Cell immobilization technique for the enhanced production of alpha-galactosidase by Streptomyces griseoloalbus

Streptomyces griseoloalbus was immobilized in calcium alginate gel and the optimal immobilization parameters (concentrations of sodium alginate and calcium chloride, initial biomass and curing time) for the enhanced production of alpha-galactosidase were determined. The immobilization was most effective with 3% sodium alginate and 0.1M calcium chloride. The optimal initial biomass for immobilization was approximately 2.2g (wet wt.). The alginate-entrapped cells were advantageous because there was a twofold increase in the enzyme yield (55 U/ml) compared to the highest yield obtained with free cells (23.6 U/ml). Moreover, with immobilized cells the maximum yield was reached after 72 h of incubation in batch fermentation under optimal conditions, whereas in the case of free cells the maximum enzyme yield was obtained only after 96 h of incubation. The alginate beads had good stability and also retained 75% ability of enzyme production even after eight cycles of repeated batch fermentation. It is significant that this is the first report on whole-cell immobilization for alpha-galactosidase production.     

Production of alkaline protease by entrapped Bacillus licheniformis cells in repeated batch process

In this study, Bacillus licheniformis cells were immobilized by entrapment in calcium alginate beads and were used for production of alkaline protease by repeated batch process. In order to increase the stability of the beads, the immobilization procedure was optimized by statistical full factorial method, by which three factors including alginate type, calcium chloride concentration, and agitation speed were studied. Optimization of the enzyme production medium, by the Taguchi method, was also studied. The obtained results showed that optimization of the cell immobilization procedure and medium constituents significantly enhanced the production of alkaline protease. In comparison with the free-cell culture in pre-optimized medium, about 7.3-fold higher productivity was resulted after optimization of the overall procedure. Repeated batch mode of operation, using optimized conditions, resulted in continuous production of the alkaline protease for 13 batches in 19 days.     

Production of tannase by the immobilized cells of Bacillus licheniformis KBR6 in Ca-alginate beads

AIMS: The present study was aimed at finding the optimal conditions for immobilization of Bacillus licheniformis KBR6 cells in calcium-alginate (Ca-alginate) beads and determining the operational stability during the production of tannin-acyl-hydrolase (tannase) under semicontinous cultivation. METHODS AND RESULTS: The active cells of B. licheniformis KBR6 were immobilized in Ca-alginate and used for the production of tannase. The influence of alginate concentration (5, 10, 20 and 30 g l(-1)) and initial cell loading on enzyme production were studied. The production of tannase increased significantly with increasing alginate concentration and reached a maximum enzyme yield of 0.56 +/- 0.03 U ml(-1) at 20 g l(-1). This was about 1.70-fold higher than that obtained by free cells. The immobilized cells produced tannase consistently over 13 repeated cycles and reached a maximum level at the third cycle. Scanning electron microscope study indicated that the cells in Ca-alginate beads remain in normal shape. CONCLUSIONS: The Ca-alginate entrapment is a promising immobilization method of B. licheniformis KBR6 for repeated tannase production. Tannase production by immobilized cells is superior to that of free cells because it leads to higher volumetric activities within the same period of fermentation. SIGNIFICANCE AND IMPACT OF THE STUDY: This is the first report of tannase production from immobilized bacterial cells. The bacterium under study can produce higher amounts of tannase with respect to other fungal strains within a short cultivation period.     

Phytate degradation by immobilized<Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> phytase in soybean-curd whey

Saccharomyces cerevisiae CY phytase-producing cells were immobilized in calcium alginate beads and used for the degradation of phylate. The maximum activity and immobilization yield of the immobilized phytase reached 280 mU/g-bead and 43%, respectively. The optimal pH of the immobilized cell phytase was not different from that of the free cells. However, the optimum temperature for the immobilized phytase was 50°C, which was 10°C higher than that of the free cells; pH and thermal stability were enhanced as a consequence of immobilization. Using the immobilized phytase, phytate was degraded in a stirred tank bioreactor. Phytate degradation, both in a buffer solution and in soybean-curd whey mixture, showed very similar trends. At an enzyme dosage of 93.9 mU/g-phytate, half of the phytate was degraded after 1 h of hydrolysis. The operational stability of the immobilized beads was examined with repeated batchwise operations. Based on 50% conversion of the phytate and five times of reuse of the immobilized beads, the specific degradation (g phytate/g dry cell weight) for the immobilized phytase increased 170% compared to that of the free phytase.     

利用固定化重组大肠杆菌细胞生产D-塔格糖

利用经海藻酸钙包埋的重组大肠杆菌细胞催化D-半乳糖生产D-塔格糖,考察了细胞包埋量、反应条件对固定化细胞催化效率以及对D-塔格糖生产稳定性的影响。确定的最优转化条件为:温度65℃,pH 6.5,添加终浓度为1 mmol/L Mn²⁺,底物(D-半乳糖)浓度100 g/L,重组大肠杆菌细胞用量40 g/L。固定化小球在0.3%戊二醛溶液中交联30 min可以显著提高其在高温下的机械强度。考察了异构化反应体系中硼酸与底物间的摩尔比对产率的影响。研究结果表明,添加适量的硼酸可以改变原有的化学反应平衡,实现D-塔格糖的高产。利用D-半乳糖为底物在最优的反应条件下催化24 h,固定化细胞对D-半乳糖的转化率最高,可达65.8%,连续转化8批次的平均转化率为60.6%,为工业化生产D-塔格糖奠定了基础。     

Stabilization of Aspergillus parasiticus cytosine deaminase by immobilization on calcium alginate beads improved enzyme operational stability

Cytosine deaminase (CD) from Aspergillus parasiticus, which has half-life of 1.10?h at 37°C, was stabilized by immobilization on calcium alginate beads. The immobilized CD had pH and temperature optimum of 5 and 50°C respectively. The immobilized enzyme also stoichiometrically deaminated Cytosine and 5-fluorocytosine (5-FC) with the apparent K_M values of 0.60?mM and 0.65?mM respectively, displaying activation energy of 10.72 KJ/mol. The immobilization of native CD on calcium alginate beads gave the highest yield of apparent enzymatic activity of 51.60% of the original activity and the enzymatic activity was lost exponentially at 37°C over 12?h with a half-life of 5.80?h. Hence, the operational stability of native CD can be improved by immobilization on calcium alginate beads.     

Production of l (+) lactic acid by Lactobacillus delbrueckii immobilized in functionalized alginate matrices

The role of functionalized alginate gels as immobilized matrices in production of l (+) lactic acid by Lactobacillus delbrueckii was studied. L. delbrueckii cells immobilized in functionalized alginate beads showed enhanced bead stability and selectivity towards production of optically pure l (+) lactic acid in higher yields (1.74Yp/s) compared to natural alginate. Palmitoylated alginate beads revealed 99% enantiomeric selectivity (ee) in production of l (+) lactic acid. Metabolite analysis during fermentation indicated low by-product (acetic acid, propionic acid and ethanol) formation on repeated batch fermentation with functionalized immobilized microbial cells. The scanning electron microscopic studies showed dense entrapped microbial cell biomass in modified immobilized beads compared to native alginate. Thus the methodology has great importance in large-scale production of optically pure lactic acid.     

Enhanced production of alkaline thermostable keratinolytic protease from calcium alginate immobilized cells of thermoalkalophilic Bacillus halodurans JB 99 exhibiting dehairing activity

The thermoalkalophilic Bacillus halodurans JB 99 cells known for production of novel thermostable alkaline keratinolytic protease were immobilized in calcium alginate matrix. Batch and repeated batch cultivation using calcium alginate immobilized cells were studied for alkaline protease production in submerged fermentation. Immobilized cells with 2.5% alginate and 350 beads/flask of initial cell loading showed enhanced production of alkaline protease by 23.2% (5,275 ± 39.4 U/ml) as compared to free cells (4,280 ± 35.4 U/ml) after 24 h. In the semicontinuous mode of cultivation, immobilized cells under optimized conditions produced an appreciable level of alkaline protease in up to nine cycles and reached a maximal value of 5,975 U/ml after the seventh cycle. The enzyme produced from immobilized cells efficiently degraded chicken feathers in the presence of a reducing agent which can help the poultry industry in the management of keratin-rich waste and obtaining value-added products.     

Repeated batch production of epothilone B by immobilized Sorangium cellulosum

Production of extracellular epothilone B, one of the potent anticancer agents, by free and immobilized Sorangium cellulosum was studied using the repeated batch culture process. The concentration of alginate used in immobilization was directly related to the mass transfer rate of nutrients, mechanical stability, and the epothilone B production yield. With the optimized 3% (w/v) calcium alginate carrier, a prolonged repeated batch culture was investigated for the 5 repeated batches for 24 days. The maximum productivity of epothilone B obtained from the alginate-immobilized cells was 5.03 mg/l/day, which is 3 times higher than that of free cells (1.68 mg/l/day).     

Protease production by immobilized growing cells of Serratia marcescens and Myxococcus xanthus in calcium alginate gel beads

Summary Serratia marcescens and Myxococcus xanthus cells were immobilized in calcium alginate gel beads. Immobilization under various conditions had no effect on the extracellular proteolytic activity of S. marcescens cells. Protease production seemed rather to depend on the free cells in the medium. However, the stability over time of enzyme production was enhanced, as immobilization increased protease production half-life from 5 to 12 days. On the other hand, Myxococcus xanthus produced proteases inside the gel beads which could diffuse into the medium. The proteolytic activity increased as a function of the initial cell content of the beads and of the bead inoculum. Compared to free cells, immobilized cells of Myxococcus xanthus could produce 8 times more proteolytic activity, with a very low free-cell concentration in the medium.     

Effect of calcium on immobilization of rice (<Emphasis Type="Italic">Oryza sativa</Emphasis> L.) peroxidase for bioassays in sodium alginate and Agarose gel

The direct immobilization of soluble peroxidase isolated and partially purified from shoots of rice seedlings in calcium alginate beads and in calcium agarose gel was carried out. Peroxidase was assayed for guaiacol oxidation products in presence of hydrogen peroxide. The maximum specific activity and immobilization yield of the calcium agarose immobilized peroxidase reached 2,200 U mg⁻¹ protein (540 mU cm⁻³ gel) and 82%, respectively. In calcium alginate the maximum activity of peroxidase upon immobilization was 210 mU g⁻¹ bead with 46% yield. The optimal pH for agarose immobilized peroxidase was 7.0 which differed from the pH 6.0 for soluble peroxidase. The optimum temperature for the agarose immobilized peroxidase however was 30°C, which was similar to that of soluble peroxidase. The thermal stability of calcium agarose immobilized peroxidase significantly enhanced over a temperature range of 30∼60°C upon immobilization. The operational stability of peroxidase was examined with repeated hydrogen peroxide oxidation at varying time intervals. Based on 50% conversion of hydrogen peroxide and four times reuse of immobilized gel, the specific degradation of guaiacol for the agarose immobilized peroxidase increased three folds compared to that of soluble peroxidase. Nearly 165% increase in the enzyme protein binding to agarose in presence of calcium was noted. The results suggest that the presence of calcium, ions help in the immobilization process of peroxidase from rice shoots and mediates the direct binding of the enzyme to the agarose gel and that agarose seems to be a better immobilization matrix for peroxidase compared to sodium alginate.     

Enhanced shikonin production from Lithospermum erythrorhizon by in situ extraction and calcium alginate immobilization

Plant cell cultures of Lithospermum erythrorhizon were carried out to produce shikonin by in situ extraction and cell immobilization in calcium alginate bead in shake flask cultures. In situ product extraction and cell immobilization enhanced shikonin production and facilitated product recovery. In situ extraction by n-hexadecane and cell immobilization by calcium alginate gave higher specific shikonin productivities of 7.4 and 2.5 times, respectively, than those from the cultures of free cells without extraction. Simultaneous use of both techniques increased specific and volumetric productivities of shikonin 25- and 15-fold, respectively. In calcium alginate immobilized cell cultures, n-hexadecane addition at an early stage (before 15 days) was effective for shikonin production, and solvent addition after 15 days of the culture significantly reduced shikonin production. Higher numbers of plant cell immobilized bead inoculation did not increase shikonin production and sucrose consumption. Most of the produced shikonin was dissolved in the solvent layer.     

Immobilization of native and dextran-free dextransucrases from Leuconostoc mesenteroides NRRL B-512F for the synthesis of glucooligosaccharides

Dextransucrase from Leuconostoc mesenteroides NRRL B-512F was immobilized using two different methods: covalent attachment to activated silica and entrapment in calcium alginate. For immobilization on silica, native enzyme and dextran-free enzyme were compared. However, the entrapment in calcium alginate beads gave the best results in terms of immobilization yield and stability. This biocatalyst was employed in the acceptor reaction with maltose showing similar glucooligosaccharide production than the native enzyme but increased operational stability.     

Production of xylanase by immobilized Trichoderma reesei SAF3 in Ca-alginate beads

In the present study, the optimum conditions for the production of xylanase by immobilized spores of Trichoderma reesei SAF3 in calcium alginate beads were determined. The operational stability of the beads during xylanase production under semi-continuous fermentation was also studied. The influence of alginate concentration (1, 2, 3, and 4%) and initial cell loading (100, 200, 300, 400, and 500 beads per flask) on xylanase production was considered. The production of xylanase was found to increase significantly with increasing concentration of alginate and reached a maximum yield of 3.12 ± 0.18 U ml⁻¹ at 2% (w/v). The immobilized cells produced xylanase consistently up to 10 cycles and reached a maximum level at the forth cycle (3.36 ± 0.2 U ml⁻¹).     

Comparative study of production of dextransucrase and dextran by cells of Leuconostoc mesenteroides immobilized on Celite and in calcium alginate beads

In fed-batch fermentation, cells of L. mesenteroides immobilized on three types of Celite were used to produce dextransucrase (DS) followed by production of dextran. A layer of calcium alginate on the porous Celite R630 particles improved their mechanical stability, increased the amount of soluble DS produced and decreased the cell leakage from the highly porous support. Enzyme production with the immobilized cell cultures was significantly affected by both pore and particle size. Immobilized cultures using Celite R648 (average particle radius of 200 mum and pore size of 0.14 mum) produced the highest total enzymatic activity, followed by Celite R633, alginate-coated Celite R630, Celite R630, and then calcium alginate beads. Culture of free cells produced about 18% more total enzymatic activity than immobilized cells in calcium alginate beads, but about 64% less than immobilized cells on Celite R630. It is expected that larger amounts of enzymatic activity than measured are immobilized inside the alginate-coated Celite R630 and calcium alginate beads due to the mass transfer limitation conferred by the dextran product formed therein. The dextran yield from conversion of sucrose to dextran and fructose with all such enzyme-enriched, immobilized-cell cultures was higher than that obtained from free-cell culture under similar conditions.     

产糖化酶黑曲霉固定化方法比较的研究

采用海藻酸钙凝胶电埋法、以沸石、多孔聚酯等材料为固定化载体的吸附法固定黑曲霉（Aspergillus niger AS3.4309)菌丝细胞,以游离菌丝体作为对照,进行发酵产糖化酶的比较,结果表明：以聚酯泡沫作为固定化载体吸附固定化菌丝细胞产糖化酶活力最高。在产糖化酶的发酵过程中,与游离菌丝体细胞相比,固定化黑曲霉持续产酶时间有一定程度的延长。     

Calcium alginate immobilized hybridomas grown using a fluidized-bed perfusion system with a protein-free medium

Hybridoma SPO1 cells were immobilized in calcium alginate beads and were further grown in a fluidized-bed perfusion system with a protein-free medium. The presence of serum in the steps of entrapment was shown to be helpful for the preservation of cell viability. Each step during immobilization was investigated with respect to the extent of cell damage caused. The immobilization process using small beads caused a lower cell viability initially but allowed a higher rate of cell growth subsequently, compared to those in large beads. In a perfusion system for the continuous production of monoclonal antibodies (MAb), the viable cell density reached 2×10⁷ cells per ml of beads with a viability of 40%. Compared with the cells in suspension culture, the immobilized SPO1 cells showed higher viable cell based specific rates of substrate uptake (glucose and glutamine) and of MAb production. A significant drop in the formation of lactate after the cell growth entered a steady state suggested a higher activity of the Tricarboxylic Acid Cycle in the cells when the cell density became high.     

Immobilization of thermoalkalophilic recombinant esterase enzyme by entrapment in silicate coated Ca-alginate beads and its hydrolytic properties

Thermoalkalophilic esterase enzyme from Bal?ova (Agamemnon) geothermal site were aimed to be immobilized effectively via a simple and cost-effective protocol in silicate coated Calcium alginate (Ca-alginate) beads by entrapment. The optimal immobilization conditions of enzyme in Ca-alginate beads were investigated and obtained with 2% alginate using 0.5mg/ml enzyme and 0.7 M CaCl(2) solution. In order to prevent enzyme from leaking out of the gel beads, Ca-alginate beads were then coated with silicate. Enzyme loading efficiency and immobilization yield for silicate coated beads was determined as 98.1% and 71.27%, respectively and compared with non-coated ones which were 68.5% and 45.80%, respectively. Surface morphologies, structure and elemental analysis of both silicate coated and non-coated alginate beads were also compared using Fourier Transform Infrared Spectroscopy (FT-IR) and Scanning Electron Microscope (SEM) equipped with Energy-dispersive X-ray spectroscopy (EDX). Moreover, silicate coated alginate beads enhanced reusability of esterase in continuous processes compared to non-coated beads. The hydrolytic properties of free and immobilized enzyme in terms of storage and thermal stability as well as the effects of the temperature and pH were determined. It was observed that operational, thermal and storage stabilities of the esterase were increased with immobilization.     

Characterization of an encapsulation device for the production of monodisperse alginate beads for cell immobilization

An encapsulation device, designed on the basis of the laminar jet break-up technique, is characterized for cell immobilization with different types of alginate. The principle of operation of the completely sterilizable encapsulator, together with techniques for the continuous production of beads from 250 microm to 1 mm in diameter, with a size distribution below 5%, at a flow rate of 1-15 mL/min, is described. A modification of the device, to incorporate an electrostatic potential between the alginate droplets and an internal electrode, results in enhanced monodispersity with no adverse effects on cell viability. The maximum cell loading capacity of the beads strongly depends on the nozzle diameter as well as the cells used. For the yeast Phaffia rhodozyma, it is possible to generate 700 microm alginate beads with an initial cell concentration of 1 x 10(8) cells/mL of alginate whereas only 1 x 10(6) cells/ml could be entrapped within 400 microm beads. The alginate beads have been characterized with respect to mechanical resistance and size distribution immediately after production and as a function of storage conditions. The beads remain stable in the presence of acetic acid, hydrochloric acid, water, basic water, and sodium ions. The latter stability applies when the ratio of sodium: calcium ions is less than 1/5. Complexing agents such as sodium citrate result in the rapid solubilization of the beads due to calcium removal. The presence of cells does not affect the mechanical resistance of the beads. Finally, the mechanical resistance of alginate beads can be doubled by treatment with 5-10 kDa chitosan, resulting in reduced leaching of cells.