Enhancing Cycle Stability of Lithium Iron Phosphate in Aqueous Electrolytes by Increasing Electrolyte Molarity

Aqueous lithium ion batteries (ALIBs) exhibit great potential to reduce the cost and improve the safety of rechargeable energy storage technologies. Lithium iron phosphate (LFP) cathodes have become a material of choice for many conventional, high power LIBs. However, experimental studies on LFP in aqueous lithium (Li) ion electrolytes are limited. Here, results of systematic studies are shown where it is demonstrated that the Li salt concentration of the aqueous electrolyte can significantly improve discharge capacity retention while minimally impacting rate capability, for electrodes made with a typical commercial sub‐micron sized LFP powder. Based on the postmortem analysis and the results of electrochemical characterization it is proposed that undesirable side reactions of aqueous electrolytes with LFP induce electrochemical separation of individual particles within the electrode, leading to the observed capacity fading. Increasing the salt concentration in aqueous solutions effectively reduces the concentration of water molecules in the electrolyte, which are mostly responsible for these undesirable side reactions. Similar trends observed with other cathode materials suggest that the use of concentrated aqueous electrolyte solutions offers an effective route to improve stability of aqueous Li ion batteries.     

Control and Optimization of the Electrochemical and Mechanical Properties of the Solid Electrolyte Interphase on Silicon Electrodes in Lithium Ion Batteries

The formation of the solid electrolyte interphase (SEI) on Si is examined in detail using several in situ techniques. The results show that employing different conditions during the first lithiation cycle produces SEI films with substantially different properties. Longer time at higher potentials produces softer SEI, whereas inorganic phases produced at lower potentials have higher elastic moduli. The SEI thickness stabilizes during the first cycle; however, the SEI resistance decreases during the first 20 cycles (in sharp contrast to typical surface passivation processes, where resistance is expected to increase with time). This behavior is consistent with the slow growth of inorganic constituents at lower potentials, inside of a mesoporous soft SEI that initially forms at higher potentials. This interpretation is based on the premise that these inorganic phases have a lower resistivity than that associated with electrolyte transport through the mesoporous organic phase. Based on this set of observations, the multiphase structure that evolves during initial cycling determines critical electrochemical and mechanical properties of the SEI. A basic model of these tradeoffs is proposed to provide guidelines for creating more stable interfacial films.     

Zwitterions for Organic/Perovskite Solar Cells,Light‐Emitting Devices,and Lithium Ion Batteries: Recent Progress and Perspectives

Zwitterions, a class of materials that contain covalently bonded cations and anions, have been extensively studied in the past decades owing to their special features, such as excellent solubility in polar solvents, for solution processing and dipole formation for the transfer of carriers and ions. Recently, zwitterions have been developed as electrode modifiers for organic solar cells (OSCs), perovskite solar cells (PVSCs), and organic light‐emitting devices (OLEDs), as well as electrolyte additives for lithium ion batteries (LIBs). With the rapid advances of zwitterionic materials, high‐performance devices have been constructed with enhanced efficiencies by introducing them as interface layers and electrolyte additives. In this review, recent progress in OSCs, PVSCs, OLEDs, and LIBs by using zwitterions is highlighted. The authors also elaborate the role of various zwitterionic materials as interfacial layers and additives for highly efficient OSCs, PVSCs, OLEDs, and LIBs. This article presents an overview of device performance of zwitterionic materials. The structure–property relationship is also discussed. Finally, the prospects of zwitterion materials are also addressed.     

Interface Engineering for Lithium Metal Anodes in Liquid Electrolyte

Interfacial chemistry between lithium metal anodes and electrolytes plays a vital role in regulating the Li plating/stripping behavior and improving the cycling performance of Li metal batteries. Constructing a stable solid electrolyte interphase (SEI) on Li metal anodes is now understood to be a requirement for progress in achieving feasible Li‐metal batteries. Recently, the application of novel analytical tools has led to a clearer understanding of composition and the fine structure of the SEI. This further promoted the development of interface engineering for stable Li metal anodes. In this review, the SEI formation mechanism, conceptual models, and the nature of the SEI are briefly summarized. Recent progress in probing the atomic structure of the SEI and elucidating the fundamental effect of interfacial stability on battery performance are emphasized. Multiple factors including current density, mechanical strength, operating temperature, and structure/composition homogeneity that affect the interfacial properties are comprehensively discussed. Moreover, strategies for designing stable Li‐metal/electrolyte interfaces are also reviewed. Finally, new insights and future directions associated with Li‐metal anode interfaces are proposed to inspire more revolutionary solutions toward commercialization of Li metal batteries.     

Aqueous Electrochemical Energy Storage with a Mediator‐Ion Solid Electrolyte

This study presents a battery concept with a “mediator‐ion” solid electrolyte for the development of next‐generation electrochemical energy storage technologies. The active anode and cathode materials in a single cell can be in the solid, liquid, or gaseous form, which are separated by a sodium‐ion solid‐electrolyte separator. The uniqueness of this mediator‐ion strategy is that the redox reactions at the anode and the cathode are sustained by a shuttling of a mediator sodium ion between the anolyte and the catholyte through the solid‐state electrolyte. Use of the solid‐electrolyte separator circumvents the chemical‐crossover problem between the anode and the cathode, overcomes the dendrite‐problem when employing metal‐anodes, and offers the possibility of using different liquid electrolytes at the anode and the cathode in a single cell. The battery concept is demonstrated with two low‐cost metal anodes (zinc and iron), two liquid cathodes (bromine and potassium ferricyanide), and one gaseous cathode (air/O₂) with a sodium‐ion solid electrolyte. This novel battery strategy with a mediator‐ion solid electrolyte is applicable to a wide range of electrochemical energy storage systems with a variety of cathodes, anodes, and mediator‐ion solid electrolytes.     

High and Reversible Lithium Ion Storage in Self‐Exfoliated Triazole‐Triformyl Phloroglucinol‐Based Covalent Organic Nanosheets

Covalent organic framework (COF) can grow into self‐exfoliated nanosheets. Their graphene/graphite resembling microtexture and nanostructure suits electrochemical applications. Here, covalent organic nanosheets (CON) with nanopores lined with triazole and phloroglucinol units, neither of which binds lithium strongly, and its potential as an anode in Li‐ion battery are presented. Their fibrous texture enables facile amalgamation as a coin‐cell anode, which exhibits exceptionally high specific capacity of ≈720 mA h g^?1 (@100 mA g^?1). Its capacity is retained even after 1000 cycles. Increasing the current density from 100 mA g^?1 to 1 A g^?1 causes the specific capacity to drop only by 20%, which is the lowest among all high‐performing anodic COFs. The majority of the lithium insertion follows an ultrafast diffusion‐controlled intercalation (diffusion coefficient, D_Li⁺ = 5.48 × 10^?11 cm² s^?1). The absence of strong Li‐framework bonds in the density functional theory (DFT) optimized structure supports this reversible intercalation. The discrete monomer of the CON shows a specific capacity of only 140 mA h g^?1 @50 mA g^?1 and no sign of lithium intercalation reveals the crucial role played by the polymeric structure of the CON in this intercalation‐assisted conductivity. The potentials mapped using DFT suggest a substantial electronic driving‐force for the lithium intercalation. The findings underscore the potential of the designer CON as anode material for Li‐ion batteries.     

Predicting Calendar Aging in Lithium Metal Secondary Batteries: The Impacts of Solid Electrolyte Interphase Composition and Stability

Calendar aging of lithium metal batteries, in which cells' components degrade internally due to chemical reactions while no current is being applied, is a relatively unstudied field. In this work, a model to predict calendar aging of lithium metal cells is developed using two sets of readily obtainable data: solid electrolyte interphase (SEI) layer composition (measured via X‐ray photoelectron spectroscopy) and SEI stability (measured as a degradation rate using a simple constant current–constant voltage charging protocol). Electrolyte properties such as volume and salt concentration are varied in order to determine their effect on SEI stability and composition, with subsequent impacts to calendar aging. Lower salt concentrations produce a solvent‐based, more soluble SEI, while the highest concentration produces a salt‐based, less soluble SEI. Higher electrolyte volumes promote dissolution of the SEI and thus decrease its stability. The model predicts that lithium metal would be the limiting factor in calendar aging, depleting long before the electrolyte does. Additionally, the relative composition of the electrolyte during aging is modeled and found to eventually converge to the same value independent of initial salt concentration.     

Na‐Ion Batteries for Large Scale Applications: A Review on Anode Materials and Solid Electrolyte Interphase Formation

The urgent need for optimizing the available energy through smart grids and efficient large‐scale energy storage systems is pushing the construction and deployment of Li‐ion batteries in the MW range which, in the long term, are expected to hit the GW dimension while demanding over 1000 ton of positive active material per system. This amount of Li‐based material is equivalent to almost 1% of current Li consumption and can strongly influence the evolution of the lithium supply and cost. Given this uncertainty, it becomes mandatory to develop an energy storage technology that depends on almost infinite and widespread resources: Na‐ion batteries are the best technology for large‐scale applications. With small working cells in the market that cannot compete in cost ($/W h) with commercial Li‐ion batteries, the consolidation of Na‐ion batteries mainly depends on increasing their energy density and stability, the negative electrodes being at the heart of these two requirements. Promising Na‐based negative electrodes for large‐scale battery applications are reviewed, along with the study of the solid electrolyte interphase formed in the anode surface, which is at the origin of most of the stability problems.     

Thermally Durable Lithium‐Ion Capacitors with High Energy Density from All Hydroxyapatite Nanowire‐Enabled Fire‐Resistant Electrodes and Separators

The reliability and durability of lithium‐ion capacitors (LICs) are severely hindered by the kinetic imbalance between capacitive and Faradaic electrodes. Efficient charge storage in LICs is still a huge challenge, particularly for thick electrodes with high mass loading, fast charge delivery, and harsh working conditions. Here, a unique thermally durable, stable LIC with high energy density from all‐inorganic hydroxyapatite nanowire (HAP NW)‐enabled electrodes and separators is reported. Namely, the LIC device is designed and constructed with the electron/ion dual highly conductive and fire‐resistant composite Li₄Ti₅O₁₂‐based anode and activated carbon‐based cathode, together with a thermal‐tolerant HAP NW separator. Despite the thick‐electrode configuration, the as‐fabricated all HAP NW‐enabled LIC exhibits much enhanced electrochemical kinetics and performance, especially at high current rates and temperatures. Long cycling lifetime and state‐of‐the‐art areal energy density (1.58 mWh cm^?2) at a high mass loading of 30 mg cm^?2 are achieved. Benefiting from the excellent fire resistance of HAP NWs, such an unusual LIC exhibits high thermal durability and can work over a wide range of temperatures from room temperature to 150 °C. Taking full advantage of synergistic configuration design, this work sets the stage for designing advanced LICs beyond the research of active materials.     

Operando Lithium Dynamics in the Li‐Rich Layered Oxide Cathode Material via Neutron Diffraction

Neutron diffraction under operando battery cycling is used to study the lithium and oxygen dynamics of high Li‐rich Li(Li_x/3Ni_(3/8‐3x/8)Co_(1/4‐x/4)Mn_(3/8+7x/24)O₂ (x = 0.6, HLR) and low Li‐rich Li(Li_x/3Ni_(1/3‐x/3)Co_(1/3‐x/3)Mn_(1/3+x/3)O₂ (x = 0.24, LLR) compounds that exhibit different degrees of oxygen activation at high voltage. The measured lattice parameter changes and oxygen position show largely contrasting changes for the two cathodes where the LLR exhibits larger movement of oxygen and lattice contractions in comparison to the HLR that maintains relatively constant lattice parameters and oxygen position during the high voltage plateau until the end of charge. Density functional theory calculations show the presence of oxygen vacancy during the high voltage plateau; changes in the lattice parameters and oxygen position are consistent with experimental observations. Lithium migration kinetics for the Li‐rich material is observed under operando conditions for the first time to reveal the rate of lithium extraction from the lithium layer, and transition metal layer is related to the different charge and discharge characteristics. At the beginning of charging, the lithium extraction predominately occurs within the lithium layer. Once the high voltage plateau is reached, the lithium extraction from the lithium layer slows down and extraction from the transition metal layer evolves at a faster rate.     

Synthesis and Characterization of Lithium Bis(fluoromalonato)borate for Lithium‐Ion Battery Applications

A new orthochelated salt, lithium bis(monofluoromalonato)borate (LiBFMB), is synthesized and purified for application in lithium‐ion batteries. The presence of fluorine in the borate anion of LiBFMB increases its oxidation potential and also facilitates ion dissociation, as reflected by the ratio of ionic conductivity (σ_exp) and ion diffusivity coefficients (σ_NMR). Half‐cell tests using 5.0 V lithium nickel manganese oxide (LiNi_0.5Mn_1.5O₄) as a cathode and ethylene carbonate (EC)/dimethyl carbonate (DMC)/diethyl carbonate (DEC) as a solvent reveals that the impedance of the LiBFMB cell is much larger than those of LiPF₆‐ and lithium bis(oxalato)borate (LiBOB)‐based cells, which results in lower capacity and poor cycling performance of the former. X‐ray photoelectron spectroscopy (XPS) results for the cycled cathode electrode suggest that because of the stability of the LiBFMB salt, the solid electrolyte interphase (SEI) formed on the cathode surface is significantly different from those of LiPF₆ and LiBOB based electrolytes, resulting in more solvent decomposition and a thicker SEI layer. Initial results also indicate that using a high dielectric constant solvent, propylene carbonate, alters the surface chemistry, reduces the interfacial impedance, and enhances the performance of LiBFMB‐based 5.0 V cell.     

An All‐Organic Non‐aqueous Lithium‐Ion Redox Flow Battery

A non‐aqueous lithium‐ion redox flow battery employing organic molecules is proposed and investigated. 2,5‐Di‐tert‐butyl‐1,4‐bis(2‐methoxyethoxy)benzene and a variety of molecules derived from quinoxaline are employed as initial high‐potential and low‐potential active materials, respectively. Electrochemical measurements highlight that the choice of electrolyte and of substituent groups can have a significant impact on redox species performance. The charge‐discharge characteristics are investigated in a modified coin‐cell configuration. After an initial break‐in period, coulombic and energy efficiencies for this unoptimized system are ～70% and ～37%, respectively, with major charge and discharge plateaus between 1.8‐2.4 V and 1.7‐1.3 V, respectively, for 30 cycles. Performance enhancements are expected with improvements in cell design and materials processing.     

Understanding the Degradation Mechanisms of LiNi0.5Co0.2Mn0.3O2 Cathode Material in Lithium Ion Batteries

LiNi_xCo_yMn_zO₂ (NCM, 0 ≤ x,y,z < 1) has become one of the most important cathode materials for next‐generation lithium (Li) ion batteries due to its high capacity and cost effectiveness compared with LiCoO₂. However, the high‐voltage operation of NCM (>4.3 V) required for high capacity is inevitably accompanied by a more rapid capacity fade over numerous cycles. Here, the degradation mechanisms of LiNi_0.5Co_0.2Mn_0.3O₂ are investigated during cycling under various cutoff voltage conditions. The surface lattice structures of LiNi_0.5Co_0.2Mn_0.3O₂ are observed to suffer from an irreversible transformation; the type of transformation depends on the cutoff voltage conditions. The surface of the pristine rhombohedral phase tends to transform into a mixture of spinel and rock salt phases. Moreover, the formation of the rock salt phase is more dominant under a higher voltage operation (≈4.8 V), which is attributable to the highly oxidative environment that triggers the oxygen loss from the surface of the material. The presence of the ionically insulating rock salt phase may result in sluggish kinetics, thus deteriorating the capacity retention. This implies that the prevention of surface structural degradation can provide the means to produce and retain high capacity, as well as stabilize the cycle life of LiNi_0.5Co_0.2Mn_0.3O₂ during high‐voltage operations.     

Fundamentals and Challenges of Lithium Ion Batteries at Temperatures between −40 and 60 °C

Lithium ion batteries (LIBs) continuously prove themselves to be the main power source in consumer electronics and electric vehicles. To ensure environmental sustainability, LIBs must be capable of performing well at extreme temperatures, that is, between ?40 and 60 °C. In this review, the recent important progress and advances in the subzero and elevated temperature operations of LIBs is comprehensively summarized from a materials perspective. In the scenario of subzero temperatures, limitations, electrolytes, anodes, and solid electrolyte interphase (SEI); cathodes and cathode electrolyte interphase (CEI); and binders are thoroughly discussed to explore the fundamentals and basics that underlie the decay in electrochemical performance and how the chemistry, physics, and electrochemistry are correlated with the materials and components that interact with each other. In the case of high temperatures limitations, the thermal stability of the key materials and components are reviewed, and then the reaction thermodynamics and kinetics of the anodes, cathodes, electrolytes, and their interactions are described using the highest occupied molecular orbit (HOMO)/lowest unoccupied molecular orbit (LUMO), and are extensively discussed. The prospect of combining the extreme temperature poles in a single cell by introducing appropriate electrolytes and additives is discussed.