Production in Escherichia coli of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) with differing monomer compositions from unrelated carbon sources

The industrial production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) has been hindered by high cost and a complex control strategy caused by the addition of propionate. In this study, based on analysis of the PHBV biosynthesis process, we developed a PHBV biosynthetic pathway from a single unrelated carbon source via threonine biosynthesis in Escherichia coli. To accomplish this, we (i) overexpressed threonine deaminase, which is the key factor for providing propionyl-coenzyme A (propionyl-CoA), from different host bacteria, (ii) removed the feedback inhibition of threonine by mutating and overexpressing the thrABC operon in E. coli, and (iii) knocked out the competitive pathways of catalytic conversion of propionyl-CoA to 3-hydroxyvaleryl-CoA. Finally, we constructed a series of strains and mutants which were able to produce the PHBV copolymer with differing monomer compositions in a modified M9 medium supplemented with 20 g/liter xylose. The largest 3-hydroxyvalerate fraction obtained in the copolymer was 17.5 mol%.     

Synthesis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from activated sludge

Poly-3-hydroxybutyrate (PHB) and poly(3-hydroxybutyrate- co-3-hydroxyvalerate) (PHBV) was produced using a co-culture of activated sludge. When butyric acid was used as sole carbon source, PHB was produced. When valeric acid was added to the medium, PHBV was produced. The 3-hydroxyvalerate (3HV) mole fraction in the PHBV reached a maximum of 54% when valeric acid was used as sole carbon source. When the 3HV units in the co-polymer increased from 0.0 to 54.0 mol%, the melting temperature ( T m ) decreased from 178 to 99°C. The composition, and hence the mechanical properties, of the co-polymer produced by activated sludge can be controlled by adjusting the medium composition.     

Biosynthesis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from structurally unrelated single carbon sources by newly isolated Pseudomonas sp. EL-2

Summary A Pseudomonas sp. EL-2 strain capable of synthesizing poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] was isolated from activated sludge. For simulation of P(3HB-co-3HV) production in the cells, deficiency of nutrients such as NH₄ ⁺, SO₄ ^2- and Mg²⁺ was crucial and the maximum content of P(3HB-co-3HV) could reach 46% on NH₄ ⁺-deficient medium. This organism synthesized P(3HB-co-3HV) with 3HV monomer in the range from 1.9 to 49.3 mol% from unrelated single carbon sources such as glucose, fructose, propionate, or sorbitol. P(3HB-co-3HV)s containing a higher fraction of 3HV were produced by adding propionic acid to glucose medium.     

Viscoelastic relaxations and thermal properties of bacterial poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and poly(3-hydroxybutyrate-co-4-hydroxybutyrate)

3-Hydroxybutyrate-3-hydroxyvalerate (3HB-3HV) as well as 3-hydroxybutyrate-4-hydroxybutyrate (3HB-4HB) copolyesters have been investigated by differential scanning calorimetry, thermogravimetric analysis and dynamic mechanical spectroscopy, over a wide range of compositions (0-95 mol% 3HV; 0-82 mol% 4HB). Both series of isolated copolyesters are partially crystalline at all compositions. Quenched samples show a glass transition that decreases linearly with increasing co-monomer molar fraction, more markedly when the co-monomer is 4HB. Above Tg, all copolyesters, rich in 3HB units, show a cold crystallization phenomenon followed by melting, while at the other end crystallization on heating is observed only in 3HB-3HV copolymers. The viscoelastic spectrum, strongly affected by thermal history, shows two relaxation regions: the glass transition, whose location depends on copolymer type and composition, and a secondary dispersion region at low temperatures (-130/-80 degrees C). The latter results from a water-related relaxation analogous to that of P(3HB) and, in 3HB-4HB copolymers, from another overlapping absorption peak centered at -130 degrees C, attributed to local motion of the methylene groups in the linear 4HB units.     

Microbial degradation of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in soils

[This corrects the article on p. 3236 in vol. 59.].     

Microbial degradation of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in soils.

The microbial degradation of tensile test pieces made of poly(3-hydroxybutyrate) [P(3HB)] or a copolymer of 90% 3-hydroxybutyric acid and 10% 3-hydroxyvaleric acid was studied in soils incubated at a constant temperature of 15, 28, or 40 degrees C for up to 200 days. In addition, hydrolytic degradation in sterile buffer at temperatures ranging from 4 to 55 degrees C was monitored for 98 days. Degradation was measured through loss of weight (surface erosion), molecular weight, and mechanical strength. While no weight loss was recorded in sterile buffer, samples incubated in soils were degraded at an erosion rate of 0.03 to 0.64% weight loss per day, depending on the polymer, the soil, and the incubation temperature. The erosion rate was enhanced by incubation at higher temperatures, and in most cases the copolymer lost weight at a higher rate than the homopolymer. The molecular weights of samples incubated at 40 degrees C in soils and those incubated at 40 degrees C in sterile buffer decreased at similar rates, while the molecular weights of samples incubated at lower temperatures remained almost unaffected, indicating that molecular weight decrease is due to simple hydrolysis and not to the action of biodegrading microorganisms. The degradation resulted in loss of mechanical properties. From the samples used in the biodegradation studies, 295 dominant microbial strains capable of degrading P (3HB) and the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer in vitro were isolated and identified.(ABSTRACT TRUNCATED AT 250 WORDS)     

In vitro biocompatibility of electrospun poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) fiber mats

In the present contribution, the potential for use of the ultrafine electrospun fiber mats of poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) as scaffolding materials for skin and nerve regeneration was evaluated in vitro using mouse fibroblasts (L929) and Schwann cells (RT4-D6P2T) as reference cell lines. Comparison was made with PHB and PHBV films that were prepared by solution-casting technique. Indirect cytotoxicity assessment of the as-spun PHB and PHBV fiber mats with mouse fibroblasts (L929) and Schwann cells (RT4-D6P2T) indicated that the materials were acceptable to both types of cells. The attachment of L929 on all of the fibrous scaffolds was significantly better than that on both the film scaffolds and tissue-culture polystyrene plate (TCPS), while RT4-D6P2T appeared to attach on the flat surfaces of TCPS and the film scaffolds much better than on the rough surfaces of the fibrous scaffolds. For L929, all of the fibrous scaffolds were superior in supporting the cell proliferation to the film counterparts, but inferior to TCPS at days 3 and 5, while, for RT4-D6P2T, the rough surfaces of the fibrous scaffolds appeared to be very poor in supporting the cell proliferation when comparing with the smooth surfaces of TCPS and the film scaffolds. Scanning electron microscopy was also used to observe the behavior of both types of cells that were cultured on both the fibrous and the film scaffolds and glass substrate for 24 h.     

Production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) depolymerase from Aspergillus sp. NA-25

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) degrading thermophilic fungus was isolated from soil sample collected from waste disposal site, Islamabad, Pakistan. It was able to grow efficiently on a medium containing PHBV as a sole source of carbon and has been identified as Aspergillus sp. NA-25 by 18S rRNA. Using 9% of inoculum maximum production of PHBV depolymerase was observed at 45°C, pH 7.0 in the presence of 0.2% lactose as an additional carbon source. PHBV depolymerase was purified by precipitation with 80% ammonium sulfate and gel filtration chromatography on Sephadex G-75. The four enzyme forms obtained after gel filtration were analyzed on SDS-PAGE and their molecular weights (36, 68, 72 and 90 kDa) were determined. They were characterized on the basis of effect of different temperatures, pH, metal ions and different reagents on the PHBV activity and stability. It is obvious that the fungal strain Aspergillus sp. NA-25 is capable of degrading PHBV with the help of different types of depolymerases.     

Renewable resource-based green composites from recycled cellulose fiber and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) bioplastic

Novel "green" composites were successfully fabricated from recycled cellulose fibers (RCF) and a bacterial polyester, poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) by melt mixing technique. Various weight contents (15%, 30%, and 40%) of the fibers were incorporated in the PHBV matrix. The effect of the fiber weight contents on the thermal, mechanical, and dynamic-mechanical thermal properties of PHBV was investigated and a comparative property analysis was performed with RCF-reinforced polypropylene (PP) composites. The tensile and storage moduli of the PHBV-based composites were improved by 220% and 190%, respectively, by reinforcement with 40 wt % RCF. Halpin-Tsai and Tsai-Pagano's equations were applied for the theoretical modeling of the tensile modulus of PHBV-based composites. The heat deflection temperature (HDT) of the PHBV-based composites was increased from 105 to 131 degrees C, while the coefficient of linear thermal expansion (CLTE) value was reduced by 70% upon reinforcement with 40 wt % RCF. The PHBV-based composites had also shown better tensile and storage moduli and lower CLTE values than PP-based composites. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM) were used to study the melting behavior, thermal stability, and morphology of the composite systems, respectively.     

Engineering poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer composition in E. coli

A strain of Escherichia coli was metabolically engineered to produce poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) of specified composition between 5% and 18% HV. A gene encoding propionyl-CoA synthetase (prpE from S. enterica) was placed under the control of the IPTG-inducible tac promoter (P(taclacUV5)) while the polyhydroxyalkanoate synthesis operon (phaBCA) from R. eutropha was expressed constitutively. A strain of E. coli harboring both plasmids was grown in defined medium and PHBV was produced with specified hydroxyvalerate (HV) molar content between 5% and 18%. The molecular weight of the copolymer was approximately 700,000 across various HV contents, and average polydispersity was approximately 1.3. The majority of the PHBV production occurred during the late exponential/stationary phase. The HV content of the copolymer generally peaked early in the incubation before falling to its final value. We found that the time profiles of PrpE activity, propionyl-CoA, and acetyl-CoA were well correlated to the HV content time profile. Despite an abundance of propionyl-CoA, incorporation of HV into the copolymer was inefficient. Therefore, both the PHA operon and conditions affecting the availability of propionyl-CoA must be chosen carefully to achieve the desired HV content. The ability to engineer copolymer composition control into an E. coli strain would be useful in cases where the feedstock composition is not adjustable.     

Modification of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) film by chemical graft copolymerization

The graft copolymerization of 2-hydroxyethylmethacrylate (HEMA) onto poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBHV) films has been investigated. The graft copolymerization was conducted in aqueous media using benzoyl peroxide (BPO) as chemical initiator. PHBHV films were prepared by solvent casting. Different parameters affecting the graft yield were studied such as monomer concentration, initiator concentration, and reaction time. The extent of grafting has been modulated by the preparation conditions, in particular the concentration of HEMA. However, it is interesting to note that the initiator concentration had only a slight influence on the graft yield. Characterization of the grafted PHBHV films assumed that the graft copolymerization not only occurred on the film surface but also took place into the film bulk. Differential scanning calorimetry showed that crystallinity dramatically decreased with increasing graft yield, indicating that graft copolymerization hindered the crystallization process. Wettability has been obviously improved by grafting a hydrophilic monomer such as HEMA for high graft yield (>130%).     

n-Amyl alcohol as a substrate for the production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) by bacteria

Abstract n -Amyl alcohol was examined as a source for the synthesis of the 3-hydroxyvalerate (3HV) unit of the biopolyester, poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (P(3HB-co-3HV)), by Alcaligenes sp., Pseudomonas sp. and several methylotrophic bacteria. A. eutrophus and Ps. lemoignei synthesized P(3HB-co-3HV) from glucose and n -amyl alcohol under nitrogen-deficient conditions. Many of methylotrophic bacteria grown on methanol synthesized the copolyester from methanol and n -amyl alcohol under nitrogen-deficient conditions. The content and composition of the polyester varied from strain to strain. Paracoccus denitrificans differed from all others in having a higher content of 3-hydroxyvalerate units in the copolyester synthesized.     

Metabolic engineering of Escherichia coli for biosynthesis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from glucose

The Escherichia coli XL1-blue strain was metabolically engineered to synthesize poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] through 2-ketobutyrate, which is generated via citramalate pathway, as a precursor for propionyl-CoA. Two different metabolic pathways were examined for the synthesis of propionyl-CoA from 2-ketobutyrate. The first pathway is composed of the Dickeya dadantii 3937 2-ketobutyrate oxidase or the E. coli pyruvate oxidase mutant (PoxB L253F V380A) for the conversion of 2-ketobutyrate into propionate and the Ralstonia eutropha propionyl-CoA synthetase (PrpE) or the E. coli acetyl-CoA:acetoacetyl-CoA transferase for further conversion of propionate into propionyl-CoA. The second pathway employs pyruvate formate lyase encoded by the E. coli tdcE gene or the Clostridium difficile pflB gene for the direct conversion of 2-ketobutyrate into propionyl-CoA. As the direct conversion of 2-ketobutyrate into propionyl-CoA could not support the efficient production of P(3HB-co-3HV) from glucose, the first metabolic pathway was further examined. When the recombinant E. coli XL1-blue strain equipped with citramalate pathway expressing the E. coli poxB L253F V380A gene and R. eutropha prpE gene together with the R. eutropha PHA biosynthesis genes was cultured in a chemically defined medium containing 20 g/L of glucose as a sole carbon source, P(3HB-co-2.3 mol% 3HV) was produced up to the polymer content of 61.7 wt.%. Moreover, the 3HV monomer fraction in P(3HB-co-3HV) could be increased up to 5.5 mol% by additional deletion of the prpC and scpC genes, which are responsible for the metabolism of propionyl-CoA in host strains.     

Application of acetyl-CoA acetyltransferase (AtoAD) in Escherichia coli to increase 3-hydroxyvalerate fraction in poly(3-hydroxybutyrate-co-3-hydroxyvalerate)

Polyhydroxyalkanoate (PHA) is a family of biodegradable polymers, and incorporation of different monomers can alter its physical properties. To produce the copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (P(3HB-co-3HV)) containing a high level of 3-hydroxyvalerate (3HV) by altering acetyl-CoA pool levels, we overexpressed an acetyl-CoA acetyltransferase (atoAD) in an engineered E. coli strain, YH090, carrying PHA synthetic genes bktB, phaB, and phaC. It was found that, with introduction of atoAD and with propionate as a co-substrate, 3HV fraction in PHA was increased up to 7.3-fold higher than a strain without atoAD expressed in trans (67.9 mol%). By the analysis of CoA pool concentrations in vivo and in vitro using HPLC and LC-MS, overexpression of AtoAD was shown to decrease the amount of acetyl-CoA and increase the propionyl-CoA/acetyl-CoA ratio, ultimately resulting in an increased 3HV fraction in PHA. Finally, synthesis of P(3HB-co-3HV) containing 57.9 mol% of 3HV was achieved by fed-batch fermentation of YJ101 with propionate.

     

Biosynthesis and native granule characteristics of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in Delftia acidovorans

The ability of Delftia acidovorans to incorporate a broad range of 3-hydroxyvalerate (3HV) monomers into polyhydroxyalkanoate (PHA) copolymers was evaluated in this study. Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] containing 0–90 mol% of 3HV was obtained when a mixture of sodium 3-hydroxybutyrate and sodium valerate was used as the carbon sources. Transmission electron microscopy analysis revealed an interesting aspect of the P(3HB-co-3HV) granules containing high molar ratios of 3HV whereby, the copolymer granules were generally larger than those of poly(3-hydroxybutyrate) [P(3HB)] granules, despite having almost the same cellular PHA contents. The large number of P(3HB-co-3HV) granules occupying almost the entire cell volume did not correspond to a higher amount of polymer by weight. This indicated that the granules of P(3HB-co-3HV) contain polymer chains that are loosely packed and therefore have lower density than P(3HB) granules. It was also interesting to note that a decrease in the length of the side chain from 3HV to 4-hydroxybutyrate (4HB) corresponded to an increase in the density of the respective PHA granules. The presence of longer side chain monomers (3HV) in the PHA structure seem to exhibit steric effects that prevent the polymer chains in the granules from being closely packed. The results reported here have important implications on the maximum ability of bacterial cells to accumulate PHA containing monomers with longer side chain length.     

Production of the copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) with varied composition using different nitrogen sources with Haloferax mediterranei

The extreme haloarchaea Haloferax mediterranei accumulates poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) without the need for specific precursors. In this study, growth kinetics and PHBV synthesis were characterised under nitrogen-excess and nitrogen-limiting conditions in ammonium and, for the first time, nitrate. With excess nitrogen, ammonium and nitrate cultures generated 10.7 g/L biomass containing 4.6 wt% PHBV and 5.6 g/L biomass with 9.3 wt% PHBV, respectively. Copolymer composition varied with the nitrogen source used: PHBV from ammonium cultures had 16.9 mol% 3-hydroxyvalerate (HV), while PHBV from nitrate cultures contained 12.5 mol% HV. Nitrogen limitation was achieved with carbon-to-nitrogen (C/N) molar ratios of 25 or higher. Nitrogen limitation reduced biomass generation and polymer concentration, but polymer accumulation increased to 6.6 and 9.4% for ammonium and nitrate, respectively, with C/N 42. PHBV composition was also affected and cultures with lower C/N ratios produced richer HV polymers. Copolymer formation was not a uniform process: HV was only detected after a minimum accumulation of 0.45 g/L PHB and lasted for a maximum of 48 h. The understanding of copolymer synthesis and the influence of culture conditions such as the nitrogen source will help in designing novel strategies for the production of PHBV with more regular structure and material properties.

     

The effect of carbon source supplementation on the production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) by Cupriavidus necator

The objective of the present study was to investigate the ability of Cupriavidus necator to produce poly-(3-hydroxybutyrate-co-3-hydroxyvalerate) on various carbon sources in batch cultivation. These results show that C. necator produces poly-3-hydroxybutyrate from single carbon sources. The highest poly-3-hydroxybutyrate (P3HB) content was achieved at growth on fructose in the exponential growth phase. The maximum yield of the P3HV content was obtained when fructose was mixed with acetate. The highest content P3HB-co-3HV was also achieved by C. necator when we supplied C-excess and N- and P-normal conditions. These results indicate that C. necator accumulates high polyhydroxyalkanoates (PHA) content by depleting these elements in the culture medium. Nitrogen and phosphorus limitation has no significant effect on the PHA production, whereas C-excess leads to an increase in PHA formation of up to 92% PHAs of cell dry weight after growth on 5 g/L acetate and 40 g/L fructose.     

Biosynthesis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from glucose with elevated 3-hydroxyvalerate fraction via combined citramalate and threonine pathway in Escherichia coli

The biosynthesis of polyhydroxyalkanoate copolymers in Escherichia coli from unrelated carbon sources becomes attractive nowadays. We previously developed a poly(hydroxybutyrate-co-hydroxyvalerte) (PHBV) biosynthetic pathway from an unrelated carbon source via threonine metabolic route in E. coli (Chen et al., Appl Environ Microbiol 77:4886-4893, 2011). In our study, a citramalate pathway was introduced in recombinant E. coli by cloning a cimA gene from Leptospira interrogans. By blocking the pyruvate and the propionyl-CoA catabolism and replacing the β-ketothiolase gene, the PHBV with 11.5 mol% 3HV fraction was synthesized. Further, the combination of citramalate pathway with the threonine biosynthesis pathway improved the 3HV fraction in PHBV copolymer to 25.4 mol% in recombinant E. coli.     

Nanofibrous poly(3-hydroxybutyrate-co-3-hydroxyvalerate)/chitosan scaffolds for skin regeneration

The purpose of this study was to evaluate hybrid poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV)/chitosan nanofibrous mats as scaffolds for skin engineering. In vitro studies were carried out to test the potential of the scaffolds for fibroblasts adhesion, viability, and proliferation (L929 cell line). The in vivo performance was also studied in a full-thickness wound healing model. PHBV/chitosan 4:1 (w/w) exhibited a higher in vitro biocompatibility and a better ability for cell adhesion and growth, compared to PHBV/chitosan 2:3 (w/w). The in vivo assay also revealed the better performance of this scaffold, improving the wound healing process in rats.