponses to osmotic stress. Additional experiments were performedon plants grown in a greenhouse at a subtropical latitude. Underthese conditions the plants were exposed to strong diurnal fluctuationsin light intensity, relative humidity and temperature. The resultsshowed that the absolute xylem pressure in the roots of untreatedplants decreased with increasing transpiration rate from positivevalues in the early morning to negative values around noon (averagevalue –0.15 MPa; maximum negative value –0.57 MPa).As the day progressed and the transpiration rate decreased,xylem pressure increased again to positive values. Correspondingly,the radial reflection coefficient for NaCI increased from aboutzero in the early morning to about unity at noon when transpirationreached its highest value and decreased again to very low valuestowards the evening. The data raise questions concerning conclusionsabout the mechanism of water transport in intact roots drawnfrom the low radial reflection coefficients measured on excisedroots using the root pressure probe. Key words: Xylem pressure probe, osmotic stress, reflection coefficient, transpiration, diurnal changes     

Theoretical and experimental study of microwave power absorption by a single-sided multipactor discharge on a dielectric

The coefficient of microwave power absorption by a single-sided multipactor discharge on a dielectric surface is studied analytically and numerically as a function of the incident microwave power. It is shown that taking into account electron reflections from the dielectric surface leads to a substantial increase in the absorption coefficient. The analytical and numerical results are compared with experimental data.     

Neutralization of radiation damping by selective feedback on a 400 MHz NMR spectrometer

Summary Radiation damping is a phenomenon well known among NMR spectroscopists of proteins as a source of undesirable features, especially in high-field and high-Q probe NMR. In this paper, we present an electronic neutralization network which dramatically reduces radiation damping. It detects the radiation field profile and feeds back into the probe an rf field with identical amplitude and opposite phase. Experimental results of a practical implementation carried out on a 400 MHz Bruker spectrometer are shown.     

Reliable Method for Fabricating Tissue‐Mimicking Materials With Designated Relative Permittivity and Conductivity at 128 MHz

Artificial materials that can simultaneously mimic the relative permittivity and conductivity of various human tissues are usually used in medical applications. However, the method of precisely designing these materials with designated values of both relative permittivity and conductivity at 3 T MRI resonance frequency is lacking. In this study, a reliable method is established to determine the compositions of artificial dielectric materials with designated relative permittivity and conductivity at 128 MHz. Sixty dielectric materials were produced using oil, sodium chloride, gelatin, and deionized water as the main raw materials. The dielectric properties of these dielectric materials were measured using the open‐ended coaxial line method at 128 MHz. Nonlinear least‐squares Marquardt–Levenberg algorithm was used to obtain the formula, establishing the relationship between the compositions of the dielectric materials and their dielectric properties at 128 MHz. The dielectric properties of the blood, gall bladder, muscle, skin, lung, and bone at 128 MHz were selected to verify the reliability of the obtained formula. For the obtained formula, the coefficient of determination and the expanded uncertainties with a coverage factor of k = 2 were 0.991% and 4.9% for relative permittivity and 0.992% and 6.4% for conductivity. For the obtained artificial materials measured using the open‐ended coaxial line method, the maximal difference of relative permittivity and conductivity were 1.0 and 0.02 S/m, respectively, with respect to the designated values. In conclusion, the compositions of tissue‐mimicking material can be quickly determined after the establishment of the formulas with the expanded uncertainties of less than 10%. Bioelectromagnetics. 2021;42:86–94. © 2020 Bioelectromagnetics Society.     

Contributions to the mathematical biophysics of branched circulatory systems

A derivation is given of the reflection coefficient of pressure waves in a vessel whose end branches into many smaller vessles. This coefficient depends on the number of these smaller vessels and their sizes relative to the size of the main vessel. Estimations are made of the order of magnitude of the coefficient. Assuming the main vessel to be of the order of size of an artery, it is shown that the reflection coefficient has a value close to one for reflections at branchings into vessels of arteriolar size. It is pointed out that the result may support the idea that the standing waves in the arterial system are due to reflections at the site of the arterioles.     

"Resonances" in the dielectric absorption of DNA?

An attempt was made to confirm previous reports of resonant-like dielectric absorption of plasmid DNA in aqueous solutions at 1-10 GHz. The dielectric properties of the sample were measured using an automatic network analyzer with two different techniques. One technique used an open-ended coaxial probe immersed in the sample; the other employed a coaxial transmission line. No resonances were observed that could be attributed to the sample; however, resonance-type artifacts were prominent in the probe measurements. The coaxial line technique appears to be less susceptible to such artifacts. We note two important sources of error in the calibration of the automatic network analyzer using the probe technique.     

Discoveries and Explorations of Mode Splitting Phenomenon in Lossy Dielectric Waveguide

We discovered that a specific transmission mode in the fiber waveguide will split into two modes at near cut-off conditions when the fiber is coated with lossy dielectric nanofilms with higher refractive index. One of the two splitting modes is high lossy while the other is slightly lossy. We defined the “mode splitting coefficient” to describe the degree of mode splitting. We found that the biggest mode splitting coefficient was obtained at the mode cut-off wavelength using finite element method. Finally, we put forward an explanation towards the mode splitting phenomenon and expounded the relationship between the mode splitting and mode coupling.

     

Experimental Determination of the Far-Infrared Optical Properties of Biological Matter in Aqueous Solution

Experimental details are given of how to reliably measure theoptical properties of aqueous solutions in the far-infraredspectral range using a Fourier transform spectrometer. We discussthe analysis of reflection and transmission data in order toobtain the refractive index and the absorption coefficient. Someresults on water and biological systems are presented.     

Effect of pierced metallic objects on SAR distributions at 900 MHz

A study of the interaction between mobile phone antennas and a human head in the presence of different types of metallic objects, attached and pierced to the compressed ear, is presented in this article. Computed and measured results have been performed by considering a quasi-half-wavelength dipole as the radiating source and measurements with the DASY4 dosimetric assessment system. Two different human head models have been implemented: a homogeneously shaped sphere and a three-level head model with four different kinds of tissue. Antenna input impedance, reflection coefficient, radiation patterns, SAR distribution, absorbed power, and peak SAR values have been computed and measured for diverse scenarios, electromagnetic simulators, and organs. Despite the measuring accuracy limitations of the study, both simulated and measured results suggest that special attention has to be paid to peak SAR averaged values when wearing metallic objects close to the radiation source, since some increment of peak SAR averaged values is expected.     

Dielectric properties of aqueous solutions of sonicated DNA above 40 MHz

The dielectric properties of sonicated calf-thymus DNA sodium salt in aqueous solutions have been studied in the frequency range from 40 MHz to 2 GHz by time domain spectroscopy (TDS). A dielectric dispersion not previously reported was found, which has a characteristic frequency of about 150 MHz. All of the dielectric parameters are insensitive to the size of DNA fragments and to helix-to-coil transitions. The study of this dispersion as a function of DNA concentration and temperature allows us to conclude that it may be due to counterion fluctuation on short sections, probably in a direction transverse to the macromolecular axis.     

Wave Transmission through an Assembly of Randomly Branching Elastic Tubes

Calculations are presented of the transmission of oscillations through an assembly of randomly branching elastic tubes, as a model of not only the major arteries, but also a peripheral vascular bed. It appears that the viscosity of the arterial wall must be the major source of attenuation in the larger arteries, while the viscosity of the blood plays a significant role only in the smaller vessels. In all situations, variations of cross-sectional area have a considerable effect on wave transmission, causing a general decrease in amplitude and an accentuation of reflection from the terminations. The effects of variation in cross-sectional area are sufficiently great to indicate that they should be included in future models of the arterial system. Finally, it is argued that because of the presence of random branching and elastic nonuniformity, the determination of the reflection coefficient for a system such as the arterial tree may be quite misleading.     

Influence of the outer-magnetospheric magnetohydrodynamic waveguide on the reflection of hydromagnetic waves from a shear flow at the magnetopause

The coefficient of reflection of a fast magnetosonic wave incident on the magnetosphere from the solar wind is studied analytically in the framework of a plane-stratified model of the medium with allowance for the transverse inhomogeneity of the magnetosphere and a jump of the plasma parameters at the magnetopause. Three factors decisively affecting the properties of reflection are taken into account: the shear flow of the solar wind plasma relative to the magnetosphere; the presence of a magnetospheric magnetohydrodynamic waveguide caused by the transverse plasma inhomogeneity; and the presence of an Alfvén resonance deep in the magnetosphere, where the oscillation energy dissipates. If the solar wind velocity exceeds the wave phase velocity along the magnetopause, then the wave energy in the solar wind is negative and such a wave experiences overreflection. In the opposite case, the wave energy is positive and the wave is reflected only partially. The wave reflection has a pronounced resonant character: the reflection coefficient has deep narrow minima or high narrow maxima at the eigenfrequencies of the magnetospheric waveguide. For other frequencies, the reflection coefficient only slightly differs from unity. The wave energy influx into the magnetosphere is positive for waves with both positive and negative energies. For waves with a negative energy, this is a consequence of their overreflection, because the flux of negative energy carried away by the reflected wave exceeds the incident flux of negative energy.     

A surface plasmon resonance probe with a novel integrated reference sensor surface

A surface plasmon resonance (SPR) sensor probe with integrated reference surface is described. In order to fabricate the integrated reference surface, two dielectric layers with different thickness were deposited on the single gold SPR sensor surface via plasma polymerization of hexamethyldisiloxane. The working sensor surface was a 34 nm dielectric layer with immobilized bovine serum albumin (BSA) antigen and an adjacent thin 1 nm dielectric layer without BSA provided reference surface. A specific immunoreaction of anti-BSA antibody was detected after immersion of the SPR probe into sample solution. Simultaneous observation of reference and working surface response enabled determination of the immunoreaction without the need for the baseline measurement. Moreover, compensation of nonspecific adsorption could be confirmed using anti-human serum albumin antibody.