Direct electrochemistry and electrocatalysis of myoglobin on redox-active self-assembling monolayers derived from nitroaniline modified electrode

The adsorption processes and electrochemical behavior of 4-nitroaniline (4-NA) and 2-nitroaniline (2-NA) adsorbed onto glassy carbon electrodes (GCE) have been investigated in aqueous 0.1M nitric acid (HNO(3)) electrolyte solutions using cyclic voltammetry (CV). Nitroaniline adsorbs onto GCE surfaces and upon potential cycling past -0.55 V is transformed into the arylhydroxylamine (ArHA), which exhibits a well-behaved pH dependent redox couple centered at 0.32 V (pH 1.5). This modified electrode can be readily used as an immobilization matrix to entrap proteins and enzymes. In our studies, myoglobin (Mb) was chosen as a model protein for investigation. A pair of well-defined reversible redox peaks for Mb(Fe(III)-Fe(II)) was obtained at the Mb/arylhydroxylamine modified glassy carbon electrode (Mb/HAGCE) by direct electron transfer between the protein and the GCE. The formal potential (E(0')), the surface coverage (Gamma) and the electron transfer rate constant (k(s)) were calculated as -0.317 V, 4.15+/-0.5 x 10(-11)mol/cm(2) and 51+/-5s(-1), respectively. Dramatically enhanced biocatalytic activity was exemplified at the Mb/HAGCE for the reduction of hydrogen peroxide (H(2)O(2)), trichloroacetic acid (TCA) and oxygen (O(2)). The Mb/ArHA film was also characterized by UV-vis spectra, scanning electron microscope (SEM) indicating excellent stability and good biocompatibility for protein in the film. The applicability of the method to the determination of H(2)O(2) ( approximately 3%) in a commercial antiseptic solution and soft-contact lenses cleaning solutions were demonstrated. This new Mb/HAGCE exhibited rapid electrochemical response (with in 2s) with good stability in physiological condition.     

Direct electrochemistry and electrocatalysis of glucose oxidase immobilized on glassy carbon electrode modified by Nafion and ordered mesoporous silica-SBA-15

In this paper, it was found that glucose oxidase (GOD) has been stably immobilized on glassy carbon electrode modified by ordered mesoporous silica-SBA-15 and Nafion. The sorption behavior of GOD immobilized on SBA-15 matrix was characterized by transmission electron microscopy (TEM), ultraviolet–visible (UV–vis), FTIR, respectively, which demonstrated that SBA-15 can facilitate the electron exchange between the electroactive center of GOD and electrode. The direct electrochemistry and electrocatalysis behavior of GOD on modified electrode were characterized by cyclic voltammogram (CV) which indicated that GOD immobilized on Nafion and SBA-15 matrices displays direct, nearly reversible and surface-controlled redox reaction with an enhanced electron transfer rate constant of 3.89 s⁻¹ in 0.1 M phosphate buffer solution (PBS) (pH 7.12). Furthermore, it was also discovered that, in the absence of O₂, GOD immobilized on Nafion and SBA-15 matrices can produce a wide linear response to glucose in the positive potential range. Thus, Nafion/GOD-SBA-15/GC electrode is hopeful to be used in the third non-mediator's glucose biosensor. In addition, GOD immobilized on SBA-15 and Nafion matrices possesses an excellent bioelectrocatalytic activity for the reduction of O₂. The Nafion/GOD-SBA-15/GC electrode can be utilized as the cathode in biofuel cell.     

Direct electrochemistry and electrocatalysis of heme proteins immobilized on gold nanoparticles stabilized by chitosan

Three heme proteins, myoglobin, hemoglobin, and cytochrome c, have been adsorbed onto chitosan-stabilized gold nanoparticles (Chit-Aus) modified Au electrode via a molecule bridge like cysteine. UV-vis spectra indicated that the proteins on Chit-Aus films retained near-native secondary structures. The fabricated procedures and electrochemical behaviors of proteins on such an interface were characterized with electrochemical impedance spectra and cyclic voltammetric techniques. It was demonstrated that Chit-Aus film could not only offer a friendly environment to immobilize protein molecules but also enhance the electron transfer ability between protein molecules and underlying electrode. The effects of scan rate and pH on the electrochemical behaviors of each heme protein are discussed in detail. The resultant electrode displayed an excellent electrocatalytic response to the reduction of H(2)O(2), long-term stability, and good reproducibility.     

Influence of pH and ionic strength on the adsorption, leaching and activity of myoglobin immobilized onto ordered mesoporous silicates

Myoglobin has been immobilized onto different ordered mesoporous silicates. The effect of the pH on the adsorption, leaching and activity was studied. The results showed that the maximum amount of protein was adsorbed at a pH 6.5, just below the protein isoelectric point (7–7.3). There was no effect of increasing ionic strength on the adsorption profile at different pH values. The adsorption is rationalized in terms of local electrostatic forces acting between the enzyme and the silica surface as well as hydrophobic interactions close to the protein isoelectric point, whereas at low pH the global charges give rise to protein–protein repulsion and at high pH enzyme–silica repulsion. Higher amounts of immobilized myoglobin were leached at a pH 4, while lower amounts were leached at pH 6.5. The catalytic activity of myoglobin immobilized onto SBA-15 showed optimal activity at a pH 6.5 in comparison to a pH of 5 for the free form.     

Direct electron transfer and bioelectrocatalysis of hemoglobin at a carbon nanotube electrode

A stable suspension of carbon nanotube (CNT) can be obtained by dispersing the CNT in the solution of the surfactant cetyltrimethylammonium bromide. CNT has promotion effects on the direct electron transfer of hemoglobin (Hb), which was immobilized onto the surface of CNT. The direct electron transfer rate of Hb was greatly enhanced after it was immobilized onto the surface of CNT. Cyclic voltammetric results showed a pair of well-defined redox peaks, which corresponded to the direct electron transfer of Hb, with the formal potential (E^0′) at about −0.343 V (vs. saturated calomel electrode) in the phosphate buffer solution (pH 6.8). The electrochemical parameters such as apparent heterogeneous electron transfer rate constant (k_s) and the value of formal potential (E^0′) were estimated. The dependence of E^0′ on solution pH indicated that the direct electron transfer reaction of Hb is a one-electron transfer coupled with a one-proton transfer reaction process. The experimental results also demonstrated that the immobilized Hb retained its bioelectrocatalytic activity to the reduction of H₂O₂. The electrocatalytic current was proportional to the concentration of H₂O₂ at least up to 20 mM.     

Direct electrochemistry and electrocatalysis of hemoglobin immobilized on carbon paste electrode by silica sol-gel film

Direct electrochemical and electrocatalytic behaviors of hemoglobin (Hb) immobilized on carbon paste electrode (CPE) by a silica sol-gel film derived from tetraethylorthosilicate (TEOS) were investigated for the first time. Hb/sol-gel film modified electrodes showed a pair of well-defined and nearly reversible cyclic voltammetric peaks for Hb Fe(III)/Fe(II) redox couple at about -0.312 V (versus Ag/AgCl) in a pH 7.0 phosphate buffer. The formal potential of Hb heme Fe(III)/Fe(II) couple varied linearly with the increase of pH in the range of 5.0-10.0 with a slope of 49.44 mV pH(-1), which suggests that a proton transfer is accompanied with each electron transfer (ET) in the electrochemical reaction. The immobilized Hb displayed the features of peroxidase and gave excellent electrocatalytic performance to the reduction of O2, NO2(-) and H2O2. The calculated apparent Michaelis-Menten constant was 8.98 x 10(-4)M, which indicated that there was a large catalytic activity of Hb immobilized on CPE by sol-gel film toward H2O2. In comparison with other electrodes, the chemically modified electrodes, used in this direct electrochemical study of Hb, are easy to be fabricated and rather inexpensive. Consequently, the Hb/sol-gel film modified electrode provides a convenient approach to perform electrochemical research on this kind of proteins. It also has potential use in the fabrication of the third generation biosensors and bioreactors.     

Direct electron transfer and enzymatic activity of hemoglobin in a hexagonal mesoporous silica matrix

The direct electrochemistry of hemoglobin (Hb) immobilized on a hexagonal mesoporous silica (HMS)-modified glassy carbon electrode was described. The interaction between Hb and the HMS was investigated using UV-Vis spectroscopy, FT-IR, and electrochemical methods. The direct electron transfer of the immobilized Hb exhibited two couples of redox peaks with the formal potentials of -0.037 and -0.232 V in 0.1 M (pH 7.0) PBS, respectively, which corresponded to its two immobilized states. The electrode reactions showed a surface-controlled process with a single proton transfer at the scan rate range from 20 to 200 mV/s. The immobilized Hb retained its biological activity well and displayed an excellent response to the reduction of both hydrogen peroxide (H2O2) and nitrate (NO2-). Its apparent Michaelis-Menten constants for H2O2 and NO2- were 12.3 and 49.3 microM, respectively, showing a good affinity. Based on the immobilization of Hb on the HMS and its direct electrochemistry, two novel biosensors for H2O2 and NO2- were presented. Under optimal conditions, the sensors could be used for the determination of H2O2 ranging from 0.4 to 6.0 microM and NO2- ranging from 0.2 to 3.8 microM. The detection limits were 1.86 x 10(-9) M and 6.11 x 10(-7) M at 3sigma, respectively. HMS provided a good matrix for protein immobilization and biosensor preparation.     

Direct electrochemistry and electrocatalytic activity of catalase incorporated onto multiwall carbon nanotubes-modified glassy carbon electrode

The direct voltammetry and electrocatalytic properties of catalase, which was adsorbed on the surface of multiwall carbon nanotubes (MWCNTs), was investigated. A pair of well-defined and nearly reversible cyclic voltammetry peaks for Fe(III)/Fe(II) redox couple of catalase adsorbed on the surface of MWCNTs at approximately -0.05 V versus reference electrode in pH 6.5 buffer solution, indicating the direct electron transfer between catalase and electrode. The surface coverage of catalase immobilized on MWCNTs glassy carbon electrode was approximately 2.4x10(-10) molcm-2. The transfer coefficient (alpha) was calculated to be 0.4, and the heterogeneous electron transfer rate constant was 80 s-1 in pH 7, indicating great facilitation of the electron transfer between catalase and MWCNTs adsorbed on the electrode surface. The formal potential of catalase Fe(III)/Fe(II) couple in MWCNTs film had a linear relationship with pH values between 2 and 11 with a slope of 58 mV/pH, showing that the electron transfer is accompanied by single proton transportation. Catalase adsorbed on MWCNTs exhibits a remarkable electrocatalytic activity toward the reduction of oxygen and hydrogen peroxide. The value for calculated Michaelis-Menten constant (1.70 mM) was high, indicating the potential applicability of the films as a new type of reagentless biosensor based on the direct electrochemistry of the catalase enzyme.     

Direct electron transfer of hemoglobin in layered alpha-zirconium phosphate with a high thermal stability

A heme protein hemoglobin (Hb) was reacted with preexfoliated layered alpha-zirconium phosphate (alpha-ZrP) platelets. An X-ray diffraction (XRD) pattern of small range showed that the exfoliated alpha-ZrP platelets reassembled after the addition of Hb molecules, with the protein intercalated between the layers. UV-Vis and Fourier transform infrared (FTIR) spectra analysis displayed that no significant denaturation occurred to the intercalated protein. The bioactivity of Hb was also investigated by testing the electrochemical properties of the Hb/alpha-ZrP composite. Results showed that the intercalation of Hb into the layered material not only improved the thermal stability of Hb but also enhanced the direct electron transfer ability between protein molecules and electrode. The protein still showed bioactivity after treatment at a temperature as high as 85 degrees C. A pair of well-defined redox peaks at approximately -0.37 and -0.32V was observed on the cyclic voltammograms (CVs) of the Hb/alpha-ZrP composite modified electrode, and the electrode reactions showed a surface-controlled process with a single proton transfer. The resultant biosensor constructed by the Hb/alpha-ZrP composite displayed an excellent response to the reduction of hydrogen peroxide (H(2)O(2)) with good reproducibility.     

Direct electrochemistry of hemoglobin in dimethyldioctadecyl ammonium bromide film and its electrocatalysis to nitric oxide

Hemoglobin (Hb) was successfully immobilized in dimethyldioctadecyl ammonium bromide (DOAB) film at pyrolytic graphite (PG) electrode. Electrochemical experiments revealed that Hb in DOAB film exhibited a pair of well-defined, quasi-reversible cyclic voltammetric peaks at about -0.160 V versus saturated calomel electrode (SCE) in pH 5.0 buffer, characteristic of the heme Fe(III)/Fe(II) redox couple of Hb. The electron transfer (eT) rate between Hb and the PG electrode was 0.10 s(-1). Positions of the Soret absorbance band indicated that the Hb retained its secondary structure and was similar to its native state. Furthermore, the Hb in DOAB film acted as a biological catalyst towards the reduction of nitric oxide (NO). The voltammetric response of NO at the Hb-DOAB modified electrode could be used to determine the concentration of NO in solution.     

Construction and direct electrochemistry of orientation controlled laccase electrode

A laccase has multiple redox centres. Chemisorption of laccases on a gold electrode through a polypeptide tag introduced at the protein surface provides an isotropic orientation of laccases on the Au surface, which allows the orientation dependent study of the direct electrochemistry of laccase. In this paper, using genetic engineering technology, two forms of recombinant laccase which has Cys-6×His tag at the N or C terminus were generated. Via the Au-S linkage, the recombinant laccase was assembled orientationally on gold electrode. A direct electron transfer and a bioelectrocatalytic activity toward oxygen reduction were observed on the two orientation controlled laccase electrodes, but their electrochemical behaviors were found to be quite different. The orientation of laccase on the gold electrode affects both the electron transfer pathway and the electron transfer efficiency of O₂ reduction. The present study is helpful not only to the in-depth understanding of the direct electrochemistry of laccase, but also to the development of laccase-based biofuel cells.     

A novel nitrite biosensor based on the direct electron transfer of hemoglobin immobilized on CdS hollow nanospheres

A novel nitrite biosensor based on the direct electron transfer of hemoglobin (Hb) immobilized on CdS hollow nanospheres (HS-CdS) modified glassy carbon electrode was constructed. The direct electron transfer of Hb showed a pair of redox peaks with a formal potential of -286 mV (vs. SCE) in 0.1M pH 7.0 phosphate buffer solution. It was a surface-controlled electrode process involving a single proton transfer coupled with a reversible one-electron transfer for each heme group of Hb. HS-CdS had a large specific surface area and good biocompatibility and had a better electrochemical response than that of solid spherical CdS. The immobilized Hb on HS-CdS displayed an excellent response to NO(2)(-) with one irreversible electrode process for NO reduction. Under optimal conditions, the biosensor could be used for the determination of NO(2)(-) with a linear range from 0.3 to 182 microM and a detection limit of 0.08 microM at 3 sigma based on the irreversible reduction of NO. HS-CdS provided a good matrix for protein immobilization and had a promising application in constructing sensors.     

Direct electrochemistry and electrocatalysis based on a film of horseradish peroxidase intercalated into Ni-Al layered double hydroxide nanosheets

Positively charged Ni-Al layered double hydroxide nanosheets (Ni-Al LDHNS) have been used for the first time as matrices for immobilization of horseradish peroxidase (HRP) in order to fabricate enzyme electrodes for the purpose of studying direct electron transfer between the redox centers of proteins and underlying electrodes. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) revealed that the HRP-Ni-Al LDHNS film had an ordered structure and that HRP was intercalated into Ni-Al LDHNS with a monolayer arrangement. Field emission scanning electron microscopy (FESEM) showed that the HRP-Ni-Al LDHNS film had a uniform, porous morphology. UV-vis spectroscopy indicated that the intercalated HRP retained its native structure after incorporation in the Ni-Al LDHNS film. The immobilized HRP in Ni-Al LDHNS on the surface of a glassy carbon electrode (GCE) exhibited good direct electrochemical and electrocatalytic responses to the reduction of hydrogen peroxide (H(2)O(2)) and trichloroacetic acid (TCA). The resulting H(2)O(2) biosensor showed a wide linear range from 6.00x10(-7)M to 1.92x10(-4)M, low detection limit (4.00x10(-7)M) and good stability. The results show that Ni-Al LDHNS provide a novel and efficient platform for the immobilization of enzymes and realizing direct electrochemistry and that the materials have potential applications in the fabrication of third-generation biosensors.     

Layer-by-layer fabrication and direct electrochemistry of glucose oxidase on single wall carbon nanotubes

Layer-by-layer assembly of glucose oxidase (GOx) with single-wall carbon nanotubes (SWCNTs) is achieved on the electrode surface based on the electrostatic attraction between positively charged GOx in pH 3.8 buffer and negatively charged carboxylic groups of CNTs. The cyclic voltammetry and electrochemical impedance spectroscopy are used to characterize the formation of multilayer films. In deaerated buffer solutions, the cyclic voltammetry of the multilayer films of {GOx/CNT}_n shows two pairs of well-behaved redox peaks that are assigned to the redox reactions of CNTs and GOx, respectively, confirming the effective immobilization of GOx on CNTs using the layer-by-layer technique. The redox peak currents of GOx increase linearly with the increased number of layers indicating the uniform growth of GOx in multilayer films. The dependence of the cyclic voltammetric response of GOx in multilayer films on the scan rate and pH is also studied. A linear decrease of the reduction current of oxygen at the {GOx/CNT}-modified electrodes with the addition of glucose suggests that such multilayer films of GOx retain the bioactivity and can be used as reagentless glucose biosensors.     

Laccase from Pleurotus sajor-caju on functionalised SBA-15 mesoporous silica: Immobilisation and use for the oxidation of phenolic compounds

Laccase from Pleurotus sajor-caju was immobilised on functionalised SBA-15 mesoporous silica. The immobilisation process reached the equilibrium after about 100 min. In order to study the effect of loading (L) on activity of the immobilised laccase, the adsorption isotherm was built and the activity of the corresponding immobilised biocatalysts was determined. The activity of the immobilised preparations reached a maximum at L = 217 kU g_SBA-15⁻¹, whereas higher loadings gave rise to a less-efficient biocatalyst. The immobilised laccase was used for the oxidation of a mixture of four phenolic compounds (protocatechuic acid, ferulic acid, sinapic acid and caffeic acid) chosen among those present in olive mill wastewaters (OMWs). These compounds determine the phytotoxicity of OMWs. Different reaction rates were observed for the oxidation of the examined phenolic compounds. The biocatalyst was recycled and a conversion of 84 mol% at the 10th reuse and of about 60 mol% after the 14th reuse was obtained. In conclusion, the laccase immobilised on SBA-15 is a potential biocatalyst for bioremediation of OMWs, which is an important environmental problem in the regions around the Mediterranean Sea.     

Direct electrochemistry and electrocatalysis of hemoglobin on polypyrrole-Fe3O4/dodecyltrimethylammonium bromide-modified carbon paste electrode and its biosensing for hydrogen peroxide

Abstract

A novel hydrogen peroxide (H₂O₂) biosensor was successfully constructed, based on the immobilization of hemoglobin (Hb) on polypyrrole (PPy)-Fe₃O₄ and dodecyltrimethylammonium bromide (DTAB) composite ?lm-modified carbon paste electrodes (CPE). The PPy-Fe₃O₄ composites were synthesized in the suspension solution of Fe₃O₄ nanoparticles via in situ chemical oxidative polymerization under the direction of cationic surfactant cetyl trimethyl ammonium bromide. Spectroscopic and electrochemical examinations illustrated that the PPy-Fe₃O₄/DTAB composites were a biocompatible matrix for immobilizing Hb, which revealed high chemical stability and excellent biocompatibility. The thermodynamic, dynamic, and catalytic performance of the biosensor were analysed using cyclic voltammetry (CV). The results indicated that the PPy-Fe₃O₄/Hb/DTAB/CPE exhibited excellent electrocatalytic activity in the reduction of H₂O₂ with a high sensitivity (104 μA mM^{? 1}). The catalytic reduction currents of H₂O₂ were linearly related to H₂O₂ concentration in the range from 2.5 μM to 60 μM with a detection limit of 0.8 μM (S/N = 3). With such superior characteristics, this biosensor for H₂O₂ can be potentially applied in determination of other reactive oxygen species as well. These results indicated that PPy-Fe₃O₄/DTAB composites are a promising matrix for bioactive molecule immobilization.     

Recent developments and applications of immobilized laccase

Laccase is a promising biocatalyst with many possible applications, including bioremediation, chemical synthesis, biobleaching of paper pulp, biosensing, textile finishing and wine stabilization. The immobilization of enzymes offers several improvements for enzyme applications because the storage and operational stabilities are frequently enhanced. Moreover, the reusability of immobilized enzymes represents a great advantage compared with free enzymes. In this work, we discuss the different methodologies of enzyme immobilization that have been reported for laccases, such as adsorption, entrapment, encapsulation, covalent binding and self-immobilization. The applications of laccase immobilized by the aforementioned methodologies are presented, paying special attention to recent approaches regarding environmental applications and electrobiochemistry.