Ethanol production from syngas by Clostridium strain P11 using corn steep liquor as a nutrient replacement to yeast extract

The feasibility of replacing yeast extract (YE) by corn steep liquor (CSL), a low cost nutrient source, for syngas fermentation to produce ethanol using Clostridium strain P11 was investigated. About 32% more ethanol (1.7 g L⁻¹) was produced with 20 g L⁻¹ CSL media in 250-mL bottle fermentations compared to media with 1 g L⁻¹ YE after 360 h. Maximum ethanol concentrations after 360 h of fermentation in a 7.5-L fermentor with 10 and 20 g L⁻¹ CSL media were 8.6 and 9.6 g L⁻¹, respectively, which represent 57% and 60% of the theoretical ethanol yields from CO. Only about 6.1 g L⁻¹ of ethanol was obtained in the medium with 1 g L⁻¹ YE after 360 h, which represents 53% of the theoretical ethanol yield from CO. The use of CSL also enhanced butanol production by sevenfold compared to YE in bottle fermentations. These results demonstrate that CSL can replace YE as the primary medium component and significantly enhance ethanol production by Clostridium strain P11.     

Optimization of a corn steep medium for production of ethanol from synthesis gas fermentation by <Emphasis Type="Italic">Clostridium ragsdalei</Emphasis>

Fermentation of biomass derived synthesis gas to ethanol is a sustainable approach that can provide more usable energy and environmental benefits than food-based biofuels. The effects of various medium components on ethanol production by Clostridium ragsdalei utilizing syngas components (CO:CO₂) were investigated, and corn steep liquor (CSL) was used as an inexpensive nutrient source for ethanol production by C. ragsdalei. Elimination of Mg²⁺, NH₄ ⁺ and PO₄ ³⁻ decreased ethanol production from 38 to 3.7, 23 and 5.93 mM, respectively. Eliminating Na⁺, Ca²⁺, and K⁺ or increasing Ca²⁺, Mg²⁺, K⁺, NH₄ ⁺ and PO₄ ³⁻ concentrations had no effect on ethanol production. However, increased Na⁺ concentration (171 mM) inhibited growth and ethanol production. Yeast extract (0.5 g l⁻¹) and trace metals were necessary for growth of C. ragsdalei. CSL alone did not support growth and ethanol production. Nutrients limiting in CSL were trace metals, NH₄ ⁺ and reducing agent (Cys: cysteine sulfide). Supplementation of trace metals, NH₄ ⁺ and CyS to CSL (20 g l⁻¹, wet weight basis) yielded better growth and similar ethanol production as compared to control medium. Using 10 g l⁻¹, the nutritional limitation led to reduced ethanol production. Higher concentrations of CSL (50 and 100 g l⁻¹) were inhibitory for cell growth and ethanol production. The CSL could replace yeast extract, vitamins and minerals (excluding NH₄ ⁺). The optimized CSL medium produced 120 and 50 mM of ethanol and acetate, respectively. The CSL could provide as an inexpensive source of most of the nutrients required for the syngas fermentation, and thus could improve the economics of ethanol production from biomass derived synthesis gas by C. ragsdalei.     

Techno-economic implications of improved high gravity corn mash fermentation

The performance of Saccharomyces cerevisiae MBG3964, a strain able to tolerate >18% v/v ethanol, was compared to leading industrial ethanol strain, Fermentis Ethanol Red, under high gravity corn mash fermentation conditions. Compared to the industrial ethanol strain, MBG3964 gave increased alcohol yield (140 g L⁻¹ vs. 126 g L⁻¹), lower residual sugar (4 g L⁻¹ vs. 32 g L⁻¹), and lower glycerol (11 g L⁻¹ vs. 12 g L⁻¹). After 72 h fermentation, MBG3964 showed about 40% viability, whereas the control yeast was only about 3% viable. Based on modelling, the higher ethanol tolerant yeast could increase the profitability of a corn-ethanol plant and help it remain viable through higher production, lower unit heating requirements and extra throughput. A typical 50 M gal y⁻¹ dry mill ethanol plant that sells dried distiller’s grain could potentially increase its profit by nearly $US3.4 M y⁻¹ due solely to the extra yield, and potentially another $US4.1 M y⁻¹ if extra throughput is possible.     

Effect of temperature, pH and buffer presence on ethanol production from synthesis gas by "Clostridium ragsdalei"

Fermentation pH, incubation temperature, and presence or absence of media buffer can alter the activity of microorganisms. For instance, carbon monoxide and hydrogen components of syngas show decreased solubility with increasing temperature, Clostridium species preferentially switch from acetogenesis to solventogenesis phase at pH below 5.0, and morpholinoethanesulfonic acid (MES) added as media buffer has been shown to increase lag time for ethanol production. The objective of the present study was to determine the effects of temperature, pH and MES buffer on ethanol production by “Clostridium ragsdalei”. This study showed syngas fermentation using “Clostridium ragsdalei” at 32 °C with media without buffer was associated with higher ethanol concentration and reduced lag time in switching to solventogenesis. Temperature above 40 °C and pH below 5.0 were outside the optimal range for growth and metabolism of the bacteria.     

Enhanced ethanol production from sugarcane juice by galactose adaptation of a newly isolated thermotolerant strain of Pichia kudriavzevii

The thermotolerant yeast strain isolated from sugarcane juice through enrichment technique was identified as a strain of Pichiakudriavzevii (Issatchenkiaorientalis) through molecular characterization. The P. kudriavzevii cells adapted to galactose medium produced about 30% more ethanol from sugarcane juice than the non-adapted cells. The recycled cells could be used for four successive cycles without a significant drop in ethanol production. Fermentation in a laboratory fermenter with galactose adapted P. kudriavzevii cells at 40 °C resulted in an ethanol concentration and productivity of 71.9 g L⁻¹ and 4.0 g L⁻¹ h⁻¹, respectively from sugarcane juice composed of about 14% (w/v) sucrose, 2% (w/v) glucose and 1% (w/v) fructose. In addition to ethanol, 3.30 g L⁻¹ arabitol and 4.19 g L⁻¹ glycerol were also produced, whereas sorbitol and xylitol were not formed during fermentation. Use of galactose adapted P. kudriavzevii cells for ethanol production from sugarcane juice holds potential for scale-up studies.     

Biological treatment of eucalypt spent sulphite liquors: a way to boost the production of second generation bioethanol

The fermentation of reducing sugars from hardwood (eucalypt) spent sulphite liquor (HSSL) into ethanol by Pichia (Scheffersomyces) stipitis is hindered by concomitant inhibitors of microbial metabolism. The conditions for the HSSL biological treatment step by Paecilomyces variotii were evaluated and optimised. Two different strategies of reactor operation were compared using single batch (B) and sequential batch reactor (SBR). Biological treatment of HSSL in the SBR revealed the best results with respect to the removal of microbial inhibitors. Also, most of inhibitory compounds, acetic acid, gallic acid, pyrogallol, amongst others, were removed from HSSL by P. variotii before the ethanol fermentation. The bio-detoxified HSSL was subjected to a successful fermentation by P. stipitis, attaining a maximum ethanol concentration of 2.4 g L⁻¹ with a yield of 0.24 g ethanol g sugars⁻¹.     

pH-control modes in a 5-L stirred-tank bioreactor for cell biomass and exopolysaccharide production by Tremella fuciformis spore

The effect of pH-control modes on cell growth and exopolysaccharide production by Tremella fuciformis was evaluated in a 5-L bioreactor. The results show that the maximal dry cell weight (DCW) and exopolysaccharide production were 23.57 and 4.48 g L⁻¹ in pH-stat fermentation, where the maximal specific growth rate (μ_max) and specific production rate of exopolysaccharide (P_P/X) were 1.03 and 0.24 d⁻¹, respectively; under pH-shift cultivation, the maximal DCW and exopolysaccharide production were 30.57 and 3.90 g L⁻¹, where the μ_max and P_P/X were 1.21 and 0.06 d⁻¹. Unlike batch fermentation, maximal DCW and exopolysaccharide production merely reached 15.04 and 2.0 g L⁻¹, where the μ_max and P_P/X were 0.86 and 0.05 d⁻¹, respectively. These results suggest that a pH-stat strategy is a more efficient way of performing the fermentation process to increase exopolysaccharide production. Furthermore, this research has also proved that the three-stage pH-control mode is effective for cell growth.     

Enhanced ethanol production by fermentation of rice straw hydrolysate without detoxification using a newly adapted strain of Pichia stipitis

An enhanced inhibitor-tolerant strain of Pichia stipitis was successfully developed through adaptation to acid-treated rice straw hydrolysate. The ethanol production obtained by fermentation of NaOH-neutralized hydrolysate without detoxification using the adapted P. stipitis was comparable to fermentation of overliming-detoxified hydrolysate. The ethanol yield using the adapted P. stipitis with both types of hydrolysate at pH 5.0 achieved 0.45 g_p g_s⁻¹, which is equivalent to 87% of the maximum possible ethanol conversion. Furthermore, the newly adapted P. stipitis demonstrated significantly enhanced tolerance to sulfate and furfural despite the fact that both inhibitors had not been removed from the hydrolysate by NaOH neutralization. Finally, the ethanol conversion could be maintained at 60% and above when the neutralized hydrolysate contained 3.0% sulfate and 1.3 g L⁻¹ furfural.     

Ethanol production from sweet sorghum juice using very high gravity technology: Effects of carbon and nitrogen supplementations

Ethanol production from sweet sorghum juice by Saccharomyces cerevisiae NP01 was investigated under very high gravity (VHG) fermentation and various carbon adjuncts and nitrogen sources. When sucrose was used as an adjunct, the sweet sorghum juice containing total sugar of 280 g l⁻¹, 3 g yeast extract l⁻¹ and 5 g peptone l⁻¹ gave the maximum ethanol production efficiency with concentration, productivity and yield of 120.68 ± 0.54 g l⁻¹, 2.01 ± 0.01 g l⁻¹ h⁻¹ and 0.51 ± 0.00 g g⁻¹, respectively. When sugarcane molasses was used as an adjunct, the juice under the same conditions gave the maximum ethanol concentration, productivity and yield with the values of 109.34 ± 0.78 g l⁻¹, 1.52 ± 0.01 g l⁻¹ h⁻¹ and 0.45 ± 0.01 g g⁻¹, respectively. In addition, ammonium sulphate was not suitable for use as a nitrogen supplement in the sweet sorghum juice for ethanol production since it caused the reduction in ethanol concentration and yield for approximately 14% when compared to those of the unsupplemented juices.     

Lactic acid production by Lactobacillus sp. RKY2 in a cell-recycle continuous fermentation using lignocellulosic hydrolyzates as inexpensive raw materials

Continuous lactic acid fermentations were conducted using lignocellulosic hydrolyzates and corn steep liquor as inexpensive raw materials. Lactic acid concentrations decreased with increases in the dilution rate, whereas the residual substrate concentrations increased. However, lactic acid yields were maintained at more than 0.90 g g⁻¹ over all cases experimented. The cell-recycle cultivation system exerted positive effects on fermentation efficiency, including volumetric productivity, which is attributable to the retention of cells in the bioreactor. The cell-recycle continuous fermentation of lignocellulosic hydrolyzates yielded a lactic acid productivity of 6.7 g l⁻¹ h⁻¹ for a dilution rate of 0.16 h⁻¹ using 30 g l⁻¹ of corn steep liquor and 1.5 g l⁻¹ of yeast extract as nutrients. The productivity (6.7 g l⁻¹ h⁻¹) acquired by the cell-recycle continuous fermentation of lignocellulosic hydrolyzates was 1.6 times higher than the lactic acid productivity yielded in the continuous fermentation without cell-recycle system.     

Bioethanol fermentation of concentrated rice straw hydrolysate using co-culture of Saccharomyces cerevisiae and Pichia stipitis

Rice straw is one of the abundant lignocellulosic feed stocks in the world and has been selected for producing ethanol at an economically feasible manner. It contains a mixture of sugars (hexoses and pentoses).Biphasic acid hydrolysis was carried out with sulphuric acid using rice straw. After acid hydrolysis, the sugars, furans and phenolics were estimated. The initial concentration of sugar was found to be 16.8 g L⁻¹. However to increase the ethanol yield, the initial sugar concentration of the hydrolysate was concentrated to 31 g L⁻¹ by vacuum distillation. The concentration of sugars, phenols and furans was checked and later detoxified by over liming to use for ethanol fermentation. Ethanol concentration was found to be 12 g L⁻¹, with a yield, volumetric ethanol productivity and fermentation efficiency of 0.33 g L⁻¹ h⁻¹, 0.4 g g⁻¹ and 95%, respectively by co-culture of OVB 11 (Saccharomyces cerevisiae) and Pichia stipitis NCIM 3498.     

3-Phenyllactic acid production by substrate feeding and pH-control in fed-batch fermentation of Lactobacillus sp. SK007

3-Phenyllactic acid (PLA), which is produced by some strains of lactic acid bacteria (LAB), is a known antimicrobial agent with a broad spectrum. Batch and fed-batch fermentation by the strain Lactobacillus sp. SK007 for PLA production have been reported. With batch fermentation without pH-control, PLA production yield was 2.42 g L⁻¹. When fed-batch fermentation by Lactobacillus sp. SK007 was conducted in 3 L initial volume with pH-control at 6.0 and intermittent feeding, which was developed after fermentation for 12 h and every 2 h with 120 mL 100 g L⁻¹ PPA phenylpyruvic acid (PPA) and 50 mL 500 g L⁻¹ glucose each time, PLA production yield reached 17.38 g L⁻¹. The final conversion ratio of PPA to PLA was 51.1%, and the PLA production rate was 0.241 g L⁻¹ h⁻¹. This indicated that PPA was the ideal substrate for PLA fermentation production, and fed-batch fermentation with intermittent PPA feeding and pH-control was an effective approach to improve PLA production yield.     

Butyric acid fermentation in a fibrous bed bioreactor with immobilized Clostridium tyrobutyricum from cane molasses

Butyrate fermentation by immobilized Clostridium tyrobutyricum was successfully carried out in a fibrous bed bioreactor using cane molasses. Batch fermentations were conducted to investigate the influence of pH on the metabolism of the strain, and the results showed that the fermentation gave a highest butyrate production of 26.2 g l⁻¹ with yield of 0.47 g g⁻¹ and reactor productivity up to 4.13 g l⁻¹ h⁻¹ at pH 6.0. When repeated-batch fermentation was carried out, long-term operation with high butyrate yield, volumetric productivity was achieved. Several cane molasses pretreatment techniques were investigated, and it was found that sulfuric acid treatment gave better results regarding butyrate concentration (34.6 ± 0.8 g l⁻¹), yield (0.58 ± 0.01 g g⁻¹), and sugar utilization (90.8 ± 0.9%). Also, fed-batch fermentation from cane molasses pretreated with sulfuric acid was performed to further increase the concentration of butyrate up to 55.2 g l⁻¹.     

Enhanced 2,3-butanediol production by Klebsiella oxytoca using a two-stage agitation speed control strategy

Batch fermentative production of 2,3-butanediol by Klebsiella oxytoca was investigated using various oxygen supply methods though varying agitation speed. Based on the analysis of three kinetic parameters including specific cell growth rate (μ), specific glucose consumption rate (q_s) and specific 2,3-butanediol formation rate (q_p), a two-stage agitation speed control strategy, aimed at achieving high concentration, high yield and high productivity of 2,3-butanediol, was proposed. At the first 15 h, agitation speed was controlled at 300 rpm to obtain high μ for cell growth, subsequently agitation speed was controlled at 200 rpm to maintain high q_p for high 2,3-butanediol accumulation. Finally, the maximum concentration of 2,3-butanediol reached 95.5 g l⁻¹ with the yield of 0.478 g g⁻¹ and the productivity of 1.71 g l⁻¹ h⁻¹, which were 6.23%, 6.22% and 22.14% over the best results controlled by constant agitation speeds.     

Effect of lignocellulosic inhibitory compounds on growth and ethanol fermentation of newly-isolated thermotolerant Issatchenkia orientalis

A newly isolated thermotolerant ethanologenic yeast strain, Issatchenkia orientalis IPE 100, was able to produce ethanol with a theoretical yield of 85% per g of glucose at 42 °C. Ethanol production was inhibited by furfural, hydroxymethylfurfural and vanillin concentrations above 5.56 g L⁻¹, 7.81 g L⁻¹, and 3.17 g L⁻¹, respectively, but the strain was able to produce ethanol from enzymatically hydrolyzed steam-exploded cornstalk with 93.8% of theoretical yield and 0.91 g L⁻¹ h⁻¹ of productivity at 42 °C. Therefore, I. orientalis IPE 100 is a potential candidate for commercial lignocelluloses-to-ethanol production.     

Alkyl-methylimidazolium ionic liquids affect the growth and fermentative metabolism of Clostridium sp

In this study, the effect of ionic liquids, 1-ethyl-3-methylimidazolium acetate [EMIM][Ac], 1-ethyl-3-methylimidazolium diethylphosphate [EMIM][DEP], and 1-methyl-3-methylimidazolium dimethylphosphate [MMIM][DMP] on the growth and glucose fermentation of Clostridium sp. was investigated. Among the three ionic liquids tested, [MMIM][DMP] was found to be least toxic. Growth of Clostridium sp. was not inhibited up to 2.5, 4 and 4 g L⁻¹ of [EMIM][Ac], [EMIM][DEP] and [MMIM][DMP], respectively. [EMIM][Ac] at <2.5 g L⁻¹, showed hormetic effect and stimulated the growth and fermentation by modulating medium pH. Total organic acid production increased in the presence of 2.5 and 2 g L⁻¹ of [EMIM][Ac] and [MMIM][DMP]. Ionic liquids had no significant influence on alcohol production at <2.5 g L⁻¹. Total gas production was affected by ILs at ?2.5 g L⁻¹ and varied with type of methylimidazolium IL. Overall, the results show that the growth and fermentative metabolism of Clostridium sp. is not impacted by ILs at concentrations below 2.5 g L⁻¹.     

Development of an industrial ethanol-producing yeast strain for efficient utilization of cellobiose

The BGL1 gene, encoding β-glucosidase in Saccharomycopsis fibuligera, was intracellular, secreted or cell-wall associated expressed in an industrial strain of Saccharomyces cerevisiae. The obtained recombinant strains were studied under aerobic and anaerobic conditions. The results indicated that both the wild type and recombinant strain expressing intracellular β-glucosidase cannot grow in medium using cellobiose as sole carbon source. As for the recombinant EB1 expressing secreted enzyme and WB1 expressing cell-wall associated enzyme, the maximum specific growth rates (μ_max) could reach 0.03 and 0.05 h⁻¹ under anaerobic conditions, respectively. Meanwhile, the surface-engineered S. cerevisiae utilized 5.2 g cellobiose L⁻¹ and produced 2.3 g ethanol L⁻¹ in 48 h, while S. cerevisiae secreting β-glucosidase into culture broth used 3.6 g cellobiose L⁻¹ and produced 1.5 g ethanol L⁻¹ over the same period, but no-full depletion of cellobiose were observed for both the used recombinant strains. The results suggest that S. cerevisiae used in industrial ethanol production is deficient in cellobiose transporter. However, when β-glucoside permease and β-glucosidase were co-expressed in this strain, it could uptake cellobiose and showed higher growth rate (0.11 h⁻¹) on cellobiose.     

In silico optimization and low structured kinetic model of poly[(R)-3-hydroxybutyrate] synthesis by Cupriavidus necator DSM 545 by fed-batch cultivation on glycerol

Glycerol was utilized by Cupriavidus necator DSM 545 for production of poly-3-hydroxybutyrate (PHB) in fed-batch fermentation. Maximal specific growth rates (0.12 and 0.3 h⁻¹) and maximal specific non-growth PHB production rate (0.16 g g⁻¹ h⁻¹) were determined from two experiments (inocula from exponential and stationary phase). Saturation constants for nitrogen (0.107 and 0.016 g L⁻¹), glycerol (0.05 g L⁻¹), non-growth related PHB synthesis (0.011 g L⁻¹) and nitrogen/PHB related inhibition constant (0.405 g L⁻¹), were estimated. Five relations for specific growth rate were tested using mathematical models. In silico performed optimization procedures (varied glycerol/nitrogen ratio and feeding) has resulted in a PHB content of 70.9%, shorter cultivation time (23 h) and better PHB yield (0.347 g g⁻¹). Initial concentration of biomass 16.8 g L⁻¹ and glycerol concentration in broth between 3 and 5 g L⁻¹ were decisive factors for increasing of productivity.     

Primary production,respiration and calcification of the temperate free-living coralline alga Lithothamnion corallioides

Calcification and primary production responses to irradiance in the temperate coralline alga Lithothamnion corallioides were measured in summer 2004 and winter 2005 in the Bay of Brest. Coralline algae were incubated in dark and clear bottles exposed to different irradiances. Net primary production reached 1.5 μmol C g⁻¹ dry wt h⁻¹ in August and was twice as high as in January–February. Dark respiration showed significant seasonal variations, being three-fold higher in summer. Maximum calcification varied from 0.6 μmol g⁻¹ dry wt h⁻¹ in summer 2004 to 0.4 μmol g⁻¹ dry wt h⁻¹ in winter 2005. According to P–E curves and the daily course of irradiance, estimated daily net production and calcification reached 131 μg C g⁻¹ dry wt and 970 μg CaCO₃ g⁻¹ dry wt in summer 2004, and 36 μg C g⁻¹ dry wt and 336 μg CaCO₃ g⁻¹ dry wt in winter 2005. The net primary production of natural L. corallioides populations in shallow waters was estimated at 10–600 g C m⁻² y⁻¹, depending on depth and algal biomass. The mean annual calcification of L. corallioides populations varied from 300 to 3000 g CaCO₃ m⁻². These results are similar to those reported for tropical coralline algae in terms of carbon and carbonate productivity. Therefore, L. corallioides can be considered as a key element of carbon and carbonate cycles in the shallow coastal waters where they live.     

Evaluation of bioenergy recovery processes treating organic residues from ethanol fermentation process

This study evaluates a two-stage bioprocess for recovering bioenergy in the forms of hydrogen and methane while treating organic residues of ethanol fermentation from tapioca starch. A maximum hydrogen production rate of 0.77 mmol H₂/g VSS/h can be achieved at volumetric loading rate (VLR) of 56 kg COD/m³/day. Batch results indicate that controlling conditions at S₀/X₀ = 12 with X₀ = 4000 mg VSS/L and pH 5.5-6 are important for efficient hydrogen production from fermentation residues. Hydrogen-producing bacteria enriched in the hydrogen bioreactor are likely utilizing lactate and acetate for biohydrogen production from ethanol-fermentation residues. Organic residues remained in the effluent of hydrogen bioreactor can be effectively converted to methane with a rate of 0.37 mmol CH₄/g VSS/h at VLR of 8 kg COD/m³/day. Approximately 90% of COD in ethanol-fermentation residues can be removed and among that 2% and 85.1% of COD can be recovered in the forms of hydrogen and methane, respectively.