Graphitic Carbon Nitride Induced Micro‐Electric Field for Dendrite‐Free Lithium Metal Anodes

Uncontrolled dendrites resulting from nonuniform lithium (Li) nucleation/growth and Li volume expansion during charging cause serious safety problems for Li anode‐based batteries. Here the coating of nickel foam with graphitic carbon nitride (g‐C₃N₄) to have a 3D current collector (g‐C₃N₄@Ni foam) for dendrite‐free Li metal anodes is reported. The lithiophilic g‐C₃N₄ coupled with the 3D framework is demonstrated to be highly effective for promoting the uniform deposition of Li and suppressing the formation of dendrites. Both density functional theory calculations and experimental studies indicate the formation of a micro‐electric field resulting from the tri‐s‐triazine units of g‐C₃N₄, which induces numerous Li nuclei during the initial nucleation stage, effectively guiding the following Li growth on the 3D Ni foam to be well distributed. Furthermore, the 3D porous framework is favorable for absorbing any volume change and stabilizing the solid–electrolyte interphase layer during repeated Li plating/stripping. As such, a Li metal anode based on the g‐C₃N₄@Ni foam has a remarkable electrochemical performance with a high Coulombic efficiency (98% retention after 300 cycles), an ultralong lifespan up to 900 h, as well as a low overpotential (<15 mV at 1.0 mA cm^?2) at a Li deposition of 9.0 mA h cm^?2.     

High Efficiency Photocatalytic Water Splitting Using 2D α‐Fe2O3/g‐C3N4 Z‐Scheme Catalysts

Photocatalysis is the most promising method for achieving artificial photosynthesis, but a bottleneck is encountered in finding materials that could efficiently promote the water splitting reaction. The nontoxicity, low cost, and versatility of photocatalysts make them especially attractive for this application. This study demonstrates that small amounts of α‐Fe₂O₃ nanosheets can actively promote exfoliation of g‐C₃N₄, producing 2D hybrid that exhibits tight interfaces and an all‐solid‐state Z‐scheme junction. These nanostructured hybrids present a high H₂ evolution rate >3 × 10⁴ µmol g^‐1 h^‐1 and external quantum efficiency of 44.35% at λ = 420 nm, the highest value so far reported among the family of g‐C₃N₄ photocatalysts. Besides effectively suppressing the recombination of electron–hole pairs, this Z‐scheme junction also exhibits activity toward overall water splitting without any sacrificial donor. The proposed synthetic route for controlled production of 2D g‐C₃N₄‐based structures provides a scalable alternative toward the development of highly efficient and active photocatalysts.     

Leaf‐Mosaic‐Inspired Vine‐Like Graphitic Carbon Nitride Showing High Light Absorption and Efficient Photocatalytic Hydrogen Evolution

Green plants use solar energy efficiently in nature. Simulating the exquisite structure of a natural photosynthesis system may open a new approach for the construction of desirable photocatalysts with high light harvesting efficiency and performance. Herein, inspired by the excellent light utilization of “leaf mosaic” in plants, a novel vine‐like g‐C₃N₄ (V‐CN) is synthesized for the first time by copolymerizing urea with dicyandiamide‐formaldehyde (DF) resin. The as‐prepared V‐CN exhibits ultrahigh photocatalytic hydrogen production of 13.6 mmol g^?1 h^?1 under visible light and an apparent quantum yield of 12.7% at 420 nm, which is ≈38 times higher than that of traditional g‐C₃N₄, representing one of the highest‐activity g‐C₃N₄‐based photocatalysts. This super photocatalytic performance is derived from the unique leaf mosaic structure of V‐CN, which effectively improves its light utilization and affords a larger specific surface area. In addition, the introduction of DF resin further optimizes the energy band of V‐CN, extends its light absorption, and improves its crystallinity and interfacial charge transport, resulting in high performance. It is an easy and green strategy for the preparation of broad‐spectrum, high‐performance g‐C₃N₄, which presents significant advancement for the design of other nanophotocatalysts by simulating the fine structure of natural photosynthesis.     

A Strategy for Synthesis of Carbon Nitride Induced Chemically Doped 2D MXene for High‐Performance Supercapacitor Electrodes

A step‐by‐step strategy is reported for improving capacitance of supercapacitor electrodes by synthesizing nitrogen‐doped 2D Ti₂CT_x induced by polymeric carbon nitride (p‐C₃N₄), which simultaneously acts as a nitrogen source and intercalant. The NH₂CN (cyanamide) can form p‐C₃N₄ on the surface of Ti₂CT_x nanosheets by a condensation reaction at 500–700 °C. The p‐C₃N₄ and Ti₂CT_x complexes are then heat‐treated to obtain nitrogen‐doped Ti₂CT_x nanosheets. The triazine‐based p‐C₃N₄ decomposes above 700 °C; thus, the nitrogen species can be surely doped into the internal carbon layer and/or defect site of Ti₂CT_x nanosheets at 900 °C. The extended interlayer distance and c‐lattice parameters (c‐LPs of 28.66 Å) of Ti₂CT_x prove that the p‐C₃N₄ grown between layers delaminate the nanosheets of Ti₂CT_x during the doping process. Moreover, 15.48% nitrogen doping in Ti₂CT_x improves the electrochemical performance and energy storage ability. Due to the synergetic effect of delaminated structures and heteroatom compositions, N‐doped Ti₂CT_x shows excellent characteristics as an electrochemical capacitor electrode, such as perfectly rectangular cyclic voltammetry results (CVs, R² = 0.9999), high capacitance (327 F g^?1 at 1 A g^?1, increased by ≈140% over pristine‐Ti₂CT_x), and stable long cyclic performance (96.2% capacitance retention after 5000 cycles) at high current density (5 A g^?1).     

Scalable Triple Cation Mixed Halide Perovskite–BiVO4 Tandems for Bias‐Free Water Splitting

Strong interest exists in the development of organic–inorganic lead halide perovskite photovoltaics and of photoelectrochemical (PEC) tandem absorber systems for solar fuel production. However, their scalability and durability have long been limiting factors. In this work, it is revealed how both fields can be seamlessly merged together, to obtain scalable, bias‐free solar water splitting tandem devices. For this purpose, state‐of‐the‐art cesium formamidinium methylammonium (CsFAMA) triple cation mixed halide perovskite photovoltaic cells with a nickel oxide (NiO_x) hole transport layer are employed to produce Field's metal‐epoxy encapsulated photocathodes. Their stability (up to 7 h), photocurrent density (–12.1 ± 0.3 mA cm^?2 at 0 V versus reversible hydrogen electrode, RHE), and reproducibility enable a matching combination with robust BiVO₄ photoanodes, resulting in 0.25 cm² PEC tandems with an excellent stability of up to 20 h and a bias‐free solar‐to‐hydrogen efficiency of 0.35 ± 0.14%. The high reliability of the fabrication procedures allows scaling of the devices up to 10 cm², with a slight decrease in bias‐free photocurrent density from 0.39 ± 0.15 to 0.23 ± 0.10 mA cm^?2 due to an increasing series resistance. To characterize these devices, a versatile 3D‐printed PEC cell is also developed.     

Continuous 3D Titanium Nitride Nanoshell Structure for Solar‐Driven Unbiased Biocatalytic CO2 Reduction

Z‐scheme‐inspired tandem photoelectrochemical (PEC) cells have received attention as a sustainable platform for solar‐driven CO₂ reduction. Here, continuously 3D‐structured, electrically conductive titanium nitride nanoshells (3D TiN) for biocatalytic CO₂‐to‐formate conversion in a bias‐free tandem PEC system are reported. The 3D TiN exhibits a periodically porous network with high porosity (92.1%) and conductivity (6.72 × 10⁴ S m^?1), which allows for high enzyme loading and direct electron transfer (DET) to the immobilized enzyme. It is found that the W‐containing formate dehydrogenase from Clostridium ljungdahlii (ClFDH) on the 3D TiN nanoshell is electrically activated through DET for CO₂ reduction. At a low overpotential of 40 mV, the 3D TiN‐ClFDH stably converts CO₂ to formate at a rate of 0.34 µmol h^?1 cm^?2 and a faradaic efficiency (FE) of 93.5%. Compared to a flat TiN‐ClFDH, the 3D TiN‐ClFDH shows a 58 times higher formate production rate (1.74 µmol h^?1 cm^?2) at 240 mV of overpotential. Lastly, a bias‐free biocatalytic tandem PEC cell that converted CO₂ to formate at an average rate of 0.78 µmol h^?1 and an FE of 77.3% only using solar energy and water is successfully assembled.     

Creation of 3D Textured Graphene/Si Schottky Junction Photocathode for Enhanced Photo‐Electrochemical Efficiency and Stability

This work presents a novel photo‐electrochemical architecture based on the 3D pyramid‐like graphene/p‐Si Schottky junctions. Overcoming the conventional transfer technique by which only planar graphene/Si Schottky junctions are currently available, this work demonstrates the 3D pyramid‐like graphene/p‐Si Schottky junction photocathode, which greatly enhances light harvesting efficiency and exhibits promising photo‐electrochemical performance for hydrogen generation. The formation of 3D pyramid‐like graphene/p‐Si Schottky junctions exhibits enhanced electrochemical activity and promotes charge separation efficiency compared with the bare pyramid Si surface without graphene. The inherent chemical inertness of graphene significantly improves the operational stability of 3D graphene/p‐Si Schottky junction photo‐electrochemical cells. The 3D pyramid‐like graphene/p‐Si Schottky junction photocathode delivers an onset potential of 0.41 V and a saturated photocurrent density of ?32.5 mA cm^?2 at 0 V (vs RHE) with excellent stability comparable to values reported for textured or nanostructured p‐Si photocathodes coated with ultrathin oxide layers by the conventional atomic layer deposition technique. These results suggest that the formation of graphene/Si Schottky junctions with a 3D architecture is a promising approach to improve the performance and durability of Si‐based photo‐electrochemical systems for water splitting or solar‐to‐fuel conversion.     

Metal‐Free Artificial Photosynthesis of Carbon Monoxide Using N‐Doped ZnTe Nanorod Photocathode Decorated with N‐Doped Carbon Electrocatalyst Layer

An artificial photosynthesis system based on N‐doped ZnTe nanorods decorated with an N‐doped carbon electrocatalyst layer is fabricated via an all‐solution process for the selective conversion of CO₂ to CO. Substitutional N‐doping into the ZnTe lattice decreases the bandgap slightly and improves the charge transfer characteristics, leading to enhanced photoelectrochemical activity. Remarkable N‐doping effects are also demonstrated by the N‐doped carbon layer that promotes selective CO₂‐to‐CO conversion instead of undesired water‐to‐H₂ reduction by providing active sites for CO₂ adsorption and activation, even in the absence of metallic redox centers. The photocathode shows promising performance in photocurrent generation (?1.21 mA cm^?2 at ?0.11 V_RHE), CO selectivity (dominant CO production of ≈72%), minor H₂ reduction (≈20%), and stability (corrosion suppression). The metal‐free electrocatalyst/photocatalyst combination prepared via a cost‐effective solution process exhibits high performance due to synergistic effects between them, and thus may find application in practical solar fuel production.     

A Delaminated Defect‐Rich ZrO2 Hierarchical Nanowire Photocathode for Efficient Photoelectrochemical Hydrogen Evolution

An efficient way to combat the energy crisis and the greenhouse gas effect of fossil fuels is the production of hydrogen fuel from solar‐driven water splitting reaction. Here, this study presents a p‐type ZrO₂ nanoplate‐decorated ZrO₂ nanowire photocathode with a high photoconversion efficiency that makes it potentially viable for commercial solar H₂ production. The composition of oxygen vacancy defects, low charge carrier transport property, and high specific surface area of these as‐grown hierarchical nanowires are further improved by an hydrofluoric acid (HF) treatment, which causes partial delamination and produces a thin amorphous ZrO₂ layer on the surface of the as‐grown nanostructured film. The presence of different types of oxygen vacancies (neutral, singly charged, and doubly charged defects) and their compositional correlation to the Zr^x+ oxidation states (4 > x > 2) are found to affect the charge transfer process, the p‐type conductivity, and the photocatalytic activity of the ZrO₂ nanostructured film. The resulting photocathode provides the highest overall photocurrent (?42.3 mA cm^?2 at 0 V vs reversible hydrogen electrode (RHE)) among all the photocathodes reported to date, and an outstanding 3.1% half‐cell solar‐to‐hydrogen conversion efficiency with a Faradaic efficiency of 97.8%. Even more remarkable is that the majority of the photocurrent (69%) is produced in the visible light region.     

A Sandwich‐Like Organolead Halide Perovskite Photocathode for Efficient and Durable Photoelectrochemical Hydrogen Evolution in Water

Organolead halide perovskite materials have demonstrated great potential in the solar cells field owing to their excellent optoelectronic properties. However, the instability issue of the perovskites impedes the translation of their attractive features for the solar fuel production such as photoelectrochemical H₂ production from water splitting. Herein, CH₃NH₃PbI₃ a photocathode with a sandwich‐like structure is fabricated with a general and scalable approach toward addressing this issue. The photocathode exhibits an onset potential at 0.95 V versus reversible hydrogen electrode (RHE) and a photocurrent density of ?18 mA cm^?2 at 0 V versus RHE with an impressive ideal ratiometric power‐saved efficiency of 7.63%. More impressively, the photocathode retains good stability under 12 h continuous illumination in water at wide pH range. This performance is much superior to that of the best perovskite‐based photoelectrode ever reported.     

1D Co‐Pi Modified BiVO4/ZnO Junction Cascade for Efficient Photoelectrochemical Water Cleavage

The most important factors dominating solar hydrogen synthesis efficiency include light absorption, charge separation and transport, and surface chemical reactions (charge utilization). In order to tackle these factors, an ordered 1D junction cascade photoelectrode for water splitting, grown via a simple low‐cost solution‐based process and consisting of nanoparticulate BiVO₄ on 1D ZnO rods with cobalt phosphate (Co‐Pi) on the surface is synthesized. Flat‐band measurements reveal the feasibility of charge transfer from BiVO₄ to ZnO, supported by PL measurements and photocurrent observation in the presence of an efficient hole scavenger, which demonstrate that quenching of luminescence of BiVO₄ and enhanced current are caused by electron transfer from BiVO₄ to ZnO. A dramatic cathodic shift in onset potential under both visible and full arc irradiation, coupled with a 12‐fold increase in photocurrent (ca. 3 mA cm^‐2) are observed compared to BiVO₄, resulting in ≈47% IPCE at 410 nm (4% for BiVO₄) with high solar energy conversion efficiency (0.88%). The reasons for these enhancements stem from enhanced light absorption and trapping, in situ rectifying electron transfer from BiVO₄ to ZnO, hole transfer to Co‐Pi for water oxidation, and facilitating electron transport along 1D ZnO.     

Extended Light Harvesting with Dual Cu2O‐Based Photocathodes for High Efficiency Water Splitting

Cu₂O is one of the most promising light absorbing materials for solar energy conversion. Previous studies with Cu₂O for water splitting usually deliver high photocurrent or high photovoltage, but not both. Here, a Cu₂O/Ga₂O₃/TiO₂/RuO_x photocathode that benefits from a high quality thermally oxidized Cu₂O layer and good band alignment of the Ga₂O₃ buffer layer is reported, yielding a photocurrent of 6 mA cm^?2 at 0 V versus reversible hydrogen electrode (RHE), an onset potential of 0.9 V versus RHE, and 3.5 mA cm^?2 at 0.5 V versus RHE. The quantum efficiency spectrum (incident photon to current efficiency, IPCE) reveals a dramatically improved green/red response and a decreased blue response compared with electrodeposited Cu₂O films. Light intensity dependence and photocurrent transient studies enable the identification of the limitations in the performance. Due to the complementary IPCE curves of thermally oxidized and electrodeposited Cu₂O photocathodes, a dual photocathode is fabricated to maximize the absorption over the entire range of above band gap radiation. Photocurrents of 7 mA cm^?2 at 0 V versus RHE are obtained in the dual photocathodes, with an onset potential of 0.9 V versus RHE and a thermodynamically based energy conversion efficiency of 1.9%.     

Crystal and molecular structure of hexan-2,5-dione bis(4-phenyl-thiosemicarbazonato) nickel(II), (C20H22N6S2Ni): a model study of the enhancement of the antibacterial activity of a tetradentate N,S donor ligand on metal complexation

The crystal structure of the nickel(II) complex (C₂₀H₂₂N₆S₂Ni) of the N₂S₂ ligand hexan-2,5-dionebis(4-phenyl-thiosemicarbazone) has been solved using diffractometric data. The complex, exhibiting greater antibacterial activity than the free ligand, crystallizes in the space group C2 with a = 17.414(1) Å, b = 8.485(1) Å, c = 15.129(3) Å, β = 104.09(3)°, Z = 4, d(obsd) = 1.425 g cm^?3, d(calc) = 1.438 g cm^?3 and μ(Mo-K_ga) = 10.978 cm^?1. The structure has been refined by full-matrix least squares to a final R = 0.033 and R_w = 0.041 using 1743 reflections with I ≥ 3σ(I) out of 2049 unique reflections measured (2° ≤ gq ≤ 27°). The hydrogens were either located or placed in their calculated positions. The nickel(II) ion lies in the tetrahedrally distorted square planar ligand field of the tetradentate ligand forming two five membered and one seven membered chelate rings. It is observed that the lack of conjugation in the seven membered chelate rings of the present complex and of similar complexes leads to dissymmetry in the ring geometry. The metal ion is coordinatively unsaturated and available for additional coordination in its axial directions.     

Catalytic and Dual‐Conductive Matrix Regulating the Kinetic Behaviors of Polysulfides in Flexible Li–S Batteries

The main challenge in developing foldable Li–S batteries (LSB) lies in developing an electrode that is ultraflexible, conductive, and catalytic for dissolved lithium polysulfides (LiPSs). In this paper, lightweight macromolecule graphitic carbon nitride (g‐C₃N₄) film and a conductive polymer (CP) of poly(3,4‐ethylenedioxythiophene) shell are introduced into flexible LSBs by compositing with carbon cloth (CC). In the designed hybrid of CP/g‐C₃N₄@CC, 2D g‐C₃N₄ is used in the form of an effective trapper and functions as a continuous catalytic layer for LiPSs via the formation of pyridinic‐N‐Li bonds. This is revealed by both experimental investigations and theoretical analysis. The sandwich‐like CC and CP simultaneously bring an omnidirectional conductive network for fast interfacial reaction kinetics. With these benefits, the self‐supported CP/g‐C₃N₄@CC forms a powerful interaction system to fully in situ “lock” LiPSs in the commercial CC matrix. Thus, a substantially enhanced electrochemical performance is obtained at a high sulfur loading (4.7 mg cm^–2) even operating in a pouch cell. This work may provide a potential avenue for practical use of high‐performance LSBs toward flexible energy‐storage devices.     

Fullerene as a Photoelectron Transfer Promoter Enabling Stable TiO2‐Protected Sb2Se3 Photocathodes for Photo‐Electrochemical Water Splitting

Understanding the degradation mechanisms of photoelectrodes and improving their stability are essential for fully realizing solar‐to‐hydrogen conversion via photo‐electrochemical (PEC) devices. Although amorphous TiO₂ layers have been widely employed as a protective layer on top of p‐type semiconductors to implement durable photocathodes, gradual photocurrent degradation is still unavoidable. This study elucidates the photocurrent degradation mechanisms of TiO₂‐protected Sb₂Se₃ photocathodes and proposes a novel interface‐modification methodology in which fullerene (C₆₀) is introduced as a photoelectron transfer promoter for significantly enhancing long‐term stability. It is demonstrated that the accumulation of photogenerated electrons at the surface of the TiO₂ layer induces the reductive dissolution of TiO₂, accompanied by photocurrent degradation. In addition, the insertion of the C₆₀ photoelectron transfer promoter at the Pt/TiO₂ interface facilitates the rapid transfer of photogenerated electrons out of the TiO₂ layer, thereby yielding enhanced stability. The Pt/C₆₀/TiO₂/Sb₂Se₃ device exhibits a high photocurrent density of 17 mA cm^?2 and outstanding stability over 10 h of operation, representing the best PEC performance and long‐term stability compared with previously reported Sb₂Se₃‐based photocathodes. This research not only provides in‐depth understanding of the degradation mechanisms of TiO₂‐protected photocathodes, but also suggests a new direction to achieve durable photocathodes for photo‐electrochemical water splitting.     

3D Porous Pyramid Heterostructure Array Realizing Efficient Photo‐Electrochemical Performance

Direct photo‐electrochemical (PEC) water splitting is of great practical interest for developing a sustainable energy systems, but remains a big challenge owing to sluggish charge separation, low efficiency, and poor stability. Herein, a 3D porous In₂O₃/In₂S₃ pyramid heterostructure array on a fluorine‐doped tin oxide substrate is fabricated by an ion exchange–induced synthesis strategy. Based on the synergistic structural and electronic modulations from density functional theory calculations and experimental observations, 3D porous In₂O₃/In₂S₃ photoanode by the protective layer delivers a low onset potential of ≈0.02 V versus reversible hydrogen electrode (RHE), the highest photocurrent density of 8.2 mA cm^?2 at 1.23 V versus RHE among all the In₂S₃ photoanodes reported to date, an incident photon‐to‐current efficiency of 76% at 400 nm, and high stability over 20 h for PEC water splitting are reported. This work provides an alternative promising prototype for the design and construction of novel heterostructures in robust PEC water splitting applications.     

3D Vertically Aligned Li Metal Anodes with Ultrahigh Cycling Currents and Capacities of 10 mA cm−2/20 mAh cm−2 Realized by Selective Nucleation within Microchannel Walls

Although metallic lithium is regarded as the “Holy Grail” for next‐generation rechargeable batteries due to its high theoretical capacity and low overpotential, the uncontrollable Li dendrite growth, especially under high current densities and deep plating/striping, has inhibited its practical application. Herein, a 3D‐printed, vertically aligned Li anode (3DP‐VALi) is shown to efficiently guide Li deposition via a “nucleation within microchannel walls” process, enabling a high‐performance, dendrite‐free Li anode. Moreover, the microchannels within the microwalls are beneficial for promoting fast Li⁺ diffusion, supplying large space for the accommodation of Li during the plating/stripping process. The high‐surface‐area 3D anode design enables high operating current densities and high areal capacities. As a result, the Li–Li symmetric cells using 3DP‐VALi demonstrate excellent electrochemical performances as high as 10 mA cm^?2/10 mAh cm^?2 for 1500 h and 5 mA cm^?2/20 mAh cm^?2 for 400 h, respectively. Additionally, the Li–S and Li–LiFePO₄ cells using 3DP‐VALi anodes present excellent cycling stability up to 250 and 800 cycles at a rate of 1 C, respectively. It is believed that these new findings could open a new window for dendrite‐free metal anode design and pave the way toward energy storage devices with high energy/power density.     

Ni/Fe Codoped In2S3 Nanosheet Arrays Boost Photo‐Electrochemical Performance of Planar Si Photocathodes

The photo‐electrochemical performance of the Si photocathode is seriously restricted by the severe charge recombination at the Si/electrolyte interface and sluggish hydrogen evolution reaction (HER) kinetics. Herein, a facile hydrothermal process is reported to integrate Ni/Fe codoped In₂S₃ nanosheet arrays onto the surface of unmodified a p‐Si photocathode for water reduction. The experimental results and density functional theory calculations indicate that the Ni and Fe codoping of In₂S₃ contributes to small surface transfer impedance, prolonged carrier lifetime, increased charge carrier concentration, and reduced overpotential for HER. Moreover, a p–n junction formed at the interface of Si and Ni/Fe:In₂S₃ promotes the photogenerated electron–hole separation and reduces the recombination in the bulk. As a result, the Si–Ni/Fe:In₂S₃ photocathode exhibits high performance with significantly enhanced photocurrent of ?80.9 mA cm^?2 at ?1.3 V_RHE and positive onset potential of 0.44 V_RHE.     

Oriented Transformation of Co‐LDH into 2D/3D ZIF‐67 to Achieve Co–N–C Hybrids for Efficient Overall Water Splitting

Construction of well‐defined metal–organic framework precursor is vital to derive highly efficient transition metal–carbon‐based electrocatalyst for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in water splitting. Herein, a novel strategy involving an in situ transformation of ultrathin cobalt layered double hydroxide into 2D cobalt zeolitic imidazolate framework (ZIF‐67) nanosheets grafted with 3D ZIF‐67 polyhedra supported on the surface of carbon cloth (2D/3D ZIF‐67@CC) precursor is proposed. After a low‐temperature pyrolysis, this precursor can be further converted into hybrid composites composed of ultrafine cobalt nanoparticles embedded within 2D N‐doped carbon nanosheets and 3D N‐doped hollow carbon polyhedra (Co@N‐CS/N‐HCP@CC). Experimental and density functional theory calculations results indicate that such composites have the advantages of a large number of accessible active sites, accelerated charge/mass transfer ability, the synergistic effect of components as well as an optimal water adsorption energy change. As a result, the obtained Co@N‐CS/N‐HCP@CC catalyst requires overpotentials of only 66 and 248 mV to reach a current density of 10 mA cm^?2 for HER and OER in 1.0 m KOH, respectively. Remarkably, it enables an alkali‐electrolyzer with a current density of 10 mA cm^?2 at a low cell voltage of 1.545 V, superior to that of the IrO₂@CC||Pt/C@CC couple (1.592 V).     

Metal Sulfide‐Decorated Carbon Sponge as a Highly Efficient Electrocatalyst and Absorbant for Polysulfide in High‐Loading Li2S Batteries

Owing to its high theoretical specific capacity (1166 mA h g^?1) and particularly its advantage to be paired with a lithium‐metal‐free anode, lithium sulfide (Li₂S) is regarded as a much safer cathode for next‐generation advanced lithium–sulfur (Li–S) batteries. However, the low conductivity of Li₂S and particularly the severe “polysulfide shuttle” of lithium polysulfide (LiPS) dramatically hinder their practical application in Li–S batteries. To address such issues, herein a bifuctional 3D metal sulfide‐decorated carbon sponge (3DTSC), which is constructed by 1D carbon nanowires cross‐linked with 2D graphene nanosheets with high conductivity and polar 0D metal sulfide nanodots with efficient electrocatalytic activity and strong chemical adsorption capability for LiPSs, is presented. Benefiting from the well‐designed multiscale, multidimensional 3D porous nanoarchitecture with high conductivity, and efficient electrocatalytic and absorption ability, the 3DTSC significantly mitigates LiPS shuttle, improves the utilization of Li₂S, and facilitates the transport of electrons and ions. As a result, even with a high Li₂S loading of 8 mg cm^?2, the freestanding 3DTSC‐Li₂S cathode without a polymer binder and metallic current collector delivers outstanding electrochemical performance with a high areal capacity of 8.44 mA h cm^?2.