Novel biodegradable aliphatic poly(butylene succinate-co-cyclic carbonate)s with functional carbonate building blocks. 1. Chemical synthesis and their structural and physical characterization

This study presents chemical synthesis, structural, and physical characterization of novel biodegradable aliphatic poly(butylene succinate-co-cyclic carbonate)s P(BS-co-CC) bearing functional carbonate building blocks. First, five kinds of six-membered cyclic carbonate monomers, namely, trimethylene carbonate (TMC), 1-methyl-1,3-trimethylene carbonate (MTMC), 2,2-dimethyl-1,3-trimethylene carbonate (DMTMC), 5-benzyloxytrimethylene carbonate (BTMC), and 5-ethyl-5-benzyloxymethyl trimethylene carbonate (EBTMC), were well prepared from ethyl chloroformate and corresponding diols at 0 degrees C in THF solution with our modified synthetic strategies. Then, a series of new P(BS-co-CC)s were synthesized at 210 degrees C through a simple combination of poly-condensation and ring-opening-polymerization (ROP) of hydroxyl capped PBS macromers and the prepared carbonate monomers, and titanium tetra-isopropoxide Ti(i-OPr)4 was used as a more suitable catalyst of 5 candidate catalysts which could concurrently catalyze poly-condensation and ROP. By means of NMR, GPC, FTIR, and thermal analytical instruments, macromolecular structures and physical properties have been characterized for these aliphatic poly(ester carbonate)s. The experimental results indicated that novel biodegradable P(BS-co-CC)s were successfully synthesized with number average molecular weight Mn ranging from 24.3 to 99.6 KDa and various CC molar contents without any detectable decarboxylation and that the more bulky side group was attached to a cyclic carbonate monomer, the lower reactivity for its copolymerization would be observed. The occurrences of 13C NMR signal splitting of succinyl carbonyl attributed to the BS building blocks could be proposed due to the randomized sequences of BS and CC building blocks. FTIR characterization indicated two distinct absorption bands at 1716 and 1733 approximately 1735 cm(-1), respectively, stemming from carbonyl stretching modes for corresponding BS and CC units. With regard to their thermal properties, it is seen that the synthesized P(BS-co-CC)s exhibited thermal degradation temperatures 10 approximately 20 degrees C higher than that of PBS. On the basis of the synthesized P(BS-co-BTMC)s, new aliphatic poly(butylene succinate-co-5-hydroxy trimethylene carbonate)s were further synthesized, bearing hydrophilic hydroxyl pendant functional groups through an optimized Pd/C catalyzed hydrogenation. These semi-crystalline new biodegradable aliphatic copolymers with tunable physical properties and functional carbonate building blocks might be expected as potential new biomaterials.     

Novel biodegradable aliphatic poly(butylene succinate-co-cyclic carbonate)s bearing functionalizable carbonate building blocks: II. Enzymatic biodegradation and in vitro biocompatibility assay

In a previous study, we have reported chemical synthesis of novel aliphatic poly(butylene succinate-co-cyclic carbonate) P(BS-co-CC)s bearing various functionalizable carbonate building blocks, and this work will continue to present our new studies on their enzymatic degradation and in vitro cell biocompatibility assay. First, enzymatic degradation of the novel P(BS-co-CC) film samples was investigated with two enzymes of lipase B Candida Antartic (Novozyme 435) and lipase Porcine Pancreas PPL, and it was revealed that copolymerizing linear poly(butylene succinate) PBS with a functionalizable carbonate building block could remarkably accelerate the enzymatic degradation of a synthesized product P(BS-co-CC), and its biodegradation behavior was found to strongly depend on the overall impacts of several important factors as the cyclic carbonate (CC) comonomer structure and molar content, molar mass, thermal characteristics, morphology, the enzyme-substrate specificity, and so forth. Further, the biodegraded residual film samples and water-soluble enzymatic degradation products were allowed to be analyzed by means of proton nuclear magnetic resonance (1H NMR), gel permeation chromatograph (GPC), differential scanning calorimeter (DSC), attenuated total reflection FTIR (ATR-FTIR), scanning electron microscope (SEM), and liquid chromatograph-mass spectrometry (LC-MS). On the experimental evidences, an exo-type mechanism of enzymatic chain hydrolysis preferentially occurring in the noncrystalline domains was suggested for the synthesized new P(BS-co-CC) film samples. With regard to their cell biocompatibilities, an assay with NIH 3T3 mouse fibroblast cell was conducted using the novel synthesized P(BS-co-CC) films as substrates with respect to the cell adhesion and proliferation, and these new biodegradable P(BS-co-CC) samples were found to exhibit as low cell toxicity as the PLLA control, particularly the two samples of poly(butylene succinate-co-18.7 mol % dimethyl trimethylene carbonate) P(BS-co-18.7 mol % DMTMC) and poly(butylene succinate-co-21.9 mol % 5-benzyloxy trimethylene carbonate) P(BS-co-21.9 mol % BTMC) were interestingly found to show much better cell biocompatibilities than the PLLA reference.     

Synthesis and characterization of poly(butylene succinate-co-butylene malate): a new biodegradable copolyester bearing hydroxyl pendant groups

A new biodegradable copolyester, poly(butylene succinate-co-butylene malate) P(BS-co-BM), has been preliminarily prepared with optically active centers and lateral hydroxyl functional groups via a four-step synthetic strategy. First, an optically active benzyl-protected dimethyl malate was synthesized from a starting material of (S)-dimethyl malate and purified with good yield. Then, copolyester poly(butylene succinate-co-benzyl-protected butylene malate), P(BS-co-BBM), was prepared through a skilled condensation copolymerization of the benzyl-protected dimethyl malate, dimethyl succinate, and 1,4-butanediol in the presence of titanium tetraisopropoxide as the catalyst. Finally, a Pd/C catalyzed hydrogenation was applied to eliminate the benzyl protection group in a mixed solution of THF and methanol; thus the target copolyester P(BS-co-BM) was attained. On the other hand, physical properties of the synthesized copolyesters were systematically characterized by means of nuclear magnetic resonance spectrometer, Fourier transformed infrared spectrometer, gel permeation chromatography, optical polarimeter, quantitative hydroxyl titration, and thermal analytical instruments. The experimental evidence demonstrated a successful construction of the product P(BS-co-BM) bearing lateral hydroxyl functional groups. It was also revealed that the lower BBM unit content was in the benzyl-protected optically active P(BS-co-BBM) copolyester, the higher melting point T(m), crystallinity, the broader molecular distribution, and the lower glass transition temperature T(g) would be detected, and these results can be accounted for the presence of bulky lateral benzyl moieties. In contrast, the deprotected product P(BS-co-55 mol % BM) showed a higher T(m), crystallinity and lower T(g) than its counterpart P(BS-co-55 mol % BBM). Interestingly, a thermal stability as high as that of the linear PBS was observed for P(BS-co-55 mol % BM) while a strong BBM unit content dependence of thermal stability was detected for the benzyl-protected copolyester P(BS-co-BBM)s. Therefore, these results may be beneficial for the new optically active P(BS-co-BM) bearing hydrophilic hydroxyl functional groups as a potential biomaterial.     

Synthesis and characterization of biodegradable hyperbranched poly(ester-amide)s based on natural material

A series of novel AB3-type monomers were prepared from nontoxic natural gallic acid and amino acids. These monomers were then melt-polycondensed in the presence of MgO as a catalyst via a transesterification process at 170-190 degrees C to yield the hyperbranched poly(ester-amide)s bearing terminal acetyl groups. FTIR and NMR spectra confirmed the structures of all the monomers and polymers. The degrees of branching, estimated from 1H NMR and quantitative 13C NMR spectra, were 0.50-0.68. These hyperbranched polymers displayed moderately high molecular weights. Hydrolytic and enzymatic degradation studies were carried out in vitro at 37.5 degrees C in NaOH hydrotropic solution and in Tris-HCl buffer (pH = 8.6) containing proteinase K, respectively. The results indicate that the hyperbranched poly(ester-amide)s are degradable hydrolytically as well as enzymatically, and the rate of hydrolytic degradation increases with the pH value of the solution.     

Thermo- and pH-responsive biodegradable poly(alpha-N-substituted gamma-glutamine)s

New double stimuli-responsive poly(alpha-N-substituted gamma-glutamine) has been developed, which was synthesized by the reaction of poly(gamma-glutamic acid) with amino alcohols. Appropriate combinations of the amino alcohols provided the biodegradable poly(amino acid) exhibiting a sharp lower critical solution temperature (LCST) in water. Furthermore, the phase transition temperature was highly sensitive to pH changes.     

Synthesis and characterization of novel biodegradable poly(carbonate ester)s with photolabile protecting groups

Novel biodegradable poly(carbonate ester)s with photolabile protecting groups were synthesized by ring-opening copolymerization of L-lactide (LA) with 5-methyl-5-(2-nitro-benzoxycarbonyl)-1,3-dioxan-2-one (MNC) with diethyl zinc (Et2Zn) as catalyst. The poly(L-lactide-co-5-methyl-5-carboxyl-1,3-dioxan-2-one) (P(LA-co-MCC)) was obtained by UV irradiation of poly(L-lactide acid-co-5-methyl-5-(2-nitro-benzoxycarbonyl)-1,3-dioxan-2-one) (P(LA-co-MNC)) to remove the protective 2-nitrobenzyl group. The free carboxyl groups on the copolymers P(LA-co-MCC) were reacted with paclitaxel, a common antitumor drug. Gel permeation chromatography and NMR studies confirmed the copolymer structures and successful attachment of paclitaxel to the copolymer.     

Self-assembled micelles of biodegradable triblock copolymers based on poly(ethyl ethylene phosphate) and poly(-caprolactone) as drug carriers

A series of novel amphiphilic triblock copolymers of poly(ethyl ethylene phosphate) and poly(-caprolactone) (PEEP-PCL-PEEP) with various PEEP and PCL block lengths were synthesized and characterized. These triblock copolymers formed micelles composed of a hydrophobic core of poly(-caprolactone) (PCL) and a hydrophilic shell of poly(ethyl ethylene phosphate) (PEEP) in aqueous solution. The micelle morphology was spherical, determined by transmission electron microscopy. It was found that the size and critical micelle concentration values of the micelles depended on both hydrophobic PCL block length and PEEP hydrophilic block length. The in vitro degradation characteristics of the triblock copolymers were investigated in micellar form, showing that these copolymers were completely biodegradable under enzymatic catalysis of Pseudomonas lipase and phosphodiesterase I. These triblock copolymers were used for paclitaxel (PTX) encapsulation to demonstrate the potential in drug delivery. PTX was successfully loaded into the micelles, and the in vitro release profile was found to be correlative to the polymer composition. These biodegradable triblock copolymer micelles are potential as novel carriers for hydrophobic drug delivery.     

Synthesis and characterization of triblock copolymers of methoxy poly(ethylene glycol) and poly(propylene fumarate)

Amphiphilic block copolymers were synthesized by transesterification of hydrophilic methoxy poly(ethylene glycol) (mPEG) and hydrophobic poly(propylene fumarate) (PPF) and characterized. Four block copolymers were synthesized with a 2:1 mPEG:PPF molar ratio and mPEGs of molecular weights 570, 800, 1960, and 5190 and PPF of molecular weight 1570 as determined by NMR. The copolymers synthesized with mPEG of molecular weights 570 and 800 had 1.9 and 1.8 mPEG blocks per copolymer, respectively, as measured by NMR, representing an ABA-type block copolymer. The number of mPEG blocks of the copolymer decreased with increasing mPEG block length to as low as 1.5 mPEG blocks for copolymer synthesized with mPEG of molecular weight 5190. At a concentration range of 5-25 wt % in phosphate-buffered saline, copolymers synthesized with mPEG molecular weights of 570 and 800 possessed lower critical solution temperatures (LCST) between 40 and 45 degrees C and between 55 and 60 degrees C, respectively. Aqueous solutions of copolymer synthesized with mPEG 570 and 800 also experienced thermoreversible gelation. The sol-gel transition temperature was dependent on the sodium chloride concentration as well as the mPEG block length. The copolymer synthesized from mPEG 570 had a transition temperature between 40 and 20 degrees C with salt concentrations between 1 and 10 wt %, while the sol-gel transition temperatures of the copolymer synthesized from mPEG molecular weight 800 were higher in the range 75-30 degrees C with salt concentrations between 1 and 15 wt %. These novel thermoreversible copolymers are the first biodegradable copolymers with unsaturated double bonds along their macromolecular chain that can undergo both physical and chemical gelation and hold great promise for drug delivery and tissue engineering applications.     

Synthesis and characterization of poly(L-glutamic acid) gadolinium chelate: a new biodegradable MRI contrast agent

Most currently evaluated macromolecular contrast agents for magnetic resonance imaging (MRI) are not biodegradable. The goal of this study is to synthesize and characterize poly(l-glutamic acid) (PG) gadolinium chelates as biodegradable blood-pool MRI contrast agents. Two PG chelates of gadolinium diethylenetriaminepentaacetic acid (Gd-DTPA) were synthesized through the use of difunctional and monofunctional DTPA precursors. The conjugates were characterized with regard to molecular weight and molecular weight distribution, gadolinium content, relaxivity, and degradability. Distributions of the polymeric MRI contrast agents in various organs were determined by intravenous injection of (111)In-labeled polymers into mice bearing murine breast tumors. MRI scans were performed at 1.5 T in mice after bolus injection of the polymeric chelates. PG-Hex-DTPA-Gd, obtained from aminohexyl-substituted PG and DTPA-dianhydride, was partially cross-linked and was undegradable in the presence of cathepsin B. On the other hand, PG-Bz-DTPA-Gd synthesized directly from PG and monofunctional p-aminobenzyl-DTPA(acetic acid-tert-butyl ester) was a linear polymer and was degradable. The relaxivities of the polymers at 1.5 T were 3-8 times as great as that of Gd-DTPA. Both polymers had high blood concentrations and were primarily accumulated in the kidney. However, PG-Bz-DTPA-Gd was gradually cleared from the body and had significantly less retention in the blood, the spleen, and the kidney. MRI with PG-Bz-DTPA-Gd in mice showed enhanced vascular contrast at up to 2 h after the contrast agent injection. The ability of PG-Bz-DTPA-Gd to be degraded and cleared from the body makes it a favorable macromolecular MRI contrast agent.     

Fabrication and characterization of biodegradable poly(3-hydroxybutyrate) composite containing bioglass

Bacterially derived poly(3-hydroxybutyrate) (P(3HB)) has been used to produce composite films by incorporating Bioglass particles (<5 microm) in 5 and 20 wt % concentrations. P(3HB) was produced using a large scale fermentation technique. The polymer was extracted using the Soxhlet technique and was found to have similar thermal and structural properties to the commercially available P(3HB). The effects of adding Bioglass on the microstructure surface and thermal and mechanical properties were examined using differential scanning calorimetry, dynamic mechanical analysis (DMA), X-ray diffraction, surface interferometry, electron microscopy, and nanoindentation. The addition of increasing concentrations of Bioglass in the polymer matrix reduced the degree of crystallinity of the polymer as well as caused an increase in the glass transition temperature as determined by DMA. The presence of Bioglass particulates reduced the Young's modulus of the composite. The storage modulus and the loss modulus, however, increased with the addition of 20 wt % Bioglass. A short period (28 days) in vitro bioactivity study in simulated body fluid confirmed the bioactivity of the composites, demonstrated by the formation of hydroxyapatite crystals on the composites' surface.     

Synthesis and characterization of new optically active poly(azo-ester-imide)s via interfacial polycondensation

N,N′-Pyromelliticdiimido-di-l-amino acids (1a–1d) were prepared from the reaction of pyromellitic dianhydride with the corresponding l-amino acids in a solution of glacial acetic acid/pyridine (3:2) at refluxing temperature. 4,4′-sulfonyl bis(4,1-phenylene) bis(diazene-2,1-diyl) diphenol, 4,4′-oxy bis(4,1-phenylene) bis(diazene-2,1-diyl) diphenol and 4,4′-methylene bis(4,1-phenylene) bis(diazene-2,1-diyl) diphenol, were prepared from 4,4′-diamino diphenyl sulfone, 4,4′-diamino diphenyl ether, 4,4′-diamino diphenyl methane, sodium nitrite and phenol following the general procedure of diazo coupling. Interfacial polycondensation method was used to prepare the corresponding poly(azo-ester-imid)s (PAEI _1–12 ) in biphasic solution of water/dichloromethane. The resulting polymers (PAEIs) have been obtained in high yields having good inherent viscosities (0.32–0.57 dl g⁻¹), optical activities and thermal stabilities.     

Blends of aliphatic polyesters. VI. Lipase-catalyzed hydrolysis and visualized phase structure of biodegradable blends from poly(epsilon-caprolactone) and poly(L-lactide)

Phase-separated biodegradable polymer blends were prepared from poly(epsilon-caprolactone) (PCL) and poly(L-lactide) (PLLA), and Rhizopus arrhizus lipase-catalyzed hydrolysis and phase structure of the blend films were investigated. Gravimetry revealed that the lipase-catalyzed hydrolysis of PCL in PCL- and PLLA-rich phases is disturbed by the presence of PLLA. Polarimetry confirmed the occurrence of a predominant hydrolysis of PCL and subsequent removal of the hydrolyzed water-soluble PCL oligomers in the blend films. Gravimetry and gel permeation chromatography of the non-blended PLLA film indicated that R. arrhizus lipase has no catalytic effect on the hydrolysis of PLLA. The phase structure of the blend films could be visualized by selective enzymatic removal of one component and subsequent scanning electron microscopic observation.     

Fabrication of biodegradable poly(ester-amide)s based on tyrosine natural amino acid

N,N′-Bis[2-(methyl-3-(4-hydroxyphenyl)propanoate)]isophthaldiamide (5), a novel diol monomer containing chiral group, was prepared by the reaction of S-tyrosine methyl ester (3) with isophthaloyl dichloride (4a). A new family of optically active and potentially biodegradable poly(ester-amide)s (PEAs) based on tyrosine amino acid were prepared by the polycondensation reaction of diol monomer 5 with several aromatic diacid chlorides. The resulting new polymers were obtained in good yields with inherent viscosities ranging between 0.25 and 0.42 dL/g and are soluble in polar aprotic solvents. They showed good thermal stability and high optical purity. The synthetic compounds were characterized and studied by FT-IR, ¹H-NMR, specific rotation, elemental and thermogravimetric analysis (TGA) techniques and typical ones by ¹³C-NMR, differential scanning calorimetry (DSC), X-ray diffraction (XRD), and field emission scanning electron microscopy (FE-SEM) analysis. Soil burial test of the diphenolic monomer 5, and obtained PEA6a, and soil enzymatic assay showed that the synthesized diol and its polymer are biologically active and probably biodegradable in soil environment.     

Synthesis and characterization of biodegradable amphiphilic triblock copolymers containing L-glutamic acid units

A novel biodegradable amphiphilic triblock copolymer bearing pendant carboxyl groups PLGG-PEG-PLGG was successfully prepared by ring-opening copolymerization of l-lactide (LA) with (3s)-benzoxylcarbonylethyl-morpholine-2, 5-dione (BEMD) in the presence of dihydroxyl poly(ethylene glycol) (PEG) as a macroinitiator in bulk at 130 degrees C using SnOct(2) as catalyst and by subsequent catalytic hydrogenation. The copolymer could form micelles in aqueous solution with the cmc dependent on the composition of the copolymer. The micelles exhibited a homogeneous spherical morphology and a unimodal size distribution. Their degradation rate in the presence of proteinase K was faster than that of PLA, and they showed a low degree of cytotoxicity to the articular cartilage cells. This biodegradable amphiphilic block copolymer with pendant carboxyl groups is capable of further modification and is expected to facilitate a variety of potential biomedical applications, such as drug carriers, tissue engineering, etc.     

Synthesis and physical characterization of poly(ethylene glycol)-gelatin conjugates

Poly(ethylene glycol) (PEG) with the terminal group of active ester was coupled to the amino group of gelatin to prepare PEG-grafted gelatin (PEG-gelatin). The affinity chromatographic study revealed that the PEG-gelatin with high degrees of PEGylation did not adsorb onto the gelatin affinity column, in remarked contrast to gelatin alone and the PEG-gelatin with low PEGylation degrees. The former PEG-gelatin showed a critical micelle concentration while it had the apparent molecular size of about 100 nm and a surface charge of almost zero. These findings indicate that the PEG-gelatin formed a micelle structure of which the surface is covered with PEG molecules grafted. When the body distribution of 125I-labeled gelatin and PEG-gelatin after intravenous injection was evaluated, the radioactivity of micellar PEG-gelatin was retained in the blood circulation compared with that of gelatin and the PEG-gelatin of no micelle formation. At the same PEGylation degree, the blood concentration was significantly higher for the PEG-gelatin prepared from PEG with a molecular weight of 12 000 than that of molecular weights of 2000 and 5000. It is concluded that the PEG-gelatin is a drug carrier with a micelle structure which retains in the blood circulation.     

Synthesis and characterization of poly (amino ester) for slow biodegradable gene delivery vector

Many therapeutic carrier materials were exploited for human gene therapy from viral to polymeric vectors. This research describes the evaluation of two biodegradable ester-bonded polymers synthesized by double-monomer polycondensation for a non-viral cationic polymer-based gene delivery system. The backbone was constructed to include inner tertiary amines and outer primary amines. Self-assembly with DNA resulted in the production of regularly nano-sized spherical polyplexes with good transfection efficiency, especially in the presence of serum. The polymers showed a relatively slow degradability for an amine-containing ester polymer, as they maintained DNA/polymer complex for 7 days in physiological buffer conditions. Finally, the low toxicity and slow degradation concluded these polymers reliable for long-term therapeutic applications.     

新型生物可降解塑料——多聚羟基烷酸研究进展

面对日益严重的白色污染 ,人们迫切需要一种能在自然界较快分解的新型塑料。多聚羟基烷酸是原核生物在不平衡代谢条件下形成的碳源和能源贮藏物质 ,这种贮藏物质如同淀粉、糖原一样 ,当生命活动需要时可以再分解利用。由于多聚羟基烷酸有着与石化塑料相似的理化性质 ,又能在一定条件下被微生物迅速而彻底地降解 ,因此是一种理想的传统石化塑料替代品。1　多聚羟基烷酸的理化及生物学特性1 1　多聚羟基烷酸的分子结构及理化性质多聚羟基烷酸是由羟基脂肪酸单体首尾相联构成的高分图 1　多聚羟基烷酸的分子结构子聚合物。又分为不同种类。如多…     

Preparation and crystallization kinetics of new structurally well-defined star-shaped biodegradable poly(L-lactide)s initiated with diverse natural sugar alcohols

This study presents syntheses, structural characterization, and crystallization kinetic investigation of new structurally well-defined star-shaped poly(l-lactide)s (PLLAs). First, a series of new 3- to 6-arm star-shaped PLLAs were synthesized through SnOct(2) catalyzed ring-opening polymerization of (l)-lactide with natural sugar alcohols of glycerol, erythritol, xylitol, and sorbitol as the favorable initiators. Subsequently, their chemical structures were characterized by means of GPC, NMR, and viscometer with respect to the star-shaped structures, demonstrating the well-defined arm structures as evidenced on the g(1/2)/g' values, where g and g' denote the ratios of mean-square radius of gyration and intrinsic viscosity of a star-shaped polymer to those of a linear structural reference with similar absolute molecular weight. Furthermore, spherulite morphologies and growth rates were studied by a polarized microscopy (POM) for the synthesized star-shaped PLLAs with different molecular weights, and it was found that the more arms of a star-shaped PLLA finally resulted in a lower spherulite growth rate. With regard to the crystallization kinetics of these star-shaped PLLAs, isothermal and nonisothermal crystallization were examined by differential scanning calorimeter (DSC). It was found that Avrami exponent n values of isothermal crystallization were almost independent of the isothermal crystallization temperature T(c) for different series of star-shaped PLLAs. In contrast, the values of Avrami exponent n were observed to strongly depend on the star-shaped structures with different arms, implying their distinct nucleation mechanisms, and the more arms of a star-shaped PLLA led to a slower isothermal crystallization rate. On the basis of a modified Avrami equation, new light was shed on the nonisothermal crystallization kinetics for the star-shaped PLLAs, and the activation energies were found to vary from 146.86 kJ/mol for the linear PLLA EG-3 to 221.23 kJ/mol of the star-shaped S-3, demonstrating much decreased crystallizabilities of star-shaped PLLAs with more arms.     

Amphiphilic poly(L-lactide)-b-dendritic poly(L-lysine)s synthesized with a metal-free catalyst and new dendron initiators: chemical preparation and characterization

This study presents investigations on new approaches to novel biodegradable amphiphilic poly(L-lactide)-b-dendritic poly(L-lysine)s bearing well-defined structures. First, two new Boc-protected poly(L-lysine) dendron initiators G(2)OH 4 (generation = 2) and G(3)OH 6 (generation = 3) with hydroxyl end functional groups were efficiently derived from corresponding precursors 3 and 5 via methyl ester substitution with ethanolamine. Subsequently, two series of new diblock copolymers of poly(L-lactide)-b-dendritic Boc-protected poly(L-lysine)s (S1-S2, S3-S4) were prepared in chloroform through ring-opening copolymerization of poly(L-lactide)s with a metal-free catalyst of organic 4-(dimethylamino) pyridine (DMAP) in the presence of a corresponding new poly(L-lysine) dendron initiator. Further, molecular structures of the prepared new dendron initiators as well as those of poly(L-lactide)-b-dendritic Boc-protected poly(L-lysine)s bearing different dendron blocks and PLLA lengths were examined by means of nuclear magnetic resonance spectroscopy (NMR), gel permeation chromatography (GPC), mass spectrometry (ESI-MS, MALDI-FTMS), and thermal gravimetric analysis (TGA). The results demonstrated successful formation of the synthetic precursors, functional dendron initiators, and new diblock copolymers. In addition, the very narrow molecular weight distributions (PDI = 1.10-1.14) of these poly(L-lactide)-b-dendritic Boc-protected poly(L-lysine)s further indicated their well-defined molecular structures. After the efficient Boc-deprotection for the dendron amino groups with TFA/CH(2)Cl(2), new diblock poly(L-lactide)-b-dendritic poly(L-lysine)s bearing lipophilic PLLA and hydrophilic dendritic PLL were finally prepared. It was noteworthy that the MALDI-FTMS result showed that no appreciable intermolecular chain transesterification happened during the ROP of L-lactide catalyzed by the DMAP. Moreover, self-assembly of these new biodegradable amphiphilic copolymers in diverse solvents were also preliminarily studied.