Continuous solvent production from whey permeate using cells of Clostridium acetobutylicum immobilized by adsorption onto bonechar

Cells of Clostridium acetobutylicum were immobilized by adsorption onto bonechar and used in a packed bed reactor for the continuous production of solvents from whey permeate. A maximum solvent productivity of 4.1 g l⁻¹ h⁻¹, representing a yield of 0.23 g solvent/g lactose utilized, was observed at a dilution rate of 1.0 h⁻¹. The reactor was operated under stable conditions for 61 days. High concentrations of lactose in the whey permeate favored solventogenesis, while low concentrations favored acidogenesis.     

The effect of pH and lactose concentration on solvent production from whey permeate using Clostridium acetobutylicum

A study was performed to optimize the production of solvents from whey permeate in batch fermentation using Clostridium acetobutylicum P262. Fermentations performed at relatively low pH values resulted in high solvent yields and productivities, but lactose utilization was incomplete. At higher pH values, lactose utilization was improved but acid production dominated over solvent production. When operating at the higher pH values, an increase in the initial lactose concentration of the whey permeate resulted in lower rates of lactose utilization, and this was accompanied by increased solvent production and decreased acid production. Analysis of data from several experiments revealed a strong inverse relationship between solvent yield and lactose utilization rate. Thus, conditions which minimize the lactose utilization rate, such as low culture pH values or high initial lactose concentrations, favor solventogenesis at the expense of acid production.     

Integration of continuous production and recovery of solvents from whey permeate: use of immobilized cells of Clostridium acetobutylicum in a flutilized bed reactor coupled with gas stripping

An investigation was performed into the operation of an integrated system for continuous production and product recovery of solvents (acetone-butanol-ethanol) from the ABE fermentation process. Cells of Clostridium acetobutylicum were immobilized by adsorption onto bonechar, and used in a fluidized bed reactor for continuous solvent production from whey permeate. The reactor effluent was stripped of the solvents using nitrogen gas, and was recycled to the reactor. This relieved product inhibition and allowed further sugar utilization. At a dilution rate of 1.37 h^–1 a reactor productivity of 5.1 kg/(m³ · h) was achieved. The solvents in the stripping gas were condensed to give a solution of 53.7 kg/m³. This system has the advantages of relieving product inhibition, and providing a more concentrated solution for recovery by distillation. Residual sugar and non-volatile reaction intermediates are not removed by gas stripping and this contributes to high solvent yields.List of Symbols C kg/m³ Lactose concentration in reactor effluent - C _b kg/m³ Lactose concentration in bleed stream - C _c kg/m³ Lactose concentration in whey permeate feed - C _i kg/m³ Lactose concentration at reactor inlet - C _p kg/m³ Lactose concentration in condensed solvent stream (=0) - C _r kg/m³ Lactose concentration in recycle line (C _b=C _r) - C kg/h Amount of lactose utilized during certain time period - D h¹ Dilution rate of reactor, F _i/D=F/D - F dm³/h, m3/h F _i = Rate of feed flow to the reactor - F _b dm ³/h, m³/h Rate of bleed - F _c dm³/h, m³/h Rate of feed of whey permeate solution - F _p dm³/h, m³/h Rate of concentrated product removal - F _r dm³/h, m³/h Rate of recycle of stripped effluent to the reactor - P _l % Percent lactose utilization - R _l kg/(m³ · h) Overall lactose utilization rate - R _p kg/(m³ · h) Overall reactor (solvent) productivity - R _sl kg/h Rate of solvent loss - S kg/m³ Solvent concentration in reactor effluent - S _b kg/m³ Solvent concentration in bleed - S _c kg/m³ 0; Solvent concentration in concentrated whey permeate solution - S _i kg/m³ Solvent concentration at inlet of reactor - S _p kg/m³ Solvent concentration in concentrated product stream - S _r kg/m³ Solvent concentration in stripped effluent, S _r=S_b - S kg/h Amount of solvent produced from C amount of lactose in a particular time - ds/dt kg/(m³ · h) Rate of accumulation of solvents in the stripper - t h Time - V dm³, m³ Total reactor volume - V ¹ dm³, m³ Liquid volume in stripper - Y _P/S Solvent yield     

Use ofClostridium acetobutylicum P262 for production of solvents from whey permeate

Summary The production of solvents from whey permeate in batch fermentation usingClostridium acetobutylicum P262 was examined. An overall reactor productivity of 0.24 g/l.h was observed, representing a marked improvement over reports using other strains of clostridia. Using a semi-synthetic medium galactose was shown to be as effective a substrate as glucose. When whey permeate was used in which the lactose was hydrolysed prior to fermentation, preferential uptake of glucose over galactose was observed, and such hydrolysis provided no advantage to the fermentation process.     

Continuous production ofl-lactic acid from whey permeate by immobilizedLactobacillus casei subsp.casei

Summary The production of l-lactic acid from whey permeate, a waste product of the dairy industry, by fermentation with the lactic acid bacterium Lactobacillus casei subsp. casei was investigated. A fermentation medium consisting of permeate and supplements, which enables exponential growth of the organisms, was developed. A fast method for determination of free and immobilized biomass in solid-rich media, based on measurement of cellular ATP, was evolved. Continuous fermentations in a stirred tank reactor (STR) and in a fluidized bed reactor (FBR) with immobilized biomass were compared. In the STR a volumetric productivity of 5.5 g/l per hour at 100% substrate conversion [dilution rate (D) = 0.22 h^–1] was determined. In the FBR porous sintered glass beads were used for immobilization and a maximum biomass concentration of 105 g/kg support was measured. A productivity of 10 g/l per hour was obtained at D = 0.4 h^–1 (substrate conversion 93%) and of 13.5 g/l per hour at D = 1.0 h^–1 (substrate conversion 50%). Offprint requests to: W. Krischke     

Continuous butanol production from whey permeate with immobilized Clostridium beyerinckii LMD 27.6

Summary The aim of this study was to find the conditions necessary for the continuous butanol production from whey permeate with Clostridium beyerinckii LMD 27.6, immobilized in calcium alginate beads. The influence of three parameters on the butanol production was investigated: the fermentation temperature, the dilution rate (during start-up and at steady state) and the concentration of calcium ions in the fermentation broth. It was found that both a fermentation temperature of 30° C and a dilution rate of 0.1 h^-1 or less during the start-up phase are required to achieve continuous butanol production from whey permeate. Butanol can be produced continuously from whey permeate in reactor productivities sixteen times higher than those found in batch cultures with free C. beyerinckii cells on whey media.     

Continuous propionate production from whey permeate using a novel fibrous bed bioreactor

Continuous production of propionate from whey lactose by Propionibacterium acidipropionici immobilized in a novel fibrous bed bioreactor was studied. In conventional batch propionic acid fermentation, whey permeate without nutrient supplementation was unable to support cell growth and failed to give satisfactory fermentation results for over 7 days. However, with the fibrous bed bioreactor, a high fermentation rate and high conversion were obtained with plain whey permeate and de-lactose whey permeate. About 2% (wt/vol) propionic acid was obtained from a 4.2% lactose feed at a retention time of 35 to 45 h. The propionic acid yield was approximately 46% (wt/vol) from lactose. The optimal pH for fementation was 6.5, and lower fermentation rates and yields were obtained at lower pH values. The optimal temperature was 30 degrees C, but the temperature effect was not dramatic in the range of 25 to 35 degrees C. Addition of yeast extract and trypticase to whey permeate hastened reactor startup and increased the fermentation rate and product yields, but the addition was not required for long-term reactor performance. The improved fermentation results with the immobilized cell bioreactor can be attributed to the high cell density, approximately 50 g/L, attained in the bioreactor, Cells were immobilized by loose attachement to fiber surfaces and entrapment in the void spaces within the fibrous matrix, thus allowing constant renewal of cells. Consequently, this bioreactor was able to operate continuously for 6 months without encountering any clogging, degeneration, or contamination problems. Compared to conventional batch fermentors, the new bioreactor offers many advantages for industrial fermentation, including a more than 10-fold increase in productivity, acceptance of low-nutrient feedstocks such as whey permeate, and resistance to contamination. (c) 1994 John Wiley & Sons, Inc.     

In-line toxic product removal during solvent production by continuous fermentation using immobilized Clostridium acetobutylicum

Cells of Clostridium acetobutylicum were immobilized by adsorption onto bonechar, and used in a two-stage continuous reactor for solvent production from whey permeate. Gas-stripping (N₂ gas), an adsorbent resin (XAD-16) and a molecular sieve (silicalite) were evaluated for their use in between-stages solvent removal. All three techniques removed significant quantities of solvents, but not lactose, and allowed increases in sugar utilization and solvent productivity in the second stage. Gas stripping was the most successful technique, possibly because it removed only volatile solvents and not essential nutrients.     

Ethanol production from whey permeate by immobilized yeast cells

The ability of two yeast strains to utilize the lactose in whey permeate has been studied. Kluyveromyces marxianus NCYC 179 completely utilized the lactose (9.8%), whereas Saccharomyces cerevisiae NCYC 240 displayed an inability to metabolize whey lactose for ethanol production. Of the two gel matrices tested for immobilizing K. marxianus NCYC 179 cells, sodium alginate at 2% (w/v) concentration proved to be the optimum gel for entrapping the yeast cells effectively. The data on optimization of physiological conditions of fermentation (temperature, pH, ethanol concentration and substrate concentration) showed similar effects on immobilized and free cell suspensions of K. marxianus NCYC 179, in batch fermentation. A maximum yield of 42.6 g ethanol l^?1 (82% of theoretical) was obtained from 98 g lactose l^?1 when fermentation was carried at pH 5.5 and 30°C using 120 g dry weight l^?1 cell load of yeast cells. These results suggest that whey lactose can be metabolized effectively for ethanol production using immobilized K. marxianus NCYC 179 cells.     

Continuous production of lactic acid from whey permeate by Lactobacillus helveticus in two chemostats in series

The effect of dilution rate on the production of lactic acid from whey permeate by Lactobacillus helveticus has been investigated. In the first chemostat of a two-stage system, total conversion (98.1%) and maximum lactic acid concentration (43.7 g l⁻¹) were obtained at a dilution rate (D_Itot) of 0.06 h⁻¹. Maximum volumetric productivities of lactic acid (8.27 g l⁻¹ h⁻¹) and biomass (1.90 g l⁻¹ h⁻¹) occurred at D_Itot of 0.40 h⁻¹. The fraction of -lactate in the product was found to increase with dilution rate and reached a maximum of 66% at the same dilution rate. The maximum specific growth rate (μ_max) on this medium was 0.7 h⁻¹. A Y_ATP (max) value of 22.4 g dry weight (mol ATP)⁻¹ and a maintenance coefficient of 8.0 mmol ATP (g dry weight h)⁻¹ were determined. The second stage, in series with the first, confirmed these results and further showed that the total residence time could be reduced by 50%, compared with a single chemostat for the same nearly complete level of substrate conversion.     

Yeast biomass production from acid whey permeate

Summary The yield ofKluyveromyces marxianus Y-113 grown on sulphuric acid casein whey permeate was decreased at high lactose or ethanol concentrations and slightly increased with high agitation and supplementation of the permeate with nutrients. The maximum specific growth rate was most influenced by the stirrer speed, ethanol concentration and nutrient supplementation.     

Lactic acid production from whey permeate by immobilized Lactobacillus casei

Two matrices have been assessed for their ability to immobilize Lactobacillus casei cells for lactic acid fermentation in whey permeate medium. Agar at 2% concentration was found to be a better gel than polyacrylamide in its effectiveness to entrap the bacterial cells to carry out batch fermentation up to three repeat runs. Of the various physiological parameters studied, temperature and pH were observed to have no significant influence on the fermentation ability of the immobilized organism. A temperature range of 40–50°C and a pH range of 4.5–6.0 rather than specific values, were found to be optimum when fermentation was carried out under stationary conditions. In batch fermentation ～90% conversion of the substrate (lactose) was achieved in 48 h using immobilized cell gel cubes of 4 × 2 × 2 mm size, containing 400 mg dry bacterial cells per flask and 4.5% w/v (initial) whey lactose content as substrate. However, further increase in substrate levels tested (>4.5% w/v) did not improve the process efficiency. Supplementation of Mg²⁺ (1 mM) and agricultural by-products (mustard oil cake, 6%) in the whey permeate medium further improved the acid production ability of the immobilized cells under study.     

Microbial production of 2,3-butanediol from whey permeate

Summary Of four organisms tested in semi-synthetic medium for the production of 2,3-butanediol from lactose, Klebsiella pneumoniae N.C.I.B. 8017 proved to be the most promising. When tested using rennet whey permeate as substrate, a butanediol concentration of 7.5 g/l, representing a yield of 0.46 g/g lactose utilized, was observed after 96 h incubation. In whey permeate where the lactose had been hydrolysed enzymatically prior to the fermentation, a butanediol concentration of 13.7 g/l, representing a yield of 0.39 g/g sugar utilized was obtained. These results indicate that lactose utilization may be a limiting step in the fermentation process.     

Enhancing bioethanol production from delactosed whey permeate by upstream desalination techniques

Industrial cheese whey processing comprises generally the isolation of proteins and lactose, but the economic use for the residual molasses, the so‐called delactosed whey permeate (DWP), is still to be improved. One possibility to maximize valorization and to minimize waste water treatment is the conversion of the remaining lactose in the DWP to ethanol by the yeast Kluyveromyces marxianus. This fermentation process depends strongly on the total ash content of the DWP, as high salt concentrations inhibit yeast metabolism. Here, three different approaches were tested to lower the DWP salt content: (i) simple dilution; (ii) nanofiltration; and (iii) electrodialysis. Lactose consumption, ethanol production and time‐dependent yields were compared between the three methods. A dilution of DWP to 60% v/v led to fermentation taking less than 80 h and yield above 7% AbV (alcohol by volume). After nanofiltration, 7.5% AbV was produced in about 80 h, and after electrodialysis, 11% AbV was produced in about 52 h. On the one hand the technical treatments (nanofiltration and electrodialysis) led to enhanced productivity in the fermentations, but, on the other hand, elaborate and extensive preprocessing is needed. Overall, ethanol production from DWP could be enhanced by prior partial desalination.     

Butanol production from concentrated lactose/whey permeate: Use of pervaporation membrane to recover and concentrate product

In these studies, butanol (acetone butanol ethanol or ABE) was produced from concentrated lactose/whey permeate containing 211 g L^?1 lactose. Fermentation of such a highly concentrated lactose solution was possible due to simultaneous product removal using a pervaporation membrane. In this system, a productivity of 0.43 g L^?1 h^?1 was obtained which is 307 % of that achieved in a non-product removal batch reactor (0.14 g L^?1 h^?1) where approximately 60 g L^?1 whey permeate lactose was fermented. The productivity obtained in this system is much higher than that achieved in other product removal systems (perstraction 0.21 g L^?1 h^?1 and gas stripping 0.32 g L^?1 h^?1). This membrane was also used to concentrate butanol from approximately 2.50 g L^?1 in the reactor to 755 g L^?1. Using this membrane, ABE selectivities and fluxes of 24.4–44.3 and 0.57–4.05 g m^?2 h^?1 were obtained, respectively. Pervaporation restricts removal of water from the reaction mixture thus requiring significantly less energy for product recovery when compared to gas stripping.     

Xanthan production by Xanthomonas campestris using whey permeate medium

Xanthan gum is a polysaccharide that is widely used as stabilizer and thickener with many industrial applications in food industry. Our aim was to estimate the ability of Xanthomonas campestris ATCC 13951 for the production of xanthan gum by using whey as a growth medium, a by-product of dairy industry. X. campestris ATCC 13951 has been studied in batch cultures using a complex medium for the determination of the optimal concentration of glucose, galactose and lactose. In addition, whey was used under various treatment procedures (de-proteinated, partially hydrolyzed by β-lactamase and partially hydrolyzed and de-proteinated) as culture medium, to study the production of xanthan in a 2 l bioreactor with constant stirring and aeration. A production of 28 g/l was obtained when partially hydrolysed β-lactamase was used, which proved to be one of the highest xanthan gum production reported so far. At the same time, an effort has been made for the control and selection of the most appropriate procedure for the preservation of the strain and its use as inoculant in batch cultures, without loss of its viability and its capability of xanthan gum production. The pre-treatment of whey (whey permeate medium hydrolyzed, WPH) was very important for the production of xanthan by the strain X. campestris ATCC 13951 during batch culture conditions in a 2 l bioreactor. Preservation methods such as lyophilization, cryopreservation at various glycerol solution and temperatures have been examined. The results indicated that the best preservation method for the producing strain X. campestris ATCC 13951 was the lyophilization. Taking into account that whey permeate is a low cost by-product of the dairy industry, the production of xanthan achieved under the studied conditions was considered very promising for industrial application.     

The production of lactic acid from whey permeate byLactobacillus helveticus

Summary The effect of pH on growth and lactic acid production ofLactobacillus helveticus was investigated in a continuous culture using supplemented whey ultrafiltrate. Maximum lactate productivity of 5 gl^–1h^–1 occurred at pH 5.5. Whey permeates concentrated up to four times were fermented using batch cultures. Maximum lactic acid concentration of 95 gl^–1 was attained, but residual sugars indicated a possible limitation in growth factors.Nomenclature D Dilution rate [h^–1] - X Biomass [gl^–1] - Glu Glucose consentration [gl^–1] - Gal Galactose consentration [gl^–1] - S Substrate, Lactose consentration [gl^–1] - P Product, Lactate consentration [gl^–1] - Y_p/s Yield, defined as P/S [gg^–1] - r_i Rate of synthesis or consumption of i [gl^–1h^–1]     

Continous ethyl acetate production by Kluyveromyces fragilis on whey permeate

The synthesis of ethyl acetate by Kluyveromyces fragilis on diluted whey permeate was studied. Ethanol, lactose and O₂ are the direct precursors for ethyl acetate synthesis by this yeast. Ethyl acetate production is affected by many parameters, particularly the carbon/nitrogen (C/N) ratio, Tween 80 and iron. Ethyl acetate synthesis is optimum for C/N = 45. Tween 80 lowered slightly the level of ethyl acetate whereas iron completely stopped ethyl acetate production. The level of ethanol in the feed, the dissolved O₂ (DO) and dilution rate (D) were also optimised. Thus at D = 0.24 h ^–1, for 4 g/l of ethanol in the feed and 40% DO, the productivity of ethyl acetate was optimal (0.7 g/l per hour). Correspondence to: A. Miclo     

High-titer n-butanol production by clostridium acetobutylicum JB200 in fed-batch fermentation with intermittent gas stripping

Acetone–butanol–ethanol (ABE) fermentation with a hyper‐butanol producing Clostridium acetobutylicum JB200 was studied for its potential to produce a high titer of butanol that can be readily recovered with gas stripping. In batch fermentation without gas stripping, a final butanol concentration of 19.1 g/L was produced from 86.4 g/L glucose consumed in 78 h, and butanol productivity and yield were 0.24 g/L h and 0.21 g/g, respectively. In contrast, when gas stripping was applied intermittently in fed‐batch fermentation, 172 g/L ABE (113.3 g/L butanol, 49.2 g/L acetone, 9.7 g/L ethanol) were produced from 474.9 g/L glucose in six feeding cycles over 326 h. The overall productivity and yield were 0.53 g/L h and 0.36 g/g for ABE and 0.35 g/L h and 0.24 g/g for butanol, respectively. The higher productivity was attributed to the reduced butanol concentration in the fermentation broth by gas stripping that alleviated butanol inhibition, whereas the increased butanol yield could be attributed to the reduced acids accumulation as most acids produced in acidogenesis were reassimilated by cells for ABE production. The intermittent gas stripping produced a highly concentrated condensate containing 195.9 g/L ABE or 150.5 g/L butanol that far exceeded butanol solubility in water. After liquid–liquid demixing or phase separation, a final product containing ～610 g/L butanol, ～40 g/L acetone, ～10 g/L ethanol, and no acids was obtained. Compared to conventional ABE fermentation, the fed‐batch fermentation with intermittent gas stripping has the potential to reduce at least 90% of energy consumption and water usage in n‐butanol production from glucose. Biotechnol. Bioeng. 2012; 109: 2746–2756. © 2012 Wiley Periodicals, Inc.     

Model for continuous production of solvents from whey permeate in a packed bed reactor using cells of Clostridium acetobutylicum immobilized by adsorption onto bonechar

Summary A mathematical model has been developed to describe the operation of a packed bed reactor for the continuous production of solvents from whey permeate. The model has been used to quantitate the amounts of different physiological/ morphological types of biomass present in the reactor. The majority of biomass is inert, i.e. it neither grows nor produces solvent. Only relatively small amounts of biomass actively grow (vegetative, non-solvent-producing cells), while even smaller amounts are responsible for solvent production (clostridial, solvent-producing cells).