A high-throughput matrix-assisted laser desorption/ionization-time-of-flight mass spectrometry-based assay of chitinase activity

A high-throughput matrix-assisted laser desorption/ionization–time-of-flight mass spectrometry (MALDI–TOF MS) assay is described for determination of chitolytic enzyme activity. The assay uses unmodified chitin oligosaccharide substrates and is readily achievable on a microliter scale (2 μl of total volume containing 2 μg of substrate and 1 ng of protein). The speed and sensitivity of the assay make it potentially well suited for the high-throughput screening of chitinase inhibitors. The mass spectrum is acquired in approximately 2 min, as opposed to typically 30–40 min for a single run with a high-performance liquid chromatography (HPLC)-based assay. By using the multiple-place MALDI MS targets, we estimate that 100 assays could be run in approximately 2–3 h without needing to remove the target from the instrument. In addition, because the substrate and product chitomers are visualized simultaneously in the TOF spectrum, this gives immediate information about the cleavage site and mechanism of the enzyme under study. The assay was used to monitor the purification and transgenic expression of plant class IV chitinases. By performing the assay with chitomer substrates and C-glycoside chitomer analogs, the enzyme mechanism of the class IV chitinases is described for the first time.     

Enhancement of ovarian tumor classification by improved reproducibility in matrix-assisted laser desorption/ionization time-of-flight mass spectrometry of serum glycans

The serum N-glycome is a promising source of biomarker discovery. Matrix-assisted laser desorption/ionization time-of-flight (MALDI–TOF) mass spectrometry (MS) profiling of serum N-glycans was attempted for differentiating borderline ovarian tumor from benign cases, for which a low data spread is essential. An experimental protocol using matrix-prespotted MALDI plates and fast vacuum drying of the loaded N-glycan samples was developed, thereby minimizing the intensity variations in the replicates to an average relative standard deviation (RSD) of 3.96% for the highest N-glycan peak (m/z 1485.53) of the Sigma–Aldrich serum standard. When applied to sera of ovarian tumors, this procedure exhibited an average RSD of 5.74% for m/z 1485.53 and of 7.28% for all MS peaks. This improved reproducibility combined with the OVA-Beyond^® screening software resulted in 75.1% and 79.4% correct classification for benign and borderline tumor samples, respectively, while the classification rates by the conventional ovarian tumor marker CA-125 were 54.4% and 53.1%, respectively. Both true positive rate and true negative rate fluctuated with small numbers of markers and converged as the number of markers increased. Cross-validations were performed in comparison with CA-125. These results suggest that our optimized process for MALDI–TOF MS of the serum glycome has a great potential for the screening of early stage ovarian cancer.     

Stationary phase thickness determines the quality of thin-layer chromatography/matrix-assisted laser desorption and ionization mass spectra of lipids

Normal phase thin-layer chromatography (NP TLC) is an established method of (phospho)lipid analysis. The determination of the fatty acyl composition is, however, a more challenging task by NP TLC. The direct coupling of TLC separation with mass spectrometric detection (e.g., matrix-assisted laser desorption/ionization mass spectrometry, MALDI MS), however, enables a detailed characterization of complex lipid mixtures. Here we show that the thickness of the silica gel layer has a considerable effect on the quality of the mass spectra recorded directly from the TLC plate. In particular, the intensity of the matrix background signals can be reduced if “thinner” TLC layers are used.     

Determination of prolidase activity using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

Proline-containing peptides of the X-proline type are cleaved by the dipeptidase prolidase. The classical method of prolidase assay relied on the colorimetric estimation of the liberated proline with ninhydrin using acidic media and heat. This method, however, gave inconsistent results due to the nonspecificity of the ninhydrin color reaction. We report here a method for the detection of the liberated proline using matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry. Human sera were incubated with a mixture containing the dipeptide glycyl-proline in Tris-HCl supplemented with manganese at 37 degrees C for 24h. The samples were precipitated with trifluoroacetic acid and centrifuged. An aliquot of the supernatant was mixed with an equal volume of ferulic acid solution. An aliquot from this mixture was spotted on a stainless steel mass spectrometry grid and analyzed using MALDI-TOF mass spectrometry. The activity of the enzyme was determined by the complete disappearance of the glycyl-proline peak with the concomitant appearance of the proline peak and can be expressed in terms of the ratio of the area beneath the proline to the area beneath the glycyl-proline peak. Subjects homozygous for prolidase deficiency had a ratio ranging from 0.006 to 0.04 while obligatory heterozygotes had a ratio ranging from around 1.1 to 2.4. Normal subjects had ratios ranging from 9 to 239. Using this method we have unambiguously identified subjects with homozygous or heterozygous prolidase deficiency. In addition to the advantage of rapid sample preparation time, this method is highly specific, reproducible, and sensitive.     

The application of atmospheric pressure matrix-assisted laser desorption/ionization to the analysis of long-term cryopreserved serum peptidome

Although most time-of-flight (TOF) mass spectrometers come equipped with vacuum matrix-assisted laser desorption/ionization (MALDI) sources, the atmospheric pressure MALDI (API–MALDI) source is an attractive option because of its ability to be coupled to a wide range of analyzers. This article describes the use of an API–MALDI source coupled to a TOF mass spectrometer for evaluation of the effects of medium- and long-term storage on peptidomic profiles of cryopreserved serum samples from healthy women. Peptides were purified using superparamagnetic beads either from fresh sera or after serum storage at −80 °C for 18 months or at −20 °C for 8 years. Data were preprocessed using newly developed bioinformatic tools and then were subjected to statistical analysis and class prediction. The analyses showed a dramatic effect of storage on the abundance of several peptides such as fibrinopeptides A and B, complement fractions, bradykinin, and clusterin, indicated by other authors as disease biomarkers. Most of these results were confirmed by shadow clustering analysis, able to classify each sample in the correct group. In addition to demonstrating the suitability of the API–MALDI technique for peptidome profiling studies, our data are of relevance for retrospective studies that involve frozen sera stored for many years in biobanks.     

Evaluating factor XIII specificity for glutamine-containing substrates using a matrix-assisted laser desorption/ionization time-of-flight mass spectrometry assay

Activated factor XIII (FXIIIa) catalyzes the formation of γ-glutamyl-ε-lysyl cross-links within the fibrin blood clot network. Although several cross-linking targets have been identified, the characteristic features that define FXIIIa substrate specificity are not well understood. To learn more about how FXIIIa selects its targets, a matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI–TOF MS)-based assay was developed that could directly follow the consumption of a glutamine-containing substrate and the formation of a cross-linked product with glycine ethylester. This FXIIIa kinetic assay is no longer reliant on a secondary coupled reaction, on substrate labeling, or on detecting only the final deacylation portion of the transglutaminase reaction. With the MALDI–TOF MS assay, glutamine-containing peptides derived from α₂-antiplasmin, Staphylococcus aureus fibronectin binding protein A, and thrombin-activatable fibrinolysis inhibitor were examined directly. Results suggest that the FXIIIa active site surface responds to changes in substrate residues following the reactive glutamine. The P₋₁ substrate position is sensitive to charge character, and the P₋₂ and P₋₃ substrate positions are sensitive to the broad FXIIIa substrate specificity pockets. The more distant P₋₈ to P₋₁₁ region serves as a secondary substrate anchoring point. New knowledge on FXIIIa specificity may be used to design better substrates or inhibitors of this transglutaminase.     

Liquid ultraviolet matrix-assisted laser desorption/ionization -- mass spectrometry for automated proteomic analysis

We have combined several key sample preparation steps for the use of a liquid matrix system to provide high analytical sensitivity in automated ultraviolet -- matrix-assisted laser desorption/ionisation -- mass spectrometry (UV-MALDI-MS). This new sample preparation protocol employs a matrix-mixture which is based on the glycerol matrix-mixture described by Sze et al. The low-femtomole sensitivity that is achievable with this new preparation protocol enables proteomic analysis of protein digests comparable to solid-state matrix systems. For automated data acquisition and analysis, the MALDI performance of this liquid matrix surpasses the conventional solid-state MALDI matrices. Besides the inherent general advantages of liquid samples for automated sample preparation and data acquisition the use of the presented liquid matrix significantly reduces the extent of unspecific ion signals in peptide mass fingerprints compared to typically used solid matrices, such as 2,5-dihydroxybenzoic acid (DHB) or alpha-cyano-hydroxycinnamic acid (CHCA). In particular, matrix and low-mass ion signals and ion signals resulting from cation adduct formation are dramatically reduced. Consequently, the confidence level of protein identification by peptide mass mapping of in-solution and in-gel digests is generally higher.     

Rapid estimation of the energy charge from cell lysates using matrix-assisted laser desorption/ionization mass spectrometry: Role of in-source fragmentation

Nucleotides are key players in the central energy metabolism of cells. Here we show how to estimate the energy charge from cell lysates by direct negative ion matrix-assisted laser desorption/ionization mass spectrometry (MALDI–MS) using 9-aminoacridine as matrix. We found a high level of in-source decay of all the phosphorylated nucleotides, with some of them producing considerable amounts of adenosine-5′-diphosphate (ADP) fragment ions. We investigated the behavior of adenosine-5′-monophosphate (AMP), ADP, and adenosine-5′-triphosphate (ATP) as well as the cofactors coenzyme A (CoA) and acetyl-coenzyme A (ACoA) and nicotinamide adenine dinucleotides (NAD⁺ and NADH) in detail. In-source decay of these compounds depends strongly on the applied laser power and on the extraction pulse delay. At standard instrument settings, the 9-aminoacridine (9-AA) matrix resulted in a much higher in-source decay compared with 2,4,6-trihydroxyacetophenone (2,4,6-THAP). By adding ¹³C-labeled ATP to a cell lysate, we were able to determine the degree of in-source decay during an experiment. Analyzing a cell extract of the monocytic cell line THP-1 with [¹³C]ATP as internal standard, we were able to obtain values for the energy charge that were similar to those determined by a reference liquid chromatography electrospray ionization coupled to mass spectrometry (LC–ESI–MS) method.     

Characterization of DNA glycosylase activity by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

The DNA of all organisms is persistently damaged by endogenous reactive molecules. Most of the single-base endogenous damage is repaired through the base excision repair (BER) pathway that is initiated by members of the DNA glycosylase family. Although the BER pathway is often considered to proceed through a common abasic site intermediate, emerging evidence indicates that there are likely distinct branches reflected by the multitude of chemically different 3′ and 5′ ends generated at the repair site. In this study, we have applied matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI–TOF–MS) to the analysis of model DNA substrates acted on by recombinant glycosylases. We examine the chemical identity of several possible abasic site and nicked intermediates generated by monofunctional and bifunctional glycosylases. Our results suggest that the intermediate from endoIII/Nth might not be a simple β-elimination product as described previously. On the basis of ¹⁸O incorporation experiments, we propose a new mechanism for the endoIII/Nth family of glycosylases that may resolve several of the previous controversies. We further demonstrate that the use of an array of lesion-containing oligonucleotides can be used to rapidly examine the substrate preferences of a given glycosylase. Some of the lesions examined here can be acted on by more than one glycosylase, resulting in a spectrum of damaged intermediates for each lesion, suggesting that the sequence and coordination of repair activities that act on these lesions may influence the biological outcome of damage repair.     

Quantification of bifunctional diethylenetriaminepentaacetic acid derivative conjugation to monoclonal antibodies by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

The results of the characterization of a matrix-assisted laser desorption/ionization time-of-flight mass spectrometry-based method that was developed to establish the stoichiometry of CHX-A'-diethylenetriaminepentaacetic acid (DTPA) or benzyl-DTPA conjugated to a recombinant immunoglobulin G (IgG) are reported. This simple method does not require an accurate measurement of the sample protein concentration to accurately quantify the number of DTPA conjugated. It is also not necessary to thoroughly remove nonconjugated DTPA from the sample. The average number of moles of DTPA attached per mole of IgG was calculated from the difference in the observed masses of DTPA-IgG and nonconjugated IgG divided by the molecular weight of the DTPA derivative. As more DTPA is attached, the [M+H](+) peak of DTPA-IgG becomes broader and noisier. Also, the signal intensity in the mass spectrum decreases, apparently due to the increase in the heterogeneity in the number of DTPA attached to each molecule of IgG. The standard deviation of the measured mass and that of the stoichiometry of the DTPA attached per IgG increased as more DTPA was attached. The standard deviation, expressed as coefficient of variation for samples with 2 to 4 mol of DTPA attached per mole of IgG, was 8 to 9%.     

Distinctive characteristics of MALDI-Q/TOF and TOF/TOF tandem mass spectrometry for sequencing of permethylated complex type N-glycans

Concerted MALDI-MS profiling and CID MS/MS sequencing of permethylated glycans is one of the most effective approaches for high throughput glycomics applications. In essence, the identification of larger complex type N-glycans necessitates an unambiguous definition of any modification on the trimannosyl core and the complement of non-reducing terminal sequences which constitute the respective antennary structures. Permethylation not only affords analyses of both neutral and sialylated glycans at comparable ease and sensitivity but also yields more sequence-informative fragmentation pattern. Facile glycosidic cleavages directed mostly at N-acetylglucosamine under low energy CID, as implemented on a quadrupole/time-of-flight (Q/TOF) instrument, often afford multiple losses of the attached antenna resulting in characteristic ions related to the number of antennary branches on the trimannosyl core. Non-reducing terminal epitopes can be easily deduced but information on the linkage specific substituent on the terminal units is often missing. The high energy CID MS/MS afforded by TOF/TOF instrument can fill in the gap by giving an array of additional cross-ring and satellite ions. Glycosidic cleavages occurring specifically in concert with loss of 2-linked or 3-linked substituents provide an effective way to identify the branch-specific antennary extension. These characteristics are shown here to be effective in deriving the sequences of additionally galactosylated, sialylated and fucosylated terminal N-acetyllactosamine units and their antennary location. Together, a highly reproducible fragmentation pattern can be formulated to simplify spectral assignment. This work also provides first real examples of sequencing multiply sialylated complex type N-glycans by high energy CID on a TOF/TOF instrument. Shin-Yi Yu and Sz-Wei Wu contributed equally to this work. Dedicated to the late Prof. Yasuo Inoue, without whom the body of work represented by this article would not have been initiated in Taiwan.     

Peak quantification in surface-enhanced laser desorption/ionization by using mixture models

Surface-enhanced laser desorption/ionization (SELDI) time of flight (TOF) is a mass spectrometry technology for measuring the composition of a sampled protein mixture. A mass spectrum contains peaks corresponding to proteins in the sample. The peak areas are proportional to the measured concentrations of the corresponding proteins. Quantifying peak areas is difficult for existing methods because peak shapes are not constant across a spectrum and because peaks often overlap. We present a new method for quantifying peak areas. Our method decomposes a spectrum into peaks and a baseline using so-called statistical finite mixture models. We illustrate our method in detail on 8 samples from culture media of adipose tissue and globally on 64 samples from serum to compare our method to the standard Ciphergen method. Both methods give similar estimates for singleton peaks, but not for overlapping peaks. The Ciphergen method overestimates the heights of such peaks while our method still gives appropriate estimates. Peak quantification is an important step in pre-processing SELDI-TOF data and improvements therein will pay off in the later biomarker discovery phase.     

Analysis of derivatised steroids by matrix-assisted laser desorption/ionisation and post-source decay mass spectrometry

Neutral steroids are difficult to analyse using desorption ionisation methods coupled with mass spectrometry (MS). However, steroids with an unhindered ketone group can readily be derivatised with the Girard P (GP) reagent to give GP hydrazones. Steroid GP hydrazones contain a quaternary nitrogen atom and are readily desorbed in the matrix-assisted laser desorption/ionisation (MALDI) process, giving an improvement in sensitivity of two orders of magnitude. Steroids without a ketone group, but with a 3beta-hydroxy-Delta5 function, can be readily converted to 3-oxo-Delta4 steroids and subsequently derivatised to GP hydrazones for MALDI analysis. In addition to giving strong [M]+ ions upon MALDI, steroid GP hydrazones give informative post-source decay (PSD) spectra. By using the accurate mass of the precursor-ion measured by MALDI-MS, in combination with the structural information encoded in its PSD spectrum, steroid structures can readily be determined.     

Fungal pigments inhibit the matrix-assisted laser desorption/ionization time-of-flight mass spectrometry analysis of darkly pigmented fungi

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI–TOF MS) has been used to discriminate moniliaceous fungal species; however, darkly pigmented fungi yield poor fingerprint mass spectra that contain few peaks of low relative abundance. In this study, the effect of dark fungal pigments on the observed MALDI mass spectra was investigated. Peptide and protein samples containing varying concentrations of synthetic melanin or fungal pigments extracted from Aspergillus niger were analyzed by MALDI–TOF and MALDI–qTOF (quadrupole TOF) MS. Signal suppression was observed in samples containing greater than 250 ng/μl pigment. Microscopic examination of the MALDI sample deposit was usually heterogeneous, with regions of high pigment concentration appearing as black. Acquisition of MALDI mass spectra from these darkly pigmented regions of the sample deposit yielded poor or no [M+H]⁺ ion signal. In contrast, nonpigmented regions within the sample deposit and hyphal negative control extracts of A. niger were not inhibited. This study demonstrated that dark fungal pigments inhibited the desorption/ionization process during MALDI–MS; however, these fungi may be successfully analyzed by MALDI–TOF MS when culture methods that suppress pigment expression are used. The addition of tricyclazole to the fungal growth media blocks fungal melanin synthesis and results in less melanized fungi that may be analyzed by MALDI–TOF MS.     

A method for N-terminal de novo sequence analysis of proteins by matrix-assisted laser desorption/ionization mass spectrometry

A novel method for isolation and de novo sequencing of N-terminal peptides from proteins is described. The method presented here combines selective chemical tagging using succinimidyloxycarbonylmethyl tris(2,4,6-trimethoxyphenyl)phosphonium bromide (TMPP-Ac-OSu) at the N^α-amino group of peptides after digestion by metalloendopeptidase (from Grifola frondosa) and selective capture procedures using p-phenylenediisothiocyanate resin, by which the N-terminal peptide can be isolated, whether or not it is N-terminally blocked. The isolated N-terminal peptide modified N-terminally with TMPP-Ac-OSu reagent produces a simple fragmentation pattern under tandem mass spectrometric analysis to significantly facilitate sequencing.     

Structural characterization of N-linked oligosaccharides on monoclonal antibody cetuximab by the combination of orthogonal matrix-assisted laser desorption/ionization hybrid quadrupole-quadrupole time-of-flight tandem mass spectrometry and sequential enzymatic digestion

Cetuximab is a novel therapeutic monoclonal antibody with two N-glycosylation sites: a conserved site in the CH2 domain and a second site within the framework 3 of the variable portion of the heavy chain. The detailed structures of these oligosaccharides were successfully characterized using orthogonal matrix-assisted laser desorption/ionization hybrid quadrupole-quadrupole time-of-flight mass spectrometry (oMALDI Qq-TOF MS) and tandem mass spectrometry (MS/MS) in combination with exoglycosidase digestion. The N-linked oligosaccharides were released by treatment with N-glycanase F, reductively aminated with anthranilic acid, and fractionated by normal phase high-performance liquid chromatography (NP-HPLC). The fluorescent-labeled oligosaccharide pool and fractions were analyzed by oMALDI Qq-TOF MS and MS/MS in negative ion mode. Each fraction was further digested with an array of exoglycosidase mixtures, and subsequent MALDI TOF MS analysis of the resulting products yielded information about structural features of the oligosaccharide. The combined data revealed the presence of 21 distinct oligosaccharide structures in cetuximab. These oligosaccharides differ mainly in degree of sialylation with N-glycolyl neuraminic acid and extent of galactosylation (zero-, mono-, di-, and alpha(1-3)-galactosidase). The individual oligosaccharides were further assigned to the specific sites in the Fab and Fc regions of the antibody. This study represents a unique approach in that MS/MS data were used to identify and confirm the oligosaccharide structures of a protein.     

Discrimination of Francisella tularensis subspecies using surface enhanced laser desorption ionization mass spectrometry and multivariate data analysis

Francisella tularensis causes the zoonotic disease tularemia, and is considered a potential bioterrorist agent due to its extremely low infection dose and potential for airborne transmission. Presently, F. tularensis is divided into four subspecies; tularensis, holarctica, mediasiatica and novicida. Phenotypic discrimination of the closely related subspecies with traditional methods is difficult and tedious. Furthermore, the results may be vague and they often need to be complemented with virulence tests in animals. Here, we have used surface enhanced laser desorption ionization time-of-flight mass spectrometry (SELDI-TOF-MS) to discriminate between the four subspecies of F. tularensis. The method is based on the differential binding of protein subsets to chemically modified surfaces. Bacterial thermolysates were added to anionic, cationic, and copper ion-loaded immobilized metal affinity SELDI chip surfaces. After binding, washing, and SELDI-TOF-MS different protein profiles were obtained. The spectra generated from the different surfaces were then used to characterize each bacterial strain. The results showed that the method was reproducible, with an average intensity variation of 21%, and that the mass precision was good (300-450 ppm). Moreover, in subsequent cluster analysis and principal component analysis (PCA) data for the analyzed Francisella strains grouped according to the recognized subspecies. Partial least squares-discriminant analysis (PLS-DA) of the protein profiles also identified proteins that differed between the strains. Thus, the protein profiling approach based on SELDI-TOF-MS holds great promise for rapid high-resolution phenotypic identification of bacteria.     

Discrimination of Aspergillus isolates at the species and strain level by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry fingerprinting

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI–TOF MS) was used to generate highly reproducible mass spectral fingerprints for 12 species of fungi of the genus Aspergillus and 5 different strains of Aspergillus flavus. Prior to MALDI–TOF MS analysis, the fungi were subjected to three 1-min bead beating cycles in an acetonitrile/trifluoroacetic acid solvent. The mass spectra contain abundant peaks in the range of 5 to 20 kDa and may be used to discriminate between species unambiguously. A discriminant analysis using all peaks from the MALDI–TOF MS data yielded error rates for classification of 0 and 18.75% for resubstitution and cross-validation methods, respectively. If a subset of 28 significant peaks is chosen, resubstitution and cross-validation error rates are 0%. Discriminant analysis of the MALDI–TOF MS data for 5 strains of A. flavus using all peaks yielded error rates for classification of 0 and 5% for resubstitution and cross-validation methods, respectively. These data indicate that MALDI–TOF MS data may be used for unambiguous identification of members of the genus Aspergillus at both the species and strain levels.