Gait Study and Pattern Generation of a Starfish-Like Soft Robot with Flexible Rays Actuated by SMAs

This paper presents the design and development of a starfish-like soft robot with flexible rays and the implementation of multi-gait locomotion using Shape Memory Alloy （SMA） actuators. The design principle was inspired by the starfish, which possesses a remarkable symmetrical structure and soft internal skeleton. A soft robot body was constructed by using 3D printing technology. A kinematic model of the SMA spring was built and developed for motion control according to displacement and force requirements. The locomotion inspired from starfish was applied to the implementation of the multi-ray robot through the flexible actuation induced multi-gait movements in various environments. By virtue of the proposed ray control patterns in gait transition, the soft robot was able to cross over an obstacle approximately twice of its body height. Results also showed that the speed of the soft robot was 6.5 times faster on sand than on a clammy rough terrain. These experiments demonstrated that the bionic soft robot with flexible rays actuated by SMAs and multi-gait locomotion in proposed patterns can perform successfully and smoothly in various terrains.     

Shape memory alloy-based small crawling robots inspired by C. elegans

Inspired by its simple musculature, actuation and motion mechanisms, we have developed a small crawling robot that closely mimics the model organism of our choice: Caenorhabditis elegans. A thermal shape memory alloy (SMA) was selected as an actuator due to the similarities of its properties to C. elegans muscles. Based on the anatomy of C. elegans, a 12-unit robot was designed to generate a sinusoidal undulating motion. Each body unit consisting of a pair of SMA actuators is serially connected by rigid links with an embedded motion control circuit. A simple binary operation-based motion control mechanism was implemented using a microcontroller. The assembled robot can execute C. elegans-like motion with a 0.17 Hz undulation frequency. Its motion is comparable to that of a real worm.     

Dynamics and stability of lateral plane locomotion on inclines

An actuated, lateral leg spring model is developed to investigate lateral plane locomotion dynamics and stability on inclines. A single actuation input, the force-free leg length, is varied in a feedforward fashion to explicitly and implicitly match prescribed lateral and fore-aft force profiles, respectively. Forward dynamic simulations incorporating the prescribed leg actuation are employed to identify periodic orbits for gaits in which the leg acts to either push the body away from or pull the body towards the foot placement point. Gait stability and robustness to external perturbation are found to vary significantly as a function of slope and velocity for each type of leg function. Results of these analyses suggest that the switch in leg function from pushing to pulling is governed by gait robustness, and occurs at increasing inclines for increasing velocities.     

Another Lesson from Plants: The Forward Osmosis-Based Actuator

Osmotic actuation is a ubiquitous plant-inspired actuation strategy that has a very low power consumption but is capable of generating effective movements in a wide variety of environmental conditions. In light of these features, we aimed to develop a novel, low-power-consumption actuator that is capable of generating suitable forces during a characteristic actuation time on the order of a few minutes. Based on the analysis of plant movements and on osmotic actuation modeling, we designed and fabricated a forward osmosis-based actuator with a typical size of 10 mm and a characteristic time of 2–5 minutes. To the best of our knowledge, this is the fastest osmotic actuator developed so far. Moreover, the achieved timescale can be compared to that of a typical plant cell, thanks to the integrated strategy that we pursued by concurrently addressing and solving design and material issues, as paradigmatically explained by the bioinspired approach. Our osmotic actuator produces forces above 20 N, while containing the power consumption (on the order of 1 mW). Furthermore, based on the agreement between model predictions and experimental observations, we also discuss the actuator performance (including power consumption, maximum force, energy density and thermodynamic efficiency) in relation to existing actuation technologies. In light of the achievements of the present study, the proposed osmotic actuator holds potential for effective exploitation in bioinspired robotics systems.     

Motion analysis of an articulated locomotion model by video and telemetric data.

Traditional techniques of human motion analysis use markers located on body articulations. The position of each marker is extracted from each image. Temporal and kinematic analysis is given by matching these data with a reference model of the human body. However, as human skin is not rigidly linked with the skeleton, each movement causes displacements of the markers and induces uncertainty in results. Moreover, the experiments are mostly conducted in restricted laboratory conditions. The aim of our project was to develop a new method for human motion analysis which needs non-sophisticated recording devices, avoids constraints to the subject studied, and can be used in various surroundings such as stadiums or gymnasiums. Our approach consisted of identifying and locating body parts in image, without markers, by using a multi-sensory sensor. This sensor exploits both data given by a video camera delivering intensity images, and data given by a 3D sensor delivering in-depth images. Our goal, in this design, was to show up the feasibility of our approach. In any case the hardware we used could facilitate an automated motion analysis. We used a linked segment model which referred to Winter's model, and we applied our method not on a human subject but on a life size articulated locomotion model. Our approach consists of finding the posture of this articulated locomotion model in the image. By performing a telemetric image segmentation, we obtained an approximate correspondence between linked segment model position and locomotion model position. This posture was then improved by injecting segmentation results in an intensity image segmentation algorithm. Several tests were conducted with video/telemetric images taken in an outdoor surrounding with the articulated model. This real life-size model was equipped with movable joints which, in static positions, described two strides of a runner. With our fusion method, we obtained relevant limbs identification and location for most postures.     

Mechanics of Undulatory Swimming in a Frictional Fluid

The sandfish lizard (Scincus scincus) swims within granular media (sand) using axial body undulations to propel itself without the use of limbs. In previous work we predicted average swimming speed by developing a numerical simulation that incorporated experimentally measured biological kinematics into a multibody sandfish model. The model was coupled to an experimentally validated soft sphere discrete element method simulation of the granular medium. In this paper, we use the simulation to study the detailed mechanics of undulatory swimming in a “granular frictional fluid” and compare the predictions to our previously developed resistive force theory (RFT) which models sand-swimming using empirically determined granular drag laws. The simulation reveals that the forward speed of the center of mass (CoM) oscillates about its average speed in antiphase with head drag. The coupling between overall body motion and body deformation results in a non-trivial pattern in the magnitude of lateral displacement of the segments along the body. The actuator torque and segment power are maximal near the center of the body and decrease to zero toward the head and the tail. Approximately 30% of the net swimming power is dissipated in head drag. The power consumption is proportional to the frequency in the biologically relevant range, which confirms that frictional forces dominate during sand-swimming by the sandfish. Comparison of the segmental forces measured in simulation with the force on a laterally oscillating rod reveals that a granular hysteresis effect causes the overestimation of the body thrust forces in the RFT. Our models provide detailed testable predictions for biological locomotion in a granular environment.     

Sleeve Muscle Actuator: Concept and Prototype Demonstration

This paper presents the concept and prototype demonstration results of a new sleeve muscle actuator, which provides a significantly improved performance through a fundamental structural change to the traditional pneumatic muscle. Specifically, the sleeve muscle incorporates a cylindrical insert to the center of the pneumatic muscle, and thus eliminates the central portion of the internal volume. Through the analysis of the actuation mechanism, it is shown that the sleeve muscle is able to provide a consistent increase of force capacity over the entire range of motion. Furthermore, the sleeve muscle provides a significant energy saving effect, as a result of the reduced internal volume as well as the enhance force capacity. To demonstrate this new concept, a sleeve muscle prototype was designed and fabricated. Experiments conducted on the prototype verified the improvement in the force capacity and demonstrated a significant energy saving effect (20%–37%). Finally, as the future work on this new concept, the paper presents a new robotic elbow design actuated with the proposed sleeve muscle. This unique design is expected to provide a highly compact and powerful actuation approach for robotic systems.     

Fabrication Process of Silicone-based Dielectric Elastomer Actuators

This contribution demonstrates the fabrication process of dielectric elastomer transducers (DETs). DETs are stretchable capacitors consisting of an elastomeric dielectric membrane sandwiched between two compliant electrodes. The large actuation strains of these transducers when used as actuators (over 300% area strain) and their soft and compliant nature has been exploited for a wide range of applications, including electrically tunable optics, haptic feedback devices, wave-energy harvesting, deformable cell-culture devices, compliant grippers, and propulsion of a bio-inspired fish-like airship. In most cases, DETs are made with a commercial proprietary acrylic elastomer and with hand-applied electrodes of carbon powder or carbon grease. This combination leads to non-reproducible and slow actuators exhibiting viscoelastic creep and a short lifetime. We present here a complete process flow for the reproducible fabrication of DETs based on thin elastomeric silicone films, including casting of thin silicone membranes, membrane release and prestretching, patterning of robust compliant electrodes, assembly and testing. The membranes are cast on flexible polyethylene terephthalate (PET) substrates coated with a water-soluble sacrificial layer for ease of release. The electrodes consist of carbon black particles dispersed into a silicone matrix and patterned using a stamping technique, which leads to precisely-defined compliant electrodes that present a high adhesion to the dielectric membrane on which they are applied.     

Better Endurance and Load Capacity: An Improved Design of Manta Ray Robot (RoMan-II)

An improved design of a biomimetic underwater vehicle (RoMan-II) inspired by manta ray is presented in this paper. The design of the prototype and the swimming motion control are discussed. Instead of using rigid multiple degree-of-freedom linkages as fin rays in the first version, six flexible fin rays are adopted to drive two sided fins which generate thrust through flapping motions. Furthermore, in order to save the energy for a long distance cruising, a bio-inspired gliding motion is incorporated onto the motion control of the improved prototype. With a closed-loop buoyancy control system, the vehicle can perform gliding locomotion in water, which reduces the overall energy consumption. The vehicle can also perform pivot turning and backward locomotion without turning its body. It can achieve an average velocity of one body length per second. The vehicle is able to carry various sensors or communication equipments, as the payload capacity is about 4 kg. Initial testing shows that the operation time of the buoyancy body is estimated to about 6 hours for free swimming and 90 hours for a pure gliding. The flapping frequency, flapping amplitude, and the number of waves performed across the fin's chord and wave directions can be independently tuned through the proposed control scheme. In general, the present prototype provides a useful platform to study the ray-like swimming motion in a single or combination mode of flapping, undulation and gliding.     

Permanent magnet actuation for magnetic bead-based DNA extraction

Background

Recently, automatic molecular diagnostic devices to extract DNA have been extensively developed using magnetic beads. While various methods can be applied to the control of the beads, the efficiency of the control when incorporated in automatic devices has not been studied. This paper proposes a compact magnet actuation method for the control of magnetic beads for DNA extraction, and compares the efficiency to the already available magnetic bead-based DNA extraction device. A permanent magnet was preferred for its compactness, while an electro-magnet provides easy operation. After investigating various methods to actuate the magnet with perspective to the size, circuit complexity, and power requirement, we determined the solenoid actuation method to be most efficient. To further reduce the dimension of the overall actuation device, direct actuation of the permanent magnet to control the hold/release of the beads was employed in this paper. The proposed method was compared with the conventional solenoid actuator with a metal plunger. An experimental fluidics device was set up with a fluidic channel and a syringe pump. The bead holding performance against the fluid speed was tested while a fixed amount of beads was loaded into the center of the channel. The group velocity of the beads was analyzed via image processing to determine whether the magnet was sufficient to hold the beads. The required power and space was analyzed and compared qualitatively and quantitatively.

Result

The proposed direct actuation method was capable of holding the beads at faster fluidic speed than the conventional solenoid actuator. The required power was comparable contemplating the high initial power of the solenoid actuator, and required much smaller space since no plunger was needed.

Conclusions

The direct actuation of the permanent magnet using a solenoid coil showed enhanced performance in holding the beads via permanent magnet, with less complexity of the actuation circuit and space. The proposed method therefore can efficiently improve the overall performance of the bead-based DNA extraction.

     

An Early Cambrian stem polychaete with pygidial cirri

The oldest annelid fossils are polychaetes from the Cambrian Period. They are representatives of the annelid stem group and thus vital in any discussion of how we polarize the evolution of the crown group. Here, we describe a fossil polychaete from the Early Cambrian Sirius Passet fauna, Pygocirrus butyricampum gen. et sp. nov., with structures identified as pygidial cirri, which are recorded for the first time from Cambrian annelids. The body is slender and has biramous parapodia with chaetae organized in laterally oriented bundles. The presence of pygidial cirri is one of the characters that hitherto has defined the annelid crown group, which diversified during the Cambrian-Ordovician transition. The newly described fossil shows that this character had already developed within the total group by the Early Cambrian.     

Bird terrestrial locomotion as revealed by 3D kinematics

Most birds use at least two modes of locomotion: flying and walking (terrestrial locomotion). Whereas the wings and tail are used for flying, the legs are mainly used for walking. The role of other body segments remains, however, poorly understood. In this study, we examine the kinematics of the head, the trunk, and the legs during terrestrial locomotion in the quail (Coturnix coturnix). Despite the trunk representing about 70% of the total body mass, its function in locomotion has received little scientific interest to date. This prompted us to focus on its role in terrestrial locomotion. We used high-speed video fluoroscopic recordings of quails walking at voluntary speeds on a trackway. Dorso-ventral and lateral views of the motion of the skeletal elements were recorded successively and reconstructed in three dimensions using a novel method based on the temporal synchronisation of both views. An analysis of the trajectories of the body parts and their coordination showed that the trunk plays an important role during walking. Moreover, two sub-systems participate in the gait kinematics: (i) the integrated 3D motion of the trunk and thighs allows for the adjustment of the path of the centre of mass; (ii) the motion of distal limbs transforms the alternating forward motion of the feet into a continuous forward motion at the knee and thus assures propulsion. Finally, head bobbing appears qualitatively synchronised to the movements of the trunk. An important role for the thigh muscles in generating the 3D motion of the trunk is suggested by an analysis of the pelvic anatomy.     

Mathematical Modeling of Pneumatic Artificial Muscle Actuation via Hydrogen Driving Metal Hydride-LaNi5

Quantitative understanding of mechanical actuation of intricate Pneumatic Artificial Muscle (PAM) actuators is technically required in control system design for effective real-time implementation.This paper presents mathematical modeling of the PAM driven by hydrogen-gas pressure due to absorption and desorption of metal hydride.Empirical models of both mechanical actuation of industrial PAM and chemical reaction of the metal hydride-LaNi5 are derived systematically where their interactions comply with the continuity principle and energy balance in describing actual dynamic behaviors of the PAM actuator (PAM and hydriding/dehydriding-reaction bed).Simulation studies of mechanical actuation under various loads are conducted so as to present dynamic responses of the PAM actuators.From the promising results,it is intriguing that the heat input for the PAM actuator can be supplied to,or pumped from the reaction bed,in such a way that absorption and desorption of hydrogen gas take place,respectively,in controlling the pressure of hydrogen gas within the PAM actuator.Accordingly,this manipulation results in desired mechanical actuation of the PAM actuator in practical uses.     

Current status of annelid phylogeny

Annelida is an ecologically and morphologically diverse phylum within the Lophotrochozoa whose members occupy a wide range of environments and show diverse life styles. The phylogeny of this group comprising more than 17,000 species remained controversial for a long time. By using next-generation sequencing and phylogenomic analyses of huge data matrices, it was finally possible to reach a well-supported and resolved annelid backbone tree. Most annelid diversity is comprised in two reciprocal monophyletic groups, Sedentaria and Errantia, which are named after the predominant life style of their members. Errantia include Aciculata (Phyllodocida?+?Eunicida) and Protodriliformia, which is a taxon of interstitial polychaetes. Sedentaria comprise most of the polychaete families formerly classified as Canalipalpata or Scolecida, as well as the Clitellata. Six taxa branch as a basal grade outside of this major radiation: Oweniidae, Magelonidae, Chaetopteridae, Sipuncula, Amphinomida, and Lobatocerebrum. Oweniidae and Magelonidae form a monophyletic group which we name Palaeoannelida, which constitutes the sister taxon of the remaining annelids. The early splits of annelid phylogeny date back to the Cambrian. The new annelid phylogeny highlights the variability and lability of annelid body plans, and many instances of simplifications of body plan as adaptations to new life styles can be found. Therefore, annelids will be an appropriate model to understand major transitions in the evolution of Bilateria in general. Evolutionary developmental studies are one way to investigate macroevolutionary transition in annelids. We briefly summarize the state of developmental model organisms in Annelida and also propose new candidates on the background of the phylogeny.     

Numerical analysis of a unique mode of locomotion: vertical climbing by Pacific lamprey

Pacific lampreys are capable of climbing vertical wetted surfaces through a two-phase (bending and stretching) locomotion mode using the oral disc for adherence. We investigate the physical mechanism and performance of this process by using a continuous beam model. Two mechanisms, one akin to the jumping process and the other related to the fast stretching of the body, have been identified. This locomotion mode may inspire biomimetic designs of anguilliform swimming devices capable of overcoming steep obstacles. By using a genetic algorithm simulation we identify the combination of kinematic parameters corresponding to optimal efficiency (defined as the gravitational potential energy gained in each climbing step divided by the energy spent to activate the motion). These parameters are similar to laboratory observations of lamprey motion, suggesting that this type of locomotion has been optimized for maximum efficiency through evolution.     

Pendular mechanics and the kinematics and energetics of brachiating locomotion

Because brachiating locomotion is characterized by a pattern of swinging movements, brachiation has often been analogized to pendular motion, and aspects of the mechanics of pendular systems have been used to provide insight into both energetic and structural design aspects of this locomotor mode. However, there are several limitations to this approach. First, the motions of brachiating animals only approximate pendular motion, and therefore the energetics of these two systems are only roughly comparable. Second, the kinematic similarity between brachiation and pendular motion will be maximal at only one velocity, and the correspondence will be even less at greater or lesser speeds. Third, all forms of terrestrial locomotion that involve the use of limbs incorporate elements of pendular systems, and therefore brachiation is not unusual in this respect. Finally, it has been suggested that the mechanics of pendular motion will constrain the maximum attainable body size of brachiating animals and that this mechanical situation explains the lack of brachiating primates of greater than 30-kg body size; the present analysis provides evidence that the constraints on body size are far less strict than previously indicated and that extrinsic factors such as the geometry of the forest environment are more likely to dictate maximum body size for brachiators.     

Bio-Inspired Wooden Actuators for Large Scale Applications

Implementing programmable actuation into materials and structures is a major topic in the field of smart materials. In particular the bilayer principle has been employed to develop actuators that respond to various kinds of stimuli. A multitude of small scale applications down to micrometer size have been developed, but up-scaling remains challenging due to either limitations in mechanical stiffness of the material or in the manufacturing processes. Here, we demonstrate the actuation of wooden bilayers in response to changes in relative humidity, making use of the high material stiffness and a good machinability to reach large scale actuation and application. Amplitude and response time of the actuation were measured and can be predicted and controlled by adapting the geometry and the constitution of the bilayers. Field tests in full weathering conditions revealed long-term stability of the actuation. The potential of the concept is shown by a first demonstrator. With the sensor and actuator intrinsically incorporated in the wooden bilayers, the daily change in relative humidity is exploited for an autonomous and solar powered movement of a tracker for solar modules.     

Compliance, actuation, and work characteristics of the goat foreleg and hindleg during level, uphill, and downhill running.

We model the action of muscle-tendon system(s) about a given joint as a serial actuator and spring. By this technique, the experimental joint moment is imposed while the combined angular deflection of the actuator and spring are constrained to match the experimental joint angle throughout the stance duration. The same technique is applied to the radial leg (i.e., shoulder/hip-to-foot). The spring constant that minimizes total actuator work is considered optimal, and this minimum work is expressed as a fraction of total joint/radial leg work, yielding an actuation ratio (AR; 1 = pure actuation and 0 = pure compliance). To address work modulation, we determined the specific net work (SNW), the absolute value of net divided by total work. This ratio is unity when only positive or negative work is done and zero when equal energy is absorbed and returned. Our proximodistal predictions of joint function are supported during level and 15 degrees grade running. The greatest AR and SNW are found in the proximal leg joints (elbow and knee). The ankle joint is the principal spring of the hindleg and shows no significant change in SNW with grade, reflecting the true compliance of the common calcaneal tendon. The principal foreleg spring is the metacarpophalangeal joint. The observed pattern of proximal actuation and distal compliance, as well as the substantial SNW at proximal joints, minimal SNW at intermediate joints, and variable energy absorption at distal joints, may emerge as general principles in quadruped limb mechanics and help to inform the leg designs of highly capable running robots.     

Design and Implementation of Cone Dielectric Elastomer Actuator with Double-Slider Mechanism

Dielectric Elastomer Actuators (DEA) have a wide application prospect in the area of robot due to its merits. The aim of this paper is to improve the displacement of cone DEA and to make full use of the large-strain advantage of elastomer, as well as to reduce the volume and mass of actuator. After presenting the manufacturing process and working principle of cone DEA, it is analyzed that negative stiffness preload can enlarge the displacement of actuator significantly. Then a half-diamond mechanism is analyzed using double-slider model to implement a negative stiffness preload. Two points from force-displacement curves, f_off and f_on of elastomer with voltage on and off, are selected as two working equilibrium positions of actuator to calculate the parameters of the preload mechanism, hereby the negative stiffness mechanism is realized. Displacement experiments show that the cone DEA has a displacement of 20 mm under voltage 7541V and experimental results agree well with analytical results. Since the initial displacement is very small, so the large-strain advantage of elastomer is used for improving the displacement of actuator. In addition, the force outputs of the actuator when voltage is on and off are acquired, which shows actuator has a maximal force ability of 1.6 N.