Compatibilization effect of poly(epsilon-caprolactone)-b-poly(ethylene glycol) block copolymers and phase morphology analysis in immiscible poly(lactide)/poly(epsilon-caprolactone) blends

The miscibility and phase behavior of two stereoisomer forms of poly(lactide) (PLA: poly (L-lactide) (PLLA) and poly(DL-lactide) (PDLLA)) blends with poly(epsilon-caprolactone)-b-poly(ethylene glycol) (PCL-b-PEG) and PCL-b-monomethoxy-PEG (PCL-b-MPEG) block copolymers have been investigated by differential scanning calorimetry (DSC). The DSC thermal behavior of both the blend systems revealed that PLA is miscible with the PEG segment phase of PCL-b-(M)PEG but is still immiscible with its PCL segment phase although PCL was block-copolymerized with PEG. On the basis of these results, PCL-b-PEG was added as a compatibilizer to PLA/PCL binary blends. The improvement in mechanical properties of PLA/PCL blends was achieved as anticipated upon the addition of PCL-b-PEG. In addition, atomic force microscopy (AFM) measurements have been performed in order to study the compositional synergism to be observed in mechanical tests. AFM observations of the morphological dependency on blend composition indicate that PLA/PCL blends are immiscible but compatible to some extent and that synergism of compatibilizing may be maximized in the compositional blend ratio before apparent phase separation and coarsening.     

Crystallization behavior and environmental biodegradability of the blend films of poly(3-hydroxybutyric acid) with chitin and chitosan

Crystallization behavior and environmental biodegradability were investigated for the films of bacterial poly(3-hydroxybutyric acid) (PHB) blends with chitin and chitosan. The blend films showed X-ray diffractive peaks that arose from the PHB crystalline component. It was suggested that the lamellar thickness of the PHB crystalline component in the blends was large enough to show detectable X-ray diffractive peaks, but this was too small to show observable melting endotherm in the DSC thermogram and the crystalline band absorption in the FT-IR spectrum. In the PHB/chitin and PHB/chitosan blends, thermal transition temperatures of PHB amorphous region observed by dynamic mechanical thermal analysis were almost the same as that of neat PHB. Both the PHB/chitin and the PHB/chitosan blend films biodegraded in an environmental medium. Several blend films showed faster biodegradation than the pure-state component polymers.     

Miscibility of bioerodible polyphosphazene/poly(lactide-co-glycolide) blends

We have previously demonstrated the feasibility of blending bioerodible polyphosphazenes with poly(lactide-co-glycolide) (PLGA) to form versatile polymeric materials with altered bioerosion properties. These studies demonstrated the effective neutralization of the acidic degradation products of PLGA by the polyphosphazene hydrolysis products. In the present study, five new polymers of dipeptide polyphosphazenes poly[(ethyl glycinato)x(glycyl-ethyl glycinato)yphosphazene] and novel blends of these polyphosphazenes with poly(lactide-co-glycolide) (PLGA) were synthesized and fabricated. The miscibility was analyzed using differential scanning calorimetry and scanning electron microscopy. Hydrogen bonding within the blends was assessed by attenuated total reflectance infrared spectroscopy. The phosphazene component of the blend contained varying ratios of the glycyl-glycine ethyl ester to the glycine ethyl ester. Poly[(ethyl glycinato)0.5(glycine ethyl glycinato)1.5phosphazene formed completely miscible blends with PLGA (50:50) and PLGA (85:15). This is ascribed to the multiple hydrogen-bonding sites within the side groups of the polyphosphazene. The components of the blend act as plasticizers for each other because a glass transition temperature for each blend was detected at a lower temperature than for each individual polymer. A hydrolysis study showed that unblended solid poly[(ethyl glycinato)0.5(glycyl ethyl glycinato)1.5phosphazene] hydrolyzed in less than 1 week. However, the blends degraded at a slower rate than both parent polymers. This is attributed to the buffering capacity of the polyphosphazene hydrolysis products, which increases the pH of the degradation media from 2.5 to 4, thereby slowing the degradation rate of PLGA.     

Phase structure and enzymatic degradation of poly(L-lactide)/atactic poly(3-hydroxybutyrate) blends: an atomic force microscopy study

Phase structures and enzymatic degradation of poly(l-lactide) (PLLA)/atactic poly(3-hydroxybutyrate) (ata-PHB) blends with different compositions were characterized by using atomic force microscopy (AFM). Differential scanning calorimetry (DSC) thermograms of PLLA/ata-PHB blends with different compositions showed two glass transition temperatures, indicating that the PLLA/ata-PHB blends are immiscible in the melt. Surface morphologies of the thin films for PLLA/ata-PHB blends were determined by AFM. Phase separated morphology was recognized from the AFM topography and phase images. The domain size of the components was dependent on the blend ratio. Enzymatic degradation of the PLLA/ata-PHB blends was performed by using both PHB depolymerase and proteinase K. Either PLLA or ata-PHB domains were eroded depending on the kinds of enzyme. Surface morphologies after enzymatic degradation have revealed the phase structure along the depth direction. Enzymatic adsorption of PHB depolymerase was examined on the surface of PLLA/ata-PHB blends. The enzyme molecules were found on both domains of the binary blends. The larger number of enzyme molecules was found on the PLLA domains relative to those on the ata-PHB domains, suggesting the higher affinity of the enzyme against PLLA domain.     

Morphology control in co-continuous poly(L-lactide)/polystyrene blends: a route towards highly structured and interconnected porosity in poly(L-lactide) materials

Poly(L-lactide) is a biodegradable polymer primarily used in biomedical applications. In this paper, both the microstructure and the region of dual-phase continuity are examined for binary and compatibilized poly(L-lactide)/polystyrene blends (PLLA/PS) prepared by melt mixing. The blends are shown to be completely immiscible with an interfacial tension of 6.1 mN/m. The PS-b-PLLA (24,000-b-28,000) diblock copolymer compatibilizer has an asymmetric effect on the blend. It is effective at compatibilizing 50/50 PLLA/PS blends but is only a marginal emulsifier for blends where PLLA is the dominant matrix. Percent continuity, as estimated by solvent extraction/gravimetry and also torque/composition diagrams clearly indicate an onset of the region of dual-phase continuity at 40-45%PS. It is demonstrated that highly percolated blends of the above materials exist from 40 to 75% PS and 40 to 60% PS for the binary and compatibilized blends, respectively. The scale of the microstructure of the continuous morphology is measured using BET and mercury intrusion porosimetry techniques, after extraction of the PS phase. Both the pore size and extent of continuity can be controlled through composition and interfacial modification. Static annealing of the blend after melt mixing can also be used to substantially increase the pore size of the system. Extraction of the PS phase in the blend, carried out after the above preparation protocols, is a route to generating completely interconnected porosity of highly controlled morphologies (pore size, void volume) in poly(L-lactide) materials. In this study, the pore diameter was controlled from 0.9 to 72 microm for a constant void volume of 45-47%, and the void volume was modified from 35 to 74% depending on the blend composition.     

Physical properties of poly(hydroxybutyrate) and copolymers of hydroxybutyrate and hydroxyvalerate

Abstract The major physical properties of poly(hydroxybutyrate) (PHB) and its copolymers with hydroxyvalerate (PHB/HV) and those of their blends are summarised. Cases of liquid-liquid phase separation in homopolymer copolymer blends are reported and conditions where further phase separation occurs during crystallisation are documented. The crystallinity and degree of comonomer inclusion in the crystallisation of copolymers are described and quantified. It is argued that the mechanism for the inclusion of comonomer units in the crystals is of a kinetic rather than an equilibrium nature.     

Environmental degradation of polyester blends containing atactic poly(3-hydroxybutyrate). Biodegradation in soil and ecotoxicological impact

The degradation of poly[(R,S)-3-hydroxybutyrate], a-PHB, binary blends with natural PHB (n-PHB) and poly(L-lactic acid), PLLA, respectively, has been investigated in soil. In such a natural environment, a-PHB blend component was found to biodegrade. The degradation of a-PHB-containing blends proceeded faster than that of respective plain n-PHB and PLLA. The molecular weight decrease of the n-PHB component was higher, while the same rate of bioerosion of both components was observed for the a-PHB/n-PHB binary blend. For the a-PHB blend with PLLA, the weight loss was accompanied by blend composition changes and the decrease of a-PHB content. However, the PLLA molecular weight decrease was lower in the blend in comparison with the plain PLLA sample. The increase of the number of microorganisms particularly observed for the soil where binary blends were incubated indicates that microbial degradation of a-PHB takes place. The terrestrial plant growth test (cress and barley) demonstrates no environmental toxicity of the materials studied.     

Lipase-catalyzed biodegradation of poly(epsilon-caprolactone) blended with various polylactide-based polymers

Poly(epsilon-caprolactone) was blended with various polylactide-based polymers and processed to films by the solution casting method. Blends of 25/75, 50/50, 75/25, 90/10, and 95/5 (w/w) poly(epsilon-caprolactone)/poly(l-lactide), a 95/5 (w/w) blend of poly(epsilon-caprolactone) with a poly(d-lactide), a 50/50 (w/w) poly(l-lactide)-poly(d-lactide) mixture, and a poly(l-lactide-co-epsilon-caprolactone) copolymer were considered comparatively. The various phase-separated films were allowed to degrade in the presence of Pseudomonas lipase, biodegradation being monitored by proton nuclear magnetic resonance, size exclusion chromatography, differential scanning calorimetry, X-ray diffraction, and environmental scanning electron microscopy. The formation of separated phases during solvent evaporation and their morphologies are discussed. The introduction of poly(l-lactide) dramatically decreased the degradation rate of poly(epsilon-caprolactone)/poly(l-lactide) blends. The higher the percentage of poly(l-lactide), the slower the degradation, while the presence of cracks and increasing the lipase concentration acted in favor of the enzymatic degradation. Long-term enzymatic degradation of the various 95/5 blends was investigated over 480 h. The poly(epsilon-caprolactone) phase was enzymatically degraded by the lipase regardless of the blend type, the degradation rate depending on the nature of the co-components.     

Uniaxial drawing and mechanical properties of poly[(R)-3-hydroxybutyrate]/poly(L-lactic acid) blends

Blends of poly(L-lactic acid) (PLLA) with two kinds of poly[(R)-3-hydroxybutyrate] (PHB) having different molecular weights, commercial-grade bacterial PHB (bacterial-PHB) and ultrahigh molecular weight PHB (UHMW-PHB), were prepared by the solvent-casting method and uniaxially drawn at two drawing temperatures, around PHB's T(g) (2 degrees C) for PHB-rich blends and around PLLA's T(g) (60 degrees C) for PLLA-rich blends. Differential scanning calorimetry analysis showed that this system was immiscible over the entire composition range. Mechanical properties of all of the samples were improved in proportion to the draw ratio. Although PLLA domains in bacterial-PHB-rich blends remained almost unstretched during cold drawing, a good interfacial adhesion between two polymers and the reinforcing role of PLLA components led to enhanced mechanical properties proportionally to the PLLA content at the same draw ratio. On the contrary, in the case of UHMW-PHB-rich blends, the minor component PLLA was found to be also oriented by cold drawing in ice water due to an increase in the interfacial entanglements caused by the very long chain length of the matrix polymer. As a result, their mechanical properties were considerably improved with increasing PLLA content compared with the bacterial-PHB system. Scanning electron microscopy observations on the surface and cross-section revealed that a layered structure with uniformly oriented microporous in the interior was obtained by selectively removal of PLLA component after simple alkaline treatment.     

Compatible ternary blends of chitosan/poly(vinyl alcohol)/poly(lactic acid) produced by oil-in-water emulsion processing

Ternary compatible blends of chitosan, poly(vinyl alcohol), and poly(lactic acid) were prepared by an oil-in-water (O/W) emulsion process. Solutions of chitosan in aqueous acetic acid, poly(vinyl alcohol) (PVA) in water, and poly(lactic acid) (PLA) in chloroform were blended with a high-shear mixer. PVA was used as an emulsifier to stabilize the emulsion and to reduce the interfacial tension between the solid polymers in the blends produced. It proved to work very well because the emulsions were stable for periods of days or weeks and compatible blends were obtained when PVA was added. This effect was attributed to a synergistic effect of PVA and chitosan because the binary blends PVA/PLA and chitosan/PLA were completely incompatible. The blends were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermal mechanical analysis (TMA), stress-strain tests, and Fourier transform infrared spectroscopy (FTIR). The results indicated that despite the fact that the system contained distinct phases some degree of molecular miscibility occurred when the three components were present in the blend.     

Blend miscibility of cellulose propionate with poly(N-vinyl pyrrolidone-co-methyl methacrylate)

The blend miscibility of cellulose propionate (CP) with poly(N-vinyl pyrrolidone-co-methyl methacrylate) (P(VP-co-MMA)) was investigated. The degree of substitution (DS) of CP used ranged from 1.6 to >2.9, and samples for the vinyl polymer component were prepared in a full range of VP:MMA compositions. Through DSC analysis and solid-state ¹³C NMR and FT-IR measurements, we revealed that CPs of DS < 2.7 were miscible with P(VP-co-MMA)s of VP ≥ ∼10 mol% on a scale within a few nanometers, in virtue of hydrogen-bonding interactions between CP-hydroxyls and VP-carbonyls. When the DS of CP exceeded 2.7, the miscibility was restricted to the polymer pairs using P(VP-co-MMA)s of VP = ca. 10–40 mol%; the scale of mixing in the blends concerned was somewhat larger (ca. 5–20 nm), however. The appearance of such a “miscibility window” was interpretable as an effect of intramolecular repulsion in the copolymer component. Results of DMA and birefringence measurements indicated that the miscible blending of CP with the vinyl polymer invited synergistic improvements in thermomechanical and optical properties of the respective constituent polymers. Additionally, it was found that the VP:MMA composition range corresponding to the miscibility window was expanded by modification of the CP component into cellulose acetate propionate.     

Design of mucoadhesive polymeric films based on blends of poly(acrylic acid) and (hydroxypropyl)cellulose

Mixing of aqueous solutions of poly(acrylic acid) and (hydroxypropyl)cellulose results in formation of hydrogen-bonded interpolymer complexes, which precipitate and do not allow preparation of homogeneous polymeric films by casting. In the present work the effect of pH on the complexation between poly(acrylic acid) and (hydroxypropyl)cellulose in solutions and miscibility of these polymers in solid state has been studied. The pH-induced complexation-miscibility-immiscibility transitions in the polymer mixtures have been observed. The optimal conditions for preparation of homogeneous polymeric films based on blends of these polymers have been found, and the possibility of radiation cross-linking of these materials has been demonstrated. Although the gamma-radiation treatment of solid polymeric blends was found to be inefficient, successful cross-linking was achieved by addition of N,N'-methylenebis(acrylamide). The mucoadhesive potential of both soluble and cross-linked films toward porcine buccal mucosa is evaluated. Soluble films adhered to mucosal tissues undergo dissolution within 30-110 min depending on the polymer ratio in the blend. Cross-linked films are retained on the mucosal surface for 10-40 min and then detach.     

Critical Role of Polymer Aggregation and Miscibility in Nonfullerene‐Based Organic Photovoltaics

Understanding the correlation between polymer aggregation, miscibility, and device performance is important to establish a set of chemistry design rules for donor polymers with nonfullerene acceptors (NFAs). Employing a donor polymer with strong temperature‐dependent aggregation, namely PffBT4T‐2OD [poly[(5,6‐difluoro‐2,1,3‐benzothiadiazol‐4,7‐diyl)‐alt‐(3,3″′‐di(2‐octyldodecyl)‐2,2′;5′,2″;5″,2″′‐quaterthiophen‐5,5‐diyl)], also known as PCE‐11 as a base polymer, five copolymer derivatives having a different thiophene linker composition are blended with the common NFA O‐IDTBR to investigate their photovoltaic performance. While the donor polymers have similar optoelectronic properties, it is found that the device power conversion efficiency changes drastically from 1.8% to 8.7% as a function of thiophene content in the donor polymer. Results of structural characterization show that polymer aggregation and miscibility with O‐IDTBR are a strong function of the chemical composition, leading to different donor–acceptor blend morphology. Polymers having a strong tendency to aggregate are found to undergo fast aggregation prior to liquid–liquid phase separation and have a higher miscibility with NFA. These properties result in smaller mixed donor–acceptor domains, stronger PL quenching, and more efficient exciton dissociation in the resulting cells. This work indicates the importance of both polymer aggregation and donor–acceptor interaction on the formation of bulk heterojunctions in polymer:NFA blends.     

Hydrogen bonding in stereoregular poly(methyl methacrylate)/poly(vinyl chloride) blends as studied by molecular dynamics simulations

In this work, two technically important polymer blends composed of isotactic poly (methyl methacrylate) (iPMMA) or syndiotactic poly (methyl methacrylate) (sPMMA) and isotactic poly (vinyl chloride) (iPVC) have been extensively investigated by molecular dynamics simulations. It is confirmed that sPMMA exhibits stronger interactions with iPVC than does iPMMA, and the non-conventional hydrogen bonds (HBs) occur between the two distinct components. Furthermore, the HBs in sPMMA/iPVC are more than those in iPMMA/iPVC, and the structural relaxation of HBs is closely associated with the backbone chain dynamics, which well explain the experimental trends in miscibility of the two systems and in glass transition temperature of single components. It should be noted that these results cannot be directly obtained by the experiments and single simulations, and the multiscale schemes used to prepare the initial all-atomistic configurations can play an important role. This work provides some key clues to improve the performance of polymer materials.     

Blends of aliphatic polyesters. VI. Lipase-catalyzed hydrolysis and visualized phase structure of biodegradable blends from poly(epsilon-caprolactone) and poly(L-lactide)

Phase-separated biodegradable polymer blends were prepared from poly(epsilon-caprolactone) (PCL) and poly(L-lactide) (PLLA), and Rhizopus arrhizus lipase-catalyzed hydrolysis and phase structure of the blend films were investigated. Gravimetry revealed that the lipase-catalyzed hydrolysis of PCL in PCL- and PLLA-rich phases is disturbed by the presence of PLLA. Polarimetry confirmed the occurrence of a predominant hydrolysis of PCL and subsequent removal of the hydrolyzed water-soluble PCL oligomers in the blend films. Gravimetry and gel permeation chromatography of the non-blended PLLA film indicated that R. arrhizus lipase has no catalytic effect on the hydrolysis of PLLA. The phase structure of the blend films could be visualized by selective enzymatic removal of one component and subsequent scanning electron microscopic observation.     

Microbial communities responsible for the degradation of poly(lactic acid)/poly(3-hydroxybutyrate) blend mulches in soil burial respirometric tests

The microbial communities responsible for the degradation of poly(lactic acid)/poly(3-hydroxybutyrate) (PLA/PHB) blend foils were investigated in 1 year long laboratory soil burial experiments. Different PLA/PHB foils were tested: (a) PLA/PHB original transparent foil, (b) PLA/PHB carbon black filled foil and (c) PLA/PHB black foil previously exposed for 90 days to sun light. The microbiome diversity of these three types of foil was compared with that identified from soil/perlite sample at the beginning of experiment and that developed on a cellulose mat. Culture-dependent and culture-independent (DGGE-cloning) approaches together with PLA, PHB and PLA/PHB degradation plate assays were employed. The cultivation strategy combined with degradation tests permitted the isolation and evaluation of several PLA/PHB blend degrading microorganisms such as members of the genera Bacillus, Paenibacillus, Streptomyces, Rhodococcus, Saccharothrix, Arthrobacter, Aureobasidium, Mortierella, Absidia, Actinomucor, Bjerkandera, Fusarium, Trichoderma and Penicillium. The DGGE-cloning investigation increased the information about the microbial communities occurring during bioplastic degradation detecting several bacterial and fungal taxa and some of them (members of the orders Anaerolineales, Selenomonadales, Thelephorales and of the genera Pseudogymnoascus and Pseudeurotium) were revealed here for the first time. This survey showed the microbiome colonizing PLA/PHB blend foils and permitted the isolation of several microorganisms able to degrade the tested polymeric blends.     

A study of conformational stability of poly(L-alanine), poly(L-valine), and poly(L-alanine)/poly(L-valine) blends in the solid state by (13)C cross-polarization/magic angle spinning NMR

13C cross-polarization/magic angle spinning (CP/MAS) NMR and (1)H T(1rho) experiments of poly(L-alanine) (PLA), poly(L-valine) (PLV), and PLA/PLV blends have been carried out in order to elucidate the conformational stability of the polypeptides in the solid state. These were prepared by adding a trifluoroacetic acid (TFA) solution of the polymer with a 2.0 wt/wt % of sulfuric acid (H(2)SO(4)) to alkaline water. From these experimental results, it is clarified that the conformations of PLA and PLV in their blends are strongly influenced by intermolecular hydrogen-bonding interactions that cause their miscibility at the molecular level.     

A molecular simulation of the compatibility of chitosan and poly(vinyl pyrrolidone)

The compatibility of chitosan (CS) and poly(vinyl pyrrolidone) was investigated by molecular dynamic (MD) simulations using the Flory–Huggins theory. The specific interactions in blends were studied by the radial distribution function (RDF). The Flory–Huggins interaction parameter, χ, was calculated at 298 K to assess the blend compatibility at different component ratios in the polymers. Miscibility was observed for blends with more than 50% of CS in the molar fraction, while immiscibility was prevalent at the molar fraction of CS between 10 and 50% of CS. Miscibility between poly(N-vinyl-2-pyrrolidone) (PVP) and CS polymers is attributed to the hydrogen bond formation of the –C = O group of PVP and the –CH₂OH groups of CS. This was further confirmed by MD simulations of RDFs for groups or atoms that are involved in interactions. These results are correlated well to obtain more realistic information on interactions involved as a function of blend composition.     

Wheat gluten-thiolated poly(vinyl alcohol) blends with improved mechanical properties

A multifunctional macromolecular thiol (TPVA) obtained by esterification of poly(vinyl alcohol) (PVA) with 3-mercaptopropionic acid was characterized by a combination of NMR, IR, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC), and was used as a wheat gluten (WG) reactive modifier. The effect of TPVA molecular weight (M(w) = 2000, 9500, 50 000, and 205 000) and blend composition (5, 20, and 40% w/w TPVA/WG) on the mechanical properties of compression-molded bars indicates that TPVA/WG blends increase the fracture strength by up to 76%, the elongation by 80%, and the modulus by 25% above WG. In contrast, typical WG additives such as glycerol and sorbitol improve flexibility but decrease modulus and strength. Preliminary investigations of suspension rheology, water uptake, molecular weight distribution and electron microscopy of TPVA/WG and PVA/WG blends illustrate the different protein interactions with PVA and TPVA. Further work is underway to determine whether TPVA and WG form protein conjugates or microphase-separated morphologies.     

Carboxylate-induced degradation of poly(3-hydroxybutyrate)s

This communication shows that thermal degradation of poly(3-hydroxybutyrate)s (PHBs) is induced by carboxylate groups via a newly proposed E1cB mechanism. In PHBs with end groups in the form of carboxylic acid salts with Na+, K+, and Bu4N+ counterions, the proposed mechanism explains the dependence of thermal stability on the size of the counterion. The degradation via intermolecular alpha-deprotonation by carboxylate is suggested to be the main PHB decomposition pathway at moderate temperatures. The results of the present study show the ability to control the degradation and stability of poly(3-hydroxybutyrate)s as well as of their blends via chemical structure and concentration of the carboxylate polymer end groups.