Protocorm culture of Dendrobium candidum in balloon type bubble bioreactors

Protocorm cultures of Dendrobium candidum were established in balloon type bubble bioreactors using Murashige and Skoog (MS) medium with 0.5 mg l⁻¹ α-naphthaleneacetic acid (NAA), 2.5% (w/v) sucrose, 5:25 mM NH₄:NO₃ and 1% (v/v) banana homogenate for the production of biomass and bioactive compounds. In 3 l bioreactor containing 2 l medium, a maximum protocorm biomass (21.0 g l⁻¹ dry biomass) and also optimum quantities of total polysaccharides (389.3 mg g⁻¹ DW), coumarins (18.0 mg g⁻¹ DW), polyphenolics (11.9 mg g⁻¹ DW), and flavonoids (4.5 mg g⁻¹ DW) were achieved after 7 weeks of culture. Based on these studies, 5 and 10 l bioreactor cultures were established to harvest 80 g and 160 g dry biomass. In 10 l bioreactors, the protocorms grown were accumulated with optimal levels of polysaccharides (424.1 mg g⁻¹ DW), coumarins (15.8 mg g⁻¹ DW), polyphenols (9.03 mg g⁻¹ DW) and flavonoids (4.7 mg g⁻¹ DW). The bioreactor technology developed here will be useful for the production of important bioactive compounds from D. candidum.     

Growth of the fungus Paecilomyces lilacinus with n-hexadecane in submerged and solid-state cultures and recovery of hydrophobin proteins

The filamentous fungus Paecilomyces lilacinus was grown on n-hexadecane in submerged (SmC) and solid-state (SSC) cultures. The maximum CO₂ production rate in SmC (V_max = 11.7 mg CO₂ L_g⁻¹ day⁻¹) was three times lower than in SSC (V_max = 40.4 mg CO₂ L_g⁻¹ day⁻¹). The P. lilacinus hydrophobin (PLHYD) yield from the SSC was 1.3 mg PLHYD g protein⁻¹, but in SmC, this protein was not detected. The PLHYD showed a critical micelle concentration of 0.45 mg mL⁻¹. In addition, the PLHYD modified the hydrophobicity of Teflon from 130.1 ± 2° to 47 ± 2°, forming porous structures with some filaments <1 μm and globular aggregates <0.25 μm diameter. The interfacial studies of this PLHYD could be the basis for the use of the protein to modify surfaces and to stabilize compounds in emulsions.     

Volatile fatty acids accumulation and rhamnolipid generation in situ from waste activated sludge fermentation stimulated by external rhamnolipid addition

The solubilization and acidification of waste activated sludge (WAS) were apparently enhanced by external rhamnolipid (RL) addition. The maximum solute carbohydrate concentrations increased linearly from 48 ± 5 mg COD L⁻¹ in the un-pretreated WAS (blank) to 566 ± 19 mg COD L⁻¹, and protein increased from 1050 ± 8 to 3493 ± 16 mg COD L⁻¹ at RL dosage of 0.10 g g⁻¹ TSS. The highest VFAs concentration peaked at 3840 mg COD L⁻¹ at RL dosage of 0.04 g g⁻¹ TSS, which was 4.24-fold higher than the blank test. RL was generated in situ during WAS fermentation when external RL was added. It was detected that RL concentration was increased from initial 880 ± 92 mg L⁻¹ to 1312 ± 7 mg L⁻¹ at the end of 96 h with RL dosage of 0.04 g g⁻¹ TSS, which was increased to 1.49-fold. Meanwhile, methane production was notably reduced to a quite low level of 2.0 mL CH₄ g⁻¹ VSS, showing effective inhibition of methanogens by RL (58.8 mL CH₄ g⁻¹ VSS in the blank). In addition, the activity of hydrolytic enzymes (protease and α-glucosidase) was enhanced accordingly. VFAs accumulation and RL generation in situ demonstrated that the additional RL substantially performed enhanced biological effects for waste activated sludge fermentation.     

A pilot study of synbiotic supplementation on breast milk mineral concentrations and growth of exclusively breast fed infants

Despite the crucial role of breast milk mineral contents for health and growth of the infants, they decrease with the duration of lactation. So, this pilot study aimed to determine the effects of synbiotic supplementation on breast milk mineral composition and infants’ growth. In this pilot, randomized, double-blind, placebo-controlled trial, 57 lactating mothers were randomly divided into two groups to receive a daily supplement of synbiotic (n = 30) or a placebo (n = 27) for 30 days. Breast milk zinc, copper, Iron, magnesium and, calcium concentrations were determined by flame atomic absorption spectrometry. Weight for age Z-score (WAZ) and height for age Z-score (HAZ) were assessed for infants. Dietary intake was collected from lactating women using the 24-h recall method. Data analyses were carried out using nutritionist IV, Epi Info and SPSS soft wares. Synbiotic supplementation led to an insignificant increase of the mean breast milk levels of zinc (from 2.44 ± 0.65 to 2.55 ± 0.55 mg L⁻¹), copper (from 0.35 ± 0.24 to 0.40 ± 0.26 mg L⁻¹), iron (from 0.28 ± 0.42 to 0.31 ± 0.38 mg L⁻¹), magnesium (from 17.14 ± 1.35 to 17.17 ± 1.09 mg L⁻¹), and calcium (from 189 ± 25.3 to 189.9 ± 21.7 mg L⁻¹); whilst in the placebo group, these variables decreased significantly (P = 0.001). The observed changes between two groups were statistically significant (P < 0.05). Although WAZ and HAZ of infants increased slightly in the supplemented group (from 1.19 ± 0.79 to 1.20 ± 0.69 and 0.36 ± 0.86 to 0.37 ± 0.85 respectively), these two parameters decreased in the placebo group which was significant only for WAZ (P = 0.01). Moreover, no significant association was found between mineral intake and breast milk mineral contents. It seems, synbiotic supplementation may have positive effects on breast milk mineral contents.     

Preventive effect of rikkunshito on gastric motor function inhibited by l-dopa in rats

We previously reported that ghrelin prevented l-dopa (LD)-induced inhibition of gastric emptying (GE) of a non-nutrient solution in rats. Parkinson's disease treatment involves the combined administration of l-dopa with the enzyme l-amino acid decarboxylase inhibitor, carbidopa (CD) to reduce peripheral formation of dopamine. We investigated the effect LD/CD given orogastrically (og) on GE of a non-nutrient or nutrient meal and whether og pretreatment with rikkunshito, a kampo medicine clinically used to treat gastroparesis, influenced LD/CD effect on GE and postprandial antral and duodenal motility in conscious rats. LD/CD (20/2 mg kg⁻¹) decreased significantly GE to 26.3 ± 6.0% compared to 61.2 ± 3.2% in og vehicle monitored 20-min after a non-nutrient meal and to 41.9 ± 5.8% compared to 72.9 ± 5.2% in og vehicle monitored 60 min after a nutrient meal. Rikkunshito (0.5 or 1.0 g kg⁻¹) reduced the LD/CD (20/2 mg kg⁻¹) inhibition of GE of non-nutrient meal (36.9 ± 7.4% and 46.6 ± 4.8% respectively vs. 12.1 ± 7.4% in og vehicle plus LD/CD) while having no effect alone (56.6 ± 8.5%). The ghrelin antagonist, [d-Lys³]-GHRP-6 (1 mg kg⁻¹) injected intraperitoneally partially reversed rikkunshito preventive effect on LD/CD-inhibited GE. Rikkunshito (1.0 g kg⁻¹) blocked LD/CD (20/2 mg kg⁻¹)-induced delayed GE of a nutrient meal and the reduction of postprandial antral motility. In 6-hydroxydopamine-induced Parkinson's disease rat model, rikkunshito (1.0 g kg⁻¹, og) also prevented LD/CD-inhibited gastric emptying of a nutrient meal and enhanced fasting plasma levels of acylated ghrelin. These data indicate that oral rikkunshito alleviates the delayed GE induced by LD/CD in naïve and PD rat model in part through ghrelin-related mechanisms.     

Influence on dithiolopyrrolone antibiotic production by organic acids in Saccharothrix algeriensis NRRL B-24137

The influence of organic acids on growth and dithiolopyrrolone antibiotic production by Saccharothrix algeriensis NRRL B-24137 was studied. The production of dithiolopyrrolones depends upon the nature and concentration of the organic acids in the culture medium. Study of the nature of organic acids showed that the most effective organic acids for thiolutin specific production were maleic, 4-hydroxybenzoic, benzentetracarboxylic, pantothenic, pivalic and pyruvic acids (which yielded almost five-fold over the starting medium) and pimelic acid (more than three-fold). 4-Bromobenzoic acid showed the best production of senecioyl-pyrrothine (59 mg g⁻¹ DCW). Tiglic acid showed the best production of tigloyl-pyrrothine (22 mg g⁻¹ DCW). The highest yield of isobutyryl-pyrrothine (7.6 mg g⁻¹ DCW) was observed in the presence of crotonic acid. Sorbic acid yielded the best production of butanoyl-pyrrothine (26 mg g⁻¹ DCW). Methacrylic, butyric, pyruvic and 4-bromobenzoic acids also exhibited the best production of butanoyl-pyrrothine (27–11-fold).Study of organic acid concentration showed that among the selected organic acids, pimelic acid yielded the highest specific production of thiolutin (91 mg g⁻¹ DCW) at 7.5 mM; and senecioyl-pyrrothine (11 mg g⁻¹ DCW), tigloyl-pyrrothine (9 mg g⁻¹ DCW) and butanoyl-pyrrothine (3.5 mg g⁻¹ DCW) at 5 mM. Pyruvic acid at 1.25 mM enhanced the production of senecioyl-pyrrothine (4.3 mg g⁻¹ DCW). The maximum production of tigloyl-pyrrothine (18.6 mg g⁻¹ DCW) was observed in the presence of tiglic acid at 2.5 mM. Maximum production of isobutyryl-pyrrothine was observed in the presence of 7.5 mM tiglic acid. In addition, methacrylic acid (at 5 mM) and butyric acid (at 2.5 mM) enhanced the production of butanoyl-pyrrothine (26 and 20 times, respectively).The above results can be employed in the optimisation of the culture medium for the production of dithiolopyrrolone in higher quantities.     

A high pressure liquid chromatography-based assay for glutathione-S-transferase class distinction assay

In order to expedite the process of classification of the members of the family of glutathione-S-transferases (GSTs) high performance liquid chromatography with photodiode array detection (HPLC-PDA) was used as a means for measuring enzymatic activity. The GST chosen for the development of the HPLC-PDA technique was from equine liver (E-GST). The characterizing substrates, ethacrynic acid (EA) and bromosulfophthalein (BSP), along with previously gathered characterization data allowed for the distinction of α, μ or π-class enzymes. In an initial characterization of the previously unclassified E-GST it was determined that the enzyme was of the π-class with specific activities of 0.062, ± 0.0015 μmol min^− 1 mg^− 1 and 0.0019, ± 0.00064 μmol min^− 1 mg^− 1 for EA and BSP, respectively. Finally, the activity of the E-GST with the EA and BSP substrates, was measured by HPLC-PDA, and was found to be 0.027, ± 0.003 μmol min^− 1 mg^− 1 and 0.002, ± 0.0005 μmol min^− 1 mg^− 1, respectively. While the HPLC-PDA data do not mirror the spectrophotometric results quantitatively the overall response by the E-GST was the same. In general, the E-GSTs were shown to belong to the π-class when characterized by HPLC-PDA due to an EA specific activity greater than 0.01 μmol min^− 1 mg^− 1 and a negligible BSP activity (≤ 0.002 μmol min^− 1 mg^− 1).     

Stress responses and specific metal exclusion on mine soils based on germination and growth studies by Australian golden wattle

We reported the Australian golden wattle as a copper stabilizer in abandoned copper mine soils earlier. Here we investigate to confirm this plant’s suitability to grow on metal contaminated mine soils based on stress indication. The seeds of Acacia pycnantha collected from mining area were germinated after heat and no heat treatment on two types of irrigation. The daily irrigated and heat treated seeds gave up to 85% germination on sandy soil. The A. pycnantha was grown under greenhouse condition in six different soils collected from abandoned copper mine at Kapunda in South Australia. Among the six soil samples, soil-1 with the highest copper concentration produced 2.05 mmol g⁻¹ tissue of proline. Proline expression was prominent in more saline soils (1, 5 and 6) having electrical conductivity (EC) 1184, 1364 and 1256 μS, respectively. Chlorophyll a, b and carotenoid levels in plants showed a gradually decreasing trend in all the soils as experiment progressed. The plants grown on soil sample-1, containing 4083 ± 103 mg kg⁻¹ of copper resulted in 18 ± 2 mg kg⁻¹ accumulation in its leaf. The calcium accumulation was significant up to 11648 ± 1209 mg kg⁻¹ in leaf. Although pore water samples showed higher Cu concentration in soils, an increased mobility of arsenic and lead was observed in all the soil samples. Our experiment points out the need for proper monitoring of revegetation processes to avoid revegetation and reclamation failure.     

Nitrite inhibition and intermediates effects on Anammox bacteria: A batch-scale experimental study

A batch test procedure, based on manometric measurements, was used to study the Anammox process, in particular the inhibition due to nitrite and the effects of hydroxylamine and hydrazine, indicated as possible intermediates of the process. The maximum nitrite removal rate (MNRR) was measured. The method showed good reliability with a standard error of 4.5 ± 3.3% (n: 41). All the tests were carried out on samples taken from a pilot plant with Anammox suspended biomass. The tests were used also to monitor the reactor activity. By testing different spiked additions of nitrite (10–75 mg NO₂⁻-N L⁻¹), a short-term inhibition, with more than 25% MNRR decrease, was found at concentrations higher than 60 mg NO₂⁻-N L⁻¹. Repeated additions of nitrite higher than 30 mg NO₂⁻-N L⁻¹ caused losses of activity. After a complete loss of activity, spiked additions of hydroxylamine (30 mg N L⁻¹ in total) determined a 20% permanent recovery. Low amounts of the intermediates (1–3 mg N L⁻¹) applied on partially inhibited samples and uninhibited samples produced temporary increases in activity up to 50% and 30%, respectively.     

Sulfate reduction and microbial community of autotrophic biocathode in response to acidity

Microbial electrolysis cells (MECs) with autotrophic biocathode are a promising technology for removal of pollutants in wastewater. The aim of this study was to investigate the effect of initial acidity of wastewater on performance of sulfate-reducing biocathodes. MECs with biocathodes were operated with initial pH values of catholyte ranged from 3.0 to 7.0. The optimum initial pH value was 6.0 with a maximum sulfate reductive rate and biomass of 57 mg L⁻¹ d⁻¹ and 2.1 ± 0.4 mg g⁻¹, respectively. With initial pH 7.0, the pH value of catholyte increased to 9.8 ± 0.2 after an operation cycle, which resulted in low performance of the biocathode. A considerable sulfate reductive rate of 31 ± 0.85 mg L⁻¹ d⁻¹ was achieved with initial pH 3.0. Desulfovibrio sp. grew dominantly with abundance of 46%–66% in the cathode biofilm with initial pH values from 3.0 to 6.0 and contributed to the sulfate reduction. Clostridium and Parapedobacter also had high abundance in pH 6.0 cathode, indicated that interspecies electron transfer between electrochemical active and sulfate-reducing bacteria could play an important role in sulfate removal. The results suggest that acidity of catholyte is an important factor to be considered to utilize autotrophic biocathode MECs for wastewater treatment.     

Investigation on the formation and kinetics of glucose-fed aerobic granular sludge

Aerobic granular sludge was cultivated in a glass sequencing batch reactor (SBR) with glucose synthetic wastewater. The spherical shaped granules were observed on 4th day with the mean diameter of 0.1 mm. With the increase of chemical oxygen demand (COD) concentration of the influent, aerobic granules grew matured, the size of which ranged from 1.2 to 1.9 mm. The aerobic granular sludge could sustain high organic loading rate (about 4.0 g COD L⁻¹ d⁻¹), with good settling ability (settling velocity 36 m/h) and high biomass concentration (MLSS 6.7 ±0.2 g/L). Experimental data indicated that the substrate utilization and biomass growth kinetics followed Monod's kinetics model approximately. The corresponding kinetic coefficients of maximum specific substrate utilization rate (k), half velocity coefficient (K_s), growth yield coefficient (Y) and decay coefficient (K_d) were 13.2 d⁻¹, 275.8 mg/L, 0.183–0.250 mg MLSS/mg COD and 0.023–0.075 d⁻¹, respectively, which made aerobic granules have short setup period, high rate of substrate utilization and little surplus sludge.     

Determination of selenium and its compounds in marine organisms

In this study, we investigate the type and quantity of selenium compounds in fish and marine organisms, using ion-pair reversed phase LC–ICP-MS, developed and applied for the analysis of Atlantic cod, Atlantic salmon, Greenland halibut, Atlantic herring, blue mussel, common crab, scallop, calanus, and Euphasia super. Of the samples examined, the lowest level of selenium was found in farmed Atlantic salmon (0.17 mg Se kg⁻¹ dm). The total selenium extraction efficiency by phosphate buffer was 2.5 times higher in sea plankton and shellfish samples than in fish samples. Analysis of Se species in each hydrolysate obtained by proteolysis showed the presence of selenomethionine, which constituted 41.5% of the selenium compounds detected in hydrolysates of Atlantic herring and 98.4% of those in extracts of Atlantic salmon. Inorganic compounds, such as selenates and selenites, were detected mainly in sea plankton and shellfish samples (<0.13 mg Se kg⁻¹ wm), although no correlation was found between the presence of inorganic compounds and total selenium concentration. The accuracy of the total selenium determination was validated using a certified reference material (oyster tissue (NIST 1566b)). A lyophilised powder of cod (Gadus morhua) was used to validate speciation analysis, enzymatic hydrolysis of lyophilised powder of cod recovered 54 ± 6% of total selenium, and SeMet constituted 83.5 ± 5.28% of selenium detected in hydrolysates. The chromatographic detection limits were, respectively, 0.30 ng mL⁻¹, 0.43 ng mL⁻¹, 0.54 ng mL⁻¹, 0.55 ng mL⁻¹, 0.57 ng mL⁻¹ and 0.72 ng mL⁻¹ for selenate, selenomethionine, selenite, Se-methyl-selenocysteine, selenocystine and selenomethionine selenoxide.The data on selenium concentrations and speciation presented here could be useful in estimating levels of selenium intake by seafood consumption.     

Treatment of dye-rich wastewater by an immobilized thermophilic cyanobacterial strain: Phormidium sp.

The removal of Remazol Blue and Reactive Black B by the immobilized thermophilic cyanobacterial strain Phormidium sp. was investigated under thermophilic conditions in a batch system, in order to determine the optimal conditions required for the highest dye removal. In the experiments, performed at pH 8.5, with different initial dye concentrations between 9.1 mg l⁻¹ and 82.1 mg l⁻¹ and at 45 °C, calcium alginate immobilized Phormidium sp. showed high dye decolorization, with maximum uptake yields ranging from 50% to 88% at all dye concentrations tested. When the effects of high dye concentrations on dye removal were investigated, the highest uptake yield in the beads was 50.3% for 82.1 mg l⁻¹ Remazol Blue and 60.0% for 79.5 mg l⁻¹ Reactive Black B. The highest color removal was detected at 45 °C and 50 °C incubation temperatures for all dye concentrations. As the temperature decreased, the removal yield of immobilized Phormidium sp. also decreased. At about 75 mg l⁻¹ initial dye concentrations, the highest specific dye uptake measured was 41.29–41.17 mg g⁻¹ for Remazol Blue and 47.69–43.82 mg g⁻¹ for Reactive Black B at 45 °C and 50 °C incubation temperatures, respectively, after 8 days incubation.     

Repeatability of a running heat tolerance test

At present there is no standardised heat tolerance test (HTT) procedure adopting a running mode of exercise. Current HTTs may misdiagnose a runner's susceptibility to a hyperthermic state due to differences in exercise intensity. The current study aimed to establish the repeatability of a practical running test to evaluate individual's ability to tolerate exercise heat stress. Sixteen (8M, 8F) participants performed the running HTT (RHTT) (30 min, 9 km h⁻¹, 2% elevation) on two separate occasions in a hot environment (40 °C and 40% relative humidity). There were no differences in peak rectal temperature (RHTT1: 38.82±0.47 °C, RHTT2: 38.86±0.49 °C, Intra-class correlation coefficient (ICC)=0.93, typical error of measure (TEM)=0.13 °C), peak skin temperature (RHTT1: 38.12±0.45, RHTT2: 38.11±0.45 °C, ICC=0.79, TEM=0.30 °C), peak heart rate (RHTT1: 182±15 beats min⁻¹, RHTT2: 183±15 beats min⁻¹, ICC=0.99, TEM=2 beats min⁻¹), nor sweat rate (1721±675 g h⁻¹, 1716±745 g h⁻¹, ICC=0.95, TEM=162 g h⁻¹) between RHTT1 and RHTT2 (p>0.05). Results demonstrate good agreement, strong correlations and small differences between repeated trials, and the TEM values suggest low within-participant variability. The RHTT was effective in differentiating between individuals physiological responses; supporting a heat tolerance continuum. The findings suggest the RHTT is a repeatable measure of physiological strain in the heat and may be used to assess the effectiveness of acute and chronic heat alleviating procedures.     

Galactose-limited fed-batch cultivation of Escherichia coli for the production of lacto-N-tetraose

Lacto-N-tetraose (Gal(β1-3)GlcNAc(β1-3)Gal(β1-4)Glc) is one of the most abundant oligosaccharide structures in human milk. We recently described the synthesis of lacto-N-tetraose by a whole-cell biotransformation with recombinant Escherichia coli cells. However, only about 5% of the lactose was converted into lacto-N-tetraose by this approach. The major product obtained was the intermediate lacto-N-triose II (GlcNAc(β1-3)Gal(β1-4)Glc).In order to improve the bioconversion of lactose to lacto-N-tetraose, we have investigated the influence of the carbon source on the formation of lacto-N-tetraose and on the intracellular availability of the glycosyltransferase substrates, UDP-N-acetylglucosamine and UDP-galactose. By growth of the recombinant E. coli cells on D-galactose, the yield of lacto-N-tetraose (810.8 mg L⁻¹ culture) was 3.6-times higher compared to cultivation on D-glucose.Using fed-batch cultivation with galactose as sole energy and carbon source, a large-scale synthesis of lacto-N-tetraose was demonstrated. During the 26 h feeding phase the growth rate (μ = 0.05) was maintained by an exponential galactose feed. In total, 16 g L⁻¹ lactose were fed and resulted in final yields of 12.72 ± 0.21 g L⁻¹ lacto-N-tetraose and 13.70 ± 0.10 g L⁻¹ lacto-N-triose II. In total, 173 g of lacto-N-tetraose were produced with a space-time yield of 0.37 g L⁻¹ h⁻¹.     

Multiple regeneration pathways in Spathoglottis plicata Blume — A study in vitro

Asymbiotic germination of immature seeds (embryos), and mature seeds and micropropagation of Spathoglottis plicata were described. Effects of three nutrition media namely, Murashige & Skoog (MS); Phytamax (PM); and Phyto-Technology orchid seed sowing medium (P₇₂₃), two carbon sources such as glucose and sucrose at 2–3% (w/v), two plant growth regulators such as 6-benzylaminopurine (BAP; 0.5–3.0 mg l^− 1) and α-naphthalene acetic acid (NAA; 0.5–2.0 mg l^− 1) and peptone (2.0 g l^− 1) were examined on seed germination, early protocorm development and micropropagation. The maximum germination of mature seeds (95%) was recorded in PM medium supplemented with 2% (w/v) sucrose + 2.0 g l^− 1 peptone. For germination of embryos P₇₂₃ medium supplemented with 1.0 mg l^− 1 BAP proved best. Multiple shoot buds or protocorm-like bodies (PLBs) were produced from stem segments of in vitro raised seedlings. Both direct organogenesis and embryogenesis were observed and the morphogenetic response was initiated by different concentrations and combinations of PGRs. The optimum PGR combination for maximal PLB regeneration was 1.0 mg l^− 1 NAA + 2.5 mg l^− 1 BAP, while 1.0 mg l^− 1 NAA + 1.0 mg l^− 1 BAP for shoot bud development. Strong and stout root system was induced in half strength PM medium supplemented with 0.5 mg l^− 1 IAA. The well-rooted plantlets were transferred to pots containing a potting mixture composed of saw dust, coconut coir, humus, and coal pieces at 1:1:1:2 (w/w) with 80% survival in outside environment and flowered after two years of transfer.     

Peel of araticum fruit (Annona crassiflora Mart.) as a source of antioxidant compounds with α-amylase, α-glucosidase and glycation inhibitory activities

Annona crassiflora Mart., whose fruit is popularly known as araticum, is a member of the Annonaceae family found in the Brazilian Cerrado. Although this plant has several medicinal uses, its bioactive molecules are not fully understood. A bioguided assay was performed to identify the main bioactive compounds of A. crassiflora fruit peel from the ethanol extract fractions with antioxidant capacity and α-amylase, α-glucosidase and glycation inhibitory activities. Ethyl acetate and n-butanol fractions showed, respectively, higher antioxidant capacity (DPPH IC₅₀ 1.5 ± 0.1 and 0.8 ± 0.1 μg mL⁻¹, ORAC 3355 ± 164 and 2714 ± 79 μmol trolox eq/g, and FRAP 888 ± 16 and 921 ± 9 μmol trolox eq/g) and inhibitory activities against α-amylase (IC₅₀ 4.5 ± 0.8 and 1.7 ± 0.3 μg mL⁻¹), α-glucosidase (IC₅₀ 554.5 ± 158.6 and 787.8 ± 140.6 μg mL⁻¹) and glycation (IC₅₀ 14.3 ± 3.3 and 16.0 ± 4.2 μg mL⁻¹), and lower cytotoxicity, compared to the other fractions and crude ethanol extract. The HPLC-ESI-MS/MS analysis identified various biomolecules known as potent antioxidants, such as chlorogenic acid, (epi)catechin, procyanidins, caffeoyl-hexosides, quercetin-glucosides and kaempferol. The fruit peel of A. crassiflora, a specie from Cerrado, the Brazilian Savanna, provided a source of antioxidant compounds with properties to block carbohydrate digestive enzymes and formation of glycation products. Thus, there is potential to use the by-products of araticum in order to identify and isolate phytochemicals for application in nutraceutical supplements, food additives and pharmaceuticals products.     

Immobilized glucose oxidase on different supports for biotransformation removal of glucose from oligosaccharide mixtures

Four immobilized forms of glucose oxidase (GOD) were used for biotransformation removal of glucose from its mixture with dextran oligosaccharides. GOD was biospecifically bound to Concanavalin A-bead cellulose (GOD-ConA-TBC) and covalently to triazine-bead cellulose (GOD-TBC). Eupergit C and Eupergit CM were used for preparation of other two forms of immobilized GOD: GOD-EupC and GOD-EupCM. GOD-ConA-TBC and GOD-EupC exhibited the best operational and storage stabilities. pH and temperature optima of these two immobilized enzyme forms were broadened and shifted to higher values (pH 7 and 35 °C) in comparison with those of free GOD. The decrease of V_max values after immobilization was observed, from 256.8 ± 7.0 μmol min⁻¹ mg_GOD⁻¹ for free enzyme to 63.8 ± 4.2 μmol min⁻¹ mg_GOD⁻¹ for GOD-ConA-TBC and 45 ± 2.7 μmol min⁻¹ mg_GOD⁻¹ for GOD-EupC, respectively. Depending on the immobilization mode, the immobilized GODs were able to decrease the glucose content in solution to 3.8–15.6% of its initial amount The best glucose conversion, was achieved by an action of GOD-EupCM on a mixture of 100 g dextran with 9 g of glucose (i.e. 98.7% removal of glucose).     

Oxygen enhances the recovery of Potamogeton maackianus from prolonged exposure to very low irradiance

Recovery ability in relation to carbohydrate content of Potamogeton maackianus growing in two dissolved oxygen concentrations (8 and 2 mg L⁻¹) was investigated during 28 days exposure to very low irradiance (about 0.06 μmol m⁻² s⁻¹). Plant weight remained relatively constant (0.19 g dry wt plant⁻¹) within the initial 21 days in the high oxygen treatment, but decreased to 0.14 g dry wt plant⁻¹ at the end of the experiment. In low oxygen environments, plant weight was similar within the initial 14 days, but decreased to 0.08 g dry wt plant⁻¹ at 21 day. During the experimental period, both soluble sugar and starch contents in shoots decreased with time. Compared to high oxygen treatment, plants in the low oxygen treatment depleted starch more quickly (25 versus 18 mg g⁻¹ at 28 day) but remained a relatively high soluble sugar content (0.9 versus 1.8 mg g⁻¹ at 28 day). After recovery in high light and high dissolved oxygen conditions for 1 week, plant growth rate, new branch number, stem elongation rate and leaf recruitment number were significantly higher in high oxygen than in the low oxygen treatments. These data suggest that the ability of the plant to recover from prolonged exposure to very low irradiance is related to the depletion level of carbohydrate stored in plant tissues, which is regulated by oxygen availability in the water.     

Repeated fed-batch cultivation of Arthrospira (Spirulina) platensis using urea as nitrogen source

Arthrospira (Spirulina) platensis (Nordstedt) Gomont was autotrophically cultivated for biomass production in repeated fed-batch process using urea as nitrogen source, with the aim of making large-scale production easier, increasing cell productivity and then reducing the production costs. It was investigated the influence of the ratio of renewed volume to total volume (R), the urea feeding time (t_f) and the number of successive repeated fed-batch cycles on the maximum cell concentration (X_m), cell productivity (P_x), nitrogen-to-cell conversion yield (Y_x/n), maximum specific growth rate (μ_m) and protein content of dry biomass. The experimental results demonstrated that R = 0.80 and t_f = 6 d were the best cultivation conditions, being able to simultaneously ensure, throughout the three fed-batch cycles, the highest average values of three of the five responses (X_m = 2101 ± 113 mg L^?1, P_x = 219 ± 13 mg L^?1 d^?1 and Y_x/n = 10.3 ± 0.8 g g^?1).