The relationship between surface tension and the industrial performance of water-soluble polymers prepared from acid hydrolysis lignin, a saccharification by-product from woody materials

In this study, water-soluble anionic and cationic polymers were prepared from sulfuric acid lignin (SAL), an acid hydrolysis lignin, and the relationship between the surface tension of these polymers and industrial performance was examined. The SAL was phenolized (P-SAL) to enhance its solubility and reactivity. Sulfonation and the Mannich reaction with aminocarboxylic acids produced water-soluble anionic polymers and high-dispersibility gypsum paste. The dispersing efficiency increased as the surface tension decreased, suggesting that the fluidity of the gypsum paste increased with the polymer adsorption on the gypsum particle surface. Water-soluble cationic polymers were prepared using the Mannich reaction with dimethylamine. The cationic polymers showed high sizing efficiency under neutral papermaking conditions; the sizing efficiency increased with the surface tension. This suggests that the polymer with high hydrophilicity spread in the water and readily adhered to the pulp surface and the rosin, showing good retention.     

绿色木霉粗纤维素酶液水解壳聚糖的研究

利用自制绿色木霉粗纤维素酶液降解壳聚糖制备低聚壳聚糖.采用粘度法、乙酰丙酮法和还原糖浓度分析,研究了温度、pH值及反应时间等因素对壳聚糖水解程度和产物相对分子质量的影响,并采用质谱法对水解产物进行定性分析.结果表明,粗纤维素酶液水解壳聚糖作用的最适pH为5.0、最适反应温度为50 ℃、最适反应时间为12 h.粗纤维素酶...     

An extreme halophilic enzyme active at low salt in reversed micelles.

Possible biotechnological applications of extreme halophilic enzymes are strongly determined by their high salt requirement of around 4 M NaCl. Consequently, the use of these in organic media seemed to be unlikely. However, we have succeeded in dissolving a halophilic enzyme, p-nitrophenylphosphate phosphatase from the archaeon Halobacterium salinarum, in an organic medium by creating a reverse micellar system with very low salt concentration. The enzyme retained its catalytic properties in reversed micelles made with an anionic surfactant (dioctyl sodium sulphosuccinate) or with a cationic surfactant (hexadecyltrimethylammonium bromide) in cyclohexane plus 1-butanol as co-surfactant. The dependence of the rate of hydrolysis of p-nitrophenylphosphate phosphate on the molar water/surfactant ratio (w(0) value) showed a bell-shaped curve for each surfactant system. Kinetic parameters were determined in each system. The enzymatic reaction appeared to follow Michaelis-Menten kinetics with the anionic surfactant only. The kinetic behaviour was determined at different concentrations of Mn(2+) in reversed micelles of dioctyl sodium sulphosuccinate as surfactant.     

Enhancement of enzymatic hydrolysis of cellulose by surfactant

Effects of surfactants on enzymatic saccharification of cellulose have been studied. Nonionic, amphoteric, and cationic surfactants enhanced the saccharification, while anionic surfactant did not. Cationic and anionic surfactants denatured cellulase in their relatively low concentrations, namely, more than 0.008 and 0.001%, respectively. Using nonionic surfactant Tween 20, which is most effective to the enhancement (e.g., the fractional conversion attained by 72 h saccharification of 5 wt % Avicel in the presence of 0.05 wt % Tween 20 is increased by 35%), actions of surfactant have been examined. As the results, it was suggested that Tween 20 plays an important role in the hydrolysis of crystalline cellulose and that Tween 20 disturbs the adsorption of endoglucanase on cellulose, i.e., varies the adsorption balance of endo- and exoglucanase, resulting in enhancing the reaction. The influence of Tween 20 to the saccharification was found to remain in simultaneous saccharification and fermentation of Avicel.     

BIOLOGICAL EFFECTS OF SURFACTANTS. V. GROWTH AND ANTHOCYANIN PRODUCTION BY CALLUS CULTURES OF DIMORPHOTHECA

Effects of five homologous series of amphoteric, anionic, and nonionic surfactants on growth and anthocyanin production by callus cultures of Dimorphotheca sinuata were examined. The phytotoxicity of amphoteric sulfobetaines increased with alkyl chain length and reached a plateau at 14 to 16 carbon atoms. In the case of the anionic sodium alkyl sulfates, the dodecyl derivative caused the greatest inhibition. Higher molecular weight ionic detergents were less toxic, probably due to their high Krafft temperatures and concomitant reduced solubility. The nonionic higher alcohol ethoxylates were generally less inhibitory than the ionic detergents and had little or no effect below their critical micelle concentrations. Fresh weights of tissues and anthocyanin production by Dimorphotheca callus cultures declined with increasing surfactant concentrations.     

A new amphoteric superabsorbent hydrogel based on sodium starch sulfate

A new amphoteric superabsorbent hydrogels were synthesized by graft copolymerization blending based on acrylamide (AM), diallydimethylammonium chloride (DMDAAC) and sodium starch sulfate (SSS). The effect of polymerization conditions on swelling capacity was investigated. The results showed that the swelling capacity was affected by various factors, such as polymerization temperature, concentration of initiator and crosslinker, and dose of AM. Additionally, the results testified that salt bond was a potential crosslinking factor in the amphoteric hydrogel. The maximum swelling capacity in distilled water and saline solution reached 1493.1 and 91.0 g/g, respectively. These results were compared with those obtained from original starch-based hydrogel.     

Peroxyoxalate chemiluminescence enhanced by oligophenylenevinylene fluorophores in the presence of various surfactants

The effect of several surfactants on peroxyoxalate chemiluminescence (PO‐CL) using oligophenylenevinylene fluorophores was investigated. Among several oligophenylenevinylenes consisting of stilbene units, linearly conjugated ones, such as distyrylbenzene and distyrylstilbene, effectively enhanced PO‐CL efficiency. Various effects of anionic, cationic, amphoteric and non‐ionic surfactants on the CL efficiency of PO‐CL were determined using three oxalates and the distyrylbenzene fluorophore. Anionic and non‐ionic surfactants effectively enhanced CL efficiency, in contrast to the negative effect of cationic and amphoteric surfactants. Non‐ionic surfactants were also effective in CL reactions of oxalates bearing dodecyl ester groups by the hydrophobic interaction between their alkyl chains. Considering these results, the surfactants not only increase the concentrations of water‐insoluble interacting species in the hydrophobic micelle cores, but also control rapid degradation of the oxalates by alkaline hydrolysis. Copyright © 2014 John Wiley & Sons, Ltd.     

Impact of Polyacrylamide Treatment on Sorptive Dynamics and Degradation of 2,4-D and Atrazine in Agricultural Soil

High-molecular-weight, anionic polyacrylamide (PAM) is added to irrigation water to reduce soil erosion during furrow irrigation of crops. The chemical nature of PAM, together with the observation that the polymer can be biotransformed by soil bacteria, led us to question the impact of PAM treatment on the fate of coapplied agrochemicals. The herbicides, atrazine (nonionic) and 2,4-D (anionic), were tested for pesticide sorption, desorption, and degradation in PAM-treated and untreated soils. Sorption of atrazine and 2,4-D in soil was unaffected by PAMtreatment, as was atrazine desorption. However, 2,4-D desorbedmore readily from the PAM-treated soil than from untreated soil. With respect to pesticide degradation, mineralization of the 2,4-D aromatic ring was not impacted by PAM treatment, but decarboxylation of the 2,4-D carboxylic acid side chain was significantly reduced in the PAM-treated soil. Limited mineralization (7 to 10%) of atrazine was observed in both soils. However, in PAM-treated soils atrazine conversion to ¹⁴CO₂ and bound residue components was significantly reduced, and there was an increase in the level of methanol extractable metabolites. These results may indicate that PAM application can alter the environmental fate of some pesticides in soils, especially under the high dose treatment conditions examined in this study.     

角蛋白/海藻酸钠/聚丙烯酰胺水凝胶皮肤敷料的制备及创口修复研究

为了获得更为理想的皮肤创口修复敷料,在海藻酸钠(SA)和聚丙烯酰胺(PAM)水凝胶的基础上复合人发角蛋白(KTN),制得KTN/SA/PAM水凝胶皮肤敷料.用电子万能测试机、扫描电子显微镜等对其进行表征,结果显示,KTN/SA/PAM水凝胶皮肤敷料拉伸强度为42.41 kPa,弹性模量11.19 kPa,接近人体皮肤组...     

Effect of phospholipase D on micellar phospholipids and the role of calcium ions]

The rates of the reaction products formation under simultaneous phospholipase D effect on phosphatidyl ethanolamine and phosphatidyl choline were studied. The hydrolysis of cephalin, unlike the phospholipase D effect on lecithin, does not require Ca2+ ions. Ca2+ does not affect the enzymatic degradation of lecithin and inhibits the reaction with cephalin in "inorganized" phospholipid emulsions. The hydrolysis of micellar phospholipids by phospholipase D (in the presence of the anionic detergent sodium dodecyl sulfate) is accelerated by Ca2+ ions for both substrates. The apparent Km value is equal to 1.5 mM and does not depend on the phospholipid type. In contrast, the value of kcat for lecithin is twice as high as that for cephalin. It was demonstrated that the phase state of the phospholipids and the chemical nature of the alcohol residue in the phospholipid molecule are essential for the substrate specificity of phospholipase D.     

Preparation of poly(L-lactide)-based microspheres having a cationic or anionic surface using biodegradable surfactants

Poly(L-lactide)-based microspheres having cationic or anionic surfaces were prepared using polydepsipeptide-block-poly(L-lactide)s as surfactants. Polydepsipeptide-block-poly(L-lactide)s having amino or carboxylic acid groups on their side chains were synthesized through anionic ring-opening polymerizations of L-lactide using the corresponding protected polydepsipeptides as macroinitiators and consequent deprotections. Since these amphiphilic copolymers consisting of hydrophobic segments and hydrophilic segments with amino or carboxylic acid groups could be converted to cationic or anionic block copolymers, they could act as surfactants preparing poly(L-lactide)-based microspheres by an oil-in-water emulsion method. The amount of ionic groups located on the surfaces of the obtained microspheres was found to increase with increasing the feed of charged polydepsipeptide-block-poly(L-lactide)s in the blend of poly(L-lactide) and block copolymers. The average diameters of the dried microspheres estimated by scanning electron microscopy were found to decrease with an increase in feed of block copolymers in polymer blends.     

Preparation and structural characterisation of O-aminopropyl starch and amylose

O-aminopropyl starch was prepared by Michael addition of acrylonitrile and subsequent reduction with freshly prepared cobalt boride and sodium borohydride. In a second approach, the aminopropyl group was introduced via Williamson etherification with N-phthalyl-protected 3-bromo-1-propylamine. The protecting group was removed by borohydride reduction and subsequent hydrolysis in acetic acid. The DS of all samples and the degree of reduction of the cyanoethyl groups were estimated from the 1H NMR spectra. Total monomer composition was determined after methanolysis or hydrolysis and trimethylsilylation by GLC and GCMS. While the regioselectivity in the thermodynamically controlled reaction was O-6 > O-2 > O-3 (50:37:13), the kinetically controlled process showed strongly preferred O-2-etherification (up to 94%) followed by O-6- and O-3-substitution. It could be influenced by choice of solvent (water, Me(2)SO) and base (NaOH, Li-dimsyl).     

Inhibition of lipases by epsilon-polylysine

Oral administration of epsilon-polylysine to rats reduced the peak plasma triacylglycerol concentration. In vitro, epsilon-polylysine and polylysine strongly inhibited the hydrolysis, by either pancreatic lipase or carboxylester lipase, of trioleoylglycerol (TO) emulsified with phosphatidylcholine (PC) and taurocholate. The epsilon-polylysine concentration required for complete inhibition of pancreatic lipase, 10 microg/ml, is 1,000 times lower than that of BSA required for the same effect. Inhibition requires the presence of bile salt and, unlike inhibition of lipase by other proteins, is not reversed by supramicellar concentrations of bile salt. Inhibition increases with the degree of polylysine polymerization, is independent of lipase concentration, is independent of pH between 5.0 and 9.5, and is accompanied by an inhibition of lipase binding to TO-PC emulsion particles. However, epsilon-polylysine did not inhibit the hydrolysis by pancreatic lipase of TO emulsions prepared using anionic surfactants, TO hydrolysis catalyzed by lingual lipase, or the hydrolysis of a water-soluble substrate. In the presence of taurocholate, epsilon-polylysine becomes surface active and adsorbs to TO-PC monomolecular films. These results are consistent with epsilon-polylysine and taurocholate forming a surface-active complex that binds to emulsion particles, thereby retarding lipase adsorption and triacylglycerol hydrolysis both in vivo and in vitro.     

Feasibility study of the anaerobic digestion of dewatered pig slurry by means of polyacrylamide

Liquid livestock waste can be managed by separating liquid and solid fractions then treating each separately by applying best available technology, such as anaerobic digestion for the solid fraction. There is an increasing use of polyacrylamide (PAM) as a flocculant agent to improve solid-liquid separation. In the present work, the anaerobic toxicity of PAM residues and the optimal range of total solids concentration for maximum methane production were studied as a function of PAM dosage. Results showed that dry matter and its volatile solids content increased significantly with increasing PAM dosage. Batch anaerobic tests showed that methane yield decreased linearly with increasing total solids, while the methane production per unit of raw substrate reached a maximum at 16.4% total solids. No PAM toxicity was measured for PAM concentrations below 415 g/kg total solids, but some indirect inhibitory phenomena were observed, such as a limited hydrolysis rate due to particle aggregation, and inhibition of methanogenesis by high ammonia concentration.     

Preparation and Thermal Energy Storage of Carboxymethyl Cellulose-Modified Nanocapsules

A series of nanocapsules with carboxymethyl cellulose (CMC)-modified melamine-formaldehyde as the shell material and phase change paraffin as the core material were prepared by in situ polymerization. The modified capsules were examined using Fourier transform infrared spectra, scanning electronic microscope, differential scanning calorimeter, and optical microscopy, and two factors that influence paraffin emulsion preparation (emulsifier type and stirring rate) were investigated. The effects of the synthesis conditions used for the prepolymer on the surface morphology of the capsules were also studied. We found that phase change capsules prepared with both anionic and nonionic emulsifiers were superior to those prepared with a simple emulsifier. The best performance of the paraffin emulsion was obtained when the emulsion was stirred at 8,000 rpm during preparation. The optimal prepolymer reaction conditions to give smooth capsules with good dispersibility and complete morphology were reaction temperature 72.5 °C, reaction time 75 min, and pH?8.5. The CMC-modified nanocapsules have a phase change enthalpy of 83.46 J/g, are fully encased, and are uniform, with an average particle size of 50 nm.     

Neutralization of the activity of eight disinfectants by organic matter

The effect of organic matter on the activity of eight disinfectants was evaluated. Three types of interfering substrates (whole milk powder, dried beef blood and fish meal) were tested according to the method of Whitmore and Miner adapted to the AOAC use-dilution method. Glutaraldehyde and to a certain extent, chlorhexidine acetate and the amphoteric surfactant kept their disinfecting activity after contact with high concentrations of organic matter. The quaternary ammonium compound as well as the quaternary ammonium-glutaraldehyde complex were more readily neutralized whereas anionic acid, iodophor and sodium hypochlorite did not tolerate the presence of organic matter. The neutralizing activity of powders was correlated to their solubility and composition.     

A method for the use of Zenker-formol fixation and the periodic acid Schiff staining technique in light microscopic radioautography

Summary Although providing superior histological preservation, Zenker-formol fixation has not been utilized in radioautographic experiments, since some component of the fixative (presumably mercury) desensitizes the emulsion and thus prevents the appearance of a radioautographic reaction. Attempts to identify and eliminate the effects of this desensitizing agent led to experiments with Zenker-formol fixed tissues from rats injected with ³H-leucine or ³H-thymidine. Radioautographs of such tissues contained a brown-black precipitate and occasionally a heavy background fog, but no normal radioautographic reaction. Moreover, when the radioautographs were exposed to light, the emulsion was transparent over the tissues, indicating that a tissue-bound component had completely desensitized the emulsion. The two components of Zenker's fluid-mercuric chloride and potassium dichromate-plus the mercurous chloride which forms as a precipitate in the course of fixation, were then tested for their individual effects on the radioautographic emulsion. It was found that mercuric chloride was primarily responsible for the desensitization of the emulsion. Merourous chloride, which formed the dark precipitate in radioautographs, produced the background fog. While potassium dichromate caused some desensitization of the emulsion, in normal histological processing where tissues had a lengthy post-fixation wash, this substance was for the most part washed out.A number of attempts were made to remove the mercury by treating the Zenker-fixed tissues with solutions of iodine, sodium thiosulfate and cysteine. It was found that the most intense radioautographic reaction was obtained with the following procedure: prior to embedding, tissue blocks were treated with 0.5% iodine solution in 70% alcohol for 17 hours. Optionally, sections of this material could be given a second treatment with 0.5% alcoholic iodine for 10 minutes. Although simple iodination eliminated the mercurous chloride precipitate and the background fog, there was still no radioautographic reaction. However, subsequent treatment of sections of this iodinated material in 5% aqueous sodium thiosulfate for 5 minutes yielded an adequate radioautographic reaction. Therefore, the simultaneous removal of both mercurous chloride precipitate and tissue bound mercury required iodination followed by sodium thiosulfate. Using this procedure, a method was described for preparing tissues for radioautography using Zenker-formol fixation and the periodic acid-Schiff staining technique.This work was supported by a grant from the Medical Research Council of Canada to Dr. C. P. Leblond.     

Influence of Ionic Surfactants on the Microstructure of Heat-Set β-Lactoglobulin-Stabilized Emulsion Gels

Using confocal microscopy, we studied the effect of heating (up to 85°C) on the microstructure of β-lactoglobulin-stabilized emulsions (20 vol% oil, pH 6.8) containing excess protein (total protein content 13.2%). Two different fluorescent dyes were used to separately visualize the oil droplets and the protein. In overlay micrographs, their location with respect to each other could then be determined. In the presence of a low salt concentration, flocculation of the emulsion without surfactant was inhibited, by a mechanism analogous to the “salting-in” of aqueous protein solutions. Addition of the anionic surfactant sodium dodecyl sulfate (SDS) caused weak flocculation, probably as a result of the formation of protein−SDS complexes. The final heat-set emulsion contained distinct pores for a surfactant/protein ratio of R = 1, but no pores for R = 2. Addition of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB) caused strong aggregation, as indicated by microscopic observation of the concentrated emulsion and light scattering of the diluted emulsion. For R = 1 with CTAB, there were aggregates consisting of oil droplets and excess protein. At R = 2, almost all the excess protein was aggregated into separate protein flakes. In the final emulsion gels containing CTAB, the protein was more spread out. Differing structural behavior with anionic and cationic surfactants has been interpreted in terms of different protein−surfactant interactions in aqueous solution and at the oil−water interface, both before and after protein denaturation.     

Human glutathione S-transferases. Characterization of the anionic forms from lung and placenta.

Anionic glutathione S-transferases were purified from human lung and placenta. Chemical and immunochemical characterization, including polyacrylamide-gel electrophoresis, gave strong evidence that the anionic lung and placental enzymes are chemically similar, if not identical, proteins. The electrophoretic mobilities of both proteins were identical in conventional alkaline gels as well as in gels containing sodium dodecyl sulphate. Gel filtration of the intact active enzyme established an Mr value of 45000; however, with sodium dodecyl sulphate/polyacrylamide-gel electrophoresis under dissociating conditions a subunit Mr of 22500 was obtained. Amino acid sequence analysis of the N-terminal region of the placental enzyme revealed a single polypeptide sequence identical with that of lung. Results obtained from immunoelectrophoresis, immunotitration, double immunodiffusion and rocket immunoelectrophoresis also indicated the anionic lung and placental enzymes to be closely similar. The chemical similarity of these two proteins was further supported by protein compositional analysis and fragment analysis after chemical hydrolysis. Immunochemical comparison of the anionic lung and placental enzymes with human liver glutathione S-transferases revealed cross-reactivity with the anionic omega enzyme, but no cross-reactivity was detectable with the cationic enzymes. Comparison of the N-terminal region of the human anionic enzyme with reported sequences of rat liver glutathione S-transferases gave strong evidence of chemical similarity, indicating that these enzymes are evolutionarily related. However, computer analysis of the 30-residue N-terminal sequence did not show any significant chemical similarity to any other reported protein sequence, pointing to the fact that the glutathione S-transferases represent a unique class of proteins.     

Emulsion formed in bovine serum album/anionic surfactant/H2O system under acidic condition

At neutral pH, bovine serum album (BSA) conformation is "heart-shaped", and with decreasing pH, BSA may adopt the fast "F" form below a pH of about 4, and expanded "E" form at pH lower than about 3. However, as far as we know, the researches on the interaction between protein and surfactant are all carried out at pH higher than its isoelectric point (pI, which is 4.9), which means only the information about how the "heart-shaped" BSA interacts with surfactant is understood so far. In this paper, we studied the interaction between BSA and anionic surfactant at pH lower than its pI and hope to help understand the role of protein conformation in its interaction with surfactant. We found that BSA and anionic surfactant could form emulsion only when pH value was lower than or about 3, suggesting that the "E" formed BSA was an important criterion for emulsion formation. Moreover, the emulsion formation was companied with increased α-helix content and decreased β-sheet content for BSA. In addition, the emulsion formation was closely dependent on the anionic surfactant content; only a moderate anionic surfactant could make emulsion formed.