Controlling the Active Sites of Sulfur‐Doped Carbon Nanotube–Graphene Nanolobes for Highly Efficient Oxygen Evolution and Reduction Catalysis

Controlling active sites of metal‐free catalysts is an important strategy to enhance activity of the oxygen evolution reaction (OER). Many attempts have been made to develop metal‐free catalysts, but the lack of understanding of active‐sites at the atomic‐level has slowed the design of highly active and stable metal‐free catalysts. A sequential two‐step strategy to dope sulfur into carbon nanotube–graphene nanolobes is developed. This bidoping strategy introduces stable sulfur–carbon active‐sites. Fluorescence emission of the sulfur K‐edge by X‐ray absorption near edge spectroscopy (XANES) and scanning transmission electron microscopy electron energy loss spectroscopy (STEM‐EELS) mapping and spectra confirm that increasing the incorporation of heterocyclic sulfur into the carbon ring of CNTs not only enhances OER activity with an overpotential of 350 mV at a current density of 10 mA cm^?2, but also retains 100% of stability after 75 h. The bidoped sulfur carbon nanotube–graphene nanolobes behave like the state‐of‐the‐art catalysts for OER but outperform those systems in terms of turnover frequency (TOF) which is two orders of magnitude greater than (20% Ir/C) at 400 mV overpotential with very high mass activity 1000 mA cm^?2 at 570 mV. Moreover, the sulfur bidoping strategy shows high catalytic activity for the oxygen reduction reaction (ORR). Stable bifunctional (ORR and OER) catalysts are low cost, and light‐weight bidoped sulfur carbon nanotubes are potential candidates for next‐generation metal‐free regenerative fuel cells.     

NiCoFe‐Layered Double Hydroxides/N‐Doped Graphene Oxide Array Colloid Composite as an Efficient Bifunctional Catalyst for Oxygen Electrocatalytic Reactions

Ternary NiCoFe‐layered double hydroxide (NiCo^IIIFe‐LDH) with Co³⁺ is grafted on nitrogen‐doped graphene oxide (N‐GO) by an in situ growth route. The array‐like colloid composite of NiCo^IIIFe‐LDH/N‐GO is used as a bifunctional catalyst for both oxygen evolution/reduction reactions (OER/ORR). The NiCo^IIIFe‐LDH/N‐GO array has a 3D open structure with less stacking of LDHs and an enlarged specific surface area. The hierarchical structure design and novel material chemistry endow high activity propelling O₂ redox. By exposing more amounts of Ni and Fe active sites, the NiCo^IIIFe‐LDH/N‐GO illustrates a relatively low onset potential (1.41 V vs reversible hydrogen electrode) in 0.1 mol L^?1 KOH solution under the OER process. Furthermore, by introducing high valence Co³⁺, the onset potential of this material in ORR is 0.88 V. The overvoltage difference is 0.769 V between OER and ORR. The key factors for the excellent bifunctional catalytic performance are believed to be the Co with a high valence, the N‐doping of graphene materials, and the highly exposed Ni and Fe active sites in the array‐like colloid composite. This work further demonstrates the possibility to exploit the application potential of LDHs as OER and ORR bifunctional electrochemical catalysts.     

Bimetallic Zeolitic Imidazolite Framework Derived Carbon Nanotubes Embedded with Co Nanoparticles for Efficient Bifunctional Oxygen Electrocatalyst

Bifunctional oxygen catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) with high activities and low‐cost are of prime importance and challenging in the development of fuel cells and rechargeable metal–air batteries. This study reports a porous carbon nanomaterial loaded with cobalt nanoparticles (Co@NC‐x/y) derived from pyrolysis of a Co/Zn bimetallic zeolitic imidazolite framework, which exhibits incredibly high activity as bifunctional oxygen catalysts. For instance, the optimal catalyst of Co@NC‐3/1 has the interconnected framework structure between porous carbon and embedded carbon nanotubes, which shows the superb ORR activity with onset potential of ≈1.15 V and half‐wave potential of ≈0.93 V. Moreover, it presents high OER activity that can be further enhanced to over commercial RuO₂ by P‐doped with overpotentials of 1.57 V versus reversible hydrogen electrode at 10 mA cm^?2 and long‐term stability for 2000 circles and a Tafel slope of 85 mV dec^?1. Significantly, the nanomaterial demonstrates better catalytic performance and durability than Pt/C for ORR and commercial RuO₂ and IrO₂ for OER. These findings suggest the importance of a synergistic effect of graphitic carbon, nanotubes, exposed Co–N_x active sites, and interconnected framework structure of various carbons for bifunctional oxygen electrocatalysts.     

Electronic and Defective Engineering of Electrospun CaMnO3 Nanotubes for Enhanced Oxygen Electrocatalysis in Rechargeable Zinc–Air Batteries

Rational design and massive production of bifunctional catalysts with superior oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) activities are essential for developing metal–air batteries and fuel cells. Herein, controllable large‐scale synthesis of sulfur‐doped CaMnO₃ nanotubes is demonstrated via an electrospinning technique followed by calcination and sulfurization treatment. The sulfur doping can not only replace oxygen atoms to increase intrinsic electrical conductivity but also introduce abundant oxygen vacancies to provide enough catalytically active sites, which is further demonstrated by density functional theory calculation. The resulting sulfur‐modified CaMnO₃ (CMO/S) exhibits better electrocatalytic activity for ORR and OER in alkaline solution with higher stability performance than the pristine CMO. These results highlight the importance of sulfur treatment as a facile yet effective strategy to improve the ORR and OER catalytic activity of the pristine CaMnO₃. As a proof‐of‐concept, a rechargeable Zn–air battery using the bifunctional catalyst exhibits a small charge–discharge voltage polarization, and long cycling life. Furthermore, a solid‐state flexible and rechargeable Zn–air battery gives superior discharge–charge performance and remarkable stability. Therefore, the CMO/S nanotubes might be a promising replacement to the Pt‐based electrocatalysts for metal–air batteries and fuel cells.     

Regulating the Catalytic Dynamics Through a Crystal Structure Modulation of Bimetallic Catalyst

The surface of solid catalysts is one of the most important factors where the interface with reaction products governs the reaction kinetics. Herein, the crystal phase of palladium–copper nanoparticles (PdCu NPs) is controlled to modulate their surface atomic arrangement, which will govern the growth dynamics of discharge products on their surfaces and thus the catalytic performances in non‐aqueous lithium–oxygen (Li‐O₂) batteries. First‐principles calculations and experimental validations reveal that homogeneous nucleation and distribution of discharge products are observed on the surface of body‐centered cubic PdCu NPs, promoting the oxygen reduction/evolution reaction (ORR/OER) activities in Li‐O₂ batteries. However, the agglomerates formed on the surface of its face‐centered cubic homologue deteriorates ORR/OER activities, which worsen the battery performances. For the first time, this work theoretically and experimentally demonstrates how the crystal phase modulation regulates the nucleation behaviors and growth dynamics of discharge products for ORR/OER.     

High‐Performance Trifunctional Electrocatalysts Based on FeCo/Co2P Hybrid Nanoparticles for Zinc–Air Battery and Self‐Powered Overall Water Splitting

Currently, it is still a significant challenge to simultaneously boost various reactions by one electrocatalyst with high activity, excellent durability, as well as low cost. Herein, hybrid trifunctional electrocatalysts are explored via a facile one‐pot strategy toward an efficient oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER). The catalysts are rationally designed to be composed by FeCo nanoparticles encapsuled in graphitic carbon films, Co₂P nanoparticles, and N,P‐codoped carbon nanofiber networks. The FeCo nanoparticles and the synergistic effect from Co₂P and FeCo nanoparticles make the dominant contributions to the ORR, OER, and HER activities, respectively. Their bifunctional activity parameter (?E) for ORR and OER is low to 0.77 V, which is much smaller than those of most nonprecious metal catalysts ever reported, and comparable with state‐of‐the‐art Pt/C and RuO₂ (0.78 V). Accordingly, the as‐assembled Zn–air battery exhibits a high power density of 154 mW cm^?2 with a low charge–discharge voltage gap of 0.83 V (at 10 mA cm^?2) and excellent stability. The as‐constructed overall water‐splitting cell achieves a current density of 10 mA cm^?2 (at 1.68 V), which is comparable to the best reported trifunctional catalysts.     

NiFe Layered Double Hydroxide Nanoparticles on Co,N‐Codoped Carbon Nanoframes as Efficient Bifunctional Catalysts for Rechargeable Zinc–Air Batteries

The future large‐scale deployment of rechargeable zinc–air batteries requires the development of cheap, stable, and efficient bifunctional electrocatalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). In this work, a highly efficient bifunctional electrocatalyst is prepared by depositing 3–5 nm NiFe layered double hydroxide (NiFe‐LDH) nanoparticles on Co,N‐codoped carbon nanoframes (Co,N‐CNF). The NiFe‐LDH/Co,N‐CNF electrocatalyst displayed an OER overpotential of 0.312 V at 10 mA cm^?2 and an ORR half‐wave potential of 0.790 V. The outstanding performance of the electrocatalyst is attributable to the high electrical conductivity and excellent ORR activity of Co,N‐CNF, together with the strong anchoring of 3–5 nm NiFe‐LDH nanoparticles, which preserves active sites. Inspired by the excellent OER and ORR performance of NiFe‐LDH/Co,N‐CNF, a prototype rechargeable zinc–air battery is developed. The battery exhibited a low discharge–charge voltage gap (1.0 V at 25 mA cm^?2) and long‐term cycling durability (over 80 h), and superior overall performance to a counterpart battery constructed using a mixture of IrO₂ and Pt/C as the cathode. The strategy developed here can easily be adapted to synthesize other bifunctional CNF‐based hybrid electrodes for ORR and OER, providing a practical route to more efficient rechargeable zinc–air batteries.     

Single‐Atom to Single‐Atom Grafting of Pt1 onto FeN4 Center: Pt1@FeNC Multifunctional Electrocatalyst with Significantly Enhanced Properties

Nonprecious metal catalysts (NPMCs) Fe?N?C are promising alternatives to noble metal Pt as the oxygen reduction reaction (ORR) catalysts for proton‐exchange‐membrane fuel cells. Herein, a new modulation strategy is reported to the active moiety Fe?N₄ via a precise “single‐atom to single‐atom” grafting of a Pt atom onto the Fe center through a bridging oxygen molecule, creating a new active moiety of Pt₁?O₂?Fe₁?N₄. The modulated Fe?N?C exhibits remarkably improved ORR stabilities in acidic media. Moreover, it shows unexpectedly high catalytic activities toward oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), with overpotentials of 310 mV for OER in alkaline solution and 60 mV for HER in acidic media at a current density of 10 mA cm^?2, outperforming the benchmark RuO₂ and comparable with Pt/C(20%), respectively. The enhanced multifunctional electrocatalytic properties are associated with the newly constructed active moiety Pt₁?O₂?Fe₁?N₄, which protects Fe sites from harmful species. Density functional theory calculations reveal the synergy in the new active moiety, which promotes the proton adsorption and reduction kinetics. In addition, the grafted Pt₁?O₂? dangling bonds may boost the OER activity. This study paves a new way to improve and extend NPMCs electrocatalytic properties through a precisely single‐atom to single‐atom grafting strategy.     

Trifunctional Electrocatalysis on Dual‐Doped Graphene Nanorings–Integrated Boxes for Efficient Water Splitting and Zn–Air Batteries

Despite the exciting achievements made in synthesis of monofunctional electrocatalysts for oxygen reduction reaction (ORR), oxygen evolution reaction (OER), or hydrogen evolution reaction (HER), it is challenging to develop trifunctional electrocatalysts for both ORR/OER/HER. Herein, N, O‐codoped graphene nanorings‐integrated boxes (denoted NOGB) are crafted via high‐temperature pyrolysis and following acid etching of hybrid precursors containing polymers and Prussian blue analogue cubes. The electrochemical results signified that the resulting NOGB‐800 (800 refers to pyrolysis temperature) is highly active for trifunctional electrocatalysis of ORR/OER/HER. This can be reasonably attributed to the advanced nanostructures (i.e., the hierarchically porous nanostructures on the hollow nanorings) and unique chemical compositions (i.e., N, O‐codoped graphene). More attractively, the rechargeable Zn–air battery based on NOGB‐800 displays maximum power density of 111.9 mW cm^?2 with small charge–discharge potential of 0.72 V and excellent stability of 30 h, comparable with the Pt/C+Ir/C counterpart. The NOGB‐800 could also be utilized as bifunctional electrocatalysts for overall water splitting to yield current density of 10 mA cm^?2 at a voltage of 1.65 V, surpassing most reported electrocatalysts. Therefore, the NOGB‐800 is a promising candidate instead of precious metal–based electrocatalysts for the efficient Zn–air battery and water splitting.     

Sandwich‐Like Reduced Graphene Oxide/Carbon Black/Amorphous Cobalt Borate Nanocomposites as Bifunctional Cathode Electrocatalyst in Rechargeable Zinc‐Air Batteries

The inhibitively high cost of the noble‐metal‐containing materials has become a major obstacle for the large‐scale application of rechargeable zinc‐air batteries (ZABs). To solve this problem in a practical way, a green and scalable method to prepare sandwich‐like reduced graphene oxide /carbon black/amorphous cobalt borate nanocomposites (rGO/CB/Co‐B_i) is reported. These composites are shown to be a highly efficient and robust bifunctional electrocatalyst for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). In this system, the spontaneous assembly of the GO sheet and CB nanoparticles is demonstrated by noncovalent interactions to build the sandwich‐like structure with hierarchical pore distribution. The impressive ORR and OER activities of the obtained nanocomposite are attributed to the high conductivity, large surface area, and the hierarchically porous channels. With room‐temperature synthesis and significant activities shown in the demonstrative battery test, the prepared nanocomposite can potentially serve as an alternative for noble‐metal‐based rechargeable ZAB cathode materials.     

Superior Oxygen Reduction Reaction on Phosphorus‐Doped Carbon Dot/Graphene Aerogel for All‐Solid‐State Flexible Al–Air Batteries

Carbon dots have been recognized as one of the most promising candidates for the oxygen reduction reaction (ORR) in alkaline media. However, the desired ORR performance in metal–air batteries is often limited by the moderate electrocatalytic activity and the lack of a method to realize good dispersion. To address these issues, herein a biomass‐deriving method is reported to achieve the in situ phosphorus doping (P‐doping) of carbon dots and their simultaneous decoration onto graphene matrix. The resultant product, namely P‐doped carbon dot/graphene (P‐CD/G) nanocomposites, can reach an ultrahigh P‐doping level for carbon nanomaterials. The P‐CD/G nanocomposites are found to exhibit excellent ORR activity, which is highly comparable to the commercial Pt/C catalysts. When used as the cathode materials for a primary liquid Al–air battery, the device shows an impressive power density of 157.3 mW cm^?2 (comparing to 151.5 mW cm^?2 of a similar Pt/C battery). Finally, an all‐solid‐state flexible Al–air battery is designed and fabricated based on our new nanocomposites. The device exhibits a stable discharge voltage of ≈1.2 V upon different bending states. This study introduces a unique biomass‐derived material system to replace the noble metal catalysts for future portable and wearable electronic devices.     

Interpenetrating Triphase Cobalt‐Based Nanocomposites as Efficient Bifunctional Oxygen Electrocatalysts for Long‐Lasting Rechargeable Zn–Air Batteries

Rational construction of atomic‐scale interfaces in multiphase nanocomposites is an intriguing and challenging approach to developing advanced catalysts for both oxygen reduction (ORR) and evolution reactions (OER). Herein, a hybrid of interpenetrating metallic Co and spinel Co₃O₄ “Janus” nanoparticles stitched in porous graphitized shells (Co/Co₃O₄@PGS) is synthesized via ionic exchange and redox between Co²⁺ and 2D metal–organic‐framework nanosheets. This strategy is proven to effectively establish highways for the transfer of electrons and reactants within the hybrid through interfacial engineering. Specifically, the phase interpenetration of mixed Co species and encapsulating porous graphitized shells provides an optimal charge/mass transport environment. Furthermore, the defect‐rich interfaces act as atomic‐traps to achieve exceptional adsorption capability for oxygen reactants. Finally, robust coupling between Co and N through intimate covalent bonds prohibits the detachment of nanoparticles. As a result, Co/Co₃O₄@PGS outperforms state‐of‐the‐art noble‐metal catalysts with a positive half‐wave potential of 0.89 V for ORR and a low potential of 1.58 V at 10 mA cm^?2 for OER. In a practical demonstration, ultrastable cyclability with a record lifetime of over 800 h at 10 mA cm^?2 is achieved by Zn–air batteries with Co/Co₃O₄@PGS within the rechargeable air electrode.     

Ultralow Ru Loading Transition Metal Phosphides as High‐Efficient Bifunctional Electrocatalyst for a Solar‐to‐Hydrogen Generation System

Water splitting is a promising technology for sustainable conversion of hydrogen energy. The rational design of oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) bifunctional electrocatalysts with superior activity and stability in the same electrolyte is the key to promoting their large‐scale applications. Herein, an ultralow Ru (1.08 wt%) transition metal phosphide on nickel foam (Ru–MnFeP/NF) derived from Prussian blue analogue, that effectively drivies both the OER and the HER in 1 m KOH, is reported. To reach 20 mA cm^?2 for OER and 10 mA cm^?2 for HER, the Ru–MnFeP/NF electrode only requires overpotentials of 191 and 35 mV, respectively. Such high electrocatalytic activity exceeds most transition metal phosphides for the OER and the HER, and even reaches Pt‐like HER electrocatalytic levels. Accordingly, it significantly accelerates full water splitting at 10 mA cm^?2 with 1.470 V, which outperforms that of the integrated RuO₂ and Pt/C couple electrode (1.560 V). In addition, the extremely long operational stability (50 h) and the successful demonstration of a solar‐to‐hydrogen generation system through full water splitting provide more flexibility for large‐scale applications of Ru–MnFeP/NF catalysts.     

Graphitic Nanoshell/Mesoporous Carbon Nanohybrids as Highly Efficient and Stable Bifunctional Oxygen Electrocatalysts for Rechargeable Aqueous Na–Air Batteries

Efficient and cost‐effective bifunctional electrocatalysts for oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) are of vital importance in energy conversion and storage devices. Despite the recent progress in bifunctional oxygen electrocatalysts, their unbalanced and insufficient OER and ORR activities has continued to pose challenges for the practical application of such energy devices. The design of highly integrated, high‐performance, bifunctional oxygen electrocatalysts composed of highly graphitic nanoshells embedded in mesoporous carbon (GNS/MC) is reported. The GNS/MC exhibits very high oxygen electrode activity, which is one of the best performances among nonprecious metal bifunctional oxygen electrocatalysts, and substantially outperforms Ir‐ and Pt‐based catalysts. Moreover, the GNS/MC shows excellent durability for both OER and ORR. In situ X‐ray absorption spectroscopy and square wave voltammetry reveal the roles of residual Ni and Fe entities in enhancing OER and ORR activities. Raman spectra indicate highly graphitic, defect‐rich nature of the GNS/MC, which can contribute to the enhanced OER activity and to high stability for the OER and ORR. In aqueous Na–air battery tests, the GNS/MC air cathode‐based cell exhibits superior performance to Ir/C‐ and Pt/C‐based batteries. Significantly, the GNS/MC‐based cell demonstrates the first example of rechargeable aqueous Na–air battery.     

Single‐Atom to Single‐Atom Grafting of Pt1 onto Fe?N4 Center: Pt1@Fe?N?C Multifunctional Electrocatalyst with Significantly Enhanced Properties

Nonprecious metal catalysts (NPMCs) Fe? N? C are promising alternatives to noble metal Pt as the oxygen reduction reaction (ORR) catalysts for proton‐exchange‐membrane fuel cells. Herein, a new modulation strategy is reported to the active moiety Fe? N₄ via a precise “single‐atom to single‐atom” grafting of a Pt atom onto the Fe center through a bridging oxygen molecule, creating a new active moiety of Pt₁? O₂? Fe₁? N₄. The modulated Fe? N? C exhibits remarkably improved ORR stabilities in acidic media. Moreover, it shows unexpectedly high catalytic activities toward oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), with overpotentials of 310 mV for OER in alkaline solution and 60 mV for HER in acidic media at a current density of 10 mA cm^?2, outperforming the benchmark RuO₂ and comparable with Pt/C(20%), respectively. The enhanced multifunctional electrocatalytic properties are associated with the newly constructed active moiety Pt₁? O₂? Fe₁? N₄, which protects Fe sites from harmful species. Density functional theory calculations reveal the synergy in the new active moiety, which promotes the proton adsorption and reduction kinetics. In addition, the grafted Pt₁? O₂? dangling bonds may boost the OER activity. This study paves a new way to improve and extend NPMCs electrocatalytic properties through a precisely single‐atom to single‐atom grafting strategy.     

Novel Route to Fe‐Based Cathode as an Efficient Bifunctional Catalysts for Rechargeable Zn–Air Battery

Efficient bifunctional oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts are of great importance for rechargeable metal–air batteries. Herein, FeN_x/C catalysts are synthesized by pyrolysis of thiourea and agarose containing α‐Fe₂O₃ nanoplate as Fe precursor, where α‐Fe₂O₃ nanoplate can prevent the aggregation of carbon sheets to effectively improve the specific surface area during the carbonization process. The FeN_x/C‐700‐20 catalyst displays excellent catalytic performance for both ORR and OER activity in alkaline conditions with more positive onset potential (1.1 V vs the reversible hydrogen electrode) and half‐wave potential, higher stability, and stronger methanol tolerance in alkaline solution, which are all superior to that of the commercial Pt/C catalyst. In this study, the detailed analyses demonstrate that the coexistence of Fe‐based species and high content of Fe‐N_x both play an important role for the catalytic activity. Furthermore, FeN_x/C‐700‐20 as cathode catalyst in Zn–air battery possesses higher charge–discharge stability and power density compared with that of commercial Pt/C catalyst, displaying great potential in practical implementation of for the rechargeable energy devices.     

Pt‐Ir‐Pd Trimetallic Nanocages as a Dual Catalyst for Efficient Oxygen Reduction and Evolution Reactions in Acidic Media

The development of dual catalysts with high efficiency toward oxygen reduction and evolution reactions (ORR and OER) in acidic media is a significant challenge. Here an active and durable dual catalyst based upon cubic Pt₃₉Ir₁₀Pd₁₁ nanocages with an average edge length of 12.3 nm, porous walls as thin as 1.0 nm, and well‐defined {100} facets is reported. The trimetallic nanocages perform better than all the reported dual catalysts in acidic media, with a low ORR‐OER overpotential gap of only 704 mV at a Pt‐Ir‐Pd loading of 16.8 µg_Pt+Ir+Pd cm^?2_geo. For ORR at 0.9 V, when benchmarked against the commercial Pt/C and Pt‐Pd nanocages, the trimetallic nanocages exhibit an enhanced mass activity of 0.52 A mg^?1_Pt+Ir+Pd (about four and two times as high as those of the Pt/C and Pt‐Pd nanocages) and much improved durability. For OER, the trimetallic nanocages show a remarkable mass activity of 0.20 A mg^?1_Pt+Ir at 1.53 V, which is 16.7 and 4.3 fold relative to those of the Pt/C and Pt‐Pd nanocages, respectively. These improvements can be ascribed to the highly open structure of the nanocages, and the possible electronic coupling between Ir and Pt atoms in the lattice.     

Defective Carbon–CoP Nanoparticles Hybrids with Interfacial Charges Polarization for Efficient Bifunctional Oxygen Electrocatalysis

The development of efficient catalysts for both oxygen reduction and evolution reactions (oxygen reduction reaction (ORR) and oxygen evolution reaction (OER)) is central to regenerative fuel cells and rechargeable metal–air batteries. It is highly desirable to achieve the efficient integration of dual active components into the catalysts and to understand the interaction between the dual components. Here, a facile approach is demonstrated to construct defective carbon–CoP nanoparticle hybrids as bifunctional oxygen electrocatalysts, and further probe the interfacial charge distribution behavior. By combining multiple synchrotron‐based X‐ray spectroscopic characterizations with density functional theory calculations, the interfacial charge polarization with the electrons gathering at the defective carbon surface and the holes gathering at the CoP surface due to strong interfacial coupling is revealed, which simultaneously facilitates the ORR and OER with remarkable bifunctional oxygen electrode activities. This work not only offers a bifunctional oxygen catalyst with outstanding performance, but also unravels the promoting factor of the hybrids from the view of interfacial charge distribution.     

Atomically Dispersed Fe‐Nx/C Electrocatalyst Boosts Oxygen Catalysis via a New Metal‐Organic Polymer Supramolecule Strategy

The development of high‐performance oxygen reduction reaction (ORR) catalysts derived from non‐Pt group metals (non‐PGMs) is urgent for the wide applications of proton exchange membrane fuel cells (PEMFCs). In this work, a facile and cost‐efficient supramolecular route is developed for making non‐PGM ORR catalyst with atomically dispersed Fe‐N_x/C sites through pyrolyzing the metal‐organic polymer coordinative hydrogel formed between Fe³⁺ and α‐L‐guluronate blocks of sodium alginate (SA). High‐angle annular dark field scanning transmission electron microscopy (HAADF‐STEM) and X‐ray absorption spectroscopy (XAS) verify that Fe atoms achieve atomic‐level dispersion on the obtained SA‐Fe‐N nanosheets and a possible fourfold coordination with N atoms. The best‐performing SA‐Fe‐N catalyst exhibits excellent ORR activity with half‐wave potential (E_1/2) of 0.812 and 0.910 V versus the reversible hydrogen electrode (RHE) in 0.5 m H₂SO₄ and 0.1 m KOH, respectively, along with respectable durability. Such performance surpasses that of most reported non‐PGM ORR catalysts. Density functional theory calculations suggest that the relieved passivation effect of OH* on Fe‐N₄/C structure leads to its superior ORR activity to Pt/C in alkaline solution. The work demonstrates a novel strategy for developing high‐performance non‐PGM ORR electrocatalysts with atomically dispersed and stable M‐N_x coordination sites in both acidic and alkaline media.     

Highly Active and Stable Graphene Tubes Decorated with FeCoNi Alloy Nanoparticles via a Template‐Free Graphitization for Bifunctional Oxygen Reduction and Evolution

Development of highly active and stable bifunctional oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts from earth‐abundant elements remains a grand challenge for highly demanded reversible fuel cells and metal–air batteries. Carbon catalysts have many advantages over others due to their low cost, excellent electrical conductivity, high surface area, and easy functionalization. However, they typically cannot withstand the highly oxidative OER environment. Here, a new class of bifunctional electrocatalyst is reported, consisting of ultralarge sized nitrogen doped graphene tubes (N‐GTs) (>500 nm) decorated with FeCoNi alloy particles. These tubes are prepared from an inexpensive precursor, dicyandiamide, via a template‐free graphitization process. The ORR/OER activity and the stability of these graphene tube catalysts depend strongly on the transition metal precursors. The best performing FeCoNi‐derived N‐GT catalyst exhibits excellent ORR and OER activity along with adequate electrochemical durability over a wide potential window (0–1.9 V) in alkaline media. The measured OER current is solely due to desirable O₂ evolution, rather than carbon oxidation. Extensive electrochemical and physical characterization indicated that high graphitization degree, thicker tube walls, proper nitrogen doping, and presence of FeCoNi alloy particles are vital for high bifunctional activity and electrochemical durability of tubular carbon catalysts.