A High‐Performance D–A Copolymer Based on Dithieno[3,2‐b:2′,3′‐d]Pyridin‐5(4H)‐One Unit Compatible with Fullerene and Nonfullerene Acceptors in Solar Cells

Development of high‐performance donor–acceptor (D–A) copolymers is vital in the research of polymer solar cells (PSCs). In this work, a low‐bandgap D–A copolymer based on dithieno[3,2‐b:2′,3′‐d]pyridin‐5(4H)‐one unit (DTP), PDTP4TFBT, is developed and used as the donor material for PSCs with PC₇₁BM or ITIC as the acceptor. PDTP4TFBT:PC₇₁BM and PDTP4TFBT:ITIC solar cells give power conversion efficiencies (PCEs) up to 8.75% and 7.58%, respectively. 1,8‐Diiodooctane affects film morphology and device performance for fullerene and nonfullerene solar cells. It inhibits the active materials from forming large domains and improves PCE for PDTP4TFBT:PC₇₁BM cells, while it promotes the aggregation and deteriorates performance for PDTP4TFBT:ITIC cells. The ternary‐blend cells based on PDTP4TFBT:PC₇₁BM:ITIC (1:1.2:0.3) give a decent PCE of 9.20%.     

Higher Mobility and Carrier Lifetimes in Solution‐Processable Small‐Molecule Ternary Solar Cells with 11% Efficiency

Solution‐processed small molecule (SM) solar cells have the prospect to outperform their polymer‐fullerene counterparts. Considering that both SM donors/acceptors absorb in visible spectral range, higher expected photocurrents should in principle translate into higher power conversion efficiencies (PCEs). However, limited bulk‐heterojunction (BHJ) charge carrier mobility (<10^‐4 cm² V^‐1 s^‐1) and carrier lifetimes (<1 µs) often impose active layer thickness constraints on BHJ devices (≈100 nm), limiting external quantum efficiencies (EQEs) and photocurrent, and making large‐scale processing techniques particularly challenging. In this report, it is shown that ternary BHJs composed of the SM donor DR3TBDTT (DR3), the SM acceptor ICC6 and the fullerene acceptor PC₇₁BM can be used to achieve SM‐based ternary BHJ solar cells with active layer thicknesses >200 nm and PCEs nearing 11%. The examinations show that these remarkable figures are the result of i) significantly improved electron mobility (8.2 × 10^‐4 cm² V^‐1 s^‐1), ii) longer carrier lifetimes (2.4 µs), and iii) reduced geminate recombination within BHJ active layers to which PC₇₁BM has been added as ternary component. Optically thick (up to ≈500 nm) devices are shown to maintain PCEs >8%, and optimized DR3:ICC6:PC₇₁BM solar cells demonstrate long‐term shelf stability (dark) for >1000 h, in 55% humidity air environment.     

Feasible D1–A–D2–A Random Copolymers for Simultaneous High‐Performance Fullerene and Nonfullerene Solar Cells

A series of PBDB‐TTn random donor copolymers is synthesized, consisting of an electron‐deficient benzo[1,2‐c:4,5‐c′]dithiophene‐4,8‐dione (BDD) unit and different ratios of two electron‐rich benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thieno[3,2‐b]thiophene (TT) units, with intention to modulate the intrachain and/or interchain interactions and ultimately bulk‐heterojunction morphology evolution. A comparative study using 4 × 2 polymer solar cell (PSC) performance maps and each of the [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) and the fused‐aromatic‐ring‐based molecule (m‐ITIC) acceptors are carried out. Given the similarities in their absorption ranges and energy levels, the PBDB‐TTn copolymers clearly reveal a change in the absorption coefficients upon optimization of the BDT to TT ratio in the backbone. Among the given acceptor combination sets, superior performances are observed in the case of PBDB‐TT5 blended with PC₇₁BM (8.34 ± 0.10%) or m‐ITIC (11.10 ± 0.08%), and the dominant factors causing power conversion efficiency differences in them are found to be distinctly different. For example, the performances of PC₇₁BM‐based PSCs are governed by size and population of face‐on crystallites, while intermixed morphology without the formation of large phase‐separated aggregates is the key factor for achieving high‐performance m‐ITIC‐based PSCs. This study presents a new sketch of structure–morphology–performance relationships for fullerene‐ versus nonfullerene‐based PSCs.     

Self‐Organization of Polymer Additive,Poly(2‐vinylpyridine) via One‐Step Solution Processing to Enhance the Efficiency and Stability of Polymer Solar Cells

Interfaces between the photoactive layers and electrodes play critical roles in controlling the performance of optoelectronic devices. Herein, a novel nonconjugated polymer additive (nPA), poly(2‐vinylpyridine) (P2VP), is reported for modifying the interfaces between the bulk‐heterojunction (BHJ) and cathode/metal oxide (MO) layers. The P2VP nPA enables remarkably enhanced power conversion efficiencies (PCEs) and ambient stability in different types of polymer solar cells (PSCs). Importantly, interfacial engineering can be achieved during deposition of the P2VP nPA‐containing BHJ active layer via simple, one‐step solution processing. The P2VP nPA has much higher surface energy than the BHJ active components and stronger interaction with the surface of MO, which affords spontaneous vertical phase separation from the BHJ layer on the MO surface by one‐step solution processing. The self‐assembled P2VP layer substantially reduces the work function and surface defect density of MO, thereby minimizing the charge‐extraction barrier and increasing the PCEs of the PSCs significantly, i.e., PTB7‐Th:PC₇₁BM (10.53%→11.14%), PTB7:PC₇₁BM (7.37%→8.67%), and PTB7‐Th:P(NDI2HD‐T) all‐PSCs (5.52%→6.14%). In addition, the lifetimes of the PSCs are greatly improved by the use of the P2VP nPA.     

Rational Strategy to Stabilize an Unstable High‐Efficiency Binary Nonfullerene Organic Solar Cells with a Third Component

Long device lifetime is still a missing key requirement in the commercialization of nonfullerene acceptor (NFA) organic solar cell technology. Understanding thermodynamic factors driving morphology degradation or stabilization is correspondingly lacking. In this report, thermodynamics is combined with morphology to elucidate the instability of highly efficient PTB7‐Th:IEICO‐4F binary solar cells and to rationally use PC₇₁BM in ternary solar cells to reduce the loss in the power conversion efficiency from ≈35% to <10% after storage for 90 days and at the same time improve performance. The hypomiscibility observed for IEICO‐4F in PTB7‐Th (below the percolation threshold) leads to overpurification of the mixed domains. By contrast, the hypermiscibility of PC₇₁BM in PTB7‐Th of 48 vol% is well above the percolation threshold. At the same time, PC₇₁BM is partly miscible in IEICO‐4F suppressing crystallization of IEICO‐4F. This work systematically illustrates the origin of the intrinsic degradation of PTB7‐Th:IEICO‐4F binary solar cells, demonstrates the structure–function relations among thermodynamics, morphology, and photovoltaic performance, and finally carries out a rational strategy to suppress the degradation: the third component needs to have a miscibility in the donor polymer at or above the percolation threshold, yet also needs to be partly miscible with the crystallizable acceptor.     

Fabricating High Performance,Donor–Acceptor Copolymer Solar Cells by Spray‐Coating in Air

We report the fabrication of high performance organic solar cells by spray‐coating the photoactive layer in air. The photovoltaic blends consist of a blend of carbazole and benzothiadiazole based donor–acceptor copolymers and the fullerene derivative PC₇₀BM. Here, we formulate a number of photovoltaic inks using a range of solvent systems that we show can all be deposited by spray casting. We use a range of techniques to characterize the structure of such films, and show that spray‐cast films have comparable surface roughness to spin‐cast films and that vertical stratification that occurs during film drying reduces the concentration of PCBM towards the underlying PEDOT:PSS interface. We also show that the active layer thickness and the drying kinetics can be tuned through control of the substrate temperature. High power conversion efficiencies of 4.3%, 4.5% and 4.6% were obtained for solar cells made from a blend of PC₇₀BM with the carbazole‐based co‐polymers PCDTBT, P2 and P1. By applying a low temperature anneal after the deposition of the cathode, the efficiency of spray‐cast solar‐cells based on a P2:PC₇₀BM blend is increased to 5.0%. Spray coating holds significant promise as a technique capable of fabricating large‐area, high performance organic solar cells in air.     

Effect of Molecular Orientation of Donor Polymers on Charge Generation and Photovoltaic Properties in Bulk Heterojunction All‐Polymer Solar Cells

All‐polymer solar cells (all‐PSCs) utilizing p‐type polymers as electron‐donors and n ‐typepolymers as electron‐acceptors have attracted a great deal of attention, and their efficiencies have been improved considerably. Here, five polymer donors with different molecular orientations are synthesized by random copolymerization of 5‐fluoro‐2,1,3‐benzothiadiazole with different relative amounts of 2,2′‐bithiophene (2T) and dithieno[3,2‐b;2′,3′‐d]thiophene (DTT). Solar cells are prepared by blending the polymer donors with a naphthalene diimide‐based polymer acceptor (PNDI) or a [6,6]‐phenyl C₇₁‐butyric acid methyl ester (PC₇₁BM) acceptor and their morphologies and crystallinity as well as optoelectronic, charge‐transport and photovoltaic properties are studied. Interestingly, charge generation in the solar cells is found to show higher dependence on the crystal orientation of the donor polymer for the PNDI‐based all‐PSCs than for the conventional PC₇₁BM‐based PSCs. As the population of face‐on‐oriented crystallites of the donor increased in PNDI‐based PSC, the short‐circuit current density (J_SC) and external quantum efficiency of the devices are found to significantly improve. Consequently, device efficiency was enhanced of all‐PSC from 3.11% to 6.01%. The study reveals that producing the same crystal orientation between the polymer donor and acceptor (face‐on/face‐on) is important in all‐PSCs because they provide efficient charge transfer at the donor/acceptor interface.     

Enhanced Photovoltaic Performance of Amorphous Donor–Acceptor Copolymers Based on Fluorine‐Substituted Benzodioxocyclohexene‐Annelated Thiophene

Donor–acceptor (D‐A) type π‐conjugated copolymers with crystalline behavior have been extensively investigated as donor semiconductors in organic photovoltaics (OPVs). On the other hand, the development of high‐performance amorphous donor materials is still behind. The amorphous donor copolymer DTS‐C₀(F₂) consisting of dithieno[3,2‐b:2′,3′‐d]silole ( DTS ) donor unit and the recently developed fluorine‐substituted naphtho[2,3‐c]thiophene‐4,9‐dione ( C₀(F₂) ) acceptor unit shows moderate photovoltaic performance upon blending with PC₇₁BM. In this work, to enhance the hole‐transporting characteristics, a 3‐hexylthiophene ( HT ) spacer unit is integrated into the conjugated backbone, resulting in a new amorphous copolymer DTS‐HT‐C₀(F₂) . The strong electron‐accepting nature of C₀(F₂) allows the introduction of the HT spacer without affecting the frontier orbital energies and thus the D‐A character. Without using solvent additives and thermal annealing, OPVs based on DTS‐HT‐C₀(F₂) and [6,6]‐phenyl‐C71‐butyric acid methyl ester PC₇₁BM show an improved power conversion efficiency of 9.12%. Investigation of the device physics unambiguously reveals that the hole mobility of the copolymer in the blend is increased by an order of magnitude by the introduction of HT , while keeping an amorphous film nature, leading to higher short‐circuit current density and fill factor. These results demonstrate the realization of high‐performance OPVs based on amorphous active layers.     

Layer‐by‐Layer Solution‐Processed Low‐Bandgap Polymer‐PC61BM Solar Cells with High Efficiency

Polymer solar cells (PSCs) are fabricated without solvent additives using a low‐bandgap polymer, PBDTTT‐C‐T, as the donor and [6,6]‐phenyl‐C61‐butyric‐acid‐methyl‐ester (PC₆₁BM) as the acceptor. Donor‐acceptor blend and layer‐by‐layer (LL) solution process are used to form active layers. Relative to the blend devices, the LL devices exhibit stronger absorption, better vertical phase separation, higher hole and electron mobilities, and better charge extraction at correct electrodes. As a result, after thermal annealing the LL devices exhibit an average power conversion efficiency (PCE) of 6.86%, which is much higher than that of the blend devices (4.31%). The best PCE of the LL devices is 7.13%, which is the highest reported for LL processed PSCs and among the highest reported for PC₆₁BM‐based single‐junction PSCs.     

Work Function Control of Interfacial Buffer Layers for Efficient and Air‐Stable Inverted Low‐Bandgap Organic Photovoltaics

A water‐soluble cationic polythiophene derivative, poly[3‐(6‐{4‐tert‐butylpyridiniumyl}‐hexyl)thiophene‐2,5‐diyl] [P3(TBP)HT], is combined with anionic poly(3,4‐ethylenedioxythiophene):poly(p‐styrenesulfonate) (PEDOT:PSS) on indium tin oxide (ITO) substrates via electrostatic layer‐by‐layer (eLbL) assembly. By varying the number of eLbL layers, the electrode's work function is precisely controlled from 4.6 to 3.8 eV. These polymeric coatings are used as cathodic interfacial modifiers for inverted‐mode organic photovoltaics that incorporate a photoactive layer composed of either poly[(3‐hexylthiophene)‐2,5‐diyl] (P3HT) and the fullerene acceptor [6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or the low bandgap polymer [poly({4,8‐di(2‐ethylhexyloxyl)benzo[1,2‐b:4,5‐b′]dithiophene}‐2,6‐diyl)‐alt‐({5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}‐1,3‐diyl) (PBDTTPD)] and the electron acceptor [6,6‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM)]. The power conversion efficiency (PCE) of the resulting photovoltaic device is dependent on the composition of the eLbL‐assembled interface and permits the fabrication of devices with efficiencies of 3.8% and 5.6% for P3HT and PBDTTPD donor polymers, respectively. Notably, these devices demonstrate significant stability with a P3HT:PC₆₁BM system maintaining 83% of its original PCE after 1 year of storage and a PBDTTPD:PC₇₁BM system maintaining 97% of its original PCE after over 1000 h of storage in air, according to the ISOS‐D‐1 shelf protocol.     

Toward High‐Temperature Stability of PTB7‐Based Bulk Heterojunction Solar Cells: Impact of Fullerene Size and Solvent Additive

The use of fullerene as acceptor limits the thermal stability of organic solar cells at high temperatures as their diffusion inside the donor leads to phase separation via Ostwald ripening. Here it is reported that fullerene diffusion is fully suppressed at temperatures up to 140 °C in bulk heterojunctions based on the benzodithiophene‐based polymer (the poly[[4,8‐bis[(2‐ethylhexyl)oxy]‐benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]‐thieno[3,4‐b]thiophenediyl]], (PTB7) in combination with the fullerene derivative [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₀BM). The blend stability is found independently of the presence of diiodooctane (DIO) used to optimize nanostructuration and in contrast to PTB7 blends using the smaller fullerene derivative PC₇₀BM. The unprecedented thermal stability of PTB7:PC₇₀BM layers is addressed to local minima in the mixing enthalpy of the blend forming stable phases that inhibit fullerene diffusion. Importantly, although the nanoscale morphology of DIO processed blends is thermally stable, corresponding devices show strong performance losses under thermal stress. Only by the use of a high temperature annealing step removing residual DIO from the device, remarkably stable high efficiency solar cells with performance losses less than 10% after a continuous annealing at 140 °C over 3 days are obtained. These results pave the way toward high temperature stable polymer solar cells using fullerene acceptors.     

Plasmonic Backscattering Effect in High‐Efficient Organic Photovoltaic Devices

A universal strategy for efficient light trapping through the incorporation of gold nanorods on the electron transport layer (rear) of organic photovoltaic devices is demonstrated. Utilizing the photons that are transmitted through the active layer of a bulk heterojunction photovoltaic device and would otherwise be lost, a significant enhancement in power conversion efficiency (PCE) of poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)]:phenyl‐C₇₁‐butyric acid methyl ester (PCDTBT:PC₇₁BM) and poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b] thiophenediyl]] (PTB7):PC₇₁BM by ≈13% and ≈8%, respectively. PCEs over 8% are reported for devices based on the PTB7:PC₇₁BM blend. A comprehensive optical and electrical characterization of our devices to clarify the influence of gold nanorods on exciton generation, dissociation, charge recombination, and transport inside the thin film devices is performed. By correlating the experimental data with detailed numerical simulations, the near‐field and far‐field scattering effects are separated of gold nanorods (Au NRs), and confidently attribute part of the performance enhancement to the enhanced absorption caused by backscattering. While, a secondary contribution from the Au NRs that partially protrude inside the active layer and exhibit strong near‐fields due to localized surface plasmon resonance effects is also observed but is minor in magnitude. Furthermore, another important contribution to the enhanced performance is electrical in nature and comes from the increased charge collection probability.     

The Crucial Influence of Fullerene Phases on Photogeneration in Organic Bulk Heterojunction Solar Cells

The conjugated polymer, poly(2,5‐bis(3‐hexadecylthiophen‐2‐yl)thieno[3,2‐b]thiophene) (pBTTT‐C₁₆), allows a systematic tuning of the blend morphology by varying the acceptor type and fraction, making it a well‐suited structural model for studying the fundamental processes in organic bulk heterojunction solar cells. To analyze the role of intercalated and pure fullerene domains on charge carrier photogeneration, time delayed collection field (TDCF) measurements and Fourier‐transform photocurrent spectroscopy (FTPS) are performed on pBTTT‐C₁₆:[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) solar cells with various stoichiometries. A weak influence of excess photon energy on photogeneration along with a photogeneration having a weaker field dependence at increasing fullerene loading is found. The findings are assigned to a dissociation via thermalized charge transfer (CT) states supported by an enhanced electron delocalization along spatially extended PC₆₁BM nanophases that form in addition to a bimolecular crystal (BMC) for PC₆₁BM rich blends. The highly efficient transfer of charge carriers from the BMC into the pure domains are studied further by TDCF measurements performed on non‐intercalated pBTTT‐C₁₆:bisPC₆₁BM blends. They reveal a field dependent charge generation similar to the 1:4 PC₆₁BM blend, demonstrating that the presence of pure acceptor phases is the major driving force for an efficient, field independent CT dissociation.     

Ultrafast Charge Generation Pathways in Photovoltaic Blends Based on Novel Star‐Shaped Conjugated Molecules

The quest for new materials is one of the main factors propelling recent advances in organic photovoltaics. Star‐shaped small molecules (SSMs) have been proven promising candidates as perspective donor material due to the increase in numbers of excitation pathways caused by the degeneracy of the lowest unoccupied molecular orbital (LUMO) level. In order to unravel the pathways of the initial photon‐to‐charge conversion, the photovoltaic blends based on three different SSMs with a generic structure of N(phenylene‐nthiophene‐dicyanovinyl‐alkyl)₃ (n = 1–3), and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) acceptor are investigated by ultrafast photoinduced absorption spectroscopy assisted by density functional theory calculations. It is shown that both electron transfer from SSMs to PC₇₁BM and hole transfer from PC₇₁BM to SSMs are equally significant for generation of long‐lived charges. In contrast, intramolecular (intra‐SSM) charge separation results in geminate recombination and therefore constitutes a loss channel. Overall, up to 60% of long‐lived separated charges are generated at the optimal PC₇₁BM concentrations. The obtained results suggest that further improvement of the SSM‐based solar cells is feasible via optimization of blend morphology and by suppressing the intra‐SSM recombination channel.     

π‐Extended Narrow‐Bandgap Diketopyrrolopyrrole‐Based Oligomers for Solution‐Processed Inverted Organic Solar Cells

A series of narrow‐bandgap π‐conjugated oligomers based on diketopyrrolopyrrole chromophoric units coupled with benzodithiophene, indacenodithiophene, thiophene, and isoindigo cores are designed and synthesized for application as donor materials in solution‐processed small‐molecule organic solar cells. The impacts of these different central cores on the optoelectronic and morphological properties, carrier mobility, and photovoltaic performance are investigated. These π‐extended oligomers possess broad and intense optical absorption covering the range from 550 to 750 nm, narrow optical bandgaps of 1.52–1.69 eV, and relatively low‐lying highest occupied molecular orbital (HOMO) energy levels ranging from ?5.24 to ?5.46 eV in their thin films. A high power conversion efficiency of 5.9% under simulated AM 1.5G illumination is achieved for inverted organic solar cells based on a small‐molecule bulk‐heterojunction system consisting of a benzodithiophene‐diketopyrrolopyrrole‐containing oligomer as a donor and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as an acceptor. Transmission electron microscopy and energy‐dispersive X‐ray spectroscopy reveal that interpenetrating and interconnected donor/acceptor domains with pronounced mesoscopic phase segregation are formed within the photoactive binary blends, which is ideal for efficient exciton dissociation and charge transport in the bulk‐heterojunction devices.     

High‐Performance Wide Bandgap Copolymers Using an EDOT Modified Benzodithiophene Donor Block with 10.11% Efficiency

Newly developed benzo[1,2‐b:4,5‐b′]dithiophene (BDT) block with 3,4‐ethylenedioxythiophene (EDOT) side chains is first employed to build efficient photovoltaic copolymers. The resulting copolymers, PBDTEDOT‐BT and PBDTEDOTFBT, have a large bandgap more than 1.80 eV, which is attributed to the increased steric hindrance between the BDT and EDOT skeletons. Both copolymers possess the satisfied absorptions, low‐lying highest occupied molecular orbital (HOMO) levels and high crystallinity. Using the fluorination strategy, PBDTEDOT‐FBT exhibits a wider and stronger absorption and a deeper HOMO level than those of PBDTEDOT‐BT. PBDTEDOT‐FBT:[6,6]‐Phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) blend also shows the higher hole mobility and better surface morphology compared with the PBDTEDOTBT:PC₇₁BM blend. Combination of above advantages, PBDTEDOT‐FBT devices exhibit much higher power conversion efficiency (PCE) of 10.11%, with an improved open circuit voltage (V_oc) of 0.86 V, short circuit current densities (J_sc) of 16.01 mA cm^?2, and fill factor (FF) of 72.6%. This work not only provides a newly efficient candidate of BDT donor block modified with EDOT conjugated side chains, but also achieves high‐performance large bandgap copolymers for polymer solar cells (PSCs) via the synergistic effect of fluorination and side chain engineering strategies.     

Efficient Semi‐Transparent Organic Solar Cells with Good Transparency Color Perception and Rendering Properties

Window integrated photovoltaics for automotive and building applications are a promising market segment for organic solar modules. Besides semi‐transparency, window integrated applications require a reasonable transparency perception and good color rendering properties in order to be suitable for realistic scene illumination. Here, the transmitted light through semi‐transparent organic solar cells comprising the polymer/fullerene blend poly[(4,4'‐bis(2‐ethylhexyl)dithieno[3,2‐b:2',3'‐d]silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl]: [6,6]‐phenyl C₇₁‐butric acid methyl ester (PSBTBT:PC₇₀BM) as active layer and a sputtered aluminum doped zinc oxide cathode were found to exhibit a color neutral perception for the human eye and very good color rendering properties. Moreover, the electrical cell properties allow for efficient energy harvesting with an overall power conversion efficiency η ≈ 3%.     

Benzo[1,2‐b:4,5‐b′]Dithiophene–6,7‐Difluoroquinoxaline Small Molecule Donors with >8% BHJ Solar Cell Efficiency

Solution‐processable small molecule (SM) donors are promising alternatives to their polymer counterparts in bulk‐heterojunction (BHJ) solar cells. While SM donors with favorable spectral absorption, self‐assembly patterns, optimum thin‐film morphologies, and high carrier mobilities in optimized donor–acceptor blends are required to further BHJ device efficiencies, material structure governs each one of those attributes. As a result, the rational design of SM donors with gradually improved BHJ solar cell efficiencies must concurrently address: (i) bandgap tuning and optimization of spectral absorption (inherent to the SM main chain) and (ii) pendant‐group substitution promoting structural order and mediating morphological effects. In this paper, the rational pendant‐group substitution in benzo[1,2‐b:4,5‐b′]dithiophene–6,7‐difluoroquinoxaline SMs is shown to be an effective approach to narrowing the optical gap (E_opt) of the SM donors ( SM1 and SM2 ), without altering their propensity to order and form favorable thin‐film BHJ morphologies with PC₇₁BM. Systematic device examinations show that power conversion efficiencies >8% and open‐circuit voltages (V_OC) nearing 1 V can be achieved with the narrow‐gap SM donor analog ( SM2 , E_opt = 1.6 eV) and that charge transport in optimized BHJ solar cells proceeds with minimal, nearly trap‐free recombination. Detailed device simulations, light intensity dependence, and transient photocurrent analyses emphasize how carrier recombination impacts BHJ device performance upon optimization of active layer thickness and morphology.     

Impact of Fullerene Molecular Weight on P3HT:PCBM Microstructure Studied Using Organic Thin‐Film Transistors

The clustering and diffusion of C₇₁‐butyric acid methyl ester (PC₇₁BM) in poly(3‐hexylthiophene) (P3HT) has been studied using single layer blend and bilayer organic field‐effect transistors (OFETs) and by atomic force microscopy (AFM). P3HT:PC₇₁BM blend based OFETs were found to undergo phase‐segregation upon annealing, which was detectable as a fall in electron mobility with increasing annealing temperature. By employing carefully designed bilayer P3HT:PC₇₁BM OFETs, the diffusion‐properties of PC₇₁BM in P3HT could additionally be inferred from electron mobility measurements. It was found that the prerequisite annealing temperatures for detectable PC₇₁BM clustering and diffusion in P3HT was approximately 20 °C higher than for PC₆₁BM. The diffusion coefficient of PC₆₁BM in P3HT was found to be several times higher that that of PC₇₁BM. The present work provides unique insights into the diffusion process of fullerenes in conjugated polymers and could prove highly valuable for future materials development and device optimization.     

Interface Design to Improve the Performance and Stability of Solution‐Processed Small‐Molecule Conventional Solar Cells

A systematic study on the effect of various cathode buffer layers on the performance and stability of solution‐processed small‐molecule organic solar cells (SMOSCs) based on tris{4‐[5‐(1,1‐dicyanobut‐1‐en‐2‐yl)‐2,2‐bithiophen‐5‐yl]phenyl}amine (N(Ph‐2T‐DCN‐Et)₃):6,6‐phenyl‐C71‐butyric acid methyl ester (N(Ph‐2T‐DCN‐Et)₃:PC₇₀BM) is presented. The power conversion efficiency (PCE) in these systems can be significantly improved from approximately 4% to 5.16% by inserting a metal oxide (ZnO) layer between the active layer and the Al cathode instead of an air‐sensitive Ba or Ca layer. However, the low work‐function Al cathode is susceptible to chemical oxidation in the atmosphere. Here, an amine group functionalized fullerene complex (DMAPA‐C₆₀) is inserted as a cathode buffer layer to successfully modify the interface towards ZnO/Ag and active layer/Ag functionality. For devices with ZnO/DMAPA‐C₆₀/Ag and DMAPA‐C₆₀/Ag cathodes the PCEs are improved from 2.75% to 4.31% and to 5.40%, respectively, compared to a ZnO/Ag device. Recombination mechanisms and stability aspects of devices with various cathodes are also investigated. The significant improvement in device performance and stability and the simplicity of fabrication by solution processing suggest this DMAPA‐C₆₀‐based interface as a promising and practical pathway for developing efficient, stable, and roll‐to‐roll processable SMOSCs.