Thermophilic anaerobic digestion of Lurgi coal gasification wastewater in a UASB reactor

Lurgi coal gasification wastewater (LCGW) is a refractory wastewater, whose anaerobic treatment has been a severe problem due to its toxicity and poor biodegradability. Using a mesophilic (35 ± 2 °C) reactor as a control, thermophilic anaerobic digestion (55 ± 2 °C) of LCGW was investigated in a UASB reactor. After 120 days of operation, the removal of COD and total phenols by the thermophilic reactor could reach 50-55% and 50-60% respectively, at an organic loading rate of 2.5 kg COD/(m³ d) and HRT of 24 h; the corresponding efficiencies were both only 20-30% in the mesophilic reactor. After thermophilic digestion, the wastewater concentrations of the aerobic effluent COD could reach below 200 mg/L compared with around 294 mg/L if mesophilic digestion was done and around 375 mg/L if sole aerobic pretreatment was done. The results suggested that thermophilic anaerobic digestion improved significantly both anaerobic and aerobic biodegradation of LCGW.     

Improvement of the anaerobic treatment of potato processing wastewater in a UASB reactor by co-digestion with glycerol

The effect of three different types of glycerol on the performance of up-flow anaerobic sludge blanket (UASB) reactors treating potato processing wastewater was investigated. High COD removal efficiencies were obtained in both control and supplemented UASB reactors (around 85%). By adding 2 ml glycerol product per liter of raw wastewater, the biogas production could be increased by 0.74 l biogas ml⁻¹ glycerol product, which leads to energy values in the range of 810–1270 kWh_electric per m³ product. Moreover, a better in-reactor biomass yield was observed for the supplemented UASB reactor (0.012 g VSS g⁻¹ COD_removed) compared to the UASB control (0.002 g VSS g⁻¹ COD_removed), which suggests a positive effect of glycerol on the sludge blanket growth.     

Treatment of poultry slaughterhouse wastewater in hybrid upflow anaerobic sludge blanket reactor packed with pleated poly vinyl chloride rings

In this study, the performance of 5.4 L hybrid upflow anaerobic sludge blanket (HUASB) reactor for treating poultry slaughterhouse wastewater under mesophilic conditions (29-35 °C), was investigated. After starting-up, the reactor was loaded up to an OLR of 19 kg COD/m³ d and achieved varied TCOD and SCOD removal efficiencies of 70-86% and 80-92%, respectively. The biogas was varied between 1.1 and 5.2 m³/m³ d with the maximum methane content of 72%. The maximum methane yield was 0.32 m³/kg COD_removed at an OLR of 9.27 kg COD/m³ d. Black matured granules of size between 2.5 and 5 mm were observed at the end of 225 d operation. RTD study showed the flow behavior was in mixed regime at the end of performance study. Step wise polynomial regression analysis was fitted well. Methanobacterium and Methanosaeta bacteria were dominant at the end of start-up whereas Methanosarcina, Cocci and rods were predominant at the end of performance studies.     

Use of the Static Granular Bed Reactor (SGBR) with anaerobic sludge to treat poultry slaughterhouse wastewater and kinetic modeling

Poultry slaughterhouses discharge very high amount of wastewaters and these wastewaters can be treated successfully at a very low cost using anaerobic treatment. In this study, the Static Granular Bed Reactor (SGBR), a newly developed anaerobic process which is fully anaerobic granule, and another Static Granular Bed Reactor containing both anaerobic granular biomass and non-granular biomass were employed for the treatment of poultry slaughterhouse wastewater. The objective of the use of two reactors having different types of anaerobic biomass is to evaluate whether anaerobic sludge could be used effectively instead of anaerobic granule, which is much more difficult to obtain than the other during the start up period. Average COD removal efficiencies were greater than 95% for both of the reactors. Furthermore, Grau second-order and modified Stover–Kincannon models were successfully used to develop a kinetic model of the experimental data with a high correlation coefficient (R² > 0.95).     

Design and analysis of a solar reactor for anaerobic wastewater treatment

The aim of this research was to design a solar heated reactor system to enhance the anaerobic treatment of wastewater or biological sludge at temperatures higher than the ambient air temperature. For the proposed reactor system, the solar energy absorbed by flat plate collectors was transferred to a heat storage tank, which continuously supplied an anaerobic-filter reactor with water at a maximum temperature of 35 degrees C. The packed reactor was a metallic cylindrical tank with a peripheral twin-wall enclosure. Inside this enclosure was circulated warm water from the heat storage tank. Furthermore, a mathematical model was developed for the prediction of the temperature distribution within the reactor under steady state conditions. Preliminary results based on model simulations performed with meteorological data from various geographical regions of the world suggested that the proposed solar reactor system could be a promising and environmentally friendly approach for anaerobic treatment of wastewater and biological sludge.     

High strength sewage treatment in a UASB reactor and an integrated UASB-digester system

The treatment of high strength sewage was investigated in a one-stage upflow anaerobic sludge blanket (UASB) reactor and a UASB-digester system. The one-stage UASB reactor was operated in Palestine at a hydraulic retention time (HRT) of 10h and at ambient air temperature for a period of more than a year in order to asses the system response to the Mediterranean climatic seasonal temperature fluctuation. Afterwards, the one-stage UASB reactor was modified to a UASB-digester system by incorporating a digester operated at 35 degrees C. The achieved removal efficiencies in the one-stage UASB reactor for total, suspended, colloidal, dissolved and VFA COD were 54, 71, 34, 23%, and -7%, respectively during the first warm six months of the year, and achieved only 32% removal efficiency for COD total over the following cold six months of the year. The modification of the one-stage UASB reactor to a UASB-digester system had remarkably improved the UASB reactor performance as the UASB-digester achieved removal efficiencies for total, suspended, colloidal, dissolved and VFA COD of 72, 74, 74, 62 and 70%. Therefore, the anaerobic treatment of high strength sewage during the hot period in Palestine in a UASB-digester system is very promising.     

A kinetic analysis and experimental validation of an integrated system of anaerobic filter and biological aerated filter

An anaerobic/aerobic filter (AF/BAF) system was developed treating dairy wastewater. The influent was blended with recirculated effluent to allow for pre-denitrification in the AF followed by nitrification in the BAF. The recirculation ratio ranged 100-300%. The average chemical oxygen demand (COD) removal efficiency was 79.8-86.8% in the AF and the average total nitrogen removal efficiency was 50.5-80.8% in the AF/BAF system. Steady-state mass balances on the AF were used to analyze removal kinetics in the AF. The kinetic model values for effluent COD in the AF were overestimated as compared with experimental data. The integrated suspended and attached biomass growth rates in the AF were estimated. The specific growth rate of the integrated biomass at each recirculation ratios was 0.6213, 0.6647, and 1.20831/day, respectively. The increase in specific growth rate corresponded to increases in biomass sloughing as the recirculation ratio increased.     

Performance of down-flow hanging sponge (DHS) reactor coupled with up-flow anaerobic sludge blanket (UASB) reactor for treatment of onion dehydration wastewater

In this study, a promising system consisting of up-flow anaerobic sludge blanket (UASB) reactor followed by down-flow hanging sponge (DHS) reactor was investigated for onion dehydration wastewater treatment. Laboratory experiments were conducted at two different phases, i.e., phase (1) at overall hydraulic retention time (HRT) of 11 h (UASB reactor: 6 h and DHS reactor: 5 h) and phase (2) at overall HRT of 9.4 h (UASB reactor: 5.2 h and DHS reactor: 4.2 h). Long-term operation results of the proposed system showed that its overall TCOD, TBOD, TSS, TKN and NH₄N removal efficiencies were 92 ± 5, 95 ± 2, 95 ± 2, 72 ± 6 and 99 ± 1.3%, respectively (phase 1). Corresponding values for the 2nd phase were 85.4 ± 5, 86 ± 3, 87 ± 6, 65 ± 8 and 95 ± 2.8%. Based on the available results, the proposed system could be more viable option for treatment of wastewater generated from onion dehydration industry in regions with tropical or sub-tropical climates and with stringent discharge standards.     

Assessing the presence of BSE and scrapie in slaughterhouse wastewater

Aims: This paper describes a procedure for evaluating the presence and the stability of the proteinase K-resistant form of the prion protein (PrP^res) in slaughterhouse wastewater. Methods and Results: Wastewater samples were spiked with either scrapie or bovine spongiform encephalopathy agents and PrP^res was concentrated and detected by western blotting. The detection limit was estimated to be 2–4 μg of either scrapie or BSE-infected brain tissue in 15 ml of sewage. Wastewater samples from three abattoirs were analysed, two of which had processed BSE-infected animals. No PrP^res was detected. The effect of sewage on the inoculum and the persistence of transmissible spongiform encephalopathy agents in wastewater were also considered. Conclusions: The results of the assay suggest that wastewaters from abattoirs where one positive BSE case has been identified would contain titres lower than 0·6–26 × 10⁻⁴ cattle oral ID₅₀ per litre resulting from specified risk material tissue contamination. Moreover, the effect of abattoir wastewaters is to reduce the persistence of PrP^res. Significance and Impact of the Study: The assay may be a useful tool for risk assessment studies and for reducing the potential risk of contamination with BSE via sewage sludge fertilizer procedures.     

Continuous dechlorination of tetrachloroethene in an upflow anaerobic sludge blanket reactor

Influences of hydraulic retention time (HRT) on dechlorination of tetrachloroethene (PCE) were investigated in an upflow anaerobic sludge blanket (UASB) reactor inoculated with anaerobic granular sludge non-pre-exposed to chlorinated compounds. PCE was introduced into the reactor at a loading rate of 3 mg/l d. PCE removal increased from 51 +/- 5% to 87 +/- 3% when HRT increased from 1 to 4 d, corresponding to an increase in the PCE biotransformation rate from 10.5 +/- 2.3 to 21.3 +/- 3.7 mumol/d. A higher ethene production rate, 0.9 +/- 0.2 mumol/d, was attained without accumulation of dichloroethenes at the HRT of 4 d. Dehalococcoides-like species were detected in sludge granules by fluorescence in situ hybridization, with signal strength in proportion to the extent of PCE dechlorination.     

Evaluation of performance and microbial community in a two-stage UASB reactor pretreating acrylic fiber manufacturing wastewater

A two-stage UASB reactor was employed to pretreat acrylic fiber manufacturing wastewater. Mesophilic operation (35 ± 0.5 °C) was performed with hydraulic retention time (HRT) varied between 28 and 40 h. Mixed liquor suspended solids (MLSS) in the reactor was maintained about 8000 mg/L. The results showed COD and sulfate removal could be kept at 51% and 75%, respectively, when the HRT was no less than 38 h. Sulfate reduction mainly occurred in the acidification-stage reactor while methane production mainly occurred in the methane-stage reactor. The size of granule formed in the acidification-stage reactor ranged between 1 and 5 mm while the largest size of granule in the methane-stage reactor ranged from 0.5 to 2 mm. Compared to microbial populations in the acidification-stage reactor, the microbial diversity in methane-stage reactor was more abundant. In the acidification-stage reactor, the Syntrophobacter sulfatireducens devoted to both sulfate reduction and acetate production.     

Anammox bacteria enrichment in upflow anaerobic sludge blanket (UASB) reactor

We investigated the anaerobic ammonium oxidation (anammox) reaction in a labscale upflow anaerobic sludge blanket (UASB) reactor. Our aim was to detect and enrich the organisms responsible for the anammox reaction using a synthetic medium that contained low concentrations of substrates (ammonium and nitrite). The reactor was inoculated with granular sludge collected from a full-scale anaerobic digestor used for treating brewery wastewater. The experiment was performed during 260 days under conditions of constant ammonium concentration (50 mg NH₄/⁺-N/L) and different nitrite concentrations (50∼150 mg NO₂-N/L). After 200 days, anammox activity was observed in the system. The microorganisms involved in this anammox reaction were identified as CandidatusB. Anammoxidans andK. Stuttgartiensis using fluorescencein situ hybridization (FISH) method.     

The effect of pretreatment on anaerobic activity of olive mill wastewater using batch and continuous systems

This study was focused on several physico-chemical and biological treatment methods that may affect the reduction of the organic load in olive mill wastewater (OMW). In this study, removal of 95% of the phenolic compounds present in OMW was achieved using sand filtration and subsequent treatment with powdered activated carbon in a batch system. This pretreatment for OMW was found to enhance the anaerobic activity of the sludge in the batch system significantly. The efficiency of organic load removal achieved by the anaerobic treatment of untreated OMW in batch reactors with tap water dilution factors below 1:10, reached approximately 65% chemical oxygen demand (COD) removal. However, in the up-flow sludge anaerobic blanket (UASB) reactor, COD removal efficiency of 80–85% was reached at a hydraulic retention time (HRT) of 5 days with an influent COD concentration of 40 g l⁻¹ and organic loading rate (OLR)=8 g⁻¹ COD l⁻¹ per day.     

Start-up of an anaerobic hybrid (UASB/filter) reactor treating wastewater from a coffee processing plant

The ability of an anaerobic hybrid reactor, treating coffee wastewater, to achieve a quick start-up was tested at pilot scale. The unacclimatized seed sludge used showed a low specific methanogenic activity of 26.47 g CH4 as chemical oxygen demand (COD)/kg volatile suspended solids (VSS) x day. This strongly limited the reactor performance. After a few days of operation, a COD removal of 77.2% was obtained at an organic loading rate (OLR) of 1.89 kg COD/m3 x day and a hydraulic retention time (HRT) of 22 h. However, suddenly increasing OLR above 2.4 kg COD/m3 x day resulted in a deterioration in treatment efficiency. The reactor recovered from shock loads after shutdowns of 1 week. The hybrid design of the anaerobic reactor prevented the biomass from washing-out but gas clogging in the packing material was also observed. Wide variations in wastewater strength and flow rates prevented stable reactor operation in the short period of the study.     

Performance of a hybrid anaerobic reactor,combining a sludge blanket and a filter,treating slaughterhouse wastewater

A column reactor, in which the bottom two-thirds were occupied by a sludge blanket and the upper one-third by submerged clay rings, was evaluated using slaughterhouse wastewater as substrate. The reactor was operated at 35°C at loading rates varying from 5 g to 45 g chemical oxygen demand (COD) 1^–1 × day^–1 at an influent concentration of 2450 mg COD 1^–1. A maximum substrate removal rate of 32 g COD 1^–1 × day^–1, coupled with a methane production rate of 6.91 × 1^–1 × day^–1 (STP), was obtained. This removal rate is significantly higher than those previously reported. The rate of substrate utilization by the biomass was 1.22 g COD (g volatile suspended solids)^–1 day^–1. COD removal was over 96% with loading rates up to 25 g COD 1^–1 × day^–1, at higher loading rates performance decreased rapidly. It was found that the filter element of the reactor was highly efficient in retaining biomass, leading to a biomass accumulation yield coefficient of 0.029 g volatile suspended solids g^–1 COD, higher than reported previously for either upflow anaerobic sludge-blanket reactors or anaerobic filters operating independently.     

Experiments and ANFIS modelling for the biodegradation of penicillin-G wastewater using anaerobic hybrid reactor

The performance of an anaerobic hybrid reactor (AHR) for treating penicillin-G wastewater was investigated at the ambient temperatures of 30-35 °C for 245 days in three phases. The experimental data were analysed by adopting an adaptive network-based fuzzy inference system (ANFIS) model, which combines the merits of both fuzzy systems and neural network technology. The statistical quality of the ANFIS model was significant due to its high correlation coefficient R² between experimental and simulated COD values. The R² was found to be 0.9718, 0.9268 and 0.9796 for the I, II and III phases, respectively. Furthermore, one to one correlation among the simulated and observed values was also observed. The results showed the proposed ANFIS model was well performed in predicting the performance of AHR.     

Treatment of coal gasification wastewater by a two-continuous UASB system with step-feed for COD and phenols removal

A two-continuous mesophilic (37 ± 2 °C) UASB system with step-feed was investigated as an attractive optimization strategy for enhancing COD and total phenols removal of the system and improving aerobic biodegradability of real coal gasification wastewater. Through the step-feed period, the maximum removal efficiencies of COD and total phenols reached 55-60% and 58-63% respectively in the system, at an influent flow distribution ratio of 0.2 and influent COD concentration of 2500 mg/L; the corresponding efficiencies were at low levels of 45-50% and 43-50% respectively at total HRT of 48 h during the single-feed period. The maximum specific methanogenic activity and substrate utilization rate were 592 ± 16 mg COD-CH₄/(gVSS d) and 89 ± 12 mg phenol/(gVSS d) during the step-feed operation. After the anaerobic digestion with step-feed, the aerobic effluent COD concentration decreased from 270 ± 9 to 215 ± 10 mg/L. The results suggested that step-feed enhanced the degradation of refractory organics in the second reactor.     

Performance and spatial community succession of an anaerobic baffled reactor treating acetone-butanol-ethanol fermentation wastewater

An anaerobic baffled reactor with four compartments (C1-C4) was successfully used for treatment of acetone-butanol-ethanol fermentation wastewater and methane production. The chemical oxygen demand (COD) removal efficiency was 88.2% with a CH₄ yield of 0.25 L/(g COD_removed) when organic loading rate (OLR) was 5.4 kg COD m⁻³ d⁻¹. C1 played the most important role in solvents (acetone, butanol and ethanol) and COD removal. Community structure of C2 was similar to that in C1 at stage 3 with higher OLR, but was similar to those in C3 and C4 at stages 1-2 with lower OLR. This community variation in C2 was consistent with its increased role in COD and solvent removal at stage 3. During community succession from C1 to C4 at stage 3, abundance of Firmicutes (especially OTUs ABRB07 and ABRB10) and Methanoculleus decreased, while Bacteroidetes and Methanocorpusculum became dominant. Thus, ABRB07 coupled with Methanoculleus and/or acetogen (ABRB10) may be key species for solvents degradation.     

Research on soybean protein wastewater treatment by the integrated two-phase anaerobic reactor

The start-up tests of treating soybean protein wastewater by the integrated two-phase anaerobic reactor were studied. The results showed that the soybean protein wastewater could be successfully processed around 30 days when running under the situation of dosing seed sludge with the influent of approximately 2000 mg/L and an HRT of 40 h. When the start-up was finished, the removal rate of COD by the reactor was about 80%. In the zone I, biogas mainly revealed carbon dioxide (CO₂) and hydrogen (H₂). Methane was the main component in the zone 2 which ranged from 53% to 59% with an average of 55%. The methane content in biogas increased from the zone I to II. It indicated that the methane-producing capacity of the anaerobic sludge increased. It was found that the uniquely designed two-phase integrated anaerobic reactor played a key role in treating soybean protein wastewater. The acidogenic fermentation bacteria dominated in the zone I, while methanogen became dominant in the zone II. It realized the relatively effective separation of hydrolysis acidification and methanogenesis process in the reactor, which was benefit to promote a more reasonable space distribution of the microbial communities in the reactor. There were some differences between the activities of the sludge in the two reaction zones of the integrated two-phase anaerobic reactor. The activity of protease was higher in the reaction zone I. And the coenzyme F₄₂₀ in the reaction zone II was twice than that in the reaction zone I, which indicated that the activity of the methanogens was stronger in the reaction zone II.     

Neutral fat hydrolysis and long-chain fatty acid oxidation during anaerobic digestion of slaughterhouse wastewater

Neutral fat hydrolysis and long-chain fatty acid (LCFA) oxidation rates were determined during the digestion of slaughterhouse wastewater in anaerobic sequencing batch reactors operated at 25 degrees C. The experimental substrate consisted of filtered slaughterhouse wastewater supplemented with pork fat particles at various average initial sizes (D(in)) ranging from 60 to 450 microm. At the D(in) tested, there was no significant particle size effect on the first-order hydrolysis rate. The neutral fat hydrolysis rate averaged 0.63 +/- 0.07 d(-1). LCFA oxidation rate was modelled using a Monod-type equation. The maximum substrate utilization rate (kmax) and the half-saturation concentration (Ks) averaged 164 +/- 37 mg LCFA/L/d and 35 +/- 31 mg LCFA/L, respectively. Pork fat particle degradation was mainly controlled by LCFA oxidation rate and, to a lesser extent, by neutral fat hydrolysis rate. Hydrolysis pretreatment of fat-containing wastewaters and sludges should not substantially accelerate their anaerobic treatment. At a D(in) of 450 microm, fat particles were found to inhibit methane production during the initial 20 h of digestion. Inhibition of methane production in the early phase of digestion was the only significant effect of fat particle size on anaerobic digestion of pork slaughterhouse wastewater. Soluble COD could not be used to determine the rate of lipid hydrolysis due to LCFA adsorption on the biomass.