Biomimetic nanofibrous scaffolds: preparation and characterization of chitin/silk fibroin blend nanofibers

Electrospinning of chitin/silk fibroin (SF) blend solutions in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) was investigated to fabricate a biomimetic nanostructured scaffolds for tissue engineering. The morphology of the electrospun chitin/SF blend nanofibers was investigated with a field emission scanning electron microscope (FE-SEM). The average diameters of chitin/SF blend fibers decreased from 920 to 340 nm, with the increase of chitin content in blend compositions. The miscibility of chitin/SF blend fibers was examined by solution viscosity measurement. The chitin and SF were immiscible in the as-spun nanofibrous structure. The dimensional stability of chitin/SF blend nanofibers, with or without water vapor after-treatment, was conducted by immersing in water. As-spun SF-rich blend nanofibrous matrices were lost their fibrous structure after the water immersion for 24 h, and then changed into membrane-like structure. On the contrary, nanofibrous structures of water vapor-treated SF-rich blends were almost maintained. To assay the cytocompatibility and cell behavior on the chitin/SF blend nanofibrous scaffolds, cell attachment and spreading of normal human epidermal keratinocyte and fibroblasts seeded on the scaffolds were studied. Our results indicate that chitin/SF blend nanofibrous matrix, particularly the one that contained 75% chitin and 25% SF, could be a potential candidate for tissue engineering scaffolds because it has both biomimetic three-dimensional structure and an excellent cell attachment and spreading for NHEK and NHEF.     

Effect of chitin/silk fibroin nanofibrous bicomponent structures on interaction with human epidermal keratinocytes

To fabricate a biomimetic nanostructured bicomponent scaffolds, two types of chitin/silk fibroin (SF) nanofibrous scaffolds (blend scaffolds and hybrid scaffolds) were prepared by electrospinning or simultaneous electrospinning of chitin/SF solutions. The chitin/SF bicomponent scaffolds were after-treated with water vapor, and their nanofibrous structures were almost maintained. From the cytocompatibility and cell behavior on the chitin/SF blend or hybrid nanofibrous scaffolds, the hybrid matrix with 25% chitin and 75% SF as well as the chitin/SF blend nanofibers could be a potential candidate for tissue engineering scaffolds.     

Biomimetic nanofibrous scaffolds: preparation and characterization of PGA/chitin blend nanofibers

Electrospinning of poly(glycolic acid) (PGA)/chitin blend solutions in 1,1,1,3,3,3-hexafluoro-2-propanol was investigated to fabricate biodegradable and biomimetic nanostructured scaffolds for tissue engineering. The morphology of the electrospun PGA/chitin blend nanofibers was investigated with a field emission scanning electron microscope. The PGA/chitin blend fibers have average diameters of around 140 nm, and their diameters have a distribution in the range 50-350 nm. The miscibility of PGA/chitin blend fibers was examined by differential scanning calorimetry. The PGA and chitin were immiscible in the as-spun nanofibrous structure. An in vitro degradation study of PGA/chitin blend nanofibers was conducted in phosphate-buffered saline, pH 7.2. It was found that the hydrolytic cleavage of PGA in the blend nanofibers was accelerated by the coexistence of hydrophilic chitin. To assay the cytocompatability and cell behavior on the PGA/chitin blend nanofibrous scaffolds, cell attachment and spreading of normal human epidermal fibroblasts seeded on the scaffolds were studied. Our results indicate that the PGA/chitin blend nanofibrous matrix, particularly the one that contained 25% PGA and 75% chitin with bovine serum albumin coating, could be a good candidate for tissue engineering scaffolds, because it has an excellent cell attachment and spreading for normal human fibroblasts.     

Fabrication and evaluation of poly(epsilon-caprolactone)/silk fibroin blend nanofibrous scaffold

In this study we investigated the blend electrospinning of poly(?‐caprolactone) (PCL) and silk fibroin (SF) to improve the biodegradability and biocompatibility of PCL‐based nanofibrous scaffolds. Optimal conditions to fabricate PCL/SF (50/50) blend nanofiber were established for electrospinning using formic acid as a cosolvent and three‐dimensional (3D) PCL/SF blend nanofibrous scaffolds were prepared by a modified electrospinning process using methanol coagulation bath. The physical properties of 2D PCL/SF blend nanofiber mats and 3D highly porous blend nanofibrous scaffolds were measured and compared. To evaluate cytocompatibility of the 3D blend scaffolds as compared to 3D PCL nanofibrous scaffold, normal human dermal fibroblasts were cultured. It is concluded that biodegradability and cytocompatibility could be improved for the 3D highly porous PCL/SF (50/50) blend nanofibrous scaffold prepared by blending PCL with SF in electrospinning. In addition to the blending of PCL and SF, the 3D structure and high porosity of electrospun nanofiber assemblies may also be important factors for enhancing the performance of scaffolds. © 2011 Wiley Periodicals, Inc. Biopolymers 97: 265–275, 2012.     

Enzymatic degradation of Antheraea pernyi silk fibroin 3D scaffolds and fibers

In this study, the in vitro enzymatic degradation behavior of the regenerated Antheraea pernyi silk fibroin (Ap-SF) three-dimensional (3D) scaffolds and the natural Ap-SF fibers exposed to enzyme solutions of α-chymotrypsin, collagenase IA and protease XIV were investigated. The results indicated that all three proteases could degrade the Ap-SF 3D scaffolds, and the degradation ability was in the order protease XIV>collagenase IA>α-chymotrypsin. The regenerated Ap-SF 3D scaffold could be degraded completely in 18 days when exposed to 1.0 U/ml protease XIV at 37°C, whereas under the same condition, the natural Ap-SF fiber only lost 5.6% of its weight, revealing its long-term degradation characteristics. There were abundant peptides and some free amino acids in the Ap-SF degradation products, but no free alanine. We suggested that the polyalanine block in the regenerated Ap-SF 3D scaffolds had strong resistance to enzyme attack. The proteolytic attack occurred in the non-polyalanine block of Ap-SF. The degradation rate of Ap-SF materials depended on the molecular conformation of Ap-SF, which could be controlled in the manufacturing process.     

小鼠胚胎干细胞结合丝素材料向神经细胞分化的实验研究

以小鼠胚胎干细胞（ES）为种子细胞,使用改良的4-/4+ RA方案,诱导小鼠ES细胞在丝素材料上向神经细胞分化,探讨丝素材料对其生长、黏附、分化等情况的影响。将小鼠ES细胞悬浮培养4 d得到的拟胚体（EBs）分别接种到经丝素膜和明胶包被的培养皿上进行诱导,比较不同材料上EBs的贴壁率及向神经元分化的比率。结果表明EBs在明胶和柞蚕丝素蛋白膜（TSF）上贴壁较快,平均贴壁率为90.3%和84.4%,在桑蚕丝素蛋白膜（SF）上贴壁较慢,贴壁率低,仅为38.5%,同时三者神经元的分化比率均能达到40%以上,无明显差异。通过以上实验,我们得出,TSF有望成为小鼠ES细胞向神经细胞分化的支架材料。     

Preparation, characterization and biocompatibility of electrospinning heparin-modified silk fibroin nanofibers

In this study, the electrospun silk fibroin nanofibrous scaffolds were modified with heparin by grafting after plasma treatment and blending electrospinning. Morphology, microstructure, chemical composition and grafting efficiency of the heparin-modified silk fibroin nanofibrous scaffolds were characterized to evaluate the effect of modification by means of scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR) and X-ray photoelectron spectrometer (XPS). The results showed that the heparin was successfully introduced to the silk fibroin nanofibrous scaffolds by both the two kinds of modification, and there was a hydrogen bonding between the silk fibroin and heparin. Moreover, the hydrophilicity, O-containing groups and negative charge density of the heparin-modified scaffolds were enhanced. In vitro coagulation time tests showed that the activated partial thromboplastin time (APTT), prothrombin time (PT) and thrombin time (TT) of the heparin-modified scaffolds were much higher than those of the pure silk fibroin scaffolds. L929 fibroblasts and EVCs spread and proliferated better on the heparin-modified scaffolds than on the pure silk fibroin scaffolds. Macrophages, neutrophils and lymphocytes were not observed in the heparin-modified scaffolds, which indicated that the modified scaffolds could induce minor inflammation in vivo. The results indicated that the electrospun heparin-modified silk fibroin nanofibrous scaffolds could be considered as ideal candidates for tissue engineering scaffolds.     

一种可止血的富血小板血浆壳聚糖/丝素蛋白多孔伤口敷料的制备及性能表征

为了进一步提高伤口敷料的止血性能,文中在生物相容性良好的壳聚糖溶液中引入含有多种生长因子的人源性富血小板血浆(Humanplatelet-richplasma,hPRP),并加入不同体积比例(1∶1、1∶3、3∶1、1∶0)的丝素蛋白溶液以提高材料的多孔性与止血性,通过冷冻干燥法制备不同配比的hPRP-壳聚糖/丝素蛋白敷料,并将纯壳聚糖敷料作为对照组,研究hPRP和丝素蛋白对敷料的止血性能的影响以及丝素蛋白对PRP中生长因子控制释放的影响。结果表明,在壳聚糖敷料中引入hPRP对敷料的止血性有所提高,但对敷料的多孔结构及吸水率无明显改善,若在hPRP-壳聚糖溶液中按照体积比为1∶1的比例加入丝素蛋白溶液,会得到具有较为均匀的多孔结构的敷料,敷料的孔隙率与吸水率分别可达到86.83%±3.84%与1 474%±114%,且该比例的敷料在快速止血性能上表现优异。此外,加入丝素蛋白与壳聚糖比例为1∶1的PRP敷料能有效减少PRP中生长因子在初始阶段的爆裂释放。因此,含hPRP的壳聚糖/丝素蛋白复合敷料有望成为一种能快速止血且能促进伤口愈合的新型伤口敷料。     

Preparation and characterization of wet spun silk fibroin/poly(vinyl alcohol) blend filaments

Silk fibroin (SF)/poly(vinyl alcohol) (PVA) blend filaments were prepared by a wet spinning process. Regenerated SF and PVA were dissolved in formic acid and the dope solution exhibited good fiber formation in a methanol coagulation bath. Due to the miscibility of SF/PVA in formic acid, the filament had a smooth surface and dense structure with a circular cross-section. The crystalline structure and thermal properties were varied with different SF/PVA ratios. The mechanical properties of the filament were also controlled by blending PVA with SF. Especially, the knot strength of the SF filament, which is a very important suture property, could be significantly improved by blending with PVA.     

Impact of pre-incubation time of silk fibroin scaffolds in culture medium on cell proliferation and attachment

Cell behaviours such as proliferation and attachment can be affected by the length of pre-incubation period of the scaffolds in the culture medium for long term. The aim of this study was to investigate the long term pre-incubation of 3D silk fibroin scaffolds in complete culture medium on cell attachment and proliferation. After the preparation of silk fibroin scaffolds by the technique of freeze drying, the scaffolds were pre-incubated in complete culture medium for 2 d, 6 d or 10 d before apical papilla stem cells (SCAP) seeding. Modifications of the scaffold surface and wettability were examined by FE-SEM and water contact angle, respectively. Results showed a decrease both in roughness and water contact angle as pre-incubation time increases. DNA measurement after 18 h and 10 d cell seeding showed a significant increase of DNA concentration which represents better attachment and proliferation with pre-incubation time increase. Qualitative examination, live&dead assay or H&E staining method after 30 h and 10 d cell seeding respectively, indicated that pre-incubation of scaffolds has time dependent effect on cell proliferation and attachment. This suggests that improvement of cell attachment and proliferation may be mediated by differences in the amount of wettability (decreased water contact angle) after exposure of scaffold to culture medium for long term which, in turn, causes more protein adsorption in the surface of silk fibroin scaffold (decreased roughness).     

The chemical structure and the crystalline structures of Bombyx mori silk fibroin.

Some recent data (i.e. published in the last ten years) on the chemical and crystalline structures of B. mori silk are reviewed. The main emphasis is put on the crystallizable portion of silk fibroin, including its chemical constitution and its molecular conformation (at the crystallographic unit-cell level) in the two crystalline modifications : the beta pleated sheet and the silk I structures. The structural aspects are based on a discussion of X-ray and electron diffraction data, and on conformational energy analyses of a model (Ala-Gly)n polypeptide of silk fibroin.     

Non-bioengineered silk gland fibroin protein: characterization and evaluation of matrices for potential tissue engineering applications

The possibility of using wild non-mulberry silk protein as a biopolymer remains unexplored compared to domesticated mulberry silk protein. One of the main reasons for this was for not having any suitable method of extraction of silk protein fibroin from cocoons and silk glands. In this study non-bioengineered non-mulberry silk gland fibroin protein from tropical tasar silkworm Antheraea mylitta, is regenerated and characterized using 1% (w/v) sodium dodecyl sulfate (SDS). The new technique is important and unique because it uses a mild surfactant for fibroin dissolution and is advantageous over other previous reported techniques using chaotropic salts. Fabricated fibroin films are smooth as confirmed by atomic force microscopy. Circular dichroism spectrometry along with Fourier transformed infrared spectroscopy and X-ray diffraction reveal random coil/alpha-helix conformations in regenerated fibroin which transform to beta-sheets, resulting in crystalline structure and protein insolubility through ethanol treatment. Differential scanning calorimetry shows an increase in glass transition (Tg) temperature and enhanced degradation temperature on alcohol treatment. Enhanced cell attachment and viability of AH927 feline fibroblasts were observed on fibroin matrices. Higher mechanical strength along with controllable water stability of regenerated gland fibroin films make non-mulberry Indian tropical tasar silk gland fibroin protein a promising biomaterial for tissue engineering applications.     

An ESR study of spin-labeled silk fibroin membranes and spin-labeled glucose oxidase immobilized in silk fibroin membranes

This article describes the characteristics of silk fibroin membranes and glucose oxidase, immobilized in membranes as determined by a variety of physical methods, mainly the spin-label electron spin resonance (ESR) method. The properties of membranes insolubilized by different methods, i. e., immersion in 80% methanol aqueous solution, uniaxially drawing by placing on a stretcher, and hydration by placing in a desiccator of 96% relative humidity (RH) for 17 h, are compared. The results are also analyzed in relation to ESR spectra of spin-labeled immobilized glucose oxidase and 4-hydroxy-2,2,6,6-tetramethyl-1-piperidinyloxy as a model of the substrate. It is concluded that the heterogeneous structures of the swollen membranes in water differ locally among membranes insolubilized by different methods, but the immobilized state of the enzyme in such membranes is mostly similar. This is correlated to the fact that the thermal or pH stabilities are essentially same among glucose-oxidase-immobilized silk fibroin membranes insolubilized by different methods.     

Preparation and characterization of novel nanocomposite films formed from silk fibroin and nano-TiO2

This paper describes the synthesis and characterization of new regenerated silk fibroin (SF)/nano-TiO(2) composite films. The preparation method, based on the sol-gel technique using butyl titanate as oxide precursor, could avoid reagglomeration of the prepared nanoparticles. Samples were characterized mainly by X-ray diffraction (XRD), ultra-violet (UV) spectroscopy, atomic force microscopy (AFM), Fourier transform infrared (FT-IR) spectroscopy, and thermogravimetric analysis (TGA). The UV and AFM results indicated that TiO(2) nanoparticles could be well dispersed inside the SF film, and the size of TiO(2) was about 80nm. The XRD and FT-IR analysis implied that the formation of nano-TiO(2) particles may induce the conformational transition of silk fibroin to a typical Silk II structure partly with the increasing of crystallinity in the composite films. Compared to the pure SF films, the mechanical and thermal properties of composite films were improved, and the solubility in water was decreased due to the conformational transition of silk fibroin to Silk II structure.     

Degradation mechanism and control of silk fibroin

Controlling the degradation process of silk is an important and interesting subject in the field of biomaterials. In the present study, silk fibroin films with different secondary conformations and nanostructures were used to study degradation behavior in buffered protease XIV solution. Different from previous studies, silk fibroin films with highest β-sheet content achieved the highest degradation rate in our research. A new degradation mechanism revealed that degradation behavior of silk fibroin was related to not only crystal content but also hydrophilic interaction and then crystal-noncrystal alternate nanostructures. First, hydrophilic blocks of silk fibroin were degraded. Then, hydrophobic crystal blocks that were formerly surrounded and immobilized by hydrophilic blocks became free particles and moved into solution. Therefore, on the basis of the mechanism, which enables the process to be more controllable and flexible, controlling the degradation behavior of silk fibroin without affecting other performances such as its mechanical or hydrophilic properties becomes feasible, and this would greatly expand the applications of silk as a biomedical material.