Anaerobic hydrogen production with an efficient carrier-induced granular sludge bed bioreactor

A novel bioreactor containing self-flocculated anaerobic granular sludge was developed for high-performance hydrogen production from sucrose-based synthetic wastewater. The reactor achieved an optimal volumetric hydrogen production rate of approximately 7.3 L/h/L (7,150 mmol/d/L) and a maximal hydrogen yield of 3.03 mol H2/mol sucrose when it was operated at a hydraulic retention time (HRT) of 0.5 h with an influent sucrose concentration of 20 g COD/L. The gas-phase hydrogen content and substrate conversion also exceeded 40 and 90%, respectively, under optimal conditions. Packing of a small quantity of carrier matrices on the bottom of the upflow reactor significantly stimulated sludge granulation that can be accomplished within 100 h. Among the four carriers examined, spherical activated carbon was the most effective inducer for granular sludge formation. The carrier-induced granular sludge bed (CIGSB) bioreactor was started up with a low HRT of 4-8 h (corresponding to an organic loading rate of 2.5-5 g COD/h/L) and enabled stable operations at an extremely low HRT (up to 0.5 h) without washout of biomass. The granular sludge was rapidly formed in CIGSB supported with activated carbon and reached a maximal concentration of 26 g/L at HRT = 0.5 h. The ability to maintain high biomass concentration at low HRT (i.e., high organic loading rate) highlights the key factor for the remarkable hydrogen production efficiency of the CIGSB processes.     

Metabolic pathways of hydrogen production in fermentative acidogenic microflora

Biohydrogen production from organic wastewater by anaerobically activated sludge fermentation has already been extensively investigated, and it is known that hydrogen can be produced by glucose fermentation through three metabolic pathways, including the oxidative decarboxylation of pyruvic acid to acetyl-CoA, oxidation of NADH to NAD+, and acetogenesis by hydrogen-producing acetogens. However, the exact or dominant pathways of hydrogen production in the anaerobically activated sludge fermentation process have not yet been identified. Thus, a continuous stirred-tank reactor (CSTR) was introduced and a specifically acclimated acidogenic fermentative microflora obtained under certain operation conditions. The hydrogen production activity and potential hydrogen-producing pathways in the acidogenic fermentative microflora were then investigated using batch cultures in Erlenmeyer flasks with a working volume of 500 ml. Based on an initial glucose concentration of 10 g/l, pH 6.0, and a biomass of 1.01 g/l of a mixed liquid volatile suspended solid (MLVSS), 247.7 ml of hydrogen was obtained after a 68 h cultivation period at 35 +/- 1 degrees C. Further tests indicated that 69% of the hydrogen was produced from the oxidative decarboxylation of pyruvic acid, whereas the remaining 31% was from the oxidation of NADH to NAD+. There were no hydrogen-producing acetogens or they were unable to work effectively in the anaerobically activated sludge with a hydraulic retention time (HRT) of less than 8 h.     

Anaerobic Hydrogen Production from Sucrose Using an Acid‐Enriched Sewage Sludge Microflora

A novel and high‐rate anaerobic sequencing bath reactor (ASBR) process was used to evaluate the hydrogen productivity of an acid‐enriched sewage sludge microflora at a temperature of 35 °C. In this ASBR process a 4 h cycle, including feed, reaction, settle, and decant steps, was repeatedly performed in a 5 L reactor. The sucrose substrate concentration was 20 g COD/L; the hydraulic retention time (HRT) was maintained at 12–120 h at the initial period and thereafter at 4–12 h. The reaction/settle period ratio, which is the most important parameter for ASBR operation was 1.7. The experimental results indicated that the hydrogenic activity of the sludge microflora was HRT‐dependent and that proper pH control was necessary for a stable operation of the bioreactor. The peak hydrogenic activity value was attained at an HRT of 8 h and an organic loading rate of 80 kg COD/m³ × day. Each mole of sucrose in the reactor produced 2.8 mol of hydrogen and each gram of biomass produced 39 mmol of hydrogen per day. An overly‐short HRT might deteriorate the hydrogen productivity. The concentration ratios of butyric acid to’acetic acid, as well as volatile fatty acid and soluble microbial products to alkalinity can be used as monitoring indicators for the hydrogenic bioreactor.     

Modeling and optimization of anaerobic digested sludge converting starch to hydrogen

The pH and hydraulic retention time (HRT) of a chemostat reactor were varied according to a central composite design methodology with the aim of modeling and optimizing the conversion of starch into hydrogen by microorganisms in an anaerobic digested sludge. Experimental results from 23 runs indicate that a maximum hydrogen production rate of 1600 L/m(3)/d under the organic loading rate of 6 kg starch m(3)/d obtained at pH = 5.2 and HRT = 17 h. Throughout this study, the hydrogen percentage in the biogas was approximately 60% and no methanogenesis was observed. while the reactor was operated with HRT of 17 h, hydrogen was produced within a pH range between 4.7 and 5.7. Alcohol production rate was greater than hydrogen production rate if the pH was lower than 4.3 or higher than 6.1. Supplementary experiments confirm that the optimum conditions evaluated in this study were highly reliable; while a hydrogen production yield of 1.29 l H(2)/g starch-COD was obtained. An examination of the response surfaces, including hydrogen, volatile fatty acids (VFA) and alcohols production, led us to the belief that clostridium sp. predominated in the anaerobic hydrogen-producing microorganisms in this study. Experiment results obtained emphasize that the response of metabolites was a more useful indicator than hydrogenic activity for obtaining efficient hydrogen production. Furthermore, expressions of contour plots indicate that Response-Surface Methodology may provide easily interpretable advice on the operation of a hydrogen-producing bioprocess.     

Characterization of a hydrogen-producing granular sludge

This study demonstrated that hydrogen-producing acidogenic sludge could agglutinate into granules in a well-mixed reactor treating a synthetic sucrose-containing wastewater at 26 degrees C, pH 5.5, with 6 h of hydraulic retention. A typical matured granule is 1.6 mm in diameter, 1.038 g/mL in density, 11% in ash content, and over 50 m/h in settling velocity. Treating a solution containing 12.15 g/L of sucrose at a volumetric loading rate of 48.6 g/(L x d), the reactor containing 20 g/L of granular sludge degraded 97% of sucrose. Effluent comprised 46% acetate and 49% butyrate and the methane-free biogas comprised 63% hydrogen, 35% carbon dioxide, and 2% nitrogen. Hydrogen production rate was 13.0 L/(L x d), and the yield was 0.28 L/g-sucrose. The granule had multiple cracks on the surface and comprised two morphological types of bacteria: fusiform bacilli and a spore-forming bacterium. Phylogenetic analysis showed that 69.1% of the clones were affiliated with four Clostridium species in the family Clostridiaceae, and 13.5% with Sporolactobacillus racemicus in the Bacillus/Staphylococcus group.     

Changes in bacterial community during fermentative hydrogen and acid production from organic waste by thermophilic anaerobic microflora

AIMS: Changes in fermentation pattern during the treatment of organic wastes containing solid materials by thermophilic anaerobic microflora were investigated with respect to product formation and bacterial community structure during hydrogen production. METHODS AND RESULTS: Anaerobic microflora enriched from sludge compost was cultivated using artificial garbage slurry in a continuous flow-stirred tank reactor. Product formation varied depending on pH and hydraulic retention time (HRT) applied. Community analysis by terminal restriction fragment length polymorphism and clone library analysis of polymerase chain reaction-amplified bacterial 16S rDNA indicated that difference in the fermentative product distribution could be caused by different populations of micro-organisms in the microflora. CONCLUSION: Hydrogen fermentation with acetate/butyrate formation was optimized at <1.0 d HRT at pH 5.0 and 6.0. Thermoanaerobacterium thermosaccharolyticum was the dominant hydrogen-producing micro-organism. Conversely, unidentified organisms became dominant after 4.0 d HRT at pH 7.0 and 8.0, where relatively high-solubilization efficiency of solid materials was observed with no production of hydrogen. SIGNIFICANCE AND IMPACT OF THE STUDY: This is the first report describing product formation in the fermentation of solid organic wastes by a mixed population of micro-organisms. Various fermentation patterns including hydrogen fermentation were characterized and evaluated from engineering and microbial aspects.     

Quantitative analysis of a high-rate hydrogen-producing microbial community in anaerobic agitated granular sludge bed bioreactors using glucose as substrate

Fermentative H₂ production microbial structure in an agitated granular sludge bed bioreactor was analyzed using fluorescence in situ hybridization (FISH) and polymerase chain reaction-denatured gradient gel electrophoresis (PCR-DGGE). This hydrogen-producing system was operated at four different hydraulic retention times (HRTs) of 4, 2, 1, and 0.5 h and with an influent glucose concentration of 20 g chemical oxygen demand/l. According to the PCR-DGGE analysis, bacterial community structures were mainly composed of Clostridium sp. (possibly Clostridium pasteurianum), Klebsiella oxytoca, and Streptococcus sp. Significant increase of Clostridium/total cell ratio (68%) was observed when the reactor was operated under higher influent flow rate. The existence of Streptococcus sp. in the reactor became more important when operated under a short HRT as indicated by the ratio of Streptococcus probe-positive cells to Clostridium probe-positive cells changing from 21% (HRT 4 h) to 38% (HRT 0.5 h). FISH images suggested that Streptococcus cells probably acted as seeds for self-flocculated granule formation. Furthermore, combining the inspections with hydrogen production under different HRTs and their corresponding FISH analysis indicated that K. oxytoca did not directly contribute to H₂ production but possibly played a role in consuming O₂ to create an anaerobic environment for the hydrogen-producing Clostridium.     

Evaluation of methods for preparing hydrogen-producing seed inocula under thermophilic condition by process performance and microbial community analysis

Five methods for preparation of hydrogen-producing seeds (base, acid, 2-bromoethanesulfonic acid (BESA), load-shock and heat shock treatments) as well as an untreated anaerobic digested sludge were compared for their hydrogen production performance and responsible microbial community structures under thermophilic condition (60 degrees C). The results showed that the load-shock treatment method was the best for enriching thermophilic hydrogen-producing seeds from mixed anaerobic cultures as it completely repressed methanogenic activity and gave the a maximum hydrogen production yield of 1.96 mol H(2) mol(-1) hexose with an hydrogen production rate of 11.2 mmol H(2) l(-1)h(-1). Load-shock and heat-shock treatments resulted in a dominance of Thermoanaerobacterium thermosaccharolyticum with acetic acid and butyric acid type of fermentation while base- and acid-treated seeds were dominated by Clostridium sp. and BESA-treated seeds were dominated by Bacillus sp. The comparative experimental results from hydrogen production performance and microbial community analysis showed that the load-shock treatment method was better than the other four methods for enriching thermophilic hydrogen-producing seeds from anaerobic digested sludge. Load-shock treated sludge was implemented in palm oil mill effluent (POME) fermentation and was found to give maximum hydrogen production rates of 13.34 mmol H(2) l(-1)h(-1) and resulted in a dominance of Thermoanaerobacterium spp. Load-shock treatment is an easy and practical method for enriching thermophilic hydrogen-producing bacteria from anaerobic digested sludge.     

Effects of initial lactic acid concentration, HRTs, and OLRs on bio-hydrogen production from lactate-type fermentation

A batch test and continuous operation were performed to identify the effect of lactate on hydrogen production at pH 4.5. When the initial lactic acid concentration was increased from 0 to 8 g/L in the batch test, the hydrogen yield also increased from 1.41 to 1.72 mol-H₂/mol-glucose. The system exhibited a long lag time and an insignificant hydrogen yield with 16 g-lactic acid/L. A continuous stirred tank reactor (CSTR) was operated at different organic loading rates (OLRs: 10, 15, 20 and 40 g/L/day) and hydraulic retention times (HRTs: 6, 12 and 24 h). At an OLR of 20 g-glucose/L/day and 12 h of HRT, the hydrogen yield was 1.2 mol-H₂/mol-glucose. The yield decreased with a 24 h HRT. Even though lactate was one of the major constituents of volatile fatty acids (VFAs), hydrogen production was feasible throughout the operation. Clostridium sp. was the dominant hydrogen-producing bacteria in the system.     

Production of bio-hydrogen by mesophilic anaerobic fermentation in an acid-phase sequencing batch reactor

The pH and hydraulic retention time (HRT) of an anaerobic sequencing batch reactor (ASBR) were varied to optimize the conversion of carbohydrate-rich synthetic wastewater into bio-hydrogen. A full factorial design using evolutionary operation (EVOP) was used to determine the effect of the factors and to find the optimum condition of each factor required for high hydrogen production rate. Experimental results from 20 runs indicate that a maximum hydrogen production rate of 4,460-5,540 mL/L/day under the volumetric organic loading rate (VOLR) of 75 g-COD/L/day obtained at an observed design point of HRT = 8 h and pH = 5.7. The hydrogen production rate was strongly dependent on the HRT, and the effect was statistically significant (P < 0.05). However, no significant effect (P > 0.05) was found for the pH on the hydrogen production rate. When the ASBR conditions were set for a maximum hydrogen production rate, the hydrogen production yield and specific hydrogen production rate were 60-74 mL/g-COD and 330-360 mL/g-VSS/day, respectively. The hydrogen composition was 43-51%, and no methanogenesis was observed. Acetate, propionate, butyrate, valerate, caproate, and ethanol were major liquid intermediate metabolites during runs of this ASBR. The dominant fermentative types were butyrate-acetate or ethanol-acetate, representing the typical anaerobic pathway of Clostridium species. This hydrogen-producing ASBR had a higher hydrogen production rate, compared with that produced using continuous-flow stirred tank reactors (CSTRs). This study suggests that the hydrogen-producing ASBR is a promising bio-system for prolonged and stable hydrogen production.     

Glyphosate degradation by immobilized bacteria: laboratory studies showing feasibility for glyphosate removal from waste water.

To evaluate immobilized bacteria technology for the removal of low levels of glyphosate (N-phosphonomethylglycine) from aqueous industrial effluents, microorganisms with glyphosate-degrading activity obtained from a fill and draw enrichment reactor inoculated with activated sludge were first exposed to glyphosate production wastes containing 500-2000 mg glyphosate/L. The microorganisms were then immobilized by adsorption onto a diatomaceous earth biocarrier contained in upflow Plexiglas columns. The columns were aerated, maintained at pH 7.0-8.0, incubated at 25 degrees C, supplemented with NH4NO3 (50 mg/L), and exposed to glyphosate process wastes pumped upflow through the biocarrier. Glyphosate degradation to aminomethylphosphonic acid was initially > 96% for 21 days of operation at flows yielding hydraulic residence times (HRTs) as short as 42 min. Higher flow rate studies showed > 98% removal of 50 mg glyphosate/L from the waste stream could be achieved at a HRT of 23 min. Glyphosate removal of > 99% at a 37-min HRT was achieved under similar conditions with a column inoculated with a pure culture of Pseudomonas sp. strain LBr, a bacterium known to have high glyphosate-degrading activity. After acid shocking (pH 2.8 for 18 h) of a column of immobilized bacteria, glyphosate-degrading activity was regained within 4 days without reinoculation. Although microbial growth and glyphosate degradation were not maintained under low organic nutrient conditions in the laboratory, the low levels of degradable carbon (45-94 mg/L) in the industrial effluent were sufficient to support prolonged glyphosate-degrading activity. The results demonstrated that immobilized bacteria technology is effective in removing low levels of glyphosate in high-volume liquid waste streams.     

Two-stage biogas production by co-digesting molasses wastewater and sewage sludge

We evaluated the feasibility of co-digesting molasses wastewater and sewage sludge in a two-stage hydrogen- and methane-producing system. The highest energy was recovered at the 21-h hydraulic retention time (HRT) of the first hydrogenic reactor and at 56-h HRT of the secondary methanogenic reactor. Hence, the two-stage system recovered 1,822 kJ from 1 L of the mixed wastes (19.7: hydrogenic reactor plus, 1,802 kJ L^?1: methanogenic reactor). Despite the overloaded VFA-run with a short HRT of 56 h, the GAC-CH₄ reactor increased methane production rate and yields due to enhanced pH buffer capacity. An RNA-based community analysis showed that the Ethanoligenens and Methanosaeta dominated the hydrogen and methane bioreactor, respectively. The two-stage system of co-digesting molasses and sewage sludge is particularly cost-effective due to non-pretreatment of sewage sludge.     

Fermentative hydrogen production and bacterial community structure in high-rate anaerobic bioreactors containing silicone-immobilized and self-flocculated sludge

A novel continuously stirred anaerobic bioreactor (CSABR) seeded with silicone-immobilized sludge was developed for high-rate fermentative H2 production using sucrose as the limiting substrate. The CSABR system was operated at a hydraulic retention time (HRT) of 0.5-6 h and an influent sucrose concentration of 10-40 g COD/L. With a high feeding sucrose concentration (i.e., 30-40 g COD/L) and a short HRT (0.5 h), the CSABR reactor produced H2 more efficiently with the highest volumetric rate (VH2) of 15 L/h/L (i.e., 14.7 mol/d/L) and an optimal yield of ca. 3.5 mol H2/mol sucrose. The maximum VH2 value obtained from this work is much higher than any other VH2 values ever documented. Formation of self-flocculated granular sludge occurred during operation at a short HRT. The granule formation is thought to play a pivotal role in the dramatic enhancement of H2 production rate, because it led to more efficient biomass retention. A high biomass concentration of up to 35.4 g VSS/L was achieved even though the reactor was operated at an extremely low HRT (i.e., 0.5 h). In addition to gaining high biomass concentrations, formation of granular sludge also triggered a transition in bacterial community structure, resulting in a nearly twofold increase in the specific H2 production rate. According to denatured-gradient-gel-electrophoresis analysis, operations at a progressively decreasing HRT resulted in a decrease in bacterial population diversity. The culture with the best H2 production performance (at HRT = 0.5 h and sucrose concentration = 30 g COD/L) was eventually dominated by a presumably excellent H2-producing bacterial species identified as Clostridium pasteurianum.     

Specific aerobic granules can be developed in a completely mixed tank reactor by bioaugmentation using micro-mycelial pellets of Phanerochaete chrysosporium

Aerobic granules were firstly developed in a completely mixed tank reactor (CMTR) by seeding micro-mycelial pellets (MMPs) of Phanerochaete chrysosporium. During phenol wastewater treatment, sludge granulation rate reached 67 % after 15-day operation. The granules in CMTR are different from aerobic granules described in literature in morphology, and a majority of them are rod-shaped or rodlike sludge besides spherical granules. The polymorphic granules, having no essential difference with aerobic granules previously reported, achieve advantages over conventional activated sludge in settling ability, biomass concentration, density, integrity coefficient and removal ability to phenol wastewater. The optimized parameters for sludge granulation in CMTR including temperature, inoculum quantity, rotary speed and superficial air upflow velocity are 30 °C, 5–7 g/l, 150 rpm, and 0.5 cm/s, respectively. Analysis on sludge granulation mechanism indicates that MMPs not only result in the formation of aerobic granules containing MMPs as nuclei, but also induce the formation of biogranules which do not have MMP at their cores. The work challenges the general belief that the homogenous circular flow pattern of microbial aggregates is necessary for aerobic sludge granulation.     

Effects of key operational parameters on biohydrogen production via anaerobic fermentation in a sequencing batch reactor

In this study, a series of tests were conducted in a 6 L anaerobic sequencing batch reactor (ASBR) to investigate the effect of pH, hydraulic retention time (HRT) and organic loading rate on biohydrogen production at 28 °C. Sucrose was used as the main substrate to mimic carbohydrate-rich wastewater and inoculum was prepared from anaerobic digested sludge without pretreatment. The reactor was operated initially with nitrogen sparging to form anaerobic condition. Results showed that methanogens were effectively suppressed. The optimum pH value would vary depending on the HRT. Maximum hydrogen production rate and yield of 3.04 L H₂/L reactor d and 2.16 mol H₂/mol hexose respectively were achieved at pH 4.5, HRT 30 h, and OLR 11.0 kg/m³ d. Two relationships involving the propionic acid/acetic acid ratio and ethanol/acetic acid ratio were derived from the analysis of the metabolites of fermentation. Ethanol/acetic acid ratio of 1.25 was found to be a threshold value for higher hydrogen production.     

The effect of hydraulic retention time on the stability of aerobically grown microbial granules

AIMS: The aim of this study is to evaluate the effect of hydraulic retention time (HRT) on the development of aerobically grown microbial granules. METHODS AND RESULTS: Five column-shaped sequential aerobic sludge blanket reactors (SASBRs) were seeded with aerobically grown microbial granules and operated in a cyclic mode at different HRTs. At the shortest HRT of 1 h, the strong hydraulic pressure triggered biomass washout and led to reactor failure. At the longest HRT of 24 h, which represented the weakest hydraulic selection in this study, aerobic granules were gradually substituted by bioflocs because of the lower frequency of volumetric exchange. Within the optimum range of HRTs from 2 to 12 h, however, aerobic granules became stabilized in the presence of adequate hydraulic selection in the reactors, with good mixed liquor volatile suspended solids (MLVSS) retention, high volumetric chemical oxygen demand (COD) removal, low sludge volume index (SVI) values, good effluent quality, low sludge production rate, stronger and more compact structures, high cell hydrophobicity and high ratios of extracellular polysaccharides (PS) to extracellular proteins (PN). CONCLUSIONS: HRTs between 2 and 12 h provided the hydraulic selection pressures favourable for the formation and maintenance of stable aerobic granules with good settleability and activity. SIGNIFICANCE AND IMPACT OF THE STUDY: This is the first systematic study on the effect of HRT on heterotrophic aerobic granules. The results of the investigation are useful in understanding how aerobic granules can be applied for wastewater treatment.     

以纸为碳源去除地下水硝酸盐的研究

研究了以纸为碳源和反应介质的生物反应器对水中硝酸盐的去除。结果表明,以纸为碳源的反应器启动快．反硝化反应受温度及水力停留时间影响大。25℃的反硝化速率是14℃的1．7倍。在室温25±1℃,进水硝酸盐氮浓度为45．2mg·L^-1、水力停留时间8．6h时,反应器对硝酸盐氮的去除率在99．6％以上,当水力停留时间为7．2h,氮去除率只有50％。反硝化反应受pH值和溶解氧的影响小,反应进行过程中,纸表面形成了生物膜,纸也被消耗了．采用反应器出水再经活性炭吸附的工艺流程处理高硝酸盐氮地下水,<33．9mg·L^-1的硝酸盐氮完全去除,没有出现NC2-N,最终出水水质DOC<11mg·L^-1。     

Starter culture of <Emphasis Type="Italic">Pseudomonas veronii</Emphasis> strain B for aerobic granulation

Aggregation of bacterial cells is used in formation of microbial granules. Aerobically grown microbial granules can be used as the bio-agents in the treatment of wastewater. However, there are problems with start up of microbial granulation and biosafety of this process. Aim of this research was selection and testing of safe microbial strain with high cell aggregation ability to shorten period of microbial granules formation. Five bacterial strains with cell aggregation index higher than 50% have been isolated from the granules. Strain of Pseudomonas veronii species was considered as most probably safe starter culture for granulation because other strains belonged to the species known as human pathogens. The microbial granules were formed after 3 days of cultivation in case when P. veronii strain B was applied to start-up aerobic granulation process using model wastewater. The granules were produced from activated sludge after 9 days of cultivation. Microbial aggregates produced from starter culture of P. veronii strain B were more compact (sludge volume index was 70 ml/g) than those produced from activated sludge (sludge volume index was 106 ml/g). It is a first proof that application of selected safe starter pure culture with high cell aggregation ability can accelerate and enhance formation of microbial granules.     

Microscopic observation of aerobic granulation in sequential aerobic sludge blanket reactor

AIMS: This paper attempts to provide visual evidence of how aerobic granulation evolves in sequential aerobic sludge blanket reactors. METHODS AND RESULTS: A series of experiments were conducted in two column-type sequential aerobic sludge reactors fed with glucose and acetate as sole carbon source, respectively. The evolution of aerobic granulation was monitored using image analysis and optical and scanning electron microscopy. The results indicated that the formation of aerobic granules was a gradual process from seed sludge to compact aggregates, further to granular sludge and finally to mature granules with the sequential operation proceeding. Glucose- and acetate-fed granules have comparable characteristics in terms of settling velocity, size, shape, biomass density and microbial activity. However, the microbial diversity of the granules was associated with the carbon source supplied. In this work, an important aerobic starvation phase was identified during sequential operation cycles. It was found that periodical aerobic starvation was an effective trigger for microbial aggregation in the reactor and further strengthened cell-cell interaction to form dense aggregates, which was an essential step of granulation. The periodical starvation-induced aggregates would finally be shaped to granules by hydrodynamic shear and flow. CONCLUSION: Aerobic granules can be formed within 3 weeks in the systems. The periodical starvation and hydrodynamic conditions would play a crucial role in the granulation process. SIGNIFICANCE AND IMPACT OF THE STUDY: Aerobic granules have excellent physical characteristics as compared with conventional activated sludge flocs. This research could be helpful for the development of an aerobic granule-based novel type of reactor for handling high strength organic wastewater.     

Comparative analysis of hydrogen-producing bacterial biofilms and granular sludge formed in continuous cultures of fermentative bacteria

A system for biohydrogen production was developed based on long-term continuous cultures grown on sugar beet molasses in packed bed reactors. In two separate cultures, consortia of fermentative bacteria developed as biofilms on granitic stones. In one of the cultures, a granular sludge was also formed. Metagenomic analysis of the microbial communities by 454-pyrosequencing of amplified 16S rDNA fragments revealed that the overall biodiversity of the hydrogen-producing cultures was quite small. The stone biofilm from the culture without granular sludge was dominated by Clostridiaceae and heterolactic fermentation bacteria, mainly Leuconostocaeae. Representatives of the Leuconostocaeae and Enterobacteriaceae were dominant in both the granules and the stone biofilm formed in the granular sludge culture. The culture containing granular sludge produced hydrogen significantly more effectively than that containing only the stone biofilm: 5.43 vs. 2.8 mol H₂/mol sucrose from molasses, respectively. The speculations that lactic acid bacteria may favor hydrogen production are discussed.