Liquid Norbornadiene Photoswitches for Solar Energy Storage

Due to high global energy demands, there is a great need for development of technologies for exploiting and storing solar energy. Closed cycle systems for storage of solar energy have been suggested, based on absorption of photons in photoresponsive molecules, followed by on‐demand release of thermal energy. These materials are called solar thermal fuels (STFs) or molecular solar thermal (MOST) energy storage systems. To achieve high energy densities, ideal MOST systems are required either in solid or liquid forms. In the case of the latter, neat high performing liquid materials have not been demonstrated to date. Here is presented a set of neat liquid norbornadiene derivatives for MOST applications and their characterization in toluene solutions and neat samples. Their synthesis is in most cases based on solvent‐free Diels‐Alder reactions, which easily and efficiently afford a range of compounds. The shear viscosity of the obtained molecules is close to that of colza oil, and they can absorb up to 10% of the solar spectrum with a measured energy storage density of up to 577 kJ/kg corresponding to 152 kJ mol^–1 (calculated 100 kJ mol^–1). These findings pave the way towards implementation of liquid norbornadienes in closed cycle energy storage technologies.     

Long‐Lasting Nanophosphors Applied to UV‐Resistant and Energy Storage Perovskite Solar Cells

Recently, considerable progress is achieved in lab prototype perovskite solar cells (PSCs); however, the stability of outdoor applications of PSCs remains a challenge due to the high sensitivity of perovskite material under moist and ultraviolet (UV) light conditions. In this work, the UV photostability of PSC devices is improved by incorporating a photon downshifting layer—SrAl₂O₄: Eu²⁺, Dy³⁺ (SAED)—prepared using the pulsed laser deposition approach. Light‐induced deep trap states in the photoactive layer are depressed, and UV light‐induced device degradation is inhibited after the SAED modification. Optimized power conversion efficiency (PCE) of 17.8% is obtained through the enhanced light harvesting and reduced carrier recombination provided by SAED. More importantly, a solar energy storage effect due to the long‐persistent luminescence of SAED is obtained after light illumination is turned off. The introduction of downconverting material with long‐persistent luminescence in PSCs not only represents a new strategy to improve PCE and light stability by photoconversion from UV to visible light but also provides a new paradigm for solar energy storage.     

Thirty Years of Luminescent Solar Concentrator Research: Solar Energy for the Built Environment

Research on the luminescent solar concentrator (LSC) over the past thirty‐odd years is reviewed. The LSC is a simple device at its heart, employing a polymeric or glass waveguide and luminescent molecules to generate electricity from sunlight when attached to a photovoltaic cell. The LSC has the potential to find extended use in an area traditionally difficult for effective use of regular photovoltaic panels: the built environment. The LSC is a device very flexible in its design, with a variety of possible shapes and colors. The primary challenge faced by the devices is increasing their photon‐to‐electron conversion efficiencies. A number of laboratories are working to improve the efficiency and lifetime of the LSC device, with the ultimate goal of commercializing the devices within a few years. The topics covered here relate to the efforts for reducing losses in these devices. These include studies of novel luminophores, including organic fluorescent dyes, inorganic phosphors, and quantum dots. Ways to limit the surface and internal losses are also discussed, including using organic and inorganic‐based selective mirrors which allow sunlight in but reflect luminophore‐emitted light, plasmonic structures to enhance emissions, novel photovoltaics, alignment of the luminophores to manipulate the path of the emitted light, and patterning of the dye layer to improve emission efficiency. Finally, some possible ‘glimpses of the future’ are offered, with additional research paths that could result in a device that makes solar energy a ubiquitous part of the urban setting, finding use as sound barriers, bus‐stop roofs, awnings, windows, paving, or siding tiles.     

GaSb‐Based Solar Cells for Full Solar Spectrum Energy Harvesting

In this work, a multijunction solar cell is developed on a GaSb substrate that can efficiently convert the long‐wavelength photons typically lost in a multijunction solar cell into electricity. A combination of modeling and experimental device development is used to optimize the performance of a dual junction GaSb/InGaAsSb concentrator solar cell. Using transfer printing, a commercially available GaAs‐based triple junction cell is stacked mechanically with the GaSb‐based materials to create a four‐terminal, five junction cell with a spectral response range covering the region containing >99% of the available direct‐beam power from the Sun reaching the surface of the Earth. The cell is assembled in a mini‐module with a geometric concentration ratio of 744 suns on a two‐axis tracking system and demonstrated a combined module efficiency of 41.2%, measured outdoors in Durham, NC. Taking into account the measured transmission of the optics gives an implied cell efficiency of 44.5%.     

Highly Efficient Polymer Tandem Cells and Semitransparent Cells for Solar Energy

Highly efficient tandem and semitransparent (ST) polymer solar cells utilizing the same donor polymer blended with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as active layers are demonstrated. A high power conversion efficiency (PCE) of 8.5% and a record high open‐circuit voltage of 1.71 V are achieved for a tandem cell based on a medium bandgap polymer poly(indacenodithiophene‐co‐phananthrene‐quinoxaline) (PIDT‐phanQ). In addition, this approach can also be applied to a low bandgap polymer poly[2,6‐(4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene)‐alt‐4,7‐(5‐fluoro‐2,1,3‐benzothia‐diazole)] (PCPDTFBT), and PCEs up to 7.9% are achieved. Due to the very thin total active layer thickness, a highly efficient ST tandem cell based on PIDT‐phanQ exhibits a high PCE of 7.4%, which is the highest value reported to date for a ST solar cell. The ST device also possesses a desirable average visible transmittance (≈40%) and an excellent color rendering index (≈100), permitting its use in power‐generating window applications.     

Graphene Based Materials: Enhancing Solar Energy Harvesting

Due to excellent electronic and optical properties as well as tunable work functions, graphene and graphene‐based materials are highly attractive for applications in enhancement of harvesting solar energy. In particular, they can be used as electron and hole transport materials, buffer layers, and window or/and counter electrodes in solar cells. This research news surveys very recent advances in this emerging field, with emphasis on fundamental understanding of their performance enhancement mechanisms for photovoltaic devices, and discusses future challenges.