Microbial degradation of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in soils

[This corrects the article on p. 3236 in vol. 59.].     

Viscoelastic relaxations and thermal properties of bacterial poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and poly(3-hydroxybutyrate-co-4-hydroxybutyrate)

3-Hydroxybutyrate-3-hydroxyvalerate (3HB-3HV) as well as 3-hydroxybutyrate-4-hydroxybutyrate (3HB-4HB) copolyesters have been investigated by differential scanning calorimetry, thermogravimetric analysis and dynamic mechanical spectroscopy, over a wide range of compositions (0-95 mol% 3HV; 0-82 mol% 4HB). Both series of isolated copolyesters are partially crystalline at all compositions. Quenched samples show a glass transition that decreases linearly with increasing co-monomer molar fraction, more markedly when the co-monomer is 4HB. Above Tg, all copolyesters, rich in 3HB units, show a cold crystallization phenomenon followed by melting, while at the other end crystallization on heating is observed only in 3HB-3HV copolymers. The viscoelastic spectrum, strongly affected by thermal history, shows two relaxation regions: the glass transition, whose location depends on copolymer type and composition, and a secondary dispersion region at low temperatures (-130/-80 degrees C). The latter results from a water-related relaxation analogous to that of P(3HB) and, in 3HB-4HB copolymers, from another overlapping absorption peak centered at -130 degrees C, attributed to local motion of the methylene groups in the linear 4HB units.     

In vitro biocompatibility of electrospun poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) fiber mats

In the present contribution, the potential for use of the ultrafine electrospun fiber mats of poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) as scaffolding materials for skin and nerve regeneration was evaluated in vitro using mouse fibroblasts (L929) and Schwann cells (RT4-D6P2T) as reference cell lines. Comparison was made with PHB and PHBV films that were prepared by solution-casting technique. Indirect cytotoxicity assessment of the as-spun PHB and PHBV fiber mats with mouse fibroblasts (L929) and Schwann cells (RT4-D6P2T) indicated that the materials were acceptable to both types of cells. The attachment of L929 on all of the fibrous scaffolds was significantly better than that on both the film scaffolds and tissue-culture polystyrene plate (TCPS), while RT4-D6P2T appeared to attach on the flat surfaces of TCPS and the film scaffolds much better than on the rough surfaces of the fibrous scaffolds. For L929, all of the fibrous scaffolds were superior in supporting the cell proliferation to the film counterparts, but inferior to TCPS at days 3 and 5, while, for RT4-D6P2T, the rough surfaces of the fibrous scaffolds appeared to be very poor in supporting the cell proliferation when comparing with the smooth surfaces of TCPS and the film scaffolds. Scanning electron microscopy was also used to observe the behavior of both types of cells that were cultured on both the fibrous and the film scaffolds and glass substrate for 24 h.     

Anaerobic degradation of poly-3-hydroxybutyrate and poly-3-hydroxybutyrate-co-3-hydroxyvalerate

The anaerobic degradation of the polyesters poly-3-hydroxybutyrate (PHB) and poly-3-hydroxybutyrate-co-3-hydroxyvalerate (PHBV) was investigated with special regard to intermediate products, kinetics, and yields. During the degradation of PHBV acetate, propionate, n-butyrate, and n-valerate were detected. Additionally, 3-hydroxybutyrate and 3-hydroxyvalerate and four dimeric esters of these two molecules were identified by GC-MS measurements. Three different test systems for the anaerobic degradation of polyesters were studied. It was not possible to get reproducible results by means of the Anaerobic Sturm-test, a simple system based on carbon dioxide measurement. Secondly, a system based on the GC measurement of accumulated organic acids was investigated. A degradation of 90% in two days was calculated by a carbon balance. Best results were reached with the third test system based on the measurement of methane with a gas meter. A degradation of 99% was observed within 30 days.     

Anaerobic degradation of poly-3-hydroxybutyrate and poly-3-hydroxybutyrate-co-3-hydroxyvalerate

The anaerobic degradation of the polyesterspoly-3-hydroxybutyrate (PHB) andpoly-3-hydroxybutyrate-co-3-hydroxyvalerate (PHBV) wasinvestigated with special regard to intermediateproducts, kinetics, and yields. During the degradationof PHBV acetate, propionate, n-butyrate, andn-valerate were detected. Additionally,3-hydroxybutyrate and 3-hydroxyvalerate and fourdimeric esters of these two molecules were identifiedby GC-MS measurements. Three different test systemsfor the anaerobic degradation of polyesters werestudied. It was not possible to get reproducibleresults by means of the Anaerobic Sturm-test, a simplesystem based on carbon dioxide measurement. Secondly,a system based on the GC measurement of accumulatedorganic acids was investigated. A degradation of 90%in two days was calculated by a carbon balance. Bestresults were reached with the third test system basedon the measurement of methane with a gas meter. Adegradation of 99% was observed within 30 days.     

Degradation of poly (3-hydroxybutyrate) and its copolymer poly (3-hydroxybutyrate-co-3-hydroxyvalerate) by a marine Streptomyces sp. SNG9.

A marine Streptomyces sp. SNG9 was characterized by its ability to utilize poly(3-hydroxybutyrate) (PHB) and its copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate P (3HB-co-HV). The bacterium grew efficiently in a simple mineral liquid medium enriched with 0.1% poly(3-hydroxybutyrate) powder as the sole carbon source. Cells excreted PHB depolymerase and degraded the polymer particles to complete clarity in 4 days. The degradation activity was detectable by the formation of a clear zone around the colony (petri plates) or a clear depth under the colony (test tubes). The expression of PHB depolymerase was repressed by the presence of simple soluble carbon sources. Bacterial degradation of the naturally occurring sheets of poly(3-hydroxybutyrate) and its copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) was observed by scanning electron microscopy (SEM). Morphological alterations of the polymers sheets were evidence for bacterial hydrolysis.     

Degradation of poly (3-hydroxybutyrate) and its copolymer poly (3-hydroxybutyrate-co-3-hydroxyvalerate) by a marine Streptomyces sp. SNG9

A marine Streptomyces sp. SNG9 was characterized by its ability to utilize poly(3-hydroxybutyrate) (PHB) and its copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate P (3HB-co-HV). The bacterium grew efficiently in a simple mineral liquid medium enriched with 0.1% poly(3-hydroxybutyrate) powder as the sole carbon source. Cells excreted PHB depolymerase and degraded the polymer particles to complete clarity in 4 days. The degradation activity was detectable by the formation of a clear zone around the colony (petri plates) or a clear depth under the colony (test tubes). The expression of PHB depolymerase was repressed by the presence of simple soluble carbon sources. Bacterial degradation of the naturally occurring sheets of poly(3-hydroxybutyrate) and its copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) was observed by scanning electron microscopy (SEM). Morphological alterations of the polymers sheets were evidence for bacterial hydrolysis.     

Microbial production of 4-hydroxybutyrate,poly-4-hydroxybutyrate,and poly(3-hydroxybutyrate-co-4-hydroxybutyrate) by recombinant microorganisms

4-Hydroxybutyrate (4HB) was produced by Aeromonas hydrophila 4AK4, Escherichia coli S17-1, or Pseudomonas putida KT2442 harboring 1,3-propanediol dehydrogenase gene dhaT and aldehyde dehydrogenase gene aldD from P. putida KT2442 which are capable of transforming 1,4-butanediol (1,4-BD) to 4HB. 4HB containing fermentation broth was used for production of homopolymer poly-4-hydroxybutyrate [P(4HB)] and copolymers poly(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-4HB)]. Recombinant A. hydrophila 4AK4 harboring plasmid pZL-dhaT-aldD containing dhaT and aldD was the most effective 4HB producer, achieving approximately 4 g/l 4HB from 10 g/l 1,4-BD after 48 h of incubation. The strain produced over 10 g/l 4HB from 20 g/l 1,4-BD after 52 h of cultivation in a 6-L fermenter. Recombinant E. coli S17-1 grown on 4HB containing fermentation broth was found to accumulate 83 wt.% of intracellular P(4HB) in shake flask study. Recombinant Ralstonia eutropha H16 grew to over 6 g/l cell dry weight containing 49 wt.% P(3HB-13%4HB) after 72 h.     

Engineering poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer composition in E. coli

A strain of Escherichia coli was metabolically engineered to produce poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) of specified composition between 5% and 18% HV. A gene encoding propionyl-CoA synthetase (prpE from S. enterica) was placed under the control of the IPTG-inducible tac promoter (P(taclacUV5)) while the polyhydroxyalkanoate synthesis operon (phaBCA) from R. eutropha was expressed constitutively. A strain of E. coli harboring both plasmids was grown in defined medium and PHBV was produced with specified hydroxyvalerate (HV) molar content between 5% and 18%. The molecular weight of the copolymer was approximately 700,000 across various HV contents, and average polydispersity was approximately 1.3. The majority of the PHBV production occurred during the late exponential/stationary phase. The HV content of the copolymer generally peaked early in the incubation before falling to its final value. We found that the time profiles of PrpE activity, propionyl-CoA, and acetyl-CoA were well correlated to the HV content time profile. Despite an abundance of propionyl-CoA, incorporation of HV into the copolymer was inefficient. Therefore, both the PHA operon and conditions affecting the availability of propionyl-CoA must be chosen carefully to achieve the desired HV content. The ability to engineer copolymer composition control into an E. coli strain would be useful in cases where the feedstock composition is not adjustable.     

Synthesis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from activated sludge

Poly-3-hydroxybutyrate (PHB) and poly(3-hydroxybutyrate- co-3-hydroxyvalerate) (PHBV) was produced using a co-culture of activated sludge. When butyric acid was used as sole carbon source, PHB was produced. When valeric acid was added to the medium, PHBV was produced. The 3-hydroxyvalerate (3HV) mole fraction in the PHBV reached a maximum of 54% when valeric acid was used as sole carbon source. When the 3HV units in the co-polymer increased from 0.0 to 54.0 mol%, the melting temperature ( T m ) decreased from 178 to 99°C. The composition, and hence the mechanical properties, of the co-polymer produced by activated sludge can be controlled by adjusting the medium composition.     

Enzymatic and non-enzymatic degradation of poly (3-hydroxybutyrate-co-3-hydroxyvalerate) copolyesters produced by Alcaligenes sp. MT-16

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate), poly(3HB-co-3HV), copolyesters with a variety of 3HV contents (ranging from 17 to 60 mol%) were produced by Alcaligenes sp. MT-16 grown on a medium containing glucose and levulinic acid in various ratios, and the effects of hydrophilicity and crystallinity on the degradability of the copolyesters were evaluated. Measurements of thermo-mechanical properties and Fourier-transform infrared spectroscopy in the attenuated total reflectance revealed that the hydrophilicity and crystallinity of poly(3HB-co-3HV) copolyesters decreased as 3HV content in the copolyester increased. When the prepared copolyester film samples were non-enzymatically hydrolysed in 0.01 N NaOH solution, the weights of all samples were found to have undergone no changes over a period of 20 weeks. In contrast, the copolyester film samples were degraded by the action of extracellular polyhydroxybutyrate depolymerase from Emericellopsis minima W2. The overall rate of weight loss was higher in the films containing higher amounts of 3HV, suggesting that the enzymatic degradation of the copolyester is more dependent on the crystallinity of the copolyester than on its hydrophilicity. Our results suggest that the degradability characteristics of poly(3HB-co-3HV) copolyesters, as well as their thermo-mechanical properties, are greatly influenced by the 3HV content in the copolyesters.     

Production of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-4-hydroxybutyrate) by Ralstonia eutropha from soybean oil

High-yield production of polyhydroxyalkanoates (PHAs) by Ralstonia eutropha KCTC 2662 was investigated using soybean oil and γ-butyrolactone as carbon sources. In flask culture, it was shown that R. eutropha KCTC 2662 accumulated PHAs during the growth phase. The optimum carbon to nitrogen ratio (C/N ratio) giving the highest cell and PHA yield was 20 g-soybean oil/g-(NH(4))(2)SO(4). The 4-hydroxybutyrate (4HB) fraction in the copolymer was not strongly affected by the C/N ratio. In a 2.5-L fermentor, a homopolymer of poly(3-hydroxybutyrate) [P(3HB)] was produced from soybean oil as the sole carbon source by batch and fed-batch cultures of R. eutropha with dry cell weights of 15-32 g/L, PHA contents of 78-83 wt% and yields of 0.80-0.82 g-PHA/g-soybean oil used. By co-feeding soybean oil and γ-butyrolactone as carbon sources, a copolymer of poly(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-co-4HB)] could be produced with dry cell weights of 10-21 g/L, yields of 0.45-0.56 g-PHA/g-soybean oil used (0.39-0.50g-PHA/g-carbon sources used) and 4HB fractions of 6-10 mol%. Higher supplementation of γ-butyrolactone increased the 4HB fraction in the copolymer, but decreased cell and PHA yield.     

Production of poly(3-hydroxybutyrate-co-4-hydroxybutyrate) byPseudomonas acidovorans

Summary Terpolyesters of 3-hydroxybutyrate (3HB), 4-hydroxybutyrate (4HB) and 3-hydroxyvarelate (3HV) were produced byPseudomonas acidovorans in nitrogen-free culture solutions of 1,4-butanediol and pentanol. When 1,4-butanediol was used as the sole carbon source, a polyester with an unusually high 4HB fraction of 99 mol% was produced.     

Application of acetyl-CoA acetyltransferase (AtoAD) in Escherichia coli to increase 3-hydroxyvalerate fraction in poly(3-hydroxybutyrate-co-3-hydroxyvalerate)

Polyhydroxyalkanoate (PHA) is a family of biodegradable polymers, and incorporation of different monomers can alter its physical properties. To produce the copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (P(3HB-co-3HV)) containing a high level of 3-hydroxyvalerate (3HV) by altering acetyl-CoA pool levels, we overexpressed an acetyl-CoA acetyltransferase (atoAD) in an engineered E. coli strain, YH090, carrying PHA synthetic genes bktB, phaB, and phaC. It was found that, with introduction of atoAD and with propionate as a co-substrate, 3HV fraction in PHA was increased up to 7.3-fold higher than a strain without atoAD expressed in trans (67.9 mol%). By the analysis of CoA pool concentrations in vivo and in vitro using HPLC and LC-MS, overexpression of AtoAD was shown to decrease the amount of acetyl-CoA and increase the propionyl-CoA/acetyl-CoA ratio, ultimately resulting in an increased 3HV fraction in PHA. Finally, synthesis of P(3HB-co-3HV) containing 57.9 mol% of 3HV was achieved by fed-batch fermentation of YJ101 with propionate.

     

Modification of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) film by chemical graft copolymerization

The graft copolymerization of 2-hydroxyethylmethacrylate (HEMA) onto poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBHV) films has been investigated. The graft copolymerization was conducted in aqueous media using benzoyl peroxide (BPO) as chemical initiator. PHBHV films were prepared by solvent casting. Different parameters affecting the graft yield were studied such as monomer concentration, initiator concentration, and reaction time. The extent of grafting has been modulated by the preparation conditions, in particular the concentration of HEMA. However, it is interesting to note that the initiator concentration had only a slight influence on the graft yield. Characterization of the grafted PHBHV films assumed that the graft copolymerization not only occurred on the film surface but also took place into the film bulk. Differential scanning calorimetry showed that crystallinity dramatically decreased with increasing graft yield, indicating that graft copolymerization hindered the crystallization process. Wettability has been obviously improved by grafting a hydrophilic monomer such as HEMA for high graft yield (>130%).     

Metabolic engineering of Arabidopsis and Brassica for poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer production.

Poly(hydroxyalkanoates) are natural polymers with thermoplastic properties. One polymer of this class with commercial applicability, poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) can be produced by bacterial fermentation, but the process is not economically competitive with polymer production from petrochemicals. Poly(hydroxyalkanoate) production in green plants promises much lower costs, but producing copolymer with the appropriate monomer composition is problematic. In this study, we have engineered Arabidopsis and Brassica to produce PHBV in leaves and seeds, respectively, by redirecting the metabolic flow of intermediates from fatty acid and amino acid biosynthesis. We present a pathway for the biosynthesis of PHBV in plant plastids, and also report copolymer production, metabolic intermediate analyses, and pathway dynamics.     

Production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) depolymerase from Aspergillus sp. NA-25

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) degrading thermophilic fungus was isolated from soil sample collected from waste disposal site, Islamabad, Pakistan. It was able to grow efficiently on a medium containing PHBV as a sole source of carbon and has been identified as Aspergillus sp. NA-25 by 18S rRNA. Using 9% of inoculum maximum production of PHBV depolymerase was observed at 45°C, pH 7.0 in the presence of 0.2% lactose as an additional carbon source. PHBV depolymerase was purified by precipitation with 80% ammonium sulfate and gel filtration chromatography on Sephadex G-75. The four enzyme forms obtained after gel filtration were analyzed on SDS-PAGE and their molecular weights (36, 68, 72 and 90 kDa) were determined. They were characterized on the basis of effect of different temperatures, pH, metal ions and different reagents on the PHBV activity and stability. It is obvious that the fungal strain Aspergillus sp. NA-25 is capable of degrading PHBV with the help of different types of depolymerases.     

Biocompatibility of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolyesters produced byAlcaligenes sp. MT-16

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate), poly(3HB-co-3HV), copolyesters, with 3-hydroxyvalerate (3HV) contents ranging from 17 to 60 mol%, were produced byAlcaligenes sp. MT-16, and their biocompatibility evaluated by the growth of Chinese hamster ovary (CHO) cells and the adsorption of blood proteins and platelets onto their film surfaces. The number of CHO cells that adhered to and grew on these films was higher with increasing 3HV content. In contrast, the tendency for blood proteins and platelets to adhere to the copolyester surfaces significantly decreased with increasing 3HV content. Examination of the surface morphology using atomic force microscopy revealed that the surface roughness was an important factor in determining the biocompatibility of theses copolyesters. The results obtained in this study suggest that poly(3HB-co-3HV) copolyesters, with >30 mol% 3HV, may be useful in biocompatible biomedical applications.     

Biosynthesis and native granule characteristics of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in Delftia acidovorans

The ability of Delftia acidovorans to incorporate a broad range of 3-hydroxyvalerate (3HV) monomers into polyhydroxyalkanoate (PHA) copolymers was evaluated in this study. Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] containing 0–90 mol% of 3HV was obtained when a mixture of sodium 3-hydroxybutyrate and sodium valerate was used as the carbon sources. Transmission electron microscopy analysis revealed an interesting aspect of the P(3HB-co-3HV) granules containing high molar ratios of 3HV whereby, the copolymer granules were generally larger than those of poly(3-hydroxybutyrate) [P(3HB)] granules, despite having almost the same cellular PHA contents. The large number of P(3HB-co-3HV) granules occupying almost the entire cell volume did not correspond to a higher amount of polymer by weight. This indicated that the granules of P(3HB-co-3HV) contain polymer chains that are loosely packed and therefore have lower density than P(3HB) granules. It was also interesting to note that a decrease in the length of the side chain from 3HV to 4-hydroxybutyrate (4HB) corresponded to an increase in the density of the respective PHA granules. The presence of longer side chain monomers (3HV) in the PHA structure seem to exhibit steric effects that prevent the polymer chains in the granules from being closely packed. The results reported here have important implications on the maximum ability of bacterial cells to accumulate PHA containing monomers with longer side chain length.