Energy requirements and process design considerations in compression-milling pretreatment of cellulosic wastes for enzymatic hydrolysis

The effectiveness of compression-milling pretreatment of lignocellulosics for enzymatic hydrolysis has been demonstrated for a wide variety of substrate sources. Reductions in the degree of crystallinity and the degree of polymerization of cellulose and partial destruction of the structural integrity of lignocellulosics brought about by compression milling significantly increase the susceptibility of cellulose to enzymatic hydrolysis. The enzymatic hydrolysis yield was found to be directly related to the specific energy input to the cellulosic substrate (kWh/1b substrate) by compression milling, and the energy input can be controlled by the milling time. The enzymatic hydrolysis yeilds from cellulosic materials pretreated by compression milling also vary significantly depending on the source and kind, the composition milling also vary significantly depending on the source and kind, the composition (contents of lignin and other components), and the structure. The power requirements for compression milling which renders equivalent hydrolysis yields also depend on the source and kind of lignocellulosics to be pretreated. For newspaper, the specific energy input required for 55% sugar yield is estimated as 0.3 kWh/lb substrate including 15% power loss. The additional sugar yield gained from the enzymatic hydrolysis of compression-milled newspaper (over and above the sugar yield of untreated substrate) is determined as 453 g sugar/kWh energy input.     

Differential speed two roll mill pretreatment of cellulosic materials for enzymatic hydrolysis

Differential speed two roll milling is an effective pretreatment for increasing the susceptibility of cellulose to enzymatic hydrolysis. Using mills with three, six, and ten in. diam rolls and processing times of 10 min or less results in the following percent increases in susceptibility over untreated controls: cotton, 1100; maple chips, 1600; white pine chips, 600; newspaper, 125. In comparison, ball milling of newspaper for 24 hr gives only a 62% increase. A further advantage of the roll mill is the increased wet density of the product permitting higher slurry concentrations during hydrolysis. Important parameters of mill effectiveness are roll clearance and processing time.     

斑茅酶解转化可发酵单糖的液氨预处理及参数优化

斑茅(Saccharum arundinaceum Retz.)的生物产量高,对土壤条件要求低,可作为纤维素乙醇生产的原料作物在我国南方地区广泛种植.实验以斑茅为原料,采用液氨预处理法克服其水解顽抗性,并添加纤维素酶进行酶解,运用高效液相色谱(HPLC)测定了酶解液中的单糖含量.实验结果表明在纤维素酶添加量为15FPU/(g当量葡聚糖)、预处理原料含水率为80％、预处理温度为130℃、预处理驻留时间为10 min、液氨与生物质的质量比例为2∶1时,葡聚糖和木聚糖的总转化率分别为69.34％和82.60％,相比于未作预处理的原料分别提高了573％和1 056％,单糖产量提高8倍.实验结果表明液氨预处理对斑茅是一种有效的预处理方式,并优于稀酸或湿爆法预处理,与酸预处理和氨爆法(AFEX)处理效果接近.     

Ethanol production from non-starch carbohydrates of wheat bran

Wheat bran (WB), produced worldwide in large quantities as a by-product of the wheat milling industry, constitutes a significant underutilized source of sugars. This paper describes various methods of hydrolyzing the abundant polysaccharides in bran to yield a sugar feedstock suitable for fermentation into bioethanol. Firstly, the starch in the bran was released using amylolytic enzymes. The fibrous material remaining was further hydrolyzed. Acid hydrolysis, heat pretreatment followed by enzymatic hydrolysis and direct enzymatic hydrolysis were compared in terms of total sugar yield and pentose sugar yield. The maximum total sugar yield was achieved when small amounts of acid were added at the pretreatment step prior to enzymatic hydrolysis. This form of pretreatment released most pentosans and significantly enhanced the hydrolysis of cellulose. The overall sugar yield of this combined hydrolysis method reached 80% of the theoretical and it consisted of 13.5 g arabinose, 22.8 g xylose and 16.7 g glucose per 100 g starch-free bran.     

Supercritical CO2 pretreatment of lignocellulose enhances enzymatic cellulose hydrolysis

The supercritical carbon dioxide (SC-CO2) pretreatment of lignocellulose for enzymatic hydrolysis of cellulose was investigated. Aspen (hardwood) and southern yellow pine (softwood) with moisture contents in the range of 0-73% (w/w) were pretreated with SC-CO2 at 3100 and 4000 psi and at 112-165 degrees C for 10-60 min. Each pretreated lignocellulose was hydrolyzed with commercial cellulase to assess its enzymatic digestibility. Untreated aspen and southern yellow pine (SYP) gave final reducing sugar yields of 14.5 +/- 2.3 and 12.8 +/- 2.7% of theoretical maximum, respectively. When no moisture was present in lignocellulose to be pretreated, the final reducing sugar yield from hydrolysis of SC-CO2-pretreated lignocellulose was similar to that of untreated aspen. When the moisture content of lignocellulose was increased, particularly in aspen, significantly increased final sugar yields were obtained from enzymatic hydrolysis of SC-CO2-pretreated lignocellulose. When the moisture content of lignocellulose was 73% (w/w) before pretreatment, the sugar yields from the enzymatic hydrolysis of aspen and southern yellow pine pretreated with SC-CO2 at 3100 psi and 165 degrees C for 30 min were 84.7 +/- 2.6 and 27.3 +/- 3.8% of theoretical maximum, respectively. The SC-CO2 pretreatments of both aspen and SYP with moisture contents of 40, 57, and 73% (w/w) showed significantly higher final sugar yields compared to the thermal pretreatments without SC-CO2.     

Optimization of ammonia fiber expansion (AFEX) pretreatment and enzymatic hydrolysis of Miscanthus x giganteus to fermentable sugars

Miscanthus x giganteus is a tall perennial grass whose suitability as an energy crop is presently being appraised. There is very little information on the effect of pretreatment and enzymatic saccharification of Miscanthus to produce fermentable sugars. This paper reports sugar yields during enzymatic hydrolysis from ammonia fiber expansion (AFEX) pretreated Miscanthus. Pretreatment conditions including temperature, moisture, ammonia loading, residence time, and enzyme loadings are varied to maximize hydrolysis yields. In addition, further treatments such as soaking the biomass prior to AFEX as well as washing the pretreated material were also attempted to improve sugar yields. The optimal AFEX conditions determined were 160 degrees C, 2:1 (w/w) ammonia to biomass loading, 233% moisture (dry weight basis), and 5 min reaction time for water-soaked Miscanthus. Approximately 96% glucan and 81% xylan conversions were achieved after 168 h enzymatic hydrolysis at 1% glucan loading using 15 FPU/(g of glucan) of cellulase and 64 p-NPGU/(g of glucan) of beta-glucosidase along with xylanase and tween-80 supplementation. A mass balance for the AFEX pretreatment and enzymatic hydrolysis process is presented.     

Wet disk milling pretreatment without sulfuric acid for enzymatic hydrolysis of rice straw

Rice straw has recently attracted interest in Japan as a potential source of raw material for ethanol production. Wet disk milling, a continuous pretreatment to enhance the enzymatic digestibility of rice straw, was compared with conventional ball milling and hot-compressed water treatment. Pretreated rice straw was evaluated by enzymatic hydrolysis using Acremonium cellulase and characterized by X-ray diffraction and scanning electron microscopy. Glucose and xylose yields by wet disk milling, ball milling, and hot-compressed water treatment were 78.5% and 41.5%, 89.4% and 54.3%, and 70.3% and 88.6%, respectively. Wet disk milling and hot-compressed water treatment increased sugar yields without decreasing their crystallinity. The feature size of the wet disk milled rice straw was similar to that of hot-compressed water-treated rice straw. The energy consumption of wet disk milling was lower than that of other pretreatments. Thus, wet disk milling is an economical, practical pretreatment for the enzymatic hydrolysis of lignocellulosic biomass, especially herbaceous biomass such as rice straw.     

The effects of nonionic surfactants on the pretreatment and enzymatic hydrolysis of recycled newspaper

The effects of surfactants on the pretreatment and enzymatic hydrolysis stages of recycled newspaper processing were examined. Newspaper substrate was pretreated with surfactants at 40°C and 400 rpm for 1 h, and the enzymatic digestibilities of the pretreated substrate were compared. NP-20 was 10–20% more effective as a surfactant than Tween-20 and Tween-80. To investigate the effects of the surfactants on the subsequent enzymatic hydrolysis stage, the newspaper was pretreated with NP-20 and then hydrolyzed in the presence of TW-20 or TW-80. TW-80 showed an approximate 7% higher digestibility than TW-20. The surfactant effect on the hydrolysis of the untreated newspaper was significant, whereas the surfactant effect on the hydrolysis of the surfactant-pretreated newspaper was marginal. When the digestibilities of the pure cellulose substrates (α-cellulose and filter paper) were examined, markedly different surfactant effects were observed. In contrast to the newspaper substrate, the surfactant-pretreated pure cellulose substrates had a significant effect on digestibility when they were hydrolyzed in the presence of a surfactant, indicating that the surfactant effect on digestibility is highly dependent on substrate type.     

Effect of initial moisture content and chip size on the bioconversion efficiency of softwood lignocellulosics

Previous optimization strategies for the bioconversion of lignocellulosics by steam explosion technologies have focused on the effects of temperature, pH, and treatment time, but have not accounted for changes in severity brought about by properties inherent in the starting feedstock. Consequently, this study evaluated the effects of chip properties, feedstock size (40-mesh, 1.5 x 1.5 cm, 5 x 5 cm), and moisture content (12% and 30%) on the overall bioconversion process, and more specifically on the efficacy of removal of recalcitrant lignin from the lignocellulosic substrates following steam explosion. Increasing chip size resulted in an improvement in the solids recovery, with concurrent increases in the water soluble, hemicellulose-derived sugar recovery (7.5%). This increased recovery is a result of a decrease in the "relative severity" of the pretreatment as chip size increases. Additionally, the decreased relative severity minimized the condensation of the recalcitrant residual lignin and therefore increased the efficacy of peroxide fractionation, where a 60% improvement in lignin removal was possible with chips of larger initial size. Similarly, increased initial moisture content reduced the relative severity of the pretreatment, generating improved solids and hemicellulose-derived carbohydrate recovery. Both increased chip size and higher initial moisture content results in a substrate that performs better during peroxide delignification, and consequently enzymatic hydrolysis. Furthermore, a post steam-explosion refining step increased hemicellulose-derived sugar recovery and was most effectively delignified (to as low as 6.5%). The refined substrate could be enzymatically hydrolyzed to very high levels (98%) and relatively fast rates (1.23 g/L/h).     

Enhanced enzymatic hydrolysis of rapeseed straw by popping pretreatment for bioethanol production

The objective of this study was to find a pretreatment process that enhances enzymatic conversion of biomass to sugars. Rapeseed straw was pretreated by two processes: a wet process involving wet milling plus a popping treatment, and a dry process involving popping plus dry milling. The effects of the pretreatments were studied both in terms of structural and compositional changes and change in susceptibility to enzymatic hydrolysis. After application of the wet and dry processes, the amounts of cellulose and xylose in the straw were 37-38% and 14-15%, respectively, compared to 31% and 12% in untreated counterparts. In enzymatic hydrolysis performance, the wet process presented the best glucose yield, with a 93.1% conversion, while the dry process yielded 69.6%, and the un-pretreated process yielded <20%. Electron microscopic studies of the straw also showed a relative increase in susceptibility to enzymatic hydrolysis with pretreatment.     

Thermo-mechanical extrusion pretreatment for conversion of soybean hulls to fermentable sugars

Thermo-mechanical extrusion pretreatment for lignocellulosic biomass was investigated using soybean hulls as the substrate. The enzyme cocktail used to hydrolyze pretreated soybean hulls to fermentable sugars was optimized using response surface methodology (RSM). Structural changes in substrate and sugar yields from thermo-mechanical processing were compared with two traditional pretreatment methods that utilized dilute acid (1% sulfuric acid) and alkali (1% sodium hydroxide). Extrusion processing parameters (barrel temperature, in-barrel moisture, screw speed) and processing aids (starch, ethylene glycol) were studied with respect to reducing sugar and glucose yields. The conditions resulting in the highest cellulose to glucose conversion (95%) were screw speed 350 rpm, maximum barrel temperature 80 °C and in-barrel moisture content 40% wb. Compared with untreated soybean hulls, glucose yield from enzymatic hydrolysis of soybean hulls increased by 69.6%, 128.7% and 132.2%, respectively, when pretreated with dilute acid, alkali and extrusion.     

青贮对柳枝稷制取燃料乙醇转化过程的影响

青贮是一种传统的生物质原料保存方法,广泛应用于纤维素乙醇炼制领域尚需要考察其对原料品质和下游乙醇转化过程的影响。文中以秋季(初、中和末)收割的柳枝稷为原料,通过青贮、高温水热(LHW)预处理、纤维素酶水解和同步糖化与发酵(SSF)实验对上述问题予以回答。结果显示,秋季初收割的柳枝稷以不同湿度青贮后pH均小于4.0,干重损失小于2%,各主要成分与青贮前相比无明显变化;LHW预处理中青贮样品半纤维素水解率普遍高于未贮存样品,但青贮同样使原料获得了更高的发酵抑制物产生水平;青贮柳枝稷葡萄糖、木糖和半乳糖产量(预处理+酶水解)高于未贮存柳枝稷;经过168 h的SSF,青贮样品乙醇浓度为12.1 g/L,未贮存的秋季初、秋季中和秋季末柳枝稷为底物的浓度分别为10.3 g/L、9.7 g/L和10.6 g/L。综上,青贮有助于提高柳枝稷LHW预处理效率、酶水解率和乙醇产量。     

Efficient Acetone–Butanol–Ethanol Production from Corncob with a New Pretreatment Technology—Wet Disk Milling

Acetone–butanol–ethanol (ABE) production from corncob was achieved using an integrated process combining wet disk milling (WDM) pretreatment with enzymatic hydrolysis and fermentation by Clostridium acetobutylicum SE-1. Sugar yields of 71.3 % for glucose and 39.1 % for xylose from pretreated corncob were observed after enzymatic hydrolysis. The relationship between sugar yields and particle size of the pretreated corncob was investigated, suggesting a smaller particle size benefits enzymatic hydrolysis with the WDM pretreatment approach. Analysis of the correlation between parameters representing particle size and efficiency of enzymatic hydrolysis predicted that frequency 90 % is the best parameter representing particle size for the indication of the readiness of the material for enzymatic hydrolysis. ABE production from corncob was carried out with both separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) processes using C. acetobutylicum SE-1. Interestingly, when considering the time for fermentation as the time for ABE production, a comparable rate of sugar consumption and ABE production in the SHF process (0.55 g/l·h sugar consumption and 0.20 g/l·h ABE production) could be observed when glucose (0.50 g/l·h sugar consumption and 0.17 g/l·h ABE production) or a mixture of glucose and xylose (0.68 g/l·h sugar consumption and 0.22 g/l·h ABE production) mimicking the corncob hydrolysate was used as the substrate for fermentation. This result suggested that the WDM is a suitable pretreatment method for ABE production from corncob owing to the mild conditions. A higher ABE production rate could be observed with the SSF process (0.15 g/l·h) comparing with SHF process (0.12 g/l·h) when combining the time for saccharification and fermentation and consider it as the time for ABE production. This is possibly a result of low sustained sugar level during fermentation. These investigations lead to the suggestion that this new WDM pretreatment method has the potentials to be exploited for efficient ABE production from corncob.     

Enriched arabinoxylan in corn fiber for value-added products

A two-step process is evaluated to separate the hexose component in wet milling corn fibers from the pentose component for production of value-added products. Corn fibers were first pretreated with hot water at 121°C for 1 h followed by glucoamylase hydrolysis to remove starch. The remaining solid was then treated with hot water at 140–170°C followed by an enzymatic hydrolysis to further separate the hexose and pentose components. After the second pretreatment, the enzymatic digestibility of cellulose was much better than that of arabinoxylan. As a result, up to 90% arabinoxylan in corn fibers was retained in a solid form after the enzyme hydrolysis, while most of the hexose components were removed.     

Pretreatment and enzymatic hydrolysis of wheat straw (Triticum aestivum L.)--the impact of lignin relocation and plant tissues on enzymatic accessibility

Wheat straw is a potential feedstock for bioethanol production. This paper investigates tissues from whole internode sections subjected to hydrothermal pretreatment at 185 °C and subsequent enzymatic hydrolysis up to 144 h. Analyses revealed an increase in surface lignin as hydrolysis progressed, which could be coupled to the gradual decrease in hydrolysis rate over time. The data support the hypothesis of lignin extraction from the cell wall matrix during pretreatment and deposition as droplets upon cooling. These droplets are assumed to accumulate during enzymatic hydrolysis. Additionally, after 144 h of enzymatic hydrolysis the cortex had vanished, exposing the heavier lignified vascular tissue. Accumulation of lignin droplets and exposure of residual lignin could be part of the explanation for the decreasing hydrolysis rate. Flattening of macrofibrils after pretreatment together with more indentations on the surfaces was also observed, possibly caused by a proposed synergistic effect of cellobiohydrolases and endoglucanases.     

pH catalyzed pretreatment of corn bran for enhanced enzymatic arabinoxylan degradation

Corn bran is mainly made up of the pericarp of corn kernels and is a byproduct stream resulting from the wet milling step in corn starch processing. Through statistic modeling this study examined the optimization of pretreatment of corn bran for enzymatic hydrolysis. A low pH pretreatment (pH 2, 150 °C, 65 min) boosted the enzymatic release of xylose and glucose and maximized biomass solubilization. With more acidic pretreatment followed by enzymatic hydrolysis the total xylose release was maximized (at pH 1.3) reaching ～ 50% by weight of the original amount present in destarched corn bran, but the enzyme catalyzed xylose release was maximal after pretreatment at approx. pH 2. The total glucose release peaked after pretreatment of approx. pH 1.5 with an enzymatic release of approx. 68% by weight of the original amounts present in destarched corn bran. For arabinose the enzymatic release was negatively affected by the acidic pretreatment as labile arabinosyl-linkages were presumably hydrolysed directly during the pretreatment. A maximum of 60% arabinose release was achieved directly from the optimal (acidic) pretreatment. The total content of diferulic acids, supposedly involved in the cross-linking of the arabinoxylan polymers, decreased by both alkaline and acidic pretreatment pH, with the loss by alkaline pretreatments being highest. No direct correlation between the enzymatic release of xylose and the content of diferulic acids in the substrate could be verified. On the contrary the enzymatic release of xylose was significantly correlated to the total release of arabinose, indicating that the degree of arabinosyl-substitutions on the xylan backbone is an essential parameter for enzymatic hydrolysis of corn bran arabinoxylan.     

Scale-up and integration of alkaline hydrogen peroxide pretreatment, enzymatic hydrolysis, and ethanolic fermentation

Alkaline hydrogen peroxide (AHP) has several attractive features as a pretreatment in the lignocellulosic biomass‐to‐ethanol pipeline. Here, the feasibility of scaling‐up the AHP process and integrating it with enzymatic hydrolysis and fermentation was studied. Corn stover (1 kg) was subjected to AHP pretreatment, hydrolyzed enzymatically, and the resulting sugars fermented to ethanol. The AHP pretreatment was performed at 0.125 g H₂O₂/g biomass, 22°C, and atmospheric pressure for 48 h with periodic pH readjustment. The enzymatic hydrolysis was performed in the same reactor following pH neutralization of the biomass slurry and without washing. After 48 h, glucose and xylose yields were 75% and 71% of the theoretical maximum. Sterility was maintained during pretreatment and enzymatic hydrolysis without the use of antibiotics. During fermentation using a glucose‐ and xylose‐utilizing strain of Saccharomyces cerevisiae, all of the Glc and 67% of the Xyl were consumed in 120 h. The final ethanol titer was 13.7 g/L. Treatment of the enzymatic hydrolysate with activated carbon prior to fermentation had little effect on Glc fermentation but markedly improved utilization of Xyl, presumably due to the removal of soluble aromatic inhibitors. The results indicate that AHP is readily scalable and can be integrated with enzyme hydrolysis and fermentation. Compared to other leading pretreatments for lignocellulosic biomass, AHP has potential advantages with regard to capital costs, process simplicity, feedstock handling, and compatibility with enzymatic deconstruction and fermentation. Biotechnol. Bioeng. 2012; 109:922–931. © 2011 Wiley Periodicals, Inc.     

Two-stage hydrolysis of invasive algal feedstock for ethanol fermentation

The overall goal of this work was to develop a saccharification method for the production of third generation biofuel (i.e. bioethanol) using feedstock of the invasive marine macroalga Gracilaria salicornia. Under optimum conditions (120 °C and 2% sulfuric acid for 30 min), dilute acid hydrolysis of the homogenized invasive plants yielded a low concentration of glucose (4.1 mM or 4.3 g glucose/kg fresh algal biomass). However, two-stage hydrolysis of the homogenates (combination of dilute acid hydrolysis with enzymatic hydrolysis) produced 13.8 g of glucose from one kilogram of fresh algal feedstock. Batch fermentation analysis produced 79.1 g EtOH from one kilogram of dried invasive algal feedstock using the ethanologenic strain Escherichia coli KO11. Furthermore, ethanol production kinetics indicated that the invasive algal feedstock contained different types of sugar, including C(5) -sugar. This study represents the first report on third generation biofuel production from invasive macroalgae, suggesting that there is great potential for the production of renewable energy using marine invasive biomass.     

RT-CaCCO process: an improved CaCCO process for rice straw by its incorporation with a step of lime pretreatment at room temperature

We improved the CaCCO process for rice straw by its incorporation with a step of lime pretreatment at room temperature (RT). We firstly optimized the RT-lime pretreatment for the lignocellulosic part. When the ratio of lime/dry-biomass was 0.2 (w/w), the RT lime-pretreatment for 7-d resulted in an effect on the enzymatic saccharification of cellulose and xylan equivalent to that of the pretreatment at 120°C for 1h. Sucrose, starch and β-1,3-1,4-glucan, which could be often detected in rice straw, were mostly stable under the RT-lime pretreatment condition. Then, the pretreatment condition in the conventional CaCCO process was modified by the adaptation of the optimized RT lime-pretreatment, resulting in significantly better carbohydrate recoveries via enzymatic saccharification than those of the CaCCO process (120°C for 1 h). Thus, the improved CaCCO process (the RT-CaCCO process) could preserve/pretreat the feedstock at RT in a wet form with minimum loss of carbohydrates.     

The effect of milling parameters on starch hydrolysis of milled malt in the brewing process

The effect of milling parameters on the hydrolysis of starch during the mashing process was investigated. Hammer milling was compared against roll milling. Roll gap settings, roll speed, speed differential were also analysed, as well as comparing four- to six-roll milling. The parameter of differential speed was also studied through grist particle size distribution. Employing a 65 °C infusion type mashing process for the wort, the glucose and maltose concentrations of malts milled in different ways were analysed. Results showed that the glucose concentration in the wort after 45 min of mashing, obtained using a hammer mill, was the same as that achieved from roll milling in 60 min. For roller mill gap settings the 0.8 mm gap grist required 60 min of mashing to reach a glucose concentration of 3.46 g l⁻¹, whereas the 0.1 mm gap grist achieved the same level of starch hydrolysis in almost half the time, around 30–35 min of mashing. The results regarding roll speed showed that the 300 and 700 rpm mashes required roughly 50 and 40 min, respectively. Comparable sugar concentrations in the 50 rpm mash were obtained in 60 min. Finally, the comparison between simulated four- and six-roll milling showed the latter yielded higher glucose concentrations.