p‐Type CuI Islands on TiO2 Electron Transport Layer for a Highly Efficient Planar‐Perovskite Solar Cell with Negligible Hysteresis

Compact TiO₂ is widely used as an electron transport material in planar‐perovskite solar cells. However, TiO₂‐based planar‐perovskite solar cells exhibit low efficiencies due to intrinsic problems such as the unsuitable conduction band energy and low electron extraction ability of TiO₂. Herein, the planar TiO₂ electron transport layer (ETL) of perovskite solar cells is modified with ionic salt CuI via a simple one‐step spin‐coating process. The p‐type nature of the CuI islands on the TiO₂ surface leads to modification of the TiO₂ band alignment, resulting in barrier‐free contacts and increased open‐circuit voltage. It is found that the polarity of the CuI‐modified TiO₂ surface can pull electrons to the interface between the perovskite and the TiO₂, which improves electron extraction and reduces nonradiative recombination. The CuI solution concentration is varied to control the electron extraction of the modified TiO₂ ETL, and the optimized device shows a high efficiency of 19.0%. In addition, the optimized device shows negligible hysteresis, which is believed to be due to the removal of trap sites and effective electron extraction by CuI‐modified TiO₂. These results demonstrate the hitherto unknown effect of p‐type ionic salts on electron transport material.     

Overcoming the “Light‐Soaking” Issue in Inverted Organic Solar Cells by the Use of Al:ZnO Electron Extraction Layers

A common phenomenon of organic solar cells (OSCs) incorporating metal‐oxide electron extraction layers is the requirement to expose the devices to UV light in order to improve device characteristics – known as the so‐called “light‐soaking” issue. This behaviour appears to be of general validity for various metal‐oxide layers, various organic donor/acceptor systems, and regardless if single junction devices or multi stacked cells are considered. The requirement of UV exposure of OSCs may impose severe problems if substrates with limited UV transmission, UV blocking filters or UV to VIS down‐conversion concepts are applied. In this paper, we will demonstrate that this issue can be overcome by the use of Al doped ZnO (AZO) as electron extraction interlayer. In contrast to devices based on TiO_x and ZnO, the AZO devices show well‐behaved solar cell characteristics with a high fill factor (FF) and power conversion efficiency (PCE) even without the UV spectral components of the AM1.5 solar spectrum. As opposed to previous claims, our results indicate that the origin of s‐shaped characteristics of the OSCs is the metal‐oxide/organic interface. The electronic structures of the TiO_x/fullerene and AZO/fullerene interfaces are studied by photoelectron spectroscopy, revealing an electron extraction barrier for the TiO_x/fullerene case and facilitated electron extraction for AZO/fullerene. These results are of general relevance for organic solar cells based on various donor acceptor active systems.     

Atomic‐Layer‐Deposited Aluminum and Zirconium Oxides for Surface Passivation of TiO2 in High‐Efficiency Organic Photovoltaics

The reduction in electronic recombination losses by the passivation of surfaces is a key factor enabling high‐efficiency solar cells. Here a strategy to passivate surface trap states of TiO₂ films used as cathode interlayers in organic photovoltaics (OPVs) through applying alumina (Al₂O₃) or zirconia (ZrO₂) insulating nanolayers by thermal atomic layer deposition (ALD) is investigated. The results suggest that the surface traps in TiO₂ are oxygen vacancies, which cause undesirable recombination and high electron extraction barrier, reducing the open‐circuit voltage and the short‐circuit current of the complete OPV device. It is found that the ALD metal oxides enable excellent passivation of the TiO₂ surface followed by a downward shift of the conduction band minimum. OPV devices based on different photoactive layers and using the passivated TiO₂ electron extraction layers exhibit a significant enhancement of more than 30% in their power conversion efficiencies compared to their reference devices without the insulating metal oxide nanolayers. This is a result of significant suppression of charge recombination and enhanced electron extraction rates at the TiO₂/ALD metal oxide/organic interface.     

Hybrid Dye‐Titania Nanoparticles for Superior Low‐Temperature Dye‐Sensitized Solar Cells

In this work, a new strategy to design low‐temperature (≤200 °C) sintered dye‐sensitized solar cells (lt‐DSSC) is reported to enhance charge collection efficiencies (η_coll), photoconversion efficiencies (η), and stabilities under continuous operation conditions. Realization of lt‐DSSC is enabled by the integration of hybrid nanoparticles based on TiO₂‐Ru(II) complex (TiO₂_Ru_IS)—obtained by in situ bottom‐up construction of Ru(II) N3 dye‐sensitized titania—into the photoelectrode. Incentives for the use of TiO₂_Ru_IS are i) dye stability due to its integration into the TiO₂ anatase network and ii) enhanced charge collection yield due to its significant resistance toward electron recombination with electrolytes. It is demonstrated that devices with single‐layer photoelectrodes featuring blends of P25 and TiO₂_Ru_IS give rise to a 60% η_coll relative to a 46% η_coll for devices with P25‐based photoelectrodes. Responsible for this trend is a better charge transport and a reduced electron recombination. When using a multilayered photoelectrode architecture with a top layer based only on TiO₂_Ru_IS, devices with an even higher η_coll (74%) featuring a η of around 8.75% and stabilities of 600 h are achieved. This represents the highest values reported for lt‐DSSC to date.     

Interfacing Pristine C60 onto TiO2 for Viable Flexibility in Perovskite Solar Cells by a Low‐Temperature All‐Solution Process

A low‐temperature solution‐processed strategy is critical for cost‐effective manufacture of flexible perovskite solar cells (PSCs). Based on an aqueous‐processed TiO₂ layer, and conventional fullerene derivatives replaced by a pristine fullerene interlayer of C₆₀, herein a facile interface engineering for making all‐solution‐processed TiO₂/C₆₀ layers in flexible n‐i‐p PSCs is reported. Due to the improvement of the perovskite grain quality, promotion of interfacial charge transfer and suppression of interfacial charge recombination, the stabilized power conversion efficiency for the flexible PSCs reaches as high as 16% with high bending resistance retention (≈80% after 1500 cycles) and high light‐soaking retention (≈100% after 100 min). In addition, the stabilized efficiency is over 19% for the rigid TiO₂/C₆₀‐based PSCs. The present work with the facile low‐temperature solution process renders the practicability for high‐performance flexible PSCs applied to wearable devices, portable equipment, and electric vehicles.     

Stability of Nonfullerene Organic Solar Cells: from Built‐in Potential and Interfacial Passivation Perspectives

Remarkable progress has been made in the development of high‐efficiency solution‐processable nonfullerene organic solar cells (OSCs). However, the effect of the vertical stratification of bulk heterojunction (BHJ) on the efficiency and stability of nonfullerene OSCs is not fully understood yet. In this work, we report our effort to understand the stability of nonfullerene OSCs, made with the binary blend poly[(2,6‐(4, 8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene))‐alt‐(5,5‐(1′,3′‐di‐2‐thienyl‐5′,7′‐bis(2‐ethylhexyl)benzo[1′,2′‐c:4′,5′‐c′] dithiophene‐4,8‐dione)] (PBDB‐T):3,9‐ bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐ dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′] dithiophene (ITIC) system. It shows that a continuous vertical phase separation process occurs, forming a PBDB‐T‐rich top surface and an ITIC‐rich bottom surface in PBDB‐T:ITIC BHJ during the aging period. A gradual decrease in the built‐in potential (V₀) in the regular configuration PBDB‐T:ITIC OSCs, due to the interfacial reaction between the poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate) (PEDOT:PSS) hole transporting layer and ITIC acceptor, is one of the reasons responsible for the performance deterioration. The reduction in V₀, caused by an inevitable reaction at the ITIC/PEDOT:PSS interface in the OSCs, can be suppressed by introducing a MoO₃ interfacial passivation layer. Retaining a stable and high V₀ across the BHJ through interfacial modification and device engineering, e.g., as seen in the inverted PBDB‐T:ITIC OSCs, is a prerequisite for efficient and stable operation of nonfullerene OSCs.     

Nanowire‐Based Three‐Dimensional Transparent Conducting Oxide Electrodes for Extremely Fast Charge Collection

A 3D transparent conducting oxide (3D‐TCO) has been fabricated by growing Sn‐doped indium oxide (ITO) nanowire arrays on glass substrates via a vapor transport method. The 3D TCO charge‐collection properties have been compared to those of conventional two‐dimensional TCO (2D‐TCO) thin films. For use as a photoelectrode in dye‐sensitized solar cells, ITO‐TiO₂ core‐shell nanowire arrays were prepared by depositing a 45 nm‐thick mesoporous TiO₂ shell layer consisting of ～6 nm anatase nanoparticles using TiCl₄ treatments. Dye‐sensitized solar cells fabricated using these ITO‐TiO₂ core‐shell nanowire arrays show extremely fast charge collection owing to the shorter electron paths across the 45 nm‐thick TiO₂ shell compared to the 2D TCO. Interestingly, the charge‐collection time does not increase with the overall electrode thickness, which is counterintuitive to conventional diffusion models. This result implies that, in principle, maximum light harvesting can be achieved without hindering the charge collection. The proposed new 3D TCO should also be attractive for other photovoltaic applications where the active layer thickness is limited by poor charge collection.     

Overcoming Space‐Charge Effect for Efficient Thick‐Film Non‐Fullerene Organic Solar Cells

Organic solar cells (OSCs) containing non‐fullerene acceptors have realized high power conversion efficiency (PCE) up to 14%. However, most of these high‐performance non‐fullerene OSCs have been reported with optimal active layer thickness of about 100 nm, mainly due to the low electron mobility (≈10^?4–10^?5 cm² V^?1 s^?1) of non‐fullerene acceptors, which are not suitable for roll‐to‐roll large‐scale processing. In this work, an efficient non‐fullerene OSC based on poly[(5,6‐difluoro‐2,1,3‐benzothiadiazol‐4,7‐diyl)‐alt‐(3,3′″‐di(2‐octyldodecyl)‐2,2′;5′,2″;5″,2′″‐quaterthiophen‐5,5′′′‐diyl)] (PffBT4T‐2OD):EH‐IDTBR (consists of electron‐rich indaceno[1,2‐b:5,6‐b′]dithiophene as the central unit and an electron‐deficient 5,6‐benzo[c][1,2,5]thiadiazole unit flanked with rhodanine as the peripheral group) with thickness‐independent PCE (maintaining a PCE of 9.1% with an active layer thickness of 300 nm) is presented by optimizing device architectures to overcome the space‐charge effects. Optical modeling reveals that most of the incident light is absorbed near the transparent electrode side in thick‐film devices. The transport distance of electrons with lower mobility will therefore be shortened when using inverted device architecture, in which most of the excitons are generated close to the cathode side and therefore substantially reduces the accumulation of electrons in the device. As a result, an efficient thick‐film non‐fullerene OSC is realized. These results provide important guidelines for the development of more efficient thick‐film non‐fullerene OSCs.     

Triple‐Layer Structured Composite Separator Membranes with Dual Pore Structures and Improved Interfacial Contact for Sustainable Dye‐Sensitized Solar Cells

A composite separator membrane (CSM) with an A/B/A type layered structure, composed of a microporous electrolyte‐philic poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF‐HFP) gel layer (A) and a submicrometer porous polyethylene (PE) or a macroporous poly(ethylene terephthalate) (PET) non‐woven matrix (B), is introduced in a dye‐sensitized solar cell (DSSC). Commercially available PE and PET separator membranes (SMs) act as matrices that provide mechanical stability to the DSSC and permanent pore structures for facilitated ion transport. PVdF‐HFP is used as a microporous gelator for improved interfacial contact between the solid SM and the electrodes. The PVdF‐HFP gel impedes the charge recombination process between electron and I₃ ^? at the TiO₂/electrolyte interface, resulting in improved electron lifetimes. The DSSC assembled with the CSM exhibits high initial solar energy conversion efficiency (η, 6.1%) and stable η values over 1400 h, demonstrating good long term stability. The behaviors of the DSSC are attributed to the synergistic factors of the CSM, such as improved ion conductivity, electrolyte affinity, electrolyte retention capability, effective interfacial contact, and plausible passivation of the dyes. This study demonstrates a practical combination of short‐ and long‐term DSSC performance through the introduction of the CSM.     

Outstanding Performance of Hole‐Blocking Layer‐Free Perovskite Solar Cell Using Hierarchically Porous Fluorine‐Doped Tin Oxide Substrate

Perovskite solar cells (PSCs) are of great interest in current photovoltaic research due to their extraordinary power conversion efficiency of ≈20% and boundless potentialities. The high efficiency has been mostly obtained from TiO₂‐based PSCs, where TiO₂ is utilized as a hole‐blocking, mesoporous layer. However, trapped charges and the light‐induced photocatalytic effect of TiO₂ seriously degrade the perovskite and preclude PSCs from being immediately commercialized. Herein, a simplified PSC is successfully fabricated by eliminating the problematic TiO₂ layers, using instead a fluorine‐doped tin oxide (FTO)/perovskite/hole–conductor/Au design. Simultaneously, the sluggish charge extraction at the FTO/perovskite interface is overcome by modifying the surface of the FTO to a porous structure using electrochemical etching. This surface engineering enables a substantial increase in the photocurrent density and mitigation of the hysteretic behavior of the pristine FTO‐based PSC; a remarkable 19.22% efficiency with a low level of hysteresis is obtained. This performance is closely approaching that of conventional PSCs and may facilitate their commercialization due to improved convenience, lower cost, greater stability, and potentially more efficient mass production.     

Long‐Lived,Visible‐Light‐Excited Charge Carriers of TiO2/BiVO4 Nanocomposites and their Unexpected Photoactivity for Water Splitting

Different mole ratios of TiO₂/BiVO₄ nanocomposites with effective contacts have are fabricated by putting BiVO₄ nanoparticles into the TiO₂ sol, followed by thermal treatment at 450 °C. Based on the transient‐state surface photovoltage responses and the atmosphere‐controlled steady‐state surface photovoltage spectra, it is concluded that the photogenerated charge carriers in the TiO₂/BiVO₄ nanocomposite with a proper mole ratio (5%) display much longer lifetime and higher separation than those in the BiVO₄ alone. This is responsible for the unexpected activity for photoelectrochemical oxidation of water, for photocatalytic production of H₂, and for photocatalytic degradation of phenol as a model pollutant under visible irradiation. Moreover, it is suggested that the prolonged lifetime and increased separation of photogenerated charges in the fabricated TiO₂/BiVO₄ nanocomposite is attributed to the unusual spatial transfer of visible‐excited high‐energy electrons of BiVO₄ to TiO₂. This work will provide feasible routes to synthesize visible‐light responsive nanomaterials for efficient solar utilization.     

Origin of the S‐Shaped JV Curve and the Light‐Soaking Issue in Inverted Organic Solar Cells

Inverted organic solar cells generally exhibit a strong s‐shaped kink in the current–voltage characteristics (JV curve) that may be removed by exposure to UV light (light‐soaking) leading to a drastically improved performance. Using in‐device characterization methods the origin of the light‐soaking issue in inverted solar cells employing titanium dioxide (TiO₂) as an electron selective layer is clarified. An injected hole reservoir accumulated at the TiO₂/organic interface of the pristine device is observed from extraction current transients; the hole reservoir increases the recombination and results in an s‐shape in the JV curve of pristine devices. The hole reservoir and the s‐shape is a result of the energetics at the selective contact in the pristine device; the effect of UV exposure is to decrease the work function of the indium tin oxide/TiO₂‐contact, increasing the built‐in potential. This hinders the build‐up of the hole reservoir and the s‐shape is removed. The proposed model is in excellent agreement with drift‐diffusion simulations.     

UV‐Inert ZnTiO3 Electron Selective Layer for Photostable Perovskite Solar Cells

Although planar‐structured perovskite solar cells (PSCs) have power conversion efficiencies exceeding 24%, the poor photostability, especially with ultraviolet irradiance (UV) severely limits commercial application. The most commonly‐used TiO₂ electron selective layer has a strong photocatalytic effect on perovskite/TiO₂ interface when TiO₂ is excited by UV light. Here a UV‐inert ZnTiO₃ is reported as the electron selective layer in planar PSCs. ZnTiO₃ is a perovskite‐structured semiconductor with excellent chemical stability and poor photocatalysis. Solar cells are fabricated with a structure of indium doped tin oxide (ITO)/ZnTiO₃/Cs_0.05FA_0.81MA_0.14PbI_2.55Br_0.45/Sprio‐MeOTAD/Au. The champion device exhibits a stabilized power conversion efficiency of 19.8% with improved photostability. The device holds 90% of its initial efficiency after 100 h of UV soaking (365 nm, 8 mW cm^?2), compared with 55% for TiO₂‐based devices. This work provides a new class of electron selective materials with excellent UV stability in perovskite solar cell applications.     

Surface Engineering of TiO2 ETL for Highly Efficient and Hysteresis‐Less Planar Perovskite Solar Cell (21.4%) with Enhanced Open‐Circuit Voltage and Stability

Interfacial studies and band alignment engineering on the electron transport layer (ETL) play a key role for fabrication of high‐performance perovskite solar cells (PSCs). Here, an amorphous layer of SnO₂ (a‐SnO₂) between the TiO₂ ETL and the perovskite absorber is inserted and the charge transport properties of the device are studied. The double‐layer structure of TiO₂ compact layer (c‐TiO₂) and a‐SnO₂ ETL leads to modification of interface energetics, resulting in improved charge collection and decreased carrier recombination in PSCs. The optimized device based on a‐SnO₂/c‐TiO₂ ETL shows a maximum power conversion efficiency (PCE) of 21.4% as compared to 19.33% for c‐TiO₂ based device. Moreover, the modified device demonstrates a maximum open‐circuit voltage (V_oc) of 1.223 V with 387 mV loss in potential, which is among the highest reported value for PSCs with negligible hysteresis. The stability results show that the device on c‐TiO₂/a‐SnO₂ retains about 91% of its initial PCE value after 500 h light illumination, which is higher than pure c‐TiO₂ (67%) based devices. Interestingly, using a‐SnO₂/c‐TiO₂ ETL the PCE loss was only 10% of initial value under continuous UV light illumination after 30 h, which is higher than that of c‐TiO₂ based device (28% PCE loss).     

Tunable Nanoporous Network Polymer Nanocomposites having Size‐Selective Ion Transfer for Dye‐Sensitized Solar Cells

Nanoporous network polymer nanocomposites with tunable pore size for size‐dependent selective ion transport are successfully prepared via the surface‐induced cross‐linking polymerization of methyl methacrylate (MMA) and 1,6‐hexanediol diacrylate (HDDA) on the surfaces of nanocrystalline TiO₂ particles. The morphologies of the porous network polymer layer and nanopores were investigated by transmission electron microscopy (TEM), field emission scanning electron microscopy (FE‐SEM), and Brunauer–Emmett–Teller (BET) experiments. The porous layer size‐selectively screened the ions that contacted the nanocrystalline TiO₂ particles, as demonstrated by ion conductivity measurements, electrochemical impedance spectroscopy (EIS), and transient absorption spectroscopy (TAS).     

Contact Doping with Sub‐Monolayers of Strong Polyelectrolytes for Organic Photovoltaics

Barriers to charge transfer at electrode‐semiconductor contacts are ubiquitous and limit the applicability of organic semiconductors in electronic devices. Molecular or ionic doping near contacts can alleviate charge injection or extraction problems by enabling charge tunneling through contact barriers, but the soft nature of organic materials allows for small molecule dopants to diffuse and migrate, degrading the performance of the device and limiting effective interfacial doping. Here, it is demonstrated that contact doping in organic electronics is possible through ionic polymer dopants, which resist diffusion or migration due to their large size. Sub‐monolayer deposition of non‐conjugated strong polyelectrolytes, e.g., sulfonated poly(sulfone)s, at the anode‐semiconductor interface of organic photovoltaics enables efficient hole extraction at the anode. The performance of contact‐doped organic photo­voltaics nearly matches the performance of devices composed of traditional hole transport layers such as poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). The degree of sulfonation of the dopant polymer and the thickness of the ionic dopant layer is shown to be critical for optimizing doping and the efficiency of the device.     

Solvent‐Mediated Dimension Tuning of Semiconducting Oxide Nanostructures as Efficient Charge Extraction Thin Films for Perovskite Solar Cells with Efficiency Exceeding 16%

The recent surge in efficiency and progress of organohalide perovskite solar cells (PSCs) has been significant. The PSC performance is significantly influenced by nanostructuring as this varies the intrinsic optical, electrical, and electrochemical properties. Diverse TiO₂ electron transport layers (ETLs) are solvothermally grown on the transparent conducting oxide substrate with different dimensionalities, 0D nanoparticles (TNP), 1D nanowires (TNW) to 2D nanosheets (TNS), by varying the organic solvent used. These layers feature enhanced optical transparency (≈2%–5% transmittance improvement compared to pristine fluorine doped tin oxide, FTO, glass) minimizing light absorption losses. PSCs constructed using 1D TNW or 2D TNS yield enhanced photovoltaic performance compared to the 0D TNP counterparts. This is a result of i) improved infiltration of the perovskite in the porous TNW or TNS network and ii) facilitated electron transport and charge extraction at the TNW/perovskite or TNS/perovskite interfaces, thus reduced interfacial recombination loss. Employing a bilayered ETL film consisting of a self‐assembled TiO₂ blocking layer and a subsequent TNW active layer, produces PSC devices with an efficiency exceeding 16%. This bilayered ETL film can simultaneously block the photogenerated holes and enhance electron ­extraction, therefore improving PSC performance.     

Bandgap Narrowing in Non‐Fullerene Acceptors: Single Atom Substitution Leads to High Optoelectronic Response Beyond 1000 nm

Two narrow bandgap non‐fullerene acceptors (NBG‐NFAs), namely, COTIC‐4F and SiOTIC‐4F, are designed and synthesized for the fabrication of efficient near‐infrared organic solar cells (OSCs). The chemical structures of the NBG‐NFAs contain a D′‐D‐D′ electron‐rich internal core based on a cyclopentadithiophene (or dithienosilole) (D) and alkoxythienyl (D′) core, end‐capped with the highly electron‐deficient unit 2‐(5,6‐difluoro‐3‐oxo‐2,3‐dihydro‐1H‐inden‐1‐ylidene)malononitrile (A), ultimately providing a A‐D′‐D‐D′‐A molecular configuration that enhances the intramolecular charge transfer characteristics of the excited states. One can thereby reduce the optical bandgap (E_g^opt) to as low as ≈1.10 eV, one of the smallest values for NFAs reported to date. In bulk‐heterojunction (BHJ) OSCs, NBG‐NFA blends with the polymer donor PTB7‐Th yield power conversion efficiencies (PCE) of up to 9.0%, which is particularly high when compared against a range of NBG BHJ blends. Most significantly, it is found that, despite the small energy loss (E_g^opt ? eV_OC) of 0.52 eV, the PTB7‐Th/NBG‐NFA bulk heterojunction blends can yield short‐circuit current densities of up to 22.8 mA cm^?2, suggesting that the design and application of NBG‐NFA materials have substantial potential to further improve the PCE of OSCs.     

New Insights into Defect‐Mediated Heterostructures for Photoelectrochemical Water Splitting

Understanding the interfacial electronic structures of heterojunctions, a challenging undertaking, is extremely important to the design of photoelectrodes for efficient water splitting. The heterostructured interfaces in terms of crystal defects at the atomic‐level exemplified by TiO₂/BiVO₄ are studied. Results from both experimental observations and theoretical calculations clearly confirm the spontaneous formation of defective interfaces in the heterostructures. TiO₂/BiVO₄ junction with engineered interfacial defects can efficiently increase the carrier density and extend the lifetime of electrons. The inherent phenomenon of defective electronic structures in different heterostructures creates a significant impact on their photoelectrochemical performance. The synergetic effect between defect‐mediated mechanism and organic quantum dots sensitization yields significantly increased photoconversion efficiency, which is even superior to that of common metal sulfide sensitized ones. This result demonstrates an approach worthy for the design and fabrication of defect‐mediated heterostructures for water splitting, without utilizing harmful metal sulfides. Moreover, new insights into the influence of intrinsic defects on the interfacial charge transfer process between two different semiconductors for energy‐related applications have also been provided.     

Towards Long‐Term Photostability of Solid‐State Dye Sensitized Solar Cells

The solid‐state dye‐sensitized solar cell (DSSC) was introduced to overcome inherent manufacturing and instability issues of the electrolyte‐based DSSC and progress has been made to deliver high photovoltaic efficiencies at low cost. However, despite 15 years research and development, there still remains no clear demonstration of long‐term stability. Here, solid‐state DSSCs are subjected to the severe aging conditions of continuous illumination at an elevated temperature. A fast deterioration in performance is observed for devices encapsulated in the absence of oxygen. The photovoltaic performance recovers when re‐exposed to air. This reversible behavior is attributed to three related processes: i) the creation of light and oxygen sensitive electronic shunting paths between TiO₂ and the top metal electrode, ii) increased recombination at the TiO₂/organic interface, and iii) the creation of deep electron traps that reduce the photocurrent. The device deterioration is remedied by the formation of an insulating alumino‐silicate shell around the TiO₂ nanocrystals, which reduces interfacial recombination, and the introduction of an insulating mesoporous SiO₂ buffer layer between the top electrode and TiO₂, which acts as a permanent insulating barrier between the TiO₂ and the metal electrode, preventing shunting.