Upgrading the preparation of high-quality chitosan from Procambarus clarkii wastes over the traditional isolation of shrimp chitosan

Crustacean waste is one of the most severe issues, posing significant environmental and health risks. This study aims to improve managing marine waste by isolating chitosan from Procambarus clarkii by devising a new methodology, incorporating technical steps, e.g., washing, decolorization and deacetylation under a reflexive condenser and dialysis purification. A comparison was made between the prepared P. clarkii chitosan and four types of shrimp chitosans: commercial, high, low, and nano. The obtained chitosan has a low molecular weight and viscosity compared to the commercial shrimp chitosan used in various applications. P. clarkii chitosan was prepared in high quality from a cheap source, as its color and quality were better than those of the commercial shrimp chitosan. The new methodology has successfully extracted chitosan from P. clarkii in a good quality and high purity, achieving 89% deacetylation, high solubility, high purity, and medium molecular weight. Analysis of the different chitosan samples with Fourier transform infrared spectroscopy (FTIR), atomic force microscopy, Raman spectrum referred indicated high similarity between the chitosan different types, regardless of its source. The 3D image of P. clarkii showed the distance between the highest and most profound points of extracted chitosan is 728.94 nm, revealing homogeneous, smooth surfaces, apparently free of pores and cracks. FTIR and Raman spectrum of P. clarkii indicated various functional groups, e.g., alcohol, amines, amides, and phenols. These active groups are responsible for about 60% of the antioxidant activity of that product. Evaluating the quality traits indicated the excellence of the chitosan prepared from P. clarkii, especially in color, viscosity, and antioxidant activity, nominating it for different food applications.     

Antifungal potentiality of mycogenic silver nanoparticles capped with chitosan produced by endophytic Amesia atrobrunnea

This research reports the fabrication of silver nanoparticles (AgNPs) from endophytic fungus, Amesia atrobrunnea isolated from Ziziphus spina-christi (L.). Influencing factors for instance, thermal degree of incubation, media, pH, and silver nitrate (AgNO₃) molarity were optimized. Then, the AgNPs were encapsulated with chitosan (Ch-AgNPs) under microwave heating at 650 W for 90 s. Characterization of nanoparticles was performed via UV–visible (UV–vis) spectrophotometer, Fourier-transform infrared spectrophotometer (FTIR), zeta potential using dynamic-light scattering (DLS), and field-emission-scanning electron microscope (FE-SEM). Anti-fungal activity of Ch-AgNPs at (50, 25, 12.5, 6.25 mg/L) was tested against Fusarium oxysporum, Curvularia lunata, and Aspergillus niger using the mycelial growth inhibition method (MGI). Results indicated that Czapek-dox broth (CDB) with 1 mM AgNO₃, an acidic pH, and a temperature of 25–30 °C were the optimum for AgNPs synthesis. (UV–vis) showed the highest peak at 435 nm, whereas Ch-AgNPs showed one peak for AgNPs at 405 nm and another peak for chitosan at 230 nm. FTIR analysis confirmed that the capping agent chitosan was successfully incorporated and interacted with the AgNPs through amide functionalities. Z-potential was −19.7 mV for AgNPs and 38.9 mV for Ch-AgNPs, which confirmed the significant stability enhancement after capping. FES-SEM showed spherical AgNPs and a reduction in the nanoparticle size to 44.65 nm after capping with chitosan. The highest mycelial growth reduction using fabricated Ch-AgNPs was 93% for C. lunata followed by 77% for A. niger and 66% F. oxysporum at (50 mg/L). Biosynthesis of AgNPs using A. atrobrunnea cell-free extract was successful. Capping with chitosan exhibited antifungal activity against fungal pathogens.     

Rapid harvesting of freshwater microalgae using chitosan

In this study, chitosan was used as a flocculant to harvest freshwater microalgae Chlorella vulgaris. The recovery efficiency of C. vulgaris was tested at various chitosan concentrations. 120 mg/L of chitosan showed the highest efficiency (92 ± 0.4%) within 3 min. The maximum concentration factor of 10 was also achieved at this dose of chitosan. The harvesting efficiency was pH dependent. pH 6.0 showed the highest harvesting efficiency (99 ± 0.5%). Measurement of zeta-potential confirmed that the flocculation was induced by charge neutralization. This study showed that a biopolymer, chitosan, can be a promising flocculant due to its high efficacy, low dose requirements, and short settling time.     

Substituted polyaniline/chitosan composites: Synthesis and characterization

Substituted polyaniline/chitosan(PANIs/Ch) composites were chemically synthesized by using ammonium peroxydisulfate as oxidant and characterized by measurements of conductivity, FTIR, UV–vis, SEM and TGA techniques. FTIR spectra of the composites revealed that there is a strong interaction between substituted polyanilines and chitosan. Among the substituted polyaniline/chitosan composites synthesized, poly(N-ethylaniline)/chitosan PNEANI/Ch has the highest conductivity with a value of 1.68 × 10^?4 S/cm. The P2EANI/Ch composite exhibited higher thermal stability than the other composites. SEM images of the composites showed an agglomerated granular morphology of substituted polyaniline particles coated on the surface of chitosan.     

Methylated N-(4-N,N-dimethylaminobenzyl) chitosan as effective gene carriers: Effect of degree of substitution

The objective of this study was to investigate the transfection efficiency of quaternized N-(4-N,N-dimethylaminobenzyl) chitosan; TM-Bz-CS, using the plasmid DNA encoding green fluorescent protein (pEGFP-C2) on human hepatoma cell lines (Huh7 cells). The factors affecting the transfection efficiency e.g. degree of quaternization (DQ), the degree of dimethylaminobenzyl substitution (DS) and polymer/DNA weight ratio, have been evaluated. The results revealed that all TM-Bz-CS derivatives were able to condense with DNA. Illustrated by agarose gel electrophoresis, complete complexes of TM₅₇-Bz₄₂-CS/DNA were formed at weight ratio of above 0.5, whereas those of TM₄₇-Bz₄₂-CS/DNA and TM₅₇- Bz₁₇-CS/DNA were above 1. The rank of transfection efficiency of the chitosan derivatives were TM₅₇-Bz₄₂-CS > TM₄₇-Bz₄₂-CS > TM₅₇-Bz₁₈-CS. The pH of culture medium did not affect the transfection efficiency of TM₅₇-Bz₄₂-CS/DNA complex, whereas it affected the transfection efficiency of chitosan/DNA complex. The results indicated that the improved gene transfection was due to the hydrophobic group (N,N-dimethylaminobenzyl) substitution on chitosan which promoted the interaction and condensation with DNA as well as N-quaternization which increased chitosan water solubility and enhance gene expression. For cytotoxicity studies, TM-Bz-CS was safe at the concentration of the highest transfection. In conclusion, this novel chitosan derivative, TM₅₇-Bz₄₂-CS showed elevated potential as gene carrier by efficient DNA condensation and mediated highest level of gene transfection with negligible cytotoxicity in Huh7 cells.     

Multidimensional optimization of promising antitumor xanthone derivatives

A promising antitumor xanthone derivative was optimized following a multidimensional approach that involved the synthesis of 17 analogues, the study of their lipophilicity and solubility, and the evaluation of their growth inhibitory activity on four human tumor cell lines. A new synthetic route for the hit xanthone derivative was also developed and applied for the synthesis of its analogues. Among the used cell lines, the HL-60 showed to be in general more sensitive to the compounds tested, with the most potent compound having a GI₅₀ of 5.1 μM, lower than the hit compound. Lipophilicity was evaluated by the partition coefficient (K_p) of a solute between buffer and two membrane models, namely liposomes and micelles. The compounds showed a log K_p between 3 and 5 and the two membrane models showed a good correlation (r² = 0.916) between each other. Studies concerning relationship between solubility and structure were developed for the hit compound and 5 of its analogues.     

Improved yield and stability of amylase by multipoint covalent binding on polyglutaraldehyde activated chitosan beads: Activation of denatured enzyme molecules by calcium ions

In this study raw starch digesting amylase (RSDA) from Aspergillus carbonarius (Bainier) Thom IMI 366159 was stabilized by covalent binding on polyglutaraldehyde (PG), glutaraldehyde (G) activated chitosan beads or post immobilization cross linking of enzyme adsorbed on chitosan. Presence of Ca²⁺ ions (0.5–1.5 mM) activated the PG and G derivatives but repressed the crosslinked enzyme. Optimum pH for cross linked derivative increased by 2 units but was unaltered for PG and G derivatives. Immobilized amylase exhibited improved thermal and storage stability. Immobilized derivatives had no loss of activity after 1 month storage and retained above 90% activity after 10 batch reactions of 60 min each. Immobilization successfully stabilized RSDA and immobilized enzyme from A. carbonarius can be applied in numerous industries for cheap, cost effective and environmentally friendly starch hydrolytic processes to simple sugars.     

Immunotherapeutic effects of chitin in comparison with chitosan against Leishmania major infection

Chitin and chitosan microparticles (MPs) are important immune system stimulators. The aim of this study was to evaluate the protective effects of these compounds in comparison with each other against Leishmania infection in BALB/c mice infected with Leishmania major (L. major).Female BALB/c mice were injected subcutaneously with 2 × 10⁵ promastigotes. Chitin and/or chitosan MPs (< 40 μm) were subcutaneously injected in the BALB/c mice with two-day intervals until two weeks. Mice in all groups were sacrificed at 12 weeks post-infection. Enumeration of viable parasites was performed using limiting dilution assay. Furthermore, the animals (5 mice/group) were sacrificed two weeks post-infection. The lymph node cells were isolated and the effects of the chitinous MPs on the proliferation and production of cytokines such as tumor necrosis factor alpha (TNF-α) and interleukin-10 (IL-10) were determined. The mean sizes of lesions were significantly smaller in chitin (0.6 ± 0.12 mm) and chitosan treated groups (1.2 ± 0.8 mm) than in the control group (6.2 ± 1.7 mm) (P < 0.05). The parasite load in the lymph nodes of the treated mice was significantly lower than that in the lymph nodes of controls (1.31 × 10⁶ vs 8.24 × 10⁷ parasite/lymph node [P = 0.032] and 7.49 × 10⁶ vs 8.24 × 10⁷ parasite/lymph node [P = 0.05] for chitin and chitosan MPs treatment, respectively). We found that chitinous MPs induced cell proliferation and that chitin but not chitosan increased TNF-α and IL-10 production. Chitin appears that it has more effect than chitosan against leishmaniasis. The current study revealed that chitinous MPs had significant activity against L. major and could be considered as new therapeutic modality in leishmaniasis.     

Immobilizing cholesterol oxidase in chitosan–alginic acid network

Proton conducting biopolymer networks have potential use for bio-sensors. The cost-effective, non-hazardous and environmentally safe biopolymer, such as chitosan, is an attractive feature for bio-sensors. Cholesterol oxidase was immobilized in conducting network via complexation of chitosan with alginic acid. A method for the preparation of the complex along with characterization by elemental analysis, FTIR spectroscopy, TGA and DSC were reported. The proton conductivity chitosan–alginic acid network was studied via impedance spectroscopy under humidified condition. The complex polymer electrolyte with x = 1 exhibited maximum proton conductivity of 1.4 × 10^?3 S/cm at RT, RH ～ 50%. The potential use of this network in enzyme immobilization was studied by manufacturing cholesterol oxidase entrapped polymer networks. Additionally, the maximum reaction rate (V_max) and Michaelis–Menten constant (K_m) were investigated for the immobilized cholesterol oxidase. Also, temperature and pH optimization studies were performed, and operational stability and shelf life of the polymer network were examined.     

Cross-linking chitosan into UV-irradiated cellulose fibers for the preparation of antimicrobial-finished textiles

Chitosan cross-linked cellulose fibers were prepared using non-toxic procedures in order to confer antimicrobial properties to cellulose fibers. Citric acid was used as the cross-linker and NaH₂PO₄ as catalyst in previously UV-irradiated cellulose fibers. Further heat dried-cure process and washing with detergent, water and acetic acid (0.1 M) gave a maximum incorporation of chitosan of 27 mg per gram of functionalized textile. The thermogravimetric analysis of the material with the highest chitosan content showed an increased thermal stability compared to cellulose and chitosan. The UV-irradiation induced morphological changes, such as less entangled cellulose fibers, as observed by scanning electron microscopy, which was prompted to enhance the chitosan incorporation. The biomass and spore germination percentage of Penicillium chrysogenum and colony forming units per millilitre for Escherichia coli decreased significantly on the composed materials as compared to raw cellulose fiber and it was similar to that obtained with a commercial antimicrobial cellulose fiber.     

Comparison of the efficacy of chitosan with that of a fluorescent pseudomonad for the control of Fusarium head blight disease of cereals and associated mycotoxin contamination of grain

Fusarium culmorum can cause Fusarium head blight (FHB) disease of cereals, resulting in yield loss and contamination of grain with the trichothecene mycotoxin, deoxynivalenol (DON). In this study, we compared the efficacy of a biological control agent (Pseudomonas fluorescens strain MKB 158) with the biochemical chitosan (the deacetylated derivative of chitin) in controlling FHB disease of wheat and barley. Both agents were equally effective in reducing DON contamination of grain caused by F. culmorum. Under both glasshouse and field conditions, treatment with commercially available crabshell-derived chitosan reduced the severity of FHB symptom development on wheat and barley by ?74% (P ? 0.050). While treatment with P. fluorescens reduced the severity of FHB symptom development on these cereals by ?48% (P ? 0.050). Chitosan and P. fluorescens respectively prevented ?58 and ?35% of the FHB-associated reductions in 1000-grain weight in wheat and barley (P ? 0.050). Both agents significantly reduced the DON content of wheat and barley under both glasshouse and field conditions (P ? 0.050) and were equally efficacious in doing so (?74 and ?79% reductions due to chitosan and P. fluorescens, respectively). Crude chitin extracts from crabshells and crude chitosan-based formulations prepared from crabshells and eggshells were also tested under field conditions, but were not as effective as the commercial crabshell-derived preparation in controlling FHB disease. This is the first report on the use of chitosan for the control of Fusarium head blight disease and DON contamination of grain.     

Physicochemical characterization of chitin and chitosan from crab shells

Crab chitosan was prepared by alkaline N-deacetylation of crab chitin for 60, 90 and 120 min and the yields were 30.0-32.2% with that of chitosan C120 being the highest. The degree of N-deacetylation of chitosans (83.3–93.3%) increased but the average molecular weight (483–526 kDa) decreased with the prolonged reaction time. Crab chitosans showed lower lightness and WI values than purified chitin, chitosans CC and CS but higher than crude chitin. With the prolonged reaction time, the nitrogen (8.9–9.5%), carbon (42.2–45.2%) and hydrogen contents (7.9–8.6%) in chitosans prepared consistently increased whereas N/C ratios remained the same (0.21). Crab chitosans prepared showed a melting endothermic peak at 152.3–159.2 °C. Three chitosans showed similar microfibrillar crystalline structure and two crystalline reflections at 2θ = 8.8–9.0° and 18.9–19.1°. Overall, the characteristics of three crab chitosans were unique and differed from those of chitosan CC and CS as evidenced by the element analysis, differential scanning calorimetry, scanning electron microscopy and X-ray diffraction patterns.     

Preparation and characterization of cellulose/chitosan blend films

Cellulose and chitosan were mixed in N-methylmorpholine-N-oxide (NMMO) and heated to 100 °C, and then were processed under a pressure of 70 kg/cm² exerted by a compression molding machine at 100 °C for 8 min. As a result, transparent orange viscose films were obtained. After rinsing with deionized water and drying transparent yellowish blend films were obtained. Scanning electron microscope (SEM) indicated that when the chitosan content in the blend increased up to 3% the surface structure became smoother, but the film containing 5% (w/w) chitosan, became coarse again probably due to phase separation. Tensile strength test results were consistant with this. Antibacterial assessment proved that addition of chitosan to the films results in slight antibacterial properties. The halo zone test confirmed that the blend films made in this research have non-diffusible antibacterial properties.     

Preparation and pharmacodynamics of low-molecular-weight chitosan nanoparticles containing insulin

Low-molecular-weight chitosan (LMWC) was obtained by enzymatic degradation and ultrafiltration separation. LMWC nanoparticles with LMWC having 20 kDa weight average molecular weight (M_w) were then prepared by solvent evaporation method. The resultant nanoparticles were spherical with a narrow particle size distribution. LMWC nanoparticles loaded with insulin as a model drug were prepared. The average entrapment efficiency of insulin could reach up to 95.54%. The in vitro drug release profiles from the nanoparticles showed an initial burst of release in the first 2 h, followed by zero order release kinetics. In vivo pharmacodynamics of chitosan nanoparticles containing insulin showed that the nanoparticles showed some hypoglycemic activity. Compared with an insulin solution, a relative bioavailability of 0.737 was observed for four times the dosage of insulin in the chitosan nanoparticles after pulmonary administration.     

Synthesis,characterization and antifungal activity of quaternary derivatives of chitosan on Aspergillus flavus

Two series of new chitosan derivatives were synthesized by reaction of deacetylated chitosan (CH) with propyl (CH-Propyl) and pentyl (CH-Pentyl) trimethylammonium bromides to obtain derivatives with increasing degrees of substitution (DS). The derivatives were characterized by ¹H NMR and potentiometric titration techniques and their antifungal activities on the mycelial growth of Aspergillus flavus were investigated in vitro. The antifungal activities increase with DS and the more substituted derivatives of both series, CH-Propyl and CH-Pentyl, exhibited antifungal activities respectively three and six times higher than those obtained with commercial and deacetylated chitosan. The minimum inhibitory concentrations (MIC) were evaluated at 24, 48 and 72 h by varying the polymer concentration from 0.5 to 16 g/L and the results showed that the quaternary derivatives inhibited the fungus growth at polymer concentrations four times lower than that obtained with deacetylated chitosan (CH). The chitosans modified with pentyltrimethylammonium bromide exhibited higher activity and results are discussed taking into account the degree of substitution (DS).     

Selective and stable production of physiologically active chitosan oligosaccharides using an enzymatic membrane bioreactor

We investigated the production of chitosan oligosaccharides by continuous hydrolysis of chitosan in an enzyme membrane bioreactor, with the goal of improving the yield of physiologically active oligosaccharides (pentamers and hexamers) and achieving operational stability. The bioreactor was a continuous-flow stirred-tank reactor equipped with an ultrafiltration membrane with a molecular weight cut-off of 2000 Da, and the hydrolysis was accomplished with chitosanase from Bacillus pumilus. After optimization of the reaction parameters, such as the amount of enzyme, the yield of the target oligosaccharides produced in the membrane bioreactor with free chitosanase reached 52% on the basis of the fed concentration of chitosan. An immobilized chitosanase prepared by the multipoint attachment method was used to improve the operational stability of the membrane bioreactor. Under the optimized conditions, pentameric and hexameric chitosan oligosaccharides were steadily produced at 2.3 g/L (46% yield) for a month. The half-life of the productivity of the reactor was estimated to be 50 d under the conditions examined.     

Identification and simultaneous determination of p-FHA and p-FBA,two metabolites of anti-tumor agent—Fluorapacin in rat urine

Fluorapacin, bis(4-fluorobenzyl)trisulfide, a small molecule natural product derivative of trisulfide, has revealed a broad spectrum of anti-proliferative activity and in vivo anti-tumor efficacy in human xenograft mice models with excellent safety profile. In the present study, two new metabolites, para-fluorohippuric acid (p-FHA) and para-fluorobenzoic acid (p-FBA), were identified by GC–MS and HPLC as the main metabolites in urine of rats after intravenous administration of fluorapacin. A simple HPLC-UV method for simultaneous determination of these two metabolites in urine has been developed and validated. The newly developed method demonstrated excellent specificity, accuracy, precision, and stability. This method was successfully employed to study the urinary excretion of fluorapacin in rats. The results indicated that p-FHA was the major metabolite in urine, and the total excretion recovery of p-FHA and p-FBA was 67.6 ± 4.9% (mean ± SE, n = 6) of dosage after 48 h of administration.     

Acylated flavonol pentaglycosides from Baphia nitida leaves

Two new acylated flavonol pentaglycosides were isolated from the butanolic extract of Baphia nitida leaves by Sephadex LH-20 and preparative HPLC. Structural elucidation of kaempferol 3-O-β-d-xylopyranosyl(1 → 3)-(4-O-E-p-coumaroyl-α-l-rhamnopyranosyl(1 → 2))[β-d-glucopyranosyl(1 → 6)]-β-d-galactopyranoside-7-O-α-l-rhamnopyranoside (1) and kaempferol 3-O-β-d-xylopyranosyl(1 → 3)-(4-O-Z-p-coumaroyl-α-l-rhamnopyranosyl(1 → 2))[β-d-glucopyranosyl(1 → 6)]-β-d-galactopyranoside-7-O-α-l-rhamnopyranoside (2) was achieved using UV, NMR, and mass spectrometry, indicating the presence of trans or cis isomers of p-coumaric acid moiety in these novel structures. The antioxidant activity of the two compounds was assessed in the peroxynitrite assay.     

Improved reproducibility in the determination of the molecular weight of chitosan by analytical size exclusion chromatography

The reproducibility of the determination of the molecular weight of chitosans in the 90–210 kDa range (M_n) by analytical size exclusion chromatography with multi-angle laser light scattering (SEC-MALLS) was improved by reducing the salt concentration in the mobile phase from (0.3 M acetic acid, 0.2 M sodium acetate, and 0.8 mM sodium azide) to (0.15 M acetic acid, 0.1 M sodium acetate, and 0.4 mM sodium azide) using Tosoh TSKgel G6000PW_XL and G5000PW_XL columns in series. The variability of measured molecular weight was significantly reduced by lowering the acetate concentration in the mobile phase, while the average molecular weight did not change significantly. The coefficient of variation of the number-average molecular weight, CV(M_n), decreased from 7–12% to 3–6% upon mobile phase dilution. This reduced variability in molecular weight of chitosans obtained from SEC is a significant improvement when precise values of chitosan molecular weight are required, for example in stability studies where viscosity changes in concentrated chitosan solutions are assessed, and in gene delivery applications.     

Production of (R)-mandelic acid by immobilized cells of Saccharomyces cerevisiae on chitosan carrier

The asymmetric microbial reduction of phenylglyoxylic acid (PGA) to (R)-mandelic acid ((R)-MA) with immobilized Saccharomyces cerevisiae cells on globular chitosan was studied. The immobilization conditions and characterization of the immobilized cells were carried out. Chitosan–acetic acid solution was injected into a mixture of 20% NaOH and 30% CH₃OH aqueous solution to obtain globular chitosan, and then the globular chitosan was treated with 1% solution of glutaraldehyde to immobilize yeast cells, which were used to synthesize (R)-MA. The optimum conditions were identified as the substrate concentration of 10 mmol L⁻¹, pH of 6.5 and reaction temperature of 30 °C with the yield of 62% for (R)-MA and the enantiomeric excess (e.e.) of 98% for (R)-MA. The immobilized cells showed good operation and storage stability.