The effects of different articulate curvature of artificial disc on loading distribution

Purpose: Deeper insights into the mechanical behavior of lumbar disc prostheses are required. Prior studies on the biomechanical performance of artificial discs were mostly performed with finite element analyses, but this has never been analyzed with altering articulate curvature. This study aimed to ascertain the influence of the geometry of a ball-and-socket disc prosthesis for the lumbar spine. Materials and Methods: Three-dimensional finite element model of human L4-L5 was reconstructed. Convex, concave, and elliptic artificial disc models were also established with Computer-Aided-Design software. Simulations included: (1) three articulate types of polyethylene (PE) insert were implanted inferiorly and (2) concave and convex PE inserts were implanted on the superior or inferior sides in flexion/extension, lateral bending, and axial rotation in the lumbar spine. Shear stresses and von Mises stresses on PE insert were assessed for their loading distributions. Results: High shear stresses of all articulate types occurred in flexion, and convex PE insert performed the maximum stress of 23.81 MPa. Under all conditions, stresses on concave PE inserts were distributed more evenly and lower than those on the convex type. Elliptic geometry enabled confining the rotation of the motion unit. The shear force on the convex PE insert on the inferior side could induce transverse crack because the shear stress exceeded yielding shear stress. Conclusions: The concave PE insert on the inferior side not only decreased loading concentration but had relatively low stress. Such a design may be applicable for artificial discs.     

The influence of different magnitudes and methods of applying preload on fusion and disc replacement constructs in the lumbar spine: a finite element analysis

In a finite element (FE) analysis of the lumbar spine, different preload application methods that are used in biomechanical studies may yield diverging results. To investigate how the biomechanical behaviour of a spinal implant is affected by the method of applying the preload, hybrid-controlled FE analysis was used to evaluate the biomechanical behaviour of the lumbar spine under different preload application methods. The FE models of anterior lumbar interbody fusion (ALIF) and artificial disc replacement (ADR) were tested under three different loading conditions: a 150 N pressure preload (PP) and 150 and 400 N follower loads (FLs). This study analysed the resulting range of motion (ROM), facet contact force (FCF), inlay contact pressure (ICP) and stress distribution of adjacent discs. The FE results indicated that the ROM of both surgical constructs was related to the preload application method and magnitude; differences in the ROM were within 7% for the ALIF model and 32% for the ADR model. Following the application of the FL and after increasing the FL magnitude, the FCF of the ADR model gradually increased, reaching 45% at the implanted level in torsion. The maximum ICP gradually decreased by 34.1% in torsion and 28.4% in lateral bending. This study concluded that the preload magnitude and application method affect the biomechanical behaviour of the lumbar spine. For the ADR, remarkable alteration was observed while increasing the FL magnitude, particularly in the ROM, FCF and ICP. However, for the ALIF, PP and FL methods had no remarkable alteration in terms of ROM and adjacent disc stress.     

Effects of several temporomandibular disorders on the stress distributions of temporomandibular joint: a finite element analysis

The aim of this study was to evaluate stress distributions in the temporomandibular joints (TMJs) with temporomandibular disorders (TMDs) for comparison with healthy TMJs. A model of mandible and normal TMJs was developed according to CT images. The interfaces between the discs and the articular cartilages were treated as contact elements. Nonlinear cable elements were used to simulate disc attachments. Based on this model, seven models of various TMDs were established. The maximum stresses of the discs with anterior, posterior, medial and lateral disc displacement (ADD, PDD, MDD and LDD) were 12.09, 9.33, 10.71 and 6.07 times magnitude of the identically normal disc, respectively. The maximum stresses of the posterior articular eminences in ADD, PDD, MDD, LDD, relaxation of posterior attachments and disc perforation models were 21, 59, 46, 21, 13 and 15 times greater than the normal model, respectively. TMDs could cause increased stresses in the discs and posterior articular eminences.     

Biomechanics of the C5-C6 Spinal Unit Before and After Placement of a disc prosthesis

The study consists of a biomechanical comparison between the intact C5–C6 spinal segment and the same segment implanted with the Bryan^TM artificial disc prosthesis (Medtronic Ltd., Memphis, TN, USA), by the use of the finite element (FE) method. Our target is the prediction of the influence of prosthesis placement on the resulting mechanics of the C5–C6 spine unit. A FE model of the intact C5–C6 segment was built, employing realistic models of the vertebrae, disc and ligaments. Simulations were conducted imposing a compression preload combined to a flexion/extension moment, a pure lateral bending moment and a pure torsion moment, and the calculated results were compared to data from literature. The model was then modified to include the Bryan^TM cervical disc prosthesis, and the simulations were repeated. The location of the instantaneous center of rotation (ICR) of C5 with respect to C6 throughout flexion/extension was calculated in both models. In general, the moment–rotation curves obtained from the disc prosthesis-implanted model were comparable to the curves obtained from the intact model, except for a slightly greater stiffness induced by the artificial disc. The position of the calculated ICRs was rather stable throughout flexion-extension and was generally confined to a small area, qualitatively matching the corresponding physiological region, in both models. These results imply that the Bryan^TM disc prosthesis allows to correctly reproduce a physiological flexion/extension at the implanted level. The results of this study have quantified aspects that may assist in optimizing cervical disc replacement primarily from a biomechanical point of view.     

Nonlinear finite element analysis of anular lesions in the L4/5 intervertebral disc

Degenerate intervertebral discs exhibit both material and structural changes. Structural defects (lesions) develop in the anulus fibrosus with age. While degeneration has been simulated in numerous previous studies, the effects of structural lesions on disc mechanics are not well known. In this study, a finite element model (FEM) of the L4/5 intervertebral disc was developed in order to study the effects of anular lesions and loss of hydrostatic pressure in the nucleus pulposus on the disc mechanics. Models were developed to simulate both healthy and degenerate discs. Degeneration was simulated with either rim, radial or circumferential anular lesions and by equating nucleus pressure to zero. The anulus fibrosus ground substance was represented as a nonlinear incompressible material using a second-order polynomial, hyperelastic strain energy equation. Hyperelastic material parameters were derived from experimentation on sheep discs. Endplates were assumed to be rigid, and annulus lamellae were assumed to be vertical in the unloaded state. Loading conditions corresponding to physiological ranges of rotational motion were applied to the models and peak rotation moments compared between models. Loss of nucleus pulposus pressure had a much greater effect on the disc mechanics than the presence of anular lesions. This indicated that the development of anular lesions alone (prior to degeneration of the nucleus) has minimal effect on disc mechanics, but that disc stiffness is significantly reduced by the loss of hydrostatic pressure in the nucleus. With the degeneration of the nucleus, the outer innervated anulus or surrounding osteo-ligamentous anatomy may therefore experience increased strains.     

Surface slide track mapping of implants for total disc arthroplasty

Total disc arthroplasty has recently become a potential alternative to spinal arthrodesis. Until recently, there has been no standardized method for evaluating the wear of an artificial disc and myriad testing conditions have been used. The American Society for Testing and Materials (ASTM) and International Organization of Standardization (ISO) recently published guidance documents for the wear assessment of intervertebral spinal disc prostheses; however, various kinematic profiles are suggested, leading to different wear paths between the articulating surfaces of the implants. Since the wear between materials is influenced by the type of relative motion, it is important to select test conditions that lead to clinically realistic results. The purpose of this study was to characterize the slide tracks generated by 7 test conditions allowed for by the ISO and ASTM guidance documents and in Euler sequences consistent with 4 commercially available spine wear simulators. The analysis was performed for a ball-in-socket articulation under both lumbar and cervical motion test conditions. Results were generated analytically using a mathematical algorithm and then validated experimentally. Four tests resulted in elliptical sliding tracks of similar geometries for both the lumbar and cervical conditions. Curvilinear and ribbon-shaped wear paths were generated for 3 tests. With the data normalized for implant diameter, the sliding distance was similar between the lumbar and cervical conditions allowed for in the ASTM guidance. This distance differed compared with the results for the ISO guidance document where the lengths of cervical slide tracks were twice those for the lumbar conditions. Slide tracks were also found to be insensitive to the type of simulator under all testing conditions.     

Morphometric analysis of vertebrae and intervertebral discs as a basis of disc replacement

In this study measurements were obtained from 359 vertebrae and 215 intervertebral discs in an attempt to classify discs by their size. At the cervical and thoracic levels, this attempt was unproductive because of extensive variations. In the lumbar spine, discs were allocated to six size-matched groups and to two height-matched groups. The breadth of marginal rims were also measured with a view to provide surgeons operating on the spine with precise data on disc morphology to facilitate disc replacement.     

腰椎Cage手术并发症分析及其防治

目的:分析后路腰椎椎间cage融合术常见的并发症并探讨对策。方法:对89例腰椎间盘突出症、下腰椎失稳症患者,经临床症状、体征和影像资料明确诊断且具有手术指征,并采用后路cage融合术治疗,对其中出现的并发症进行原因分析。结果:89例中出现并发症的有24例,包括神经症状加重、脑脊液漏、感染等近期并发症和症状缓解不明显、植骨不融合等远期并发症。术后神经症状加重5例,主要与手术适应症选择正确与否、影像学资料阅读能力高低、术者操作技能熟练程度等因素有关。结论:cage融合术是外科治疗椎间盘突出症的一种优良方法,术后神经症状加重和神经根损伤是最常见的并发症,正确把握手术适应症、熟练掌握操作技巧、提高并发症的诊断和处理能力是顺利开展该技术、提高临床疗效的关键。     

High pressures and asymmetrical stresses in the scoliotic disc in the absence of muscle loading

Background

Loads acting on scoliotic spines are thought to be asymmetric and involved in progression of the scoliotic deformity; abnormal loading patterns lead to changes in bone and disc cell activity and hence to vertebral body and disc wedging. At present however there are no direct measurements of intradiscal stresses or pressures in scoliotic spines. The aim of this study was to obtain quantitative measurements of the intradiscal stress environment in scoliotic intervertebral discs and to determine if loads acting across the scoliotic spine are asymmetric. We performed in vivo measurements of stresses across the intervertebral disc in patients with scoliosis, both parallel (termed horizontal) and perpendicular (termed vertical) to the end plate, using a side mounted pressure transducer (stress profilometry)

Methods

Stress profilometry was used to measure horizontal and vertical stresses at 5 mm intervals across 25 intervertebral discs of 7 scoliotic patients during anterior reconstructive surgery. A state of hydrostatic pressure was defined by identical horizontal and vertical stresses for at least two consecutive readings. Results were compared with similar stress profiles measured during surgery across 10 discs of 4 spines with no lateral curvature and with data from the literature.

Results

Profiles across scoliotic discs were very different from those of normal, young, healthy discs of equivalent age previously presented in the literature. Hydrostatic pressure regions were only seen in 14/25 discs, extended only over a short distance. Non-scoliotic discs of equivalent age would be expected to show large centrally placed hydrostatic nuclear regions in all discs. Mean pressures were significantly greater (0.25 MPa) than those measured in other anaesthetised patients (<0.07 MPa). A stress peak was seen in the concave annulus in 13/25 discs. Stresses in the concave annulus were greater than in the convex annulus indicating asymmetric loading in these anaesthetised, recumbent patients.

Conclusion

Intradiscal pressures and stresses in scoliotic discs are abnormal, asymmetrical and high in magnitude even in the absence of significant applied muscle loading. The origin of these abnormal stresses is unclear.     

Immunolocalization of type X collagen in human lumbar intervertebral discs during ageing and degeneration

 Type X collagen has so far not been reported to occur in human intervertebral discs. The objective of this study was therefore to investigate the occurrence of type X collagen in human lumbar intervertebral discs during ageing and degeneration. Ninety intervertebral discs with adjacent endplates were excised in toto from individuals (0–86 years) without known spinal disease and were processed for routine decalcified histology. Appropriate slices of each disc were processed for immunohistochemistry using a type-spec ific, monoclonal antibody raised against human type X collagen. Each intervertebral disc was examined for macroscopic and histomorphological features of disc degeneration. Immunohistochemically, a positive specific type X staining was observed in the hypertrophic zone of the growth plate and only in the interstitial matrix of juvenile (<2 years) nucleus pulposus. In adult discs, type X collagen could be localized in conjunction with advanced disc degeneration and first occurred in the disc matrix (i.e., pericellular region) of a 47-year-old specimen. Positive type X staining of the disc matrix was more frequently found in senile (>70 years) discs with end stages of disc degeneration. This study provides the first evidence for the occurrence of type X collagen in human lumbar intervertebral discs and it appears that type X collagen is re-expressed in late stages of disc degeneration. Accepted: 24 April 1997     

A combined numerical and experimental technique for estimation of the forces and moments in the lumbar intervertebral disc

Evaluation of the loads on lumbar intervertebral discs (IVD) is critically important since it is closely related to spine biomechanics, pathology and prosthesis design. Non-invasive estimation of the loads in the discs remains a challenge. In this study, we proposed a new technique to estimate in vivo loads in the IVD using a subject-specific finite element (FE) model of the disc and the kinematics of the disc endplates as input boundary conditions. The technique was validated by comparing the forces and moments in the discs calculated from the FE analyses to the in vitro experiment measurements of three corresponding lumbar discs. The results showed that the forces and moments could be estimated within an average error of 20%. Therefore, this technique can be a promising tool for non-invasive estimation of the loads in the discs and may be extended to be used on living subjects.     

Damage accumulation location under cyclic loading in the lumbar disc shifts from inner annulus lamellae to peripheral annulus with increasing disc degeneration

It is difficult to study the breakdown of lumbar disc tissue over several years of exposure to bending and lifting by experimental methods. In our earlier published study we have shown how a finite element model of a healthy lumbar motion segment was used to predict the damage accumulation location and number of cyclic to failure under different loading conditions. The aim of the current study was to extend the continuum damage mechanics formulation to the degenerated discs and investigate the initiation and progression of mechanical damage. Healthy disc model was modified to represent degenerative discs (Thompson grade III and IV) by incorporating both geometrical and biochemical changes due to degeneration. Analyses predicted decrease in the number of cycles to failure with increasing severity of disc degeneration. The study showed that the damage initiated at the posterior inner annulus adjacent to the endplates and propagated outwards towards its periphery in healthy and grade III degenerated discs. The damage accumulated preferentially in the posterior region of the annulus. However in grade IV degenerated disc damage initiated at the posterior outer periphery of the annulus and propagated circumferentially. The finite element model predictions were consistent with the infrequent occurrence of rim lesions at early age but a much higher incidence in severely degenerated discs.     

Computational pharmacokinetics of solute penetration into human intervertebral discs-Effects of endplate permeability, solute molecular weight and disc size

A finite element model is developed to predict the penetration time-history of three different solutes into the human lumbar disc following intravenous injection. Antibiotics are routinely administered intravenously in spinal surgery to prevent disc infection. Successful prophylaxis requires antibiotics to reach adequate inhibitory levels. Here, the transient diffusion of cephazolin is investigated over 10h post-injection in a human disc model subject to reported concentrations in the blood stream as the prescribed boundary sources. Post-injection variation of cephazolin concentrations in the disc adjacent to supply sources closely followed the decay curve in the blood stream and fell sharply with time. Much lower concentrations were computed in the inner annulus and nucleus; much of the disc (80% at 1h and 49% at 4h) experienced concentrations below required inhibitory level of 1mg/L in agreement with measurements. Changes in endplate permeability, disc size, and solute molecular weight had profound effects on concentration profiles at all times and regions, especially in the disc centre, demonstrating their crucial roles on the adequate delivery of drugs. Larger solutes markedly slow transport into the disc. The failure to reach critical therapeutic levels in the central disc regions, especially when endplates calcify and in larger discs, raises concerns and calls for caution in attempts to extrapolate findings of studies on animals with much smaller and non degenerate discs to the human discs. The current study also demonstrates the capability of computational models in predicting the transport of intravenously injected solutes into the disc.     

Cervical Total Disc Replacement is Superior to Anterior Cervical Decompression and Fusion: A Meta-Analysis of Prospective Randomized Controlled Trials

Background

Despite being considered the standard surgical procedure for symptomatic cervical disc disease, anterior cervical decompression and fusion invariably accelerates adjacent segment degeneration. Cervical total disc replacement is a motion-preserving procedure developed as a substitute to fusion. Whether cervical total disc replacement is superior to fusion remains unclear.

Methods

We comprehensively searched PubMed, EMBASE, Medline, and the Cochrane Library in accordance with the inclusion criteria to identify possible studies. The retrieved results were last updated on December 12, 2014. We classified the studies as short-term and midterm follow-up.

Results

Nineteen randomized controlled trials involving 4516 cases were identified. Compared with anterior cervical decompression and fusion, cervical total disc replacement had better functional outcomes (neck disability index [NDI], NDI success, neurological success, neck pain scores reported on a numerical rating scale [NRS], visual analog scales scores and overall success), greater segmental motion at the index level, fewer adverse events and fewer secondary surgical procedures at the index and adjacent levels in short-term follow-up (P < 0.05). With midterm follow-up, the cervical total disc replacement group indicated superiority in the NDI, neurological success, pain assessment (NRS), and secondary surgical procedures at the index level (P < 0.05). The Short Form 36 (SF-36) and segmental motion at the adjacent level in the short-term follow-up showed no significant difference between the two procedures, as did the secondary surgical procedure rates at the adjacent level with midterm follow-up (P > 0.05).

Conclusions

Cervical total disc replacement presented favorable functional outcomes, fewer adverse events, and fewer secondary surgical procedures. The efficacy and safety of cervical total disc replacement are superior to those of fusion. Longer-term, multicenter studies are required for a better evaluation of the long-term efficacy and safety of the two procedures.     

Nucleus implant parameters significantly change the compressive stiffness of the human lumbar intervertebral disc

Nucleus replacement by a synthetic material is a recent trend for treatment of lower back pain. Hydrogel nucleus implants were prepared with variations in implant modulus, height, and diameter Human lumbar intervertebral discs (IVDs) were tested in compression for intact, denucleated, and implanted condition. Implantation of nucleus implants with different material and geometric parameters into a denucleated IVD significantly altered the IVD compressive stiffness. Variations in the nucleus implant parameters significantly change the compressive stiffness of the human lumbar IVD. Implant geometrical variations were more effective than those of implant modulus variations in the range examined.     

Dependence of mechanical behavior of the murine tail disc on regional material properties: a parametric finite element study

In vivo rodent tail models are becoming more widely used for exploring the role of mechanical loading on the initiation and progression of intervertebral disc degeneration. Historically, finite element models (FEMs) have been useful for predicting disc mechanics in humans. However, differences in geometry and tissue properties may limit the predictive utility of these models for rodent discs. Clearly, models that are specific for rodent tail discs and accurately simulate the disc's transient mechanical behavior would serve as important tools for clarifying disc mechanics in these animal models. An FEM was developed based on the structure, geometry, and scale of the mouse tail disc. Importantly, two sources of time-dependent mechanical behavior were incorporated: viscoelasticity of the matrix, and fluid permeation. In addition, a novel strain-dependent swelling pressure was implemented through the introduction of a dilatational stress in nuclear elements. The model was then validated against data from quasi-static tension-compression and compressive creep experiments performed previously using mouse tail discs. Finally, sensitivity analyses were performed in which material parameters of each disc subregion were individually varied. During disc compression, matrix consolidation was observed to occur preferentially at the periphery of the nucleus pulposus. Sensitivity analyses revealed that disc mechanics was greatly influenced by changes in nucleus pulposus material properties, but rather insensitive to variations in any of the endplate properties. Moreover, three key features of the model-nuclear swelling pressure, lamellar collagen viscoelasticity, and interstitial fluid permeation-were found to be critical for accurate simulation of disc mechanics. In particular, collagen viscoelasticity dominated the transient behavior of the disc during the initial 2200 s of creep loading, while fluid permeation governed disc deformation thereafter. The FEM developed in this study exhibited excellent agreement with transient creep behavior of intact mouse tail motion segments. Notably, the model was able to produce spatial variations in nucleus pulposus matrix consolidation that are consistent with previous observations in nuclear cell morphology made in mouse discs using confocal microscopy. Results of this study emphasize the need for including nucleus swelling pressure, collagen viscoelasticity, and fluid permeation when simulating transient changes in matrix and fluid stress/strain. Sensitivity analyses suggest that further characterization of nucleus pulposus material properties should be pursued, due to its significance in steady-state and transient disc mechanical response.     

An accurate finite element model of the cervical spine under quasi-static loading

Cervical disc injury due to impact has been observed in clinical and biomechanical investigations; however, there is a lack of data that helps to elucidate the mechanisms of disc injury during these collisions. Therefore, it is necessary to understand the behavior of the cervical spine under different types of loading situations. A three dimensional finite element (FE) model for the multi-level cervical spine segment (C0-C7) was developed using computed tomography (CT) data and applied to study the internal stresses and strains of the intervertebral discs under quasi-static loading conditions. The intervertebral discs were treated as nonlinear, anisotropic and incompressible subjected to large deformations. The model accuracy was validated by comparing it with previously published experimental and numerical results for different movements. It was shown that the use of a fiber reinforced model to describe the behavior of the annulus of the discs would predict higher maximum shear strains than an isotropic one, being therefore important the use of complex constitutive models in order to be able to detect the appearance of injured zones, since those strains and stresses are supposed to be related with damage to soft tissues. Several movements were analyzed: flexion, extension and axial rotation, obtaining that the maximum shear stresses in the disc were higher for a flexo-extension movement.     

Novel model to analyze the effect of a large compressive follower pre-load on range of motions in a lumbar spine

A 3-D finite element model (FEM) of the lumbar spine (L1-S1) was used to determine the effect of a large compressive follower pre-load on range of motions (ROM) in all three planes. The follower load modeled in the FEM produced minimal vertebral rotations in all the three planes. The model was validated by comparing the disc compression at all levels in the lumbar spine with the corresponding results obtained by compressing 10 cadevaric lumbar spines (L1-S1) using the follower load technique described by Patwardhan et al. [1999. A follower load increases the load-carrying capacity of the lumbar spine in compression. Spine 24(10), 1003-1009]. Further validation of the model was performed by comparing the lateral bending and torsion response without pre-load and the flexion-extension response without pre-load and with an 800 N follower pre-load with those obtained using cadaver lumbar spines. Following validation, the FEM was subjected to bending moments in all three planes with and without compressive follower pre-loads of up to 1200 N. Disc compression values and the flexion-extension range of motion under 800 N follower pre-load predicted by the FEM compared well with in vitro results. The current model showed that compressive follower pre-load decreased total as well as segmental ROM in flexion-extension by up to 18%, lateral bending by up to 42%, and torsion by up to 26%.     

Biomechanical implications of lumbar spinal ligament transection

Many lumbar spine surgeries either intentionally or inadvertently damage or transect spinal ligaments. The purpose of this work was to quantify the previously unknown biomechanical consequences of isolated spinal ligament transection on the remaining spinal ligaments (stress transfer), vertebrae (bone remodelling stimulus) and intervertebral discs (disc pressure) of the lumbar spine. A finite element model of the full lumbar spine was developed and validated against experimental data and tested in the primary modes of spinal motion in the intact condition. Once a ligament was removed, stress increased in the remaining spinal ligaments and changes occurred in vertebral strain energy, but disc pressure remained similar. All major biomechanical changes occurred at the same spinal level as the transected ligament, with minor changes at adjacent levels. This work demonstrates that iatrogenic damage to spinal ligaments disturbs the load sharing within the spinal ligament network and may induce significant clinically relevant changes in the spinal motion segment.