Effects of fungal pretreatment and steam explosion pretreatment on enzymatic saccharification of plant biomass

The effects of consecutive treatments by a lignin-degrading fungus Phanerochaete chrysosporium and by steam explosion for the enzymatic saccharification of plant biomass were studied experimentally, and the optimal operational conditions for obtaining the maximum saccharification were evaluated. Beech wood-meal was treated by the fungus for 98 days and then by high steam temperatures of 170-230 degrees C with steaming times of 0-10 min. The treatment of the wood-meal by fungus prior to steam explosion enhanced the saccharification of wood-meal. The treated wood-meal was separated into holo-cellulose, water soluble material, methanol soluble lignin, and Klason lignin. The saccharification decreased linearly with the increase in the amount of Klason lignin. It was estimated by the equation for the saccharification of exploded wood-meal expressed as a function of steam temperature and steaming time that the maximum saccharification of wood-meal was obtained by consecutive treatments such as fungal treatment for 28 days and then steam explosion at a steam temperature of 215 degrees C and a steaming time of 6.5 min. (c) 1995 John Wiley & Sons, Inc.     

Ethanol production from paper material using a simultaneous saccharification and fermentation system in a fed-batch basis

In this work, a recycled paper-derived feedstock was used to produce ethanol by the simultaneous saccharification and fermentation (SSF) process using the thermotolerant yeast Kluyveromyces marxianus CECT 10875. At standard SSF conditions, the highest yield (about 80% of theoretical) was obtained at low substrate concentration and high enzyme loading. With increasing substrate concentration, mixing difficulties appeared which prevented an adequate SSF process performance and limited ethanol production. An SSF fed-batch procedure was then used which permitted an increase in substrate concentrations while maintaining SSF yields similar to that obtained at standard SSF, thus allowing an increased final ethanol production (about 18 g/l).     

Acid-catalyzed steam pretreatment of lodgepole pine and subsequent enzymatic hydrolysis and fermentation to ethanol

Utilization of ethanol produced from biomass has the potential to offset the use of gasoline and reduce CO(2) emissions. This could reduce the effects of global warming, one of which is the current outbreak of epidemic proportions of the mountain pine beetle (MPB) in British Columbia (BC), Canada. The result of this is increasing volumes of dead lodgepole pine with increasingly limited commercial uses. Bioconversion of lodgepole pine to ethanol using SO(2)-catalyzed steam explosion was investigated. The optimum pretreatment condition for this feedstock was determined to be 200 degrees C, 5 min, and 4% SO(2) (w/w). Simultaneous saccharification and fermentation (SSF) of this material provided an overall ethanol yield of 77% of the theoretical yield from raw material based on starting glucan, mannan, and galactan, which corresponds to 244 g ethanol/kg raw material within 30 h. Three conditions representing low (L), medium (M), and high (H) severity were also applied to healthy lodgepole pine. Although the M severity conditions of 200 degrees C, 5 min, and 4% SO(2) were sufficiently robust to pretreat healthy wood, the substrate produced from beetle-killed (BK) wood provided consistently higher ethanol yields after SSF than the other substrates tested. BK lodgepole pine appears to be an excellent candidate for efficient and productive bioconversion to ethanol.     

低水用量约束条件下的高固体含量纤维乙醇生物加工技术策略

木质纤维素原料生物转化生产纤维乙醇需要使用大量的水和蒸汽,从而使过程能耗和废水排放显著增加,大幅度增加了加工成本。最大限度地降低水和蒸汽用量对过程节能和废水减排并对最终成本控制极为重要。对极限低水用量约束条件下木质纤维素生物转化关键路径进行了实验研究和计算分析,确定了极低水和蒸汽用量的新型预处理技术,实现高效率预处理过程的废水零排放;采用独特的生物脱毒技术,用从自然界筛选的煤油霉菌Amorphotheca resinae ZN1对预处理原料中的抑制物进行了快速生物脱毒;对极限高固体含量下高粘度多相流物系在复杂抑制物胁迫下的酶水解与发酵行为以及放大准则进行了研究;建立了基于Aspen plus平台上的生物质加工物性数据库和严格热力学意义上的全过程流程模拟数学模型,实现了对过程的局部和全局设计与调优。这一综合技术在生物炼制微型工厂中进行了测试,并在纤维素乙醇工业示范装置中得到了应用。该研究结果将为构建具有工业实用价值的节能和清洁化木质纤维素生物转化技术提供依据。     

Ethanol production from starch by immobilized Aspergillus awamori and Saccharomyces pastorianus using cellulose carriers

A simultaneous saccharification and fermentation (SSF) process was investigated to produce ethanol using two kinds of cellulose carriers that were respectively suitable for immobilization of Aspergillus awamori and Saccharomyces pastorianus. The maximum ethanol concentration attained by the batch operation was 25.5 g l⁻¹. Under suitable conditions, both cellulose carriers with immobilized cells could be reused efficiently for three cycles. The total amount of ethanol production was 66.0 g (per 1 l working volume) after the repeated operation. Ethanol productivity mainly depends on a saccharification process. There is a limit in durability in the repeated batch operation, and it is important to maintain high activity of the fungus in order to produce ethanol efficiently. Journal of Industrial Microbiology & Biotechnology (2001) 27, 52–57. Received 11 December 2000/ Accepted in revised form 02 June 2001     

白腐真菌Pleurotus sajor-caju预处理对红麻秸秆发酵乙醇的影响

为研究微生物法预处理对红麻秸秆中木质素的降解及后续的红麻纤维素酶促糖化和发酵效率的影响,将白腐真菌Pleurotus sajor-caju接种在红麻秸秆培养基上固态培养,对红麻秸秆进行预处理。经P. sajor-caju培养25~35 d后,有效转化红麻秸秆中的木质素,转化率最高可达50.20％,并提高红麻纤维素的酶促水解效率,糖化率达69.33％~78.64％,与对照组相比提高了3.5~4.1倍。以微生物法预处理后的红麻秸秆样品为底物的同步糖化发酵实验表明,发酵72 h,发酵液中乙醇浓度达到18.35~     

响应面法优化耐高温酵母生产高浓度乙醇

利用耐高温酵母GXASY-10菌株对木薯粉同步糖化(SSF)法生产高浓度乙醇的发酵条件进行了优化。在单因素实验的基础上,首先应用Plackett-Burman试验设计筛选影响酒精高温高浓度发酵的重要参数,采用最陡爬坡实验逼近最大酒精生产区域后,利用Box-Behnken设计确定重要参数的最佳水平。筛选结果表明,影响酒精产量的重要参数是液化时间、糖化酶用量和初始木薯粉(底物)浓度。最佳工艺条件为:液化时间为35min,糖化酶添加量为1.21AGU/g底物,底物浓度为37.62%。20L发酵罐在此条件下(发酵温度37℃,转速100r/min)经过48h发酵,酒精浓度可达16.07%(V/W)。优化条件与初始条件相比较,酒精浓度提高了33%。     

马铃薯淀粉同步糖化发酵制备L-乳酸条件的统计学优化

以马铃薯淀粉为原料,采用同步糖化发酵方法制备乳酸。通过Plackett-Burman实验设计对影响乳酸产量的7个因子进行筛选,结果表明淀粉质量浓度、糖化酶用量和发酵温度3个因素对乳酸产量影响显著。利用最陡爬坡试验逼近最大响应区,采用中心复合实验设计及响应面分析法进行回归分析,建立影响乳酸产量的二次模型。模型求解得出最优淀粉质量浓度为271.89g/L,糖化酶用量为265.09U/g,发酵温度为39.05℃,最大理论乳酸产量为196.99g/L。3批验证实验结果平均值与预测值接近,表明该模型与实际情况拟合良好,实际最大乳酸产量为193.6g/L,较优化前提高了13.9%,L-乳酸的平均纯度达到95.2%。     

Ethanol production from paper sludge by simultaneous saccharification and co‐fermentation using recombinant xylose‐fermenting microorganisms

Simultaneous saccharification and co‐fermentation (SSCF) of waste paper sludge to ethanol was investigated using two recombinant xylose‐fermenting microbes: Zymomonas mobilis 8b and Saccharomyces cerevisiae RWB222. S. cerevisiae RWB222 produced over 40 g/L ethanol with a yield of 0.39 g ethanol/g carbohydrate on paper sludge at 37°C, while similar titers and yields were achieved by Z. mobilis 8b at 30°C. Both S. cerevisiae RWB222 and Z. mobilis 8b exhibited decreasing cell viability at 37°C when producing over 40 g/L ethanol. A high ethanol concentration can account for S. cerevisiae RWB222 viability loss, but ethanol concentration was not the only factor influencing Z. mobilis 8b viability loss at 37°C. Over 3 g/L residual glucose was observed at the end of paper sludge SSCF by Z. mobilis 8b, and a statistical analysis revealed that a high calcium concentration originating from paper sludge, a high ethanol concentration, and a high temperature were the key interactive factors resulting in glucose accumulation. The highest ethanol yields were achieved by SSCF of paper sludge with S. cerevisiae RWB222 at 37°C and Z. mobilis 8b at 30°C. With good sugar consumption at 37°C, S. cerevisiae RWB222 was able to gain an improvement in the polysaccharide to sugar yield compared to that at 30°C, whereas Z. mobilis 8b at 30°C had a lower polysaccharide to sugar yield, but a higher sugar to ethanol yield than S. cerevisiae. Both organisms under optimal conditions achieved a 19% higher overall conversion of paper sludge to ethanol than the non‐xylose utilizing S. cerevisiae D5A at its optimal process temperature of 37°C. Biotechnol. Bioeng. 2010;107: 235–244. © 2010 Wiley Periodicals, Inc.     

混合糖发酵重组酿酒酵母的菌株构建和菊芋秸秆同步糖化发酵研究

【目的】构建可用于纤维素乙醇高效生产的混合糖发酵重组酿酒酵母菌株,并利用菊芋秸秆为原料进行乙醇发酵。【方法】筛选在木糖中生长较好的酿酒酵母YB-2625作为宿主菌,构建木糖共代谢菌株YB-2625 CCX。进一步通过r DNA位点多拷贝整合的方式,以YB-2625 CCX为出发菌株构建木糖脱氢酶过表达菌株,并筛选得到优势菌株YB-73。采用同步糖化发酵策略研究YB-73的菊芋秸秆发酵性能。【结果】YB-73菌株以90 g/L葡萄糖和30 g/L木糖为碳源进行混合糖发酵,乙醇产量比出发菌株YB-2625 CCX提高了13.9%,副产物木糖醇产率由0.89 g/g降低至0.31 g/g,下降了64.6%。利用重组菌YB-73对菊芋秸秆进行同步糖化发酵,48 h最高乙醇浓度达到6.10%(体积比)。【结论】通过转入木糖代谢途径以及r DNA位点多拷贝整合过表达木糖脱氢酶基因可有效提高菌株木糖发酵性能,并用于菊芋秸秆的纤维素乙醇生产。这是首次报道利用重组酿酒酵母进行菊芋秸秆原料的纤维素乙醇发酵。     

稀碱预处理棕榈残渣制备纤维乙醇

以棕榈残渣(Empty fruit bunch,EFB)为原料,通过预处理、酶解、发酵等过程制备纤维乙醇.首先对比了碱、碱/过氧化氢等预处理条件对棕榈残渣组成及酶解的影响,结果表明稀碱预处理效果较好.适宜的稀碱预处理条件为:NaOH浓度为1％,固液比为1∶10,在40℃浸泡24 h后于121℃下保温30 min,在该条件下,EFB的固体回收率为74.09％,纤维素、半纤维素和木质素的含量分别为44.08％、25.74％和13.89％.对该条件下预处理后的固体样品,以底物浓度5％、酶载量30 FPU/g底物酶解72 h,纤维素和半纤维素的酶解率分别达到84.44％和89.28％.进一步考察了酶载量和底物浓度对酶解的影响以及乙醇批式同步糖化发酵,当酶载量为30 FPU/g底物,底物浓度由5％增加至25％时,利用酿酒酵母Saccharomyces cerevisiae(接种量为5％,VIV)发酵72 h后乙醇的浓度分别为9.76 g/L和35.25 g/L,可分别达到理论得率的79.09％和56.96％.     

Biological pretreatment of corn stover with Phlebia brevispora NRRL‐13108 for enhanced enzymatic hydrolysis and efficient ethanol production

Biological pretreatment of lignocellulosic biomass by white‐rot fungus can represent a low‐cost and eco‐friendly alternative to harsh physical, chemical, or physico‐chemical pretreatment methods to facilitate enzymatic hydrolysis. In this work, solid‐state cultivation of corn stover with Phlebia brevispora NRRL‐13018 was optimized with respect to duration, moisture content and inoculum size. Changes in composition of pretreated corn stover and its susceptibility to enzymatic hydrolysis were analyzed. About 84% moisture and 42 days incubation at 28°C were found to be optimal for pretreatment with respect to enzymatic saccharification. Inoculum size had little effect compared to moisture level. Ergosterol data shows continued growth of the fungus studied up to 57 days. No furfural and hydroxymethyl furfural were produced. The total sugar yield was 442 ± 5 mg/g of pretreated corn stover. About 36 ± 0.6 g ethanol was produced from 150 g pretreated stover per L by fed‐batch simultaneous saccharification and fermentation (SSF) using mixed sugar utilizing ethanologenic recombinant Eschericia coli FBR5 strain. The ethanol yields were 32.0 ± 0.2 and 38.0 ± 0.2 g from 200 g pretreated corn stover per L by fed‐batch SSF using Saccharomyces cerevisiae D5A and xylose utilizing recombinant S. cerevisiae YRH400 strain, respectively. This research demonstrates that P. brevispora NRRL‐13018 has potential to be used for biological pretreatment of lignocellulosic biomass. This is the first report on the production of ethanol from P. brevispora pretreated corn stover. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:365–374, 2017     

Ethanol production from eucalyptus wood hemicellulose hydrolysate by Pichia stipitis

Ethanol production was evaluated from eucalyptus wood hemicellulose acid hydrolysate using Pichia stipitis NRRL Y-7124. An initial lag phase characterized by flocculation and viability loss of the yeast inoculated was observed. Subsequently, cell regrowth occurred with sequential consumption of sugars and production of ethanol. Polyol formation was detected. Acetic acid present in the hydrolysate was an important inhibitor of the fermentation, reducing the rate and the yield. Its toxic effect was due essentially to its undissociated form. The fermentation was more effective at an oxygen transfer rate between 1.2 and 2.4 mmol/L h and an initial pH of 6.5. The hydrolysate used in the experiences had the following composition (expressed in grams per liter): xylose 30, arabinose 2.8, glucose 1.5, galactose 3.7, mannose 1.0, cellobiose 0.5, acetic acid 10, glucuronic acid 1.5, and galacturonic acid 1.0. The best values obtained were maximum ethanol concentration 12.6 g/L, fermentation time 75 h, fermentable sugar consumption 99% ethanol yield 0.35 g/g sugars consumed, and volumetric ethanol productivity 4 g/L day. (c) 1992 John Wiley & Sons, Inc.     

Process design and optimization of bioethanol production from cassava bagasse using statistical design and genetic algorithm

Abstract

Bioethanol production from agro-industrial residues is gaining attention because of the limited production of starch grains and sugarcane, and food–fuel conflict. The aim of the present study is to maximize the bioethanol production using cassava bagasse as a feedstock. Enzymatic liquefaction, by α-amylase, followed by simultaneous saccharification and fermentation (SSF), using glucoamylase and Zymomonas mobilis MTCC 2427, was investigated for bioethanol production from cassava bagasse. The factors influencing ethanol production process were identified and screened for significant factors using Plackett–Burman design. The significant factors (cassava bagasse concentration (10–50?g/L), concentration of α-amylase (5–25% (v/v), and temperature of fermentation (27–37?°C)) were optimized by employing Box–Behnken design and genetic algorithm. The maximum ethanol concentrations of 25.594?g/L and 25.910?g/L were obtained from Box–Behnken design and genetic algorithm, respectively, under optimum conditions. Thus, the study provides valuable insights in utilizing the cost-effective industrial residue, cassava bagasse, for the bioethanol production.     

响应面法优化玉米秸秆同步酶解发酵产乙醇条件

对汽爆玉米秸秆同步酶解发酵生产乙醇的条件进行优化。首先利用Fractional Factorial设计法对影响乙醇产量的7个因素进行评价,筛选出具有显著效应的3个因素,即反应温度、酶添加量、总反应时间,再以Box—Behnken设计法及响应面分析法确定主要因素的最佳水平,即反应温度37℃,每g纤维素添加纤维素酶32u,反应时间87h,此时乙醇体积分数达到3．69％。新工艺条件实验结果表明,乙醇体积分数在87h可达到3．76％,和原工艺相比,反应时间缩短了9h,乙醇体积分数提高了13％。     

Ethanol production from wheat straw by recombinant Escherichia coli strain FBR5 at high solid loading

Ethanol production by a recombinant bacterium from wheat straw (WS) at high solid loading by separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) was studied. The yield of total sugars from dilute acid pretreated WS (150 g/L) after enzymatic saccharification was 86.3 ± 1.5 g/L. The pretreated WS was bio-abated by growing a fungal strain aerobically in the liquid portion for 16 h. The recombinant Escherichia coli strain FBR5 produced 41.1 ± 1.1 g ethanol/L from non-abated WS hydrolyzate (total sugars, 86.6 ± 0.3 g/L) in 168 h at pH 7.0 and 35 °C. The bacterium produced 41.8 ± 0.0 g ethanol/L in 120 h from the bioabated WS by SHF. It produced 41.6 ± 0.7 g ethanol/L in 120 h from bioabated WS by fed-batch SSF. This is the first report of the production of above 4% ethanol from a lignocellulosic hydrolyzate by the recombinant bacterium.     

Direct production of 4-hydroxybenzoic acid from cellulose using cellulase-displaying Pichia pastoris

4-hydroxybenzoic acid (4-HBA) is an industrially important aromatic compound, and there is an urgent need to establish a bioprocess to produce this compound in a sustainable and environmentally friendly manner from renewable feedstocks such as cellulosic biomass. Here, we developed a bioprocess to directly produce 4-HBA from cellulose using a recombinant Pichia pastoris strain that displays heterologous cellulolytic enzymes on its cell surface via the glycosylphosphatidylinositol (GPI)-anchoring system. β-glucosidase (BGL) from Aspergillus aculeatus, endoglucanase (EG) from Trichoderma reesei, and cellobiohydrolase (CBH) from Talaromyces emersonii were co-displayed on the cell surface of P. pastoris using an appropriate GPI-anchoring domain for each enzyme. The cell-surface cellulase activity was further enhanced using P. pastoris SPI1 promoter- and secretion signal sequences. The resulting strains efficiently hydrolyzed phosphoric acid swollen cellulose (PASC) to glucose. Then, we expressed a highly 4-HBA-resistant chorismate pyruvate-lyase (UbiC) from Providencia rustigianii in the cellulase-displaying strain. This strain produced 975 mg/L of 4-HBA from PASC, which corresponding to 36.8% of the theoretical maximum yield, after 96 h of batch fermentation without the addition of commercial cellulase. This 4-HBA yield was over two times higher than that obtained from glucose (12.3% of the theoretical maximum yield). To our knowledge, this is the first report on the direct production of an aromatic compound from cellulose using cellulase-displaying yeast.     

Impact of an acid fungal protease in high gravity fermentation for ethanol production using indian sorghum as a feedstock

This study evaluated the conventional jet cooking liquefaction process followed by simultaneous saccharification and fermentation (SSF) at 30% and 35% dry solids (DS) concentration of Indian sorghum feedstock for ethanol production, with addition of acid fungal protease or urea. To evaluate the efficacy of thermostable α‐amylase in liquefaction at 30% and 35% DS concentration of Indian sorghum, liquefact solubility, higher dextrins, and fermentable sugars were analyzed at the end of the process. The liquefact was further subjected to SSF using yeast. In comparison with urea, addition of an acid fungal protease during SSF process was observed to accelerate yeast growth (μ), substrate consumption (Q_s), ultimately ethanol yield based on substrate (Y_p/s) and ethanol productivity based on fermentation time (Q_p). The fermentation efficiency and ethanol recovery were determined for both concentrations of Indian sorghum and found to be increased with use of acid fungal protease in SSF process. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 29: 329–336, 2013     

Direct bioconversion of rice residue from canteen waste into lipids by new amylolytic oleaginous yeast Sporidiobolus pararoseus KX709872

The new amylolytic oleaginous red yeast, Sporidiobolus pararoseus KX709872, produced both α-amylase (540?±?0.09?mU/mL) and amyloglucosidase (23?±?0.00?mU/mL) and showed good ability to directly convert rice residue from canteen waste to biomass and lipids. Effects of medium composition and cultivation conditions on growth and lipid accumulation for strain KX709872 were investigated under shaking flask and upscaling levels. At C?:?N ratio of 25?:?1, pH 5.45, 22.36°C, and 199.40?rpm for 7 days, volumetric production of biomass and lipids, lipid content, and lipid productivity reached 17.69?±?0.44, 8.35?±?0.19?g/L, 49.48?±?0.41% (w/w), and 1.67?±?0.11?g/L/day, respectively. Production of lipids was also implemented in 5.0-L stirred tank bioreactor with 2.5?L of optimized medium at 300?rpm and 3.0 vvm for 5 days. Volumetric production of biomass and lipids, lipid content, and lipid productivity were 16.33?±?0.49, 8.75?±?0.13?g/L, 56.61?±?0.04% (w/w), and 2.19?±?0.03?g/L/day, respectively. Meanwhile, the fatty acids of lipids from strain KX709872 had high oleic acid content (60?62%) which was similar to those of vegetable oils, indicating that these lipids are promising as an alternative biodiesel feedstock. Moreover, the biodiesel derived from lipids of strain KX709872 had properties satisfying the criteria of ASTM D6751 and EN 14214 standards.     

Enhanced production of bioethanol from waste of beer fermentation broth at high temperature through consecutive batch strategy by simultaneous saccharification and fermentation

Malt hydrolyzing enzymes and yeast glycolytic and fermentation enzymes in the waste from beer fermentation broth (WBFB) were identified by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). A new ‘one-pot consecutive batch strategy’ was developed for efficient bio-ethanol production by simultaneous saccharification and fermentation (SSF) using WBFB without additional enzymes, microbial cells, or carbohydrates. Bio-ethanol production was conducted in batches using WBFB supernatant in the first phase at 25–67 °C and 50 rpm, followed by the addition of 3% WBFB solid residue to the existing culture broth in the second phase at 67 °C. The ethanol production increased from 50 to 102.5 g/L when bare supernatant was used in the first phase, and then to 219 g ethanol/L in the second phase. The amount of ethanol obtained using this strategy was almost equal to that obtained using the original WBFB containing 25% solid residue at 33 °C, and more than double that obtained when bare supernatant was used. Microscopic and gel electrophoresis studies revealed yeast cell wall degradation and secretion of cellular material into the surrounding medium. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) supported the existence of enzymes in WBFB involved in bioethanol production at elevated temperatures. The results of this study will provide insight for the development of new strategies for biofuel production.