Large Power Amplification in Magneto‐Mechano‐Electric Harvesters through Distributed Forcing

Energy harvesting from extremely low frequency magnetic fields using magneto‐mechano‐electric (MME) harvesters enables wireless power transfer for operating Internet of Things (IoT) devices. The MME harvesters are designed to resonate at a fixed frequency by absorbing AC magnetic fields through a composite cantilever comprising of piezoelectric and magnetostrictive materials, and a permanent magnetic tip mass. However, this harvester architecture limits power generation because volume of the magnetic end mass is closely coupled with the resonance frequency of the device structure. Here, a method is demonstrated for maintaining the resonance frequency of the MME harvesters under all operating conditions (e.g., 60 Hz, standard frequency of electricity in many countries) while simultaneously enhancing the output power generation. By distributing the magnetic mass over the beam, the output power of the harvester is significantly enhanced at a constant resonance frequency. The MME harvester with distributed forcing shows 280% improvement in the power generation compared with a traditional architecture. The generated power is shown to be sufficient to power eight different onboard sensors with wireless data transmission integrated on a drone. These results demonstrate the promise of MME energy harvesters for powering wireless communication and IoT sensors.     

Natural Leaf Made Triboelectric Nanogenerator for Harvesting Environmental Mechanical Energy

Distributed environmental mechanical energy is rarely collected due to its fluctuating amplitudes and low frequency, which is usually attributed as “random” energy. Considering the rapid development of the Internet of things (IoT), there is a great need for a large number of distributed and sustainable power sources. Here, a natural leaf assembled triboelectric nanogenerator (Leaf‐TENG) is designed by utilizing the green leaf as an electrification layer and electrode to effectively harvest environmental mechanical energy. The Leaf‐TENG with good adaptability has the maximum output power of ≈45 mW m^?2, which is capable of driving advertising LEDs and commercial electronic temperature sensors. Besides, a tree‐shaped energy harvester is integrated with natural Leaf‐TENG to harvest large‐area environmental mechanical energy. This work provides a new prospect for distributed and environmental‐friendly power sources and has potential applications in the IoT and self‐powered systems.     

Indoor Thin‐Film Photovoltaics: Progress and Challenges

Energy generation and consumption have always been an important component of social development. Interests in this field are beginning to shift to indoor photovoltaics (IPV) which can serve as power sources under low light conditions to meet the energy needs of rapidly growing fields, such as intelligence gathering and information processing which usually operate via the Internet‐of‐things (IoT). Since the power requirements for this purpose continue to decrease, IPV systems under low light may facilitate the realization of self‐powered high‐tech electronic devices connected through the IoT. This review discusses and compares the characteristics of different types of IPV devices such as those based on silicon, dye, III‐V semiconductors, organic compounds, and halide perovskites. Among them, specific attention is paid to perovskite photovoltaics which may potentially become a high performing IPV system due to the fascinating photophysics of the halide perovskite active layer. The limitations of such indoor application as they relate to the toxicity, stability, and electronic structure of halide perovskites are also discussed. Finally, strategies which could produce highly functional, nontoxic, and stable perovskite photovoltaics devices for indoor applications are proposed.     

Generating Electricity during Walking with a Lower Limb-Driven Energy Harvester: Targeting a Minimum User Effort

Background

Much research in the field of energy harvesting has sought to develop devices capable of generating electricity during daily activities with minimum user effort. No previous study has considered the metabolic cost of carrying the harvester when determining the energetic effects it has on the user. When considering device carrying costs, no energy harvester to date has demonstrated the ability to generate a substantial amount of electricity (> 5W) while maintaining a user effort at the same level or lower than conventional power generation methods (e.g. hand crank generator).

Methodology/Principal Findings

We developed a lower limb-driven energy harvester that is able to generate approximately 9W of electricity. To quantify the performance of the harvester, we introduced a new performance measure, total cost of harvesting (TCOH), which evaluates a harvester’s overall efficiency in generating electricity including the device carrying cost. The new harvester captured the motion from both lower limbs and operated in the generative braking mode to assist the knee flexor muscles in slowing the lower limbs. From a testing on 10 participants under different walking conditions, the harvester achieved an average TCOH of 6.1, which is comparable to the estimated TCOH for a conventional power generation method of 6.2. When generating 5.2W of electricity, the TCOH of the lower limb-driven energy harvester (4.0) is lower than that of conventional power generation methods.

Conclusions/Significance

These results demonstrated that the lower limb-driven energy harvester is an energetically effective option for generating electricity during daily activities.     

Multilayered‐Electrode‐Based Triboelectric Nanogenerators with Managed Output Voltage and Multifold Enhanced Charge Transport

The open‐circuit voltage of a triboelectric nanogenerator (TENG) increases with the tribo‐charge density and the separated distance between two tribo‐surfaces, which can reach several thousand volts and is much higher than the working voltage required by most electrical devices and energy storage units. Therefore, improving the effective efficiency of TENGs requires reducing the output voltage and enhancing the transferred charges. Here, a multilayered‐electrode‐based TENG (ME‐TENG) is developed in which the output voltage can be managed by controlling the charge flow in a process of multiple (N) steps, which results in N times lower voltage but N times higher total charge transport. The ME‐TENG is demonstrated to work in various modes, including multichannel, single‐channel, and double‐tribo‐surface structures. The effects of insulator layer thickness and total layer number on the output voltage are simulated by the finite element method. The output voltage can be modulated from 14 to 102 V by changing the insulator layer number between two adjacent working electrodes, based on which the 8‐bit logic representations of the characters in the ACSII code table are demonstrated. The ME‐TENG provides a novel method to manage the output power and has potential applications in self‐powered sensors array and human–machine interfacing with logic communications.     

Triboelectric Nanogenerator: A Foundation of the Energy for the New Era

As the world is marching into the era of the internet of things (IoTs) and artificial intelligence, the most vital development for hardware is a multifunctional array of sensing systems, which forms the foundation of the fourth industrial revolution toward an intelligent world. Given the need for mobility of these multitudes of sensors, the success of the IoTs calls for distributed energy sources, which can be provided by solar, thermal, wind, and mechanical triggering/vibrations. The triboelectric nanogenerator (TENG) for mechanical energy harvesting developed by Z.L. Wang's group is one of the best choices for this energy for the new era, since triboelectrification is a universal and ubiquitous effect with an abundant choice of materials. The development of self‐powered active sensors enabled by TENGs is revolutionary compared to externally powered passive sensors, similar to the advance from wired to wireless communication. In this paper, the fundamental theory, experiments, and applications of TENGs are reviewed as a foundation of the energy for the new era with four major application fields: micro/nano power sources, self‐powered sensors, large‐scale blue energy, and direct high‐voltage power sources. A roadmap is proposed for the research and commercialization of TENG in the next 10 years.     

High‐Efficiency and Reliable Smart Photovoltaic Windows Enabled by Multiresponsive Liquid Crystal Composite Films and Semi‐Transparent Perovskite Solar Cells

Smart photovoltaic windows (SPWs) are functional devices possessing the capabilities of electrical power output, energy saving, and privacy protection by managing sunlight under external stimuli and potentially applicable in the fields of energy‐saving buildings, automobiles, and switchable optoelectronics. However, long response time, low power conversion efficiency (PCE), poor stability and cycling performance, and monostimuli responsive behavior restrict their practical applications. To address these issues, high‐efficiency and reliable SPWs are demonstrated by coupling multiresponsive liquid crystal/polymer composite (LCPC) films and semi‐transparent perovskite solar cells (ST‐PSCs). In this design, fast and multiple stimuli‐responsive LCPC films are utilized as an inside layer to control the transparency of SPWs. The ST‐PSCs with competitive PCE and qualified transparency acting as an outside layer offer energy generation functionality. Benefiting from repeatable transparency transition modulated by external stimuli, a series of working modes are achieved in the SPWs providing distinguished and stable energy generation, energy saving, and privacy protection performances.     

Thermally Chargeable Solid‐State Supercapacitor

Ubiquitous low‐grade thermal energy, which is typically wasted without use, can be extremely valuable for continuously powering electronic devices such as sensors and wearable electronics. A popular choice for waste heat recovery has been thermoelectric energy conversion, but small output voltage without energy‐storing capability necessitates additional components such as a voltage booster and a capacitor. Here, a novel method of simultaneously generating a large voltage from a temperature gradient and storing electrical energy without losing the benefit of solid‐state no‐moving part devices like conventional thermoelectrics is reported. Thermally driven ion diffusion is used to greatly increase the output voltage (8 mV K^?1) with polystyrene sulfonic acid (PSSH) film. Polyaniline‐coated electrodes containing graphene and carbon nanotube sandwich the PSSH film where thermally induced voltage‐enabled electrochemical reactions, resulting in a charging behavior without an external power supply. With a small temperature difference (5 K) possibly created over wearable energy harvesting devices, the thermally chargeable supercapacitor produce 38 mV with a large areal capacitance (1200 F m^?2). It is anticipated that the attempt with thermally driven ion diffusion behaviors initiates a new research direction in thermal energy harvesting.     

Jabuticaba‐Inspired Hybrid Carbon Filler/Polymer Electrode for Use in Highly Stretchable Aqueous Li‐Ion Batteries

Stretchable electronics are considered as next‐generation devices; however, to realize stretchable electronics, it is first necessary to develop a deformable energy device. Of the various components in energy devices, the fabrication of stretchable current collectors is crucial because they must be mechanically robust and have high electrical conductivity under deformation. In this study, the authors present a conductive polymer composite composed of Jabuticaba‐like hybrid carbon fillers containing carbon nanotubes and carbon black in a simple solution process. The hybrid carbon/polymer (HCP) composite is found to effectively retain its electrical conductivity, even when under high strain of ≈200%. To understand the behavior of conductive fillers in the polymer matrix when under mechanical strain, the authors investigate the microstructure of the composite using an in situ small‐angle X‐ray scattering analysis. The authors observe that the HCP produces efficient electrical pathways for filler interconnections upon stretching. The authors develop a stretchable aqueous rechargeable lithium‐ion battery (ARLB) that utilizes this HCP composite as a stretchable current collector. The ARLB exhibits excellent rate capability (≈90 mA h g^?1 at a rate of 20 C) and outstanding capacity retention of 93% after 500 cycles. Moreover, the stretchable ARLB is able to efficiently deliver power even when under 100% strain.     

A fully electronic sensor for the measurement of cDNA hybridization kinetics

Ion sensitive field effect transistors (ISFET) are candidates for a new generation of fully electrical DNA sensors. To this purpose, we have modified ISFET sensors by adsorbing on their Si(3)N(4) surface poly-L-lysine and single (as well as double) stranded DNA. Once coupled to an accurate model of the oppositely charged layers adsorbed on the surface, the proposed sensor allows quantitatively evaluating the adsorbed molecules densities, as well as estimating DNA hybridization kinetics.     

Analysing a magnetic molecule detection system--computer simulation

The detection of single molecules, e.g. in biology is possible by marking the interesting molecules with magnetic beads and detect the influence of the beads on giant magnetoresistance (GMR)/tunnel magnetoresistance (TMR)/spin valve (SV) sensors. The development of suitable multilayers has been studied experimentally as well as theoretically in order to optimize the sensor parameters. A finite difference (FD) method including the usually used contributions to the total energy [exchange, antiferromagnetically (af) coupling, anisotropy and magnetostatic] is used for the simulation with additional contributions to the local field according to the stray fields of the beads. In this work, we will show the results of micromagnetic calculations of the magnetization behavior of GMR/TMR sensors considering also the interaction between the domains in the magnetic layers of the sensor and the bead area. We can present first calculations where the bead particles (signal source) and the magnetic layers (sensor device) are considered as a whole magnetic ensemble.     

Versatile Core–Sheath Yarn for Sustainable Biomechanical Energy Harvesting and Real‐Time Human‐Interactive Sensing

The emergence of stretchable textile‐based mechanical energy harvester and self‐powered active sensor brings a new life for wearable functional electronics. However, single energy conversion mode and weak sensing capabilities have largely hindered their development. Here, in virtue of silver‐coated nylon yarn and silicone rubber elastomer, a highly stretchable yarn‐based triboelectric nanogenerator (TENG) with coaxial core–sheath and built‐in spring‐like spiral winding structures is designed for biomechanical energy harvesting and real‐time human‐interactive sensing. Based on the two advanced structural designs, the yarn‐based TENG can effectively harvest or respond rapidly to omnifarious external mechanical stimuli, such as compressing, stretching, bending, and twisting. With these excellent performances, the yarn‐based TENG can be used in a self‐counting skipping rope, a self‐powered gesture‐recognizing glove, and a real‐time golf scoring system. Furthermore, the yarn‐based TENG can also be woven into a large‐area energy‐harvesting fabric, which is capable of lighting up light emitting diodes (LEDs), charging a commercial capacitor, powering a smart watch, and integrating the four operational modes of TENGs together. This work provides a new direction for textile‐based multimode mechanical energy harvesters and highly sensitive self‐powered motion sensors with potential applications in sustainable power supplies, self‐powered wearable electronics, personalized motion/health monitoring, and real‐time human‐machine interactions.     

Design,construction, and validation of a large capacity rodent magnetic field exposure laboratory

A magnetic field exposure laboratory has been constructed to support National Toxicology Program studies for the evaluation of the toxicity and carcinogenicity of pure, linearly polarized, 60 Hz magnetic fields in rodents. This dual corridor, controlled access facility can support the simultaneous exposure of 1200 rats and 1200 mice. The facility contains fully redundant electrical and environmental control systems and was constructed using non‐metallic materials to maintain low levels of background (ambient), stray, and cross‐talk magnetic fields. The exposure module design provides for large uniform exposure volumes with good control of stray and cross‐talk fields, while allowing the use of roll‐around cage racks for simplified animal husbandry. Stray fields and cross‐talk have been further reduced by the inclusion of “steering coils” in each exposure module. Ambient 60 Hz fields (less cross‐talk) in all exposure rooms are <0.1 μT (1 mG), and static magnetic fields have been mapped extensively. Magnetic field strength, waveform, temperature, relative humidity, light intensity, noise level, vibration, and air flow in all animal holding areas are tightly regulated, and are monitored continuously during all studies. Field uniformity in the animal exposure volumes is better than ±10%; a systematic program of cage, rack, and room rotation controls for possible positional effects within the exposure system. Magnetic fields are turned on and off over multiple cycles to prevent the induction of transients associated with abrupt field level changes. Total harmonic distortion is <3% at all field strengths. The facility has been used to study magnetic field bioeffects in rodent model systems in experiments ranging in duration from 8 weeks to 2 years. Bioelectromagnetics 20:13–23, 1999. © 1999 Wiley‐Liss, Inc.     

Honeycomb Structure Inspired Triboelectric Nanogenerator for Highly Effective Vibration Energy Harvesting and Self‐Powered Engine Condition Monitoring

Vibration in mechanical equipment can serve as a sustainable energy source to power sensors and devices if it can be effectively collected. In this work, a honeycomb structure inspired triboelectric nanogenerator (HSI‐TENG) consisting of two copper electrode layers with sponge bases and one honeycomb frame filled with polytetrafluoroethylene (PTFE) balls is proposed to harvest vibration energy. The application of a compact honeycomb structure increases the maximum power density of HSI‐TENG by 43.2% compared to the square grid structure and provides superior advantages in large‐scale manufacturing. More importantly, the nonspring‐assisted HSI‐TENG can generate electricity once the PTFE balls obtain sufficient kinetic energy to separate from the bottom electrode layer regardless of the vibration frequency and direction. This is fundamentally different from the spring‐assisted harvesters that can only work around their natural frequencies. The vibration model and working criteria of the HSI‐TENG are established. Furthermore, the HSI‐TENG is successfully used to serve as a self‐powered sensor to monitor engine conditions by analyzing the electrical output of the HSI‐TENG installed on a diesel engine. Therefore, the nonspring‐assisted HSI‐TENG provides a novel strategy for highly effective vibration energy harvesting and self‐powered machinery monitoring.     

50-Hz magnetic field exposure system for small animals

The design, construction, and results of evaluation of an animal-exposure system for the study of biological effects of extremely low frequency (ELF) magnetic fields are described. The system uses a square coil arrangement based on a modification of the Helmholtz coil. Due to the cubic configuration of this exposure system, horizontal and vertical magnetic fields as high as 0.3 mT can be generated. Circularly polarized magnetic fields can also be generated by changing the current and phase difference between two sets of coils. Tests were made for uniformity of the magnetic field, stray fields, sham-exposure ratio of stray field, changes of temperature and humidity, light intensity and distribution inside the animal-housing space, and noise due to air-conditioning equipment. Variation of the magnetic field was less than 2% inside the animal housing. The stray-field level inside the sham-exposure system is less than 2% of experimental exposure levels. The system can be used for simultaneous exposure of 48 rats (2 to a cage) or 96 mice (4 to a cage). © 1993 Wiley-Liss. Inc.     

Low stray ELF magnetic field exposure system for in vitro study

An exposure facility for wide application to cell exposure to an ELF (extremely low frequency) magnetic field was developed. It is suitable for conducting experiments under a high-intensity, variable-frequency magnetic field, on the biological effects of the ELF magnetic field in an in vitro study. The exposure system consists of Merritt's 4-square coil as a basic component to generate the required magnetic field intensity of 10 mT at 50 Hz with spatial field uniformity less than +/-3% in a 400 mm cube. Concentric compensation coils are adopted to eliminate the effects of stray fields on sham (control) samples in the vicinity of the exposure system. The uniformity of the magnetic field in the exposure coil, the increase in the power supply capacity due to the existence of compensation coils, and the stray field estimation were investigated carefully. After fabricating the system, performance tests were carried out and all the characteristics were found to be satisfactory. In addition, the ideal configuration for a concentric coil system was proposed.     

A Wireless Triboelectric Nanogenerator

A new “wireless” paradigm for harvesting mechanical energy via a 3D‐printed wireless triboelectric nanogenerator (W‐TENG) comprised of an ecofriendly graphene polylactic acid (gPLA) nanocomposite and Teflon is demonstrated. The W‐TENG generates very high output voltages >2 kV with a strong electric field that enables the wireless transmission of harvested energy over a distance of 3 m. The W‐TENG exhibited an instantaneous peak power up to 70 mW that could be wirelessly transmitted for storage into a capacitor obviating the need for hard‐wiring or additional circuitry. Furthermore, the use of W‐TENG for wireless and secure actuation of smart‐home applications such as smart tint windows, temperature sensors, liquid crystal displays, and security alarms either with a single or a specific user‐defined passcode of mechanical pulses (e.g., Fibonacci sequence) is demonstrated. The scalable additive manufacturing approach for gPLA‐based W‐TENGs, along with their high electrical output and unprecedented wireless applications, is poised for revolutionizing the present mechanical energy harvesting technologies.     

Tribovoltaic Effect on Metal–Semiconductor Interface for Direct‐Current Low‐Impedance Triboelectric Nanogenerators

The triboelectric nanogenerator (TENG) is a new energy technology that is enabled by coupled contact electrification and electrostatic induction. The conventional TENGs are usually based on organic polymer insulator materials, which have the limitations and disadvantages of high impedance and alternating output current. Here, a tribovoltaic effect based metal–semiconductor direct‐current triboelectric nanogenerator (MSDC‐TENG) is reported. The tribovoltaic effect is facilitated by direct voltage and current by rubbing a metal/semiconductor on another semiconductor. The frictional energy released by the forming atomic bonds excites nonequilibrium carriers, which are directionally separated to form a current under the built‐in electric field. The continuous average open‐circuit voltage (10–20 mV), short‐circuit direct‐current output (10–20 µA), and low impedance characteristic (0.55–5 kΩ) of the MSDC‐TENG can be observed during relative sliding of the metal and silicon. The working parameters are systematically studied for electric output and impedance characteristics. The results reveal that faster velocity, larger pressure, and smaller area can improve the maximum power density. The internal resistance is mainly determined by the velocity and the electrical resistance of semiconductor. This work not only expands the material candidates of TENGs from organic polymers to semiconductors, but also demonstrates a tribovoltaic effect based electric energy conversion mechanism.     

Metabolic modeling of spatial heterogeneity of biofilms in microbial fuel cells reveals substrate limitations in electrical current generation

Microbial fuel cells (MFCs) have been proposed as an alternative energy resource for the conversion of organic compounds to electricity. In an MFC, microorganisms such as Geobacter sulfurreducens form an anode‐associated biofilm that can completely oxidize organic matter (electron donor) to carbon dioxide with direct electron transfer to the anode (electron acceptor). Mathematical models are useful in analyzing biofilm processes; however, existing models rely on Nernst–Monod type expressions, and evaluate extracellular processes separated from the intracellular metabolism of the microorganism. Thus, models that combine both extracellular and intracellular components, while addressing spatial heterogeneity, are essential for improved representation of biofilm processes. The goal of this work is to develop a model that integrates genome‐scale metabolic models with the model of biofilm environment. This integrated model shows the variations of electrical current production and biofilm thickness under the presence/absence of NH₄ in the bulk solution, and under varying maintenance energy demands. Further, sensitivity analysis suggested that conductivity is not limiting electrical current generation and that increasing cell density can lead to enhanced current generation. In addition, the modeling results also highlight instances such as the transformation into respiring cells, where the mechanism of electrical current generation during biofilm development is not yet clearly understood.     

Toward a Carbon Dioxide Neutral Industrial Park

The industrial park of Herdersbrug (Brugge, Flanders, Belgium) comprises 92 small and medium‐sized enterprises, a waste‐to‐energy incinerator, and a power plant (not included in the study) on its site. To study the carbon dioxide (CO₂) neutrality of the park, we made a park‐wide inventory for 2007 of the CO₂ emissions due to energy consumption (electricity and fossil fuel) and waste incineration, as well as an inventory of the existing renewable electricity and heat generation. The definition of CO₂ neutrality in Flanders only considers CO₂ released as a consequence of consumption or generation of electricity, not the CO₂ emitted when fossil fuel is consumed for heat generation. To further decrease or avoid CO₂ emissions, we project and evaluate measures to increase renewable energy generation. The 21 kilotons (kt) of CO₂ emitted due to electricity consumption are more than compensated by the 25 kt of CO₂ avoided by generation of renewable electricity. Herdersbrug Industrial Park is thus CO₂ neutral, according to the definition of the Flemish government. Only a small fraction (6.6%) of the CO₂ emitted as a consequence of fossil fuel consumption (heat generation) and waste incineration is compensated by existing and projected measures for renewable heat generation. Of the total CO₂ emission (149 kt) due to energy consumption (electricity + heat generation) and waste incineration on the Herdersbrug Industrial Park in 2007, 70.5% is compensated by existing and projected renewable energy generated in the park. Forty‐seven percent of the yearly avoided CO₂ corresponds to renewable energy generated from waste incineration and biomass fermentation.