Simultaneous Contact and Grain‐Boundary Passivation in Planar Perovskite Solar Cells Using SnO2‐KCl Composite Electron Transport Layer

The performance of perovskite solar cells is sensitive to detrimental defects, which are prone to accumulate at the interfaces and grain boundaries of bulk perovskite films. Defect passivation at each region will lead to reduced trap density and thus less nonradiative recombination loss. However, it is challenging to passivate defects at both the grain boundaries and the bottom charge transport layer/perovskite interface, mainly due to the solvent incompatibility and complexity in perovskite formation. Here SnO₂‐KCl composite electron transport layer (ETL) is utilized in planar perovskite solar cells to simultaneously passivate the defects at the ETL/perovskite interface and the grain boundaries of perovskite film. The K and Cl ions at the ETL/perovskite interface passivate the ETL/perovskite contact. Meanwhile, K ions from the ETL can diffuse through the perovskite film and passivate the grain boundaries. An enhancement of open‐circuit voltage from 1.077 to 1.137 V and a corresponding power conversion efficiency increasing from 20.2% to 22.2% are achieved for the devices using SnO₂‐KCl composite ETL. The composite ETL strategy reported herein provides an avenue for defect passivation to further increase the efficiency of perovskite solar cells.     

Efficient Defect Passivation for Perovskite Solar Cells by Controlling the Electron Density Distribution of Donor‐π‐Acceptor Molecules

Organic–inorganic hybrid perovskite solar cells (PSCs) are a promising photovoltaic technology that has rapidly developed in recent years. Nevertheless, a large number of ionic defects within perovskite absorber can serve as non‐radiative recombination center to limit the performance of PSCs. Here, organic donor‐π‐acceptor (D‐π‐A) molecules with different electron density distributions are employed to efficiently passivate the defects in the perovskite films. The X‐ray photoelectron spectroscopy (XPS) analysis shows that the strong electron donating N,N‐dibutylaminophenyl unit in a molecule causes an increase in the electron density of the passivation site that is a carboxylate group, resulting in better binding with the defects of under‐coordinated Pb²⁺ cations. Carrier lifetime in the perovskite films measured by the time‐resolved photoluminescence spectrum is also prolonged by an increase in donation ability of the D‐π‐A molecules. As a consequence, these benefits contribute to an increase of 80 mV in the open circuit voltage of the devices, enabling a maximum power conversion efficiency (PCE) of 20.43%, in comparison with PCE of 18.52% for the control device. The authors' findings provide a novel strategy for efficient defect passivation in the perovskite solar cells based on controlling the electronic configuration of passivation molecules.     

p‐Type CuI Islands on TiO2 Electron Transport Layer for a Highly Efficient Planar‐Perovskite Solar Cell with Negligible Hysteresis

Compact TiO₂ is widely used as an electron transport material in planar‐perovskite solar cells. However, TiO₂‐based planar‐perovskite solar cells exhibit low efficiencies due to intrinsic problems such as the unsuitable conduction band energy and low electron extraction ability of TiO₂. Herein, the planar TiO₂ electron transport layer (ETL) of perovskite solar cells is modified with ionic salt CuI via a simple one‐step spin‐coating process. The p‐type nature of the CuI islands on the TiO₂ surface leads to modification of the TiO₂ band alignment, resulting in barrier‐free contacts and increased open‐circuit voltage. It is found that the polarity of the CuI‐modified TiO₂ surface can pull electrons to the interface between the perovskite and the TiO₂, which improves electron extraction and reduces nonradiative recombination. The CuI solution concentration is varied to control the electron extraction of the modified TiO₂ ETL, and the optimized device shows a high efficiency of 19.0%. In addition, the optimized device shows negligible hysteresis, which is believed to be due to the removal of trap sites and effective electron extraction by CuI‐modified TiO₂. These results demonstrate the hitherto unknown effect of p‐type ionic salts on electron transport material.     

Inorganic CsPbI3 Perovskite Coating on PbS Quantum Dot for Highly Efficient and Stable Infrared Light Converting Solar Cells

Solution‐processed colloidal quantum dot (CQD) solar cells harvesting the infrared part of the solar spectrum are especially interesting for future use in semitransparent windows or multilayer solar cells. To improve the device power conversion efficiency (PCE) and stability of the solar cells, surface passivation of the quantum dots is vital in the research of CQD solar cells. Herein, inorganic CsPbI₃ perovskite (CsPbI₃‐P) coating on PbS CQDs with a low‐temperature, solution‐processed approach is reported. The PbS CQD solar cell with CsPbI₃‐P coating gives a high PCE of 10.5% and exhibits remarkable stability both under long‐term constant illumination and storage under ambient conditions. Detailed characterization and analysis reveal improved passivation of the PbS CQDs with the CsPbI₃‐P coating, and the results suggest that the lattice coherence between CsPbI₃‐P and PbS results in epitaxial induced growth of the CsPbI₃‐P coating. The improved passivation significantly diminishes the sub‐bandgap trap‐state assisted recombination, leading to improved charge collection and therefore higher photovoltaic performance. This work therefore provides important insight to improve the CQD passivation by coating with an inorganic perovskite ligand for photovoltaics or other optoelectronic applications.     

Soft Template‐Controlled Growth of High‐Quality CsPbI3 Films for Efficient and Stable Solar Cells

The unfavorable morphology and inefficient utilization of phase transition reversibility have limited the high‐temperature‐processed inorganic perovskite films in both efficiency and stability. Here, a simple soft template‐controlled growth (STCG) method is reported by introducing (adamantan‐1‐yl)methanammonium to control the nucleation and growth rate of CsPbI₃ crystals, which gives rise to pinhole‐free CsPbI₃ film with a grain size on a micrometer scale. The STCG‐based CsPbI₃ perovskite solar cell exhibits a power conversion efficiency of 16.04% with significantly reduced defect densities and charge recombination. More importantly, an all‐inorganic solar cell with the architecture fluorine‐doped tin oxide (FTO)/NiO_x/STCG‐CsPbI₃/ZnO/indium‐doped tin oxide (ITO) is successfully fabricated to demonstrate its real advantage in thermal stability. By suppressing the inductive effect of defects during the phase transition and utilizing the unique reversibility of the phase transition for the high‐temperature‐processed CsPbI₃ film, the all‐inorganic solar cell retains 90% of its initial efficiency after 3000 h of continuous light soaking and heating.     

Efficient Perovskite Solar Cells by Reducing Interface‐Mediated Recombination: a Bulky Amine Approach

The presence of non‐radiative recombination at the perovskite surface/interface limits the overall efficiency of perovskite solar cells (PSCs). Surface passivation has been demonstrated as an efficient strategy to suppress such recombination in Si cells. Here, 1‐naphthylmethylamine iodide (NMAI) is judiciously selected to passivate the surface of the perovskite film. In contrast to the popular phenylethylammonium iodide, NMAI post‐treatment primarily leaves NMAI salt on the surface of the perovskite film. The formed NMAI layer not only efficiently decreases the defect‐assisted recombination for chemical passivation, but also retards the charge accumulation of energy level mis‐alignment for vacuum level bending and prevents minority carrier recombination due to the charge‐blocking effect. Consequently, planar PSCs with high efficiency of 21.04% and improved long‐term stability (98.9% of the initial efficiency after 3240 h) are obtained. Moreover, open‐circuit voltage as high as 1.20 V is achieved at the absorption threshold of 1.61 eV, which is among the highest reported values in planar PSCs. This work provides new insights into the passivation mechanisms of organic ammonium salts and suggests future guidelines for developing improved passivation layers.     

MACl‐Assisted Ge Doping of Pb‐Hybrid Perovskite: A Universal Route to Stabilize High Performance Perovskite Solar Cells

Interfacial engineering, grain boundary, and surface passivation in organic–inorganic hybrid perovskite solar cells (HyPSCs) are effective in achieving high performance and enhanced durability. Organic additives and inorganic doping are generally used to chemically modify the surface contacting charge transport layers, and/or grain boundaries so as to reduce the defect density. Here, a simple but tricky one‐step method to dope organic–inorganic hybrid perovskite with Ge for the first time is reported. Unlike Ge doping to all‐inorganic perovskites, application of GeI₂ in organic–inorganic perovskite precursors is challenging due to the extremely poor solubility of GeI₂ in hybrid perovskite ink, leading to failure in the formation of uniform films. However, it is found that addition of methylammonium chloride (MACl) into the precursor remarkably increases the solubility of GeI₂. This MACl‐assisted Ge doping of hybrid perovskites produces high‐quality crystalline film with its surface passivated with nonvolatile GeI₂ (GeO₂) and the volatile MACl additive also improves the uniformity of GeO₂ distribution in the perovskite films. The resulting Ge‐doped mixed cation and mixed halide perovskite films with composition FA_0.83MA_0.17Ge_0.03Pb_0.97(I_0.9Br_0.1)₃ show superior photoluminescence lifetime, power conversion efficiency above 22%, and greater stability toward illumination and humidity, outperforming photovoltaic properties of HyPSCs prepared without the Ge doping.     

Room‐Temperature Vapor Deposition of Cobalt Nitride Nanofilms for Mesoscopic and Perovskite Solar Cells

Organic/inorganic hybrid solar cells, typically mesoscopic and perovskite solar cells, are regarded as promising candidates to replace conventional silicon or thin film photovoltaics. There have been intensive investigations on the development of advanced materials for improved power conversion efficiencies, however, economical feasibilities and reliabilities of the organic/inorganic photovoltaics are yet to reach at a sufficient level for practical utilizations. In this study, cobalt nitride (CoN) nanofilms prepared by room‐temperature vapor deposition in an inert N₂ atmosphere, which is a facile and highly reproducible procedure, are proposed as a low‐cost counter electrode in mesoscopic dye‐sensitized solar cells (DSCs) and a hole transport material in inverted planar perovskite solar cells (PSCs) for the first time. The CoN film successfully replaces conventional Pt in DSCs, resulting in a power conversion efficiency comparable to the ones based on Pt. In addition, PSCs employing the CoN manifest high efficiency even up to 15.0%, which is comparable to state‐of‐the‐art performance in the cases of PSCs employing inorganic hole transporters. Furthermore, flexible solar cell applications of the CoN are performed in both mesoscopic and perovskite solar cells, verifying the advantages of the room‐temperature deposition process and feasibilities of the CoN nanofilms in various fields.     

Efficient Passivation of Hybrid Perovskite Solar Cells Using Organic Dyes with COOH Functional Group

Organic–inorganic halide perovskites are efficient absorbers for solar cells. Nevertheless, the trap states at the surfaces and grain boundaries are a detrimental factor compromising the device performance. Here, an organic dye (AQ310) is employed as passivator to reduce the trap states of the perovskites and promote better stability. The results demonstrate that the trap states of perovskite are minimized by the presence of AQ310's ?COOH group and the formation of coordination with under‐coordinated Pb²⁺ ions. The resulting carrier recombination time is prolonged and verified by the photoluminescence and open‐circuit voltage decay measurements. Consequently, the best average power conversion efficiency (PCE) of 19.43% is achieved for the perovskite solar cell (PSC) with AQ310 passivation, as compared with a low average PCE of 17.98% for the PSC without AQ310 passivation.     

Elucidating the Role of a Tetrafluoroborate‐Based Ionic Liquid at the n‐Type Oxide/Perovskite Interface

Halide perovskites are currently one of the most heavily researched emerging photovoltaic materials. Despite achieving remarkable power conversion efficiencies, perovskite solar cells have not yet achieved their full potential, with the interfaces between the perovskite and the charge‐selective layers being where most recombination losses occur. In this study, a fluorinated ionic liquid (IL) is employed to modify the perovskite/SnO₂ interface. Using Kelvin probe and photoelectron spectroscopy measurements, it is shown that depositing the perovskite onto an IL‐treated substrate results in the crystallization of a perovskite film which has a more n‐type character, evidenced by a decrease of the work function and a shift of the Fermi level toward the conduction band. Photoluminescence spectroscopy and time‐resolved microwave conductivity are used to investigate the optoelectronic properties of the perovskite grown on neat and IL‐modified surfaces and it is found that the modified substrate yields a perovskite film which exhibits an order of magnitude lower trap density than the control. When incorporated into solar cells, this interface modification results in a reduction in the current–voltage hysteresis and an improvement in device performance, with the best performing devices achieving steady‐state PCEs exceeding 20%.     

Inverted Current–Voltage Hysteresis in Mixed Perovskite Solar Cells: Polarization,Energy Barriers,and Defect Recombination

Organic‐inorganic metal halide perovskite solar cells show hysteresis in their current–voltage curve measured at a certain voltage sweep rate. Coinciding with a slow transient current response, the hysteresis is attributed to a slow voltage‐driven (ionic) charge redistribution in the perovskite solar cell. Thus, the electric field profile and in turn the electron/hole collection efficiency become dependent on the biasing history. Commonly, a positive prebias is beneficial for a high power‐conversion efficiency. Fill factor and open‐circuit voltage increase because the prebias removes the driving force for charge to pile‐up at the electrodes, which screen the electric field. Here, it is shown that the piled‐up charge can also be beneficial. It increases the probability for electron extraction in case of extraction barriers due to an enhanced electric field allowing for tunneling or dipole formation at the perovskite/electrode interface. In that case, an inverted hysteresis is observed, resulting in higher performance metrics for a voltage sweep starting at low prebias. This inverted hysteresis is particularly pronounced in mixed‐cation mixed‐halide systems which comprise a new generation of perovskite solar cells that makes it possible to reach power‐conversion efficiencies beyond 20%.     

Interface Engineering for Highly Efficient and Stable Planar p‐i‐n Perovskite Solar Cells

Organic‐inorganic halide perovskite materials have become a shining star in the photovoltaic field due to their unique properties, such as high absorption coefficient, optimal bandgap, and high defect tolerance, which also lead to the breathtaking increase in power conversion efficiency from 3.8% to over 22% in just seven years. Although the highest efficiency was obtained from the TiO₂ mesoporous structure, there are increasing studies focusing on the planar structure device due to its processibility for large‐scale production. In particular, the planar p‐i‐n structure has attracted increasing attention on account of its tremendous advantages in, among other things, eliminating hysteresis alongside a competitive certified efficiency of over 20%. Crucial for the device performance enhancement has been the interface engineering for the past few years, especially for such planar p‐i‐n devices. The interface engineering aims to optimize device properties, such as charge transfer, defect passivation, band alignment, etc. Herein, recent progress on the interface engineering of planar p‐i‐n structure devices is reviewed. This review is mainly focused on the interface design between each layer in p‐i‐n structure devices, as well as grain boundaries, which are the interfaces between polycrystalline perovskite domains. Promising research directions are also suggested for further improvements.     

Molecular Engineered Hole‐Extraction Materials to Enable Dopant‐Free,Efficient p‐i‐n Perovskite Solar Cells

Two hole‐extraction materials (HEMs), TPP‐OMeTAD and TPP‐SMeTAD, have been developed to facilitate the fabrication of efficient p‐i‐n perovskite solar cells (PVSCs). By replacing the oxygen atom on HEM with sulfur (from TPP‐OMeTAD to TPP‐SMeTAD), it effectively lowers the highest occupied molecular orbital of the molecule and provides stronger Pb? S interaction with perovskites, leading to efficient charge extraction and surface traps passivation. The TPP‐SMeTAD‐based PVSCs exhibit both improved photovoltaic performance and reduced hysteresis in p‐i‐n PVSCs over those based on TPP‐OMeTAD. This work not only provides new insights on creating perovskite‐HEM heterojunction but also helps in designing new HEM to enable efficient organic–inorganic hybrid PVSCs.     

Simultaneous Improvement in Efficiency and Stability of Low‐Temperature‐Processed Perovskite Solar Cells by Interfacial Control

In most current state‐of‐the‐art perovskite solar cells (PSCs), high‐temperature (≈500 °C)‐sintered metal oxides are employed as electron‐transporting layers (ETLs). To lower the device processing temperature, the development of low‐temperature‐processable ETL materials (such as solution‐processed ZnO) has received growing attention. However, thus far, the use of solution‐processed ZnO is limited because the reverse decomposition reaction that occurs at ZnO/perovskite interfaces significantly degrades the charge collection and stability of PSCs. In this work, the reverse decomposition reaction is successfully retarded by sulfur passivation of solution‐processed ZnO. The sulfur passivation of ZnO by a simple chemical means, efficiently reduces the oxygen‐deficient defects and surface oxygen‐containing groups, thus effectively preventing reverse decomposition reactions during and after formation of the perovskite active layers. Using the low‐temperature‐processed sulfur‐passivated ZnO (ZnO–S), perovskite layers with higher crystallinity and larger grain size are obtained, while the charge extraction at the ZnO/perovskite interface is significantly improved. As a result, the ZnO–S‐based PSCs achieve substantially improved power‐conversion‐efficiency (PCE) (19.65%) and long‐term air‐storage stability (90% retention after 40 d) compared with pristine ZnO‐based PSCs (16.51% and 1% retention after 40 d). Notably, the PCE achieved is the highest recorded (19.65%) for low‐temperature ZnO‐based PSCs.     

Enhanced Efficiency and Stability of Perovskite Solar Cells Through Nd‐Doping of Mesostructured TiO2

Block‐copolymer templated chemical solution deposition is used to prepare mesoporous Nd‐doped TiO₂ electrodes for perovskite‐based solar cells. X‐ray diffraction and photothermal deflection spectroscopy show substitutional incorporation into the TiO₂ crystal lattice for low Nd concentration, and increasing interstitial doping for higher concentrations. Substitutional Nd‐doping leads to an increase in stability and performance of perovskite solar cells by eliminating defects and thus increasing electron transport and reducing charge recombination in the mesoporous TiO₂. The optimized doping concentration of 0.3% Nd enables the preparation of perovskite solar cells with stabilized power conversion efficiency of >18%.     

Carbon Nanoparticles in High‐Performance Perovskite Solar Cells

In the past few years, organic–inorganic metal halide ABX₃ perovskites (A = Rb, Cs, methylammonium, formamidinium (FA); B = Pb, Sn; X = Cl, Br, I) have rapidly emerged as promising materials for photovoltaic applications. Tuning the film morphology by various deposition techniques and additives is crucial to achieve solar cells with high performance and long‐term stability. In this work, carbon nanoparticles (CNPs) containing functional groups are added to the perovskite precursor solution for fabrication of fluorine‐doped tin oxide/TiO₂/perovskite/spiro‐OMeTAD/gold devices. With the addition of CNPs, the perovskite films are thermally more stable, contain larger grains, and become more hydrophobic. NMR experiments provide strong evidence that the functional groups of the CNPs interact with FA cations already in the precursor solution. The fabricated solar cells show a power‐conversion efficiency of 18% and negligible hysteresis.     

Interface‐Modification‐Induced Gradient Energy Band for Highly Efficient CsPbIBr2 Perovskite Solar Cells

Inorganic cesium lead halide perovskite solar cells (PSCs) have received enormous attention due to their excellent stability compared with that of their organic–inorganic counterparts. However, the lack of optimization strategies leads the inorganic PSCs to suffer from low efficiency arising from significant recombination. To overcome this dilemma, a surface modification of the electron transport layer (ETL)/perovskite interface is undertaken by using SmBr₃ to improve the crystallization and morphology of the perovskite layer for enhanced ETL/perovskite interface interaction. Encouragingly, a gradient energy band is created at the interface with an outstanding hole blocking effect. As a result, both the charge recombination occurring at the interface and the nonradiative recombination inside the perovskite are suppressed, and, simultaneously, the charge extraction is improved successfully. Therefore, the power conversion efficiency of the CsPbIBr₂ PSCs is increased to as high as 10.88% under one sun illumination, which is 30% higher than its counterparts without the modification. It is logically inferred that this valuable optimization strategy can be extended to other analogous structures and materials.     

In Situ Grain Boundary Functionalization for Stable and Efficient Inorganic CsPbI2Br Perovskite Solar Cells

The phase instability and large energy loss are two obstacles to achieve stable and efficient inorganic‐CsPbI_3?xBr_x perovskite solar cells. In this work, stable cubic perovskite (α)‐phase CsPbI₂Br is successfully achieved by Pb(Ac)₂ functioning at the grain boundary under low temperature. Ac^? strongly coordinates with CsPbI₂Br to stabilize the α‐phase and also make the grain size smaller and film uniform by fast nucleation. PbO is formed in situ at the grain boundary by decomposing Pb(Ac)₂ at high‐temperature annealing. The semiconducting PbO effectively passivates the surface states, reduces the interface recombination, and promotes the charge transport in CsPbI₂Br perovskite solar cells. A 12% efficiency and good stability are obtained for in situ PbO‐passivated CsPbI₂Br solar cells, while Pb(Ac)₂‐passivated device exhibits 8.7% performance and the highest stability, much better than the control device with 8.5% performance and inferior stability. This article highlights the extrinsic ionic grain boundary functionalization to achieve stable and efficient inorganic CsPbI_3?xBr_x materials and the devices.     

Improving Perovskite Solar Cells: Insights From a Validated Device Model

To improve the efficiency of existing perovskite solar cells (PSCs), a detailed understanding of the underlying device physics during their operation is essential. Here, a device model has been developed and validated that describes the operation of PSCs and quantitatively explains the role of contacts, the electron and hole transport layers, charge generation, drift and diffusion of charge carriers and recombination. The simulation to the experimental data of vacuum‐deposited CH₃NH₃PbI₃ solar cells over multiple thicknesses has been fit and the device behavior under different operating conditions has been studied to delineate the influence of the external bias, charge‐carrier mobilities, energetic barriers for charge injection/extraction and, different recombination channels on the solar cell performance. By doing so, a unique set of material parameters and physical processes that describe these solar cells is identified. Trap‐assisted recombination at material interfaces is the dominant recombination channel limiting device performance and passivation of traps increases the power conversion efficiency (PCE) of these devices by 40%. Finally, guidelines to increase their performance have been issued and it is shown that a PCE beyond 25% is within reach.     

Efficient Passivation of Hybrid Perovskite Solar Cells Using Organic Dyes with ?COOH Functional Group

Organic–inorganic halide perovskites are efficient absorbers for solar cells. Nevertheless, the trap states at the surfaces and grain boundaries are a detrimental factor compromising the device performance. Here, an organic dye (AQ310) is employed as passivator to reduce the trap states of the perovskites and promote better stability. The results demonstrate that the trap states of perovskite are minimized by the presence of AQ310's ? COOH group and the formation of coordination with under‐coordinated Pb²⁺ ions. The resulting carrier recombination time is prolonged and verified by the photoluminescence and open‐circuit voltage decay measurements. Consequently, the best average power conversion efficiency (PCE) of 19.43% is achieved for the perovskite solar cell (PSC) with AQ310 passivation, as compared with a low average PCE of 17.98% for the PSC without AQ310 passivation.