Tensile cervical facet capsule ligament mechanics: failure and subfailure responses in the rat

Clinical, epidemiological, and biomechanical studies suggest the involvement of the cervical facet joint in neck pain. Mechanical studies have suggested the facet capsular ligament to be at risk for subfailure tensile injury during whiplash kinematics of the neck. Ligament mechanical properties can be altered by subfailure injury and such loading can induce cellular damage. However, at present, there is no clear understanding of the physiologic context of subfailure facet capsular ligament injury and mechanical implications for whiplash-related pain. Therefore, this study aimed to define a relationship between mechanical properties at failure and a subfailure condition associated with pain for tension in the rat cervical facet capsular ligament. Tensile failure studies of the C6/C7 rat cervical facet capsular ligament were performed using a customized vertebral distraction device. Force and displacement at failure were measured and stiffness and energy to failure were calculated. Vertebral motions and ligament deformations were tracked and maximum principal strains and their directions were calculated. Mean tensile force at failure (2.96 +/- 0.69 N) was significantly greater (p < 0.005) than force at subfailure (1.17 +/- 0.48 N). Mean ligament stiffness to failure was 0.75 +/- 0.27 N/mm. Maximum principal strain at failure (41.3 +/- 20.0%) was significantly higher (p = 0.003) than the corresponding subfailure value (23.1 +/- 9.3%). This study determined that failure and a subfailure painful condition were significantly different in ligament mechanics and findings provide preliminary insight into the relationship between mechanics and pain physiology for this ligament. Together with existing studies, these findings offer additional considerations for defining mechanical thresholds for painful injuries.     

Anomalous fiber realignment during tensile loading of the rat facet capsular ligament identifies mechanically induced damage and physiological dysfunction

Many pathophysiological phenomena are associated with soft tissue loading that does not produce visible damage or tissue failure. As such, there is an unexplained disconnect between tissue injury and detectable structural damage during loading. This study investigated the collagen fiber kinematics of the rat facet capsular ligament to identify the onset of subfailure damage during tensile loading conditions that are known to induce pain. Quantitative polarized light imaging was used to determine the collagen fiber orientation in the capsular ligament (n=7) under tension, and an alignment vector correlation measurement was employed to identify local anomalous fiber realignment during loading. During the initial portion of loading when tissue stiffness was increasing, anomalous realignment was more likely to be detected than mechanical evidence of structural damage, and as a result, anomalous fiber realignment was identified significantly (p=0.004) before gross failure. The occurrence of anomalous fiber realignment was significantly associated (p=0.013) with a decrease in tangent stiffness during loading (ligament yield), suggesting this optical metric may be associated with a loss of structural integrity. The presence of localized anomalous realignment during subfailure loading in this tissue may explain the development of laxity, collagen fiber disorganization, and persistent pain previously reported for facet joint distractions comparable to that required for anomalous realignment. These optical data, together with the literature, suggest that mechanically induced tissue damage may occur in the absence of any macroscopic or mechanical evidence of failure and may produce local pathology and pain.     

Compressive and tensile mechanical properties of the porcine nasal septum

The expanding nasal septal cartilage is believed to create a force that powers midfacial growth. In addition, the nasal septum is postulated to act as a mechanical strut that prevents the structural collapse of the face under masticatory loads. Both roles imply that the septum is subject to complex biomechanical loads during growth and mastication. The purpose of this study was to measure the mechanical properties of the nasal septum to determine (1) whether the cartilage is mechanically capable of playing an active role in midfacial growth and in maintaining facial structural integrity and (2) if regional variation in mechanical properties is present that could support any of the postulated loading regimens. Porcine septal samples were loaded along the horizontal or vertical axes in compression and tension, using different loading rates that approximate the in vivo situation. Samples were loaded in random order to predefined strain points (2–10%) and strain was held for 30 or 120 seconds while relaxation stress was measured. Subsequently, samples were loaded until failure. Stiffness, relaxation stress and ultimate stress and strain were recorded. Results showed that the septum was stiffer, stronger and displayed a greater drop in relaxation stress in compression compared to tension. Under compression, the septum displayed non-linear behavior with greater stiffness and stress relaxation under faster loading rates and higher strain levels. Under tension, stiffness was not affected by strain level. Although regional variation was present, it did not strongly support any of the suggested loading patterns. Overall, results suggest that the septum might be mechanically capable of playing an active role in midfacial growth as evidenced by increased compressive residual stress with decreased loading rates. However, the low stiffness of the septum compared to surrounding bone does not support a strut role. The relatively low stiffness combined with high stress relaxation under fast loading rates suggests that the nasal septum is a stress dampener, helping to absorb and dissipate loads generated during mastication.     

Biomechanical response of human spleen in tensile loading

Blunt splenic injuries are most frequently caused as a result of motor vehicle collisions and are associated with high mortality rates. In order to accurately assess the risk of automotive related spleen injuries using tools such as finite element models, tissue level tolerance values and suitable material models must be developed and validated based on appropriate biomechanical data. This study presents a total of 41 tension tests performed on spleen parenchyma coupons and 29 tension tests performed on spleen capsule/parenchyma coupons. Standard dog-bone coupons were obtained from fresh human spleen and tested within 48 h of death. Each coupon was tested once to failure at one of the four loading rates to investigate the effects of rate dependence. Load and acceleration data were obtained at each of the specimen grips. High-speed video and optical markers placed on the specimens were used to measure local displacement. Failure stress and strain were calculated at the location of failure in the gage length of the coupon. The results of the study showed that both the spleen parenchyma and the capsule are rate dependent, with higher loading rates yielding higher failure stresses and lower failure strains. The results also show that the failure stress of the splenic capsule is significantly greater than that of the underlying parenchyma. Overall, this study provides novel biomechanical data that demonstrate the rate dependent tissue level tolerance values of human spleen tissue in tensile loading, which can aid in the improvement of finite element models used to assess injury risk in blunt trauma.     

Effect of loading rate on the compressive mechanics of the immature baboon cervical spine

Thirty-four cervical spine segments were harvested from 12 juvenile male baboons and compressed to failure at displacement rates of 5, 50, 500, or 5000 mm/s. Compressive stiffness, failure load, and failure displacement were measured for comparison across loading rate groups. Stiffness showed a significant concomitant increase with loading rate, increasing by 62% between rates of 5 and 5000 mm/s. Failure load also demonstrated an increasing relationship with loading rate, while displacement at failure showed no rate dependence. These data may help in the development of improved pediatric automotive safety standards and more biofidelic physical and computational models.     

Cervical facet capsular ligament yield defines the threshold for injury and persistent joint-mediated neck pain

The cervical facet joint has been identified as a source of neck pain, and its capsular ligament is a likely candidate for injury during whiplash. Many studies have shown that the mechanical properties of ligaments can be altered by subfailure injury. However, the subfailure mechanical response of the facet capsular ligament has not been well defined, particularly in the context of physiology and pain. Therefore, the goal of this study was to quantify the structural mechanics of the cervical facet capsule and define the threshold for altered structural responses in this ligament during distraction. Tensile failure tests were preformed using isolated C6/C7 rat facet capsular ligaments (n=8); gross ligament failure, the occurrence of minor ruptures and ligament yield were measured. Gross failure occurred at 2.45+/-0.60 N and 0.92+/-0.17 mm. However, the yield point occurred at 1.68+/-0.56 N and 0.57+/-0.08 mm, which was significantly less than gross failure (p<0.001 for both measurements). Maximum principal strain in the capsule at yield was 80+/-24%. Energy to yield was 14.3+/-3.4% of the total energy for a complete tear of the ligament. Ligament yield point occurred at a distraction magnitude in which pain symptoms begin to appear in vivo in the rat. These mechanical findings provide insight into the relationship between gross structural failure and painful loading for the facet capsular ligament, which has not been previously defined for such neck injuries. Findings also present a framework for more in-depth methods to define the threshold for persistent pain and could enable extrapolation to the human response.     

Cellular accommodation and the response of bone to mechanical loading

Several mathematical rules by which bone adapts to mechanical loading have been proposed. Previous work focused mainly on negative feedback models, e.g., bone adapts to increased loading after a minimum strain effective (MES) threshold has been reached. The MES algorithm has numerous caveats, so we propose a different model, according to which bone adapts to changes in its mechanical environment based on the principle of cellular accommodation. With the new algorithm we presume that strain history is integrated into cellular memory so that the reference state for adaptation is constantly changing. To test this algorithm, an experiment was performed in which the ulnae of Sprague-Dawley rats were loaded in axial compression. The animals received loading for 15 weeks with progressively decreasing loads, increasing loads, or a constant load. The results showed the largest increases in geometry in the decreasing load group, followed by the constant load group. Bone formation rates (BFRs) were significantly greater in the decreasing load group during the first 2 weeks of the study as compared to all other groups (P<0.05). After the first few weeks of mechanical loading, the BFR in the loaded ulnae returned to the values of the nonloaded ulnae. These experimental results closely fit the predicted results of the cellular accommodation algorithm. After the initial weeks of loading, bone stopped responding so the degree of adaptation was proportional to the initial peak load magnitude.     

Effect of displacement rate on the tensile mechanics of pediatric cervical functional spinal units

This study examined the effect of loading (displacement) rate on the tensile mechanics of cervical spine functional spinal units. A total of 40 isolated functional spinal units (two vertebrae and the adjoining soft tissues) from juvenile male baboons (10+/-0.6-human equivalent years old) were subjected to tensile loading spanning four orders of magnitude from 0.5 to 5000 mm/s. The stiffness, ultimate failure load, and corresponding displacement at failure were measured for each specimen and normalized by spinal geometry to examine the material properties as well as the structural properties. The tensile stiffness, failure load, normalized stiffness, and normalized failure load significantly increased (ANOVA, p<0.001) with increasing displacement rate. From the slowest to fastest loading rate, a two-fold increase in stiffness and four-fold increase in failure load were observed. The tensile failure strains (1.07+/-0.31 mm/mm strain) were not significantly correlated with loading rate (ANOVA, p=0.146). Both the functional (non-destructive stiffness and normalized stiffness) and failure mechanics of isolated functional spinal units exhibited a power-law relationship with displacement rate. Modeling efforts utilizing these rate-dependent characteristics will enhance our understanding of the tensile viscoelastic response of the spine and enable improved dynamic injury prevention schemes.     

Investigation of impact loading rate effects on the ligamentous cervical spinal load-partitioning using finite element model of functional spinal unit C2–C3

The cervical spine functions as a complex mechanism that responds to sudden loading in a unique manner, due to intricate structural features and kinematics. The spinal load-sharing under pure compression and sagittal flexion/extension at two different impact rates were compared using a bio-fidelic finite element (FE) model of the ligamentous cervical functional spinal unit (FSU) C2–C3. This model was developed using a comprehensive and realistic geometry of spinal components and material laws that include strain rate dependency, bone fracture, and ligament failure. The range of motion, contact pressure in facet joints, failure forces in ligaments were compared to experimental findings. The model demonstrated that resistance of spinal components to impact load is dependent on loading rate and direction. For the loads applied, stress increased with loading rate in all spinal components, and was concentrated in the outer intervertebral disc (IVD), regions of ligaments to bone attachment, and in the cancellous bone of the facet joints. The highest stress in ligaments was found in capsular ligament (CL) in all cases. Intradiscal pressure (IDP) in the nucleus was affected by loading rate change. It increased under compression/flexion but decreased under extension. Contact pressure in the facet joints showed less variation under compression, but increased significantly under flexion/extension particularly under extension. Cancellous bone of the facet joints region was the only component fractured and fracture occurred under extension at both rates. The cervical ligaments were the primary load-bearing component followed by the IVD, endplates and cancellous bone; however, the latter was the most vulnerable to extension as it fractured at low energy impact.     

Subfailure damage in ligament: a structural and cellular evaluation.

Subfailure damage in ligaments was evaluated macroscopically from a structural perspective (referring to the entire ligament as a structure) and microscopically from a cellular perspective. Freshly harvested rat medial collateral ligaments (MCLs) were used as a model in ex vivo experiments. Ligaments were preloaded with 0.1 N to establish a consistent point of reference for length (and strain) measurements. Ligament structural damage was characterized by nonrecoverable difference in tissue length after a subfailure stretch. The tissue's mechanical properties (via stress vs. strain curves measured from a preloaded state) after a single subfailure stretch were also evaluated (n = 6 pairs with a different stretch magnitude applied to each stretched ligament). Regions containing necrotic cells were used to characterize cellular damage after a single stretch. It should be noted that the number of damaged cells was not quantified and the difference between cellular area and area of fluorescence is not known. Structural and cellular damage were represented and compared as functions of subfailure MCL strains. Statistical analysis indicated that the onset of structural damage occurs at 5.14% strain (referenced from a preloaded length). Subfailure strains above the damage threshold changed the shape of the MCL stress-strain curve by elongating the toe region (i.e., increasing laxity) as well as decreasing the tangential modulus and ultimate stress. Cellular damage was induced at ligament strains significantly below the structural damage threshold. This cellular damage is likely to be part of the natural healing process in mildly sprained ligaments.     

Viscoelastic and failure properties of spine ligament collagen fascicles

The microstructural volume fractions, orientations, and interactions among components vary widely for different ligament types. If these variations are understood, however, it is conceivable to develop a general ligament model that is based on microstructural properties. This paper presents a part of a much larger effort needed to develop such a model. Viscoelastic and failure properties of porcine posterior longitudinal ligament (PLL) collagen fascicles were determined. A series of subfailure and failure tests were performed at fast and slow strain rates on isolated collagen fascicles from porcine lumbar spine PLLs. A finite strain quasi-linear viscoelastic model was used to fit the fascicle experimental data. There was a significant strain rate effect in fascicle failure strain (P < 0.05), but not in failure force or failure stress. The corresponding average fast-rate and slow-rate failure strains were 0.098 ± 0.062 and 0.209 ± 0.081. The average failure force for combined fast and slow rates was 2.25 ± 1.17 N. The viscoelastic and failure properties in this paper were used to develop a microstructural ligament failure model that will be published in a subsequent paper.     

The effect of loading rate on the development of early damage in articular cartilage

Experimental reports suggest that cartilage damage depends on strain magnitude. Additionally, because of its poro-viscoelastic nature, strain magnitude in cartilage can depend on strain rate. The present study explores whether cartilage damage may develop dependent on strain rate, even when the presented damage numerical model is strain-dependent but not strain-rate-dependent. So far no experiments have been distinguished whether rate-dependent cartilage damage occurs in the collagen or in the non-fibrillar network. Thus, this research presents a finite element analysis model where, among others, collagen and non-fibrillar matrix are incorporated as well as a strain-dependent damage mechanism for these components. Collagen and non-fibrillar matrix stiffness decrease when a given strain is reached until complete failure upon reaching a maximum strain. With such model, indentation experiments at increasing strain rates were simulated on cartilage plugs and damage development was monitored over time. Collagen damage increased with increasing strain rate from 21 to 42 %. In contrast, damage in the non-fibrillar matrix decreased with increasing strain rates from 72 to 34 %. Damage started to develop at a depth of approximately 20 % of the sample height, and this was more pronounced for the slow and modest loading rates. However, the most severe damage at the end of the compression step occurred at the surface for the plugs subjected to 120 mm/min strain rate. In conclusion, the present study confirms that the location and magnitude of damage in cartilage may be strongly dependent on strain rate, even when damage occurs solely through a strain-dependent damage mechanism.     

Methodology to determine failure characteristics of planar soft tissues using a dynamic tensile test

Predicting the injury risk in automotive collisions requires accurate knowledge of human tissues, more particularly their mechanical properties under dynamic loadings. The present methodology aims to determine the failure characteristics of planar soft tissues such as skin, hollow organs and large vessel walls. This consists of a dynamic tensile test, which implies high-testing velocities close to those in automotive collisions. To proceed, I-shaped tissue samples are subjected to dynamic tensile tests using a customized tensile device based on the drop test principle. Data acquisition has especially been adapted to heterogeneous and soft biological tissues given that standard measurement systems (considered to be global) have been completed with a non-contact and full-field strain measurement (considered to be local). This local measurement technique, called the Image Correlation Method (ICM) provides an accurate strain analysis by revealing strain concentrations and avoids damaging the tissue. The methodology has first been applied to human forehead skin and can be further expanded to other planar soft tissues. The failure characteristics for the skin in terms of ultimate stress are 3 MPa +/- 1.5 MPa. The ultimate global longitudinal strains are equal to 9.5%+/-1.9% (Green-Lagrange strain), which contrasts with the ultimate local longitudinal strain values of 24.0%+/-5.3% (Green-Lagrange strain). This difference is a consequence of the tissue heterogeneity, clearly illustrated by the heterogeneous distribution of the local strain field. All data will assist in developing the tissue constitutive law that will be implemented in finite element models.     

Insensitivity of tensile failure properties of human bridging veins to strain rate: implications in biomechanics of subdural hematoma

The effects of strain rate on tensile failure properties of human parasagittal bridging veins were studied in eight unembalmed cadavers. While bathed in physiological saline at 37 degrees C, the intact vessel was stretched axially by a servo-controlled hydraulic testing machine at either a low strain rate of 0.1-2.5 s-1 or a high rate of 100-250 s-1. The mean ultimate stretch ratios for low and high strain rates, respectively, were 1.51 +/- 0.24 (S.D. n = 29) and 1.55 +/- 0.15 (n = 34), and the ultimate stresses were 3.24 +/- 1.65 (n = 17) and 3.42 +/- 1.38 MPa (n = 20). Neither difference between strain rates was significant (p greater than 0.45). Thus, our results do not support the hypothesis that sensitivity of the ultimate strain of bridging veins to strain rate explains the acceleration tolerance data for subdural hematoma in primates [Gennarelli, R. A. and Thibault, L. E. (1982) Biomechanics of acute subdural hematoma. J. Trauma 22, 680-686].     

Evaluation of the influence of strain rate on Colles' fracture load

Colles' fracture, a transverse fracture of the distal radius bone, is one of the most frequently observed osteoporotic fractures resulting from low energy or traumatic events, associated with low and high strain rates, respectively. Although experimental studies on Colles' fracture were carried out at various loading rates ranging from static to impact loadings, there is no systematic study in the literature that isolates the influence of strain rate on Colles' fracture load. In order to provide a better understanding of fracture risk, the current study combines experimental material property measurements under varying strain rates with computational modeling and presents new information on the effect of strain rate on Colles' fracture. The simulation results showed that Colles' fracture load decreased with increasing strain rate with a steeper change in lower strain rates. Specifically, strain rate values (0.29s(-1)) associated with controlled falling without fracture corresponded to a 3.7% reduction in the fracture load. On the other hand, the reduction in the fracture load was 34% for strain rate of 3.7s(-1) reported in fracture inducing impact cadaver experiments. Further increase in the strain rate up to 18s(-1) led to an additional 22% reduction. The most drastic reduction in fracture load occurs at strain rates corresponding to the transition from controlled to impact falling. These results are particularly important for the improvement of fracture risk assessment in the elderly because they identify a critical range of loading rates (10-50mm/s) that can dramatically increase the risk of Colles' fracture.     

Mechanical response of porous scaffolds for cartilage engineering

Mechanical properties of scaffolds seeded with mesenchymal stem cells used for cartilage repair seem to be one of the critical factors in possible joint resurfacing. In this paper, the effect of adding hyaluronic acid, hydroxyapatite nanoparticles or chitosan nanofibers into the cross-linked collagen I on the mechanical response of the lyophilized porous scaffold has been investigated in the dry state at 37 oC under tensile loading. Statistical significance of the results was evaluated using ANOVA analysis. The results showed that the addition of hyaluronic acid significantly (p<0.05) reduced the tensile elastic modulus and enhanced the strength and deformation to failure of the modified cross-linked collagen I under the used test conditions. On the other hand, addition of hydroxyapatite nanoparticles and chitosan nanofibers, respectively, increased the elastic modulus of the modified collagen ten-fold and four-fold, respectively. Hydroxyapatite caused significant reduction in the ultimate deformation at break while chitosan nanofibers enhanced the ultimate deformation under tensile loading substantially (p<0.05). The ultimate tensile deformation was significantly (p<0.05) increased by addition of the chitosan nanofibers. The enhanced elastic modulus of the scaffold was translated into enhanced resistance of the porous scaffolds against mechanical load compared to scaffolds based on cross-linked neat collagen or collagen with hyaluronic acid with similar porosity. It can be concluded that enhancing the rigidity of the compact scaffold material by adding rigid chitosan nanofibers can improve the resistance of the porous scaffolds against compressive loading, which can provide more structural protection to the seeded mesenchymal stem cells when the construct is implanted into a lesion. Moreover, scaffolds with chitosan nanofibers seemed to enhance cell growth compared to the neat collagen I when tested in vitro as well as the scaffold stability, extending its resorption to more than 10 weeks.     

The influence of cryopreservation and quick-freezing on the mechanical properties of tendons

In order to maintain their native properties, cryopreserved tendons are usually used in biomechanical research and in transplantation of allogenic tendon grafts. The use of different study protocols leads to controversy in literature and thus complicates the evaluation of the current literature. The aim of this study consisted in examining the influence of different freezing and thawing temperatures on the mechanical properties of tendons. 60 porcine tendons were frozen at either −80 °C or −20 °C for 7 days and thawed at room or body temperature for 240 or 30 min, respectively. A subgroup of ten tendons was quick-frozen with liquid nitrogen (−196 °C) for 2 s before cryopreservation. Biomechanical testing was performed with a material testing machine and included creep, cyclic and load-to-failure tests. The results showed that freezing leads to a reduced creep strain after constant loading and to an increased secant modulus. Freezing temperature of −80 °C increased the secant modulus and decreased the strain at maximum stress, whereas thawing at room temperature reduced the maximum stress, the strain at initial tendon failure and the Young’s Modulus. Quick-freezing led to increased creep strain after constant loading, increased strain at initial failure in the load-to-failure test, and decreased strain at maximum stress. When cryopreserving, tendons for scientific or medical reasons, freezing temperature of −20 °C and thawing temperature of 37.5 °C are recommended to maintain the native properties of tendons. A treatment with liquid nitrogen in the sterilization process of tendon allografts is inadvisable because it alters the tendon properties negatively.     

Whole body vibration increases area and stiffness of the flexor carpi ulnaris tendon in the rat

Whole body vibration (WBV) has been extensively studied as an anabolic stimulus for bone and muscle. Therapeutic WBV delivers low magnitude, high frequency vibrations to tissues, eliciting biological and structural responses. This study investigated the effect of 0.3G (Peak-to-Peak), 30Hz sinusoidal vibration on intact flexor carpi ulnaris tendons in rats. Experimental rats were subjected to twenty minutes of WBV daily for five days a week for a total of five weeks. The tendon cross-sectional area and the structural properties of the muscle-tendon-bone unit under tensile loading to failure were evaluated. Initial body weights were similar between the groups and the mean change in body weight of the animals of each group did not differ. The cross-sectional area of the tendons of the vibrated animals was found to be 32% greater (P<0.05) than the controls and the structural stiffness of the vibrated tendons was found to be 41% greater (P<0.05) than the controls. For specimens that failed in the midsubstance of the tendon, a trend (P=0.087) for increased ultimate load was observed in the vibrated tendons compared to the controls. No differences in material properties were observed except for the strain to ultimate load, which was reduced 22% in the vibrated group. These initial findings suggest that vibration may serve as an anabolic stimulus to tendon similar to its effects on bone and muscle. These findings are important as they open the potential that low magnitude, high frequency vibration might serve as a means to accelerate tendon healing.     

Murine patellar tendon biomechanical properties and regional strain patterns during natural tendon-to-bone healing after acute injury

Tendon-to-bone healing following acute injury is generally poor and often fails to restore normal tendon biomechanical properties. In recent years, the murine patellar tendon (PT) has become an important model system for studying tendon healing and repair due to its genetic tractability and accessible location within the knee. However, the mechanical properties of native murine PT, specifically the regional differences in tissue strains during loading, and the biomechanical outcomes of natural PT-to-bone healing have not been well characterized. Thus, in this study, we analyzed the global biomechanical properties and regional strain patterns of both normal and naturally healing murine PT at three time points (2, 5, and 8 weeks) following acute surgical rupture of the tibial enthesis. Normal murine PT exhibited distinct regional variations in tissue strain, with the insertion region experiencing approximately 2.5 times greater strain than the midsubstance at failure (10.80±2.52% vs. 4.11±1.40%; mean±SEM). Injured tendons showed reduced structural (ultimate load and linear stiffness) and material (ultimate stress and linear modulus) properties compared to both normal and contralateral sham-operated tendons at all healing time points. Injured tendons also displayed increased local strain in the insertion region compared to contralateral shams at both physiologic and failure load levels. 93.3% of injured tendons failed at the tibial insertion, compared to only 60% and 66.7% of normal and sham tendons, respectively. These results indicate that 8 weeks of natural tendon-to-bone healing does not restore normal biomechanical function to the murine PT following injury.     

The importance of the elastic and plastic components of strain in tensile and compressive fatigue of human cortical bone in relation to orthopaedic biomechanics

The longevity, success, or failure of an orthopaedic implant is dependent on its osseointegration especially within the initial six months of the initial surgery. The development of strains plays a crucial role in both bone modelling and remodelling. For remodelling, in particular, strains of substantial values are required to activate the osteoblastic and osteoclastic activity for the osseointegration of the implant. Bone, however, is subject to "damage" when strain levels exceed a certain threshold level. Damage is manifested in the form of microcracks; it is linked to increased elastic strain amplitudes and is accompanied by the development of "plastic" (irrecoverable, residual) strains. Such strains increase the likelihood for the implant to subside or loosen. The present study examines the rates (per cycle) by which these two components of strain (elastic and "plastic") develop during fatigue cycling in two loading modes, tension and compression. The results of this study show that these strain rates depend on the applied stress in both loading modes. It also shows that elastic and plastic strain rates can be linked to each other through simple power law relationships so that one can calculate or predict the latter from the former and vice versa. We anticipate that such basic bone biomechanics data would be of great benefit to both clinicians and bioengineers working in the field of FEA modelling applications and orthopaedic implant surgery.