Technical difficulties and solutions of direct transesterification process of microbial oil for biodiesel synthesis

Microbial oils are considered as alternative to vegetable oils or animal fats as biodiesel feedstock. Microalgae and oleaginous yeast are the main candidates of microbial oil producers’ community. However, biodiesel synthesis from these sources is associated with high cost and process complexity. The traditional transesterification method includes several steps such as biomass drying, cell disruption, oil extraction and solvent recovery. Therefore, direct transesterification or in situ transesterification, which combines all the steps in a single reactor, has been suggested to make the process cost effective. Nevertheless, the process is not applicable for large-scale biodiesel production having some difficulties such as high water content of biomass that makes the reaction rate slower and hurdles of cell disruption makes the efficiency of oil extraction lower. Additionally, it requires high heating energy in the solvent extraction and recovery stage. To resolve these difficulties, this review suggests the application of antimicrobial peptides and high electric fields to foster the microbial cell wall disruption.     

Optimization of direct conversion of wet algae to biodiesel under supercritical methanol conditions

This study demonstrated a one-step process for direct liquefaction and conversion of wet algal biomass containing about 90% of water to biodiesel under supercritical methanol conditions. This one-step process enables simultaneous extraction and transesterification of wet algal biomass. The process conditions are milder than those required for pyrolysis and prevent the formation of by-products. In the proposed process, fatty acid methyl esters (FAMEs) can be produced from polar phospholipids, free fatty acids, and triglycerides. A response surface methodology (RSM) was used to analyze the influence of the three process variables, namely, the wet algae to methanol (wt./vol.) ratio, the reaction temperature, and the reaction time, on the FAMEs conversion. Algal biodiesel samples were analyzed by ATR-FTIR and GC-MS. Based on the experimental analysis and RSM study, optimal conditions for this process are reported as: wet algae to methanol (wt./vol.) ratio of around 1:9, reaction temperature and time of about 255 °C, and 25 min respectively. This single-step process can potentially be an energy efficient and economical route for algal biodiesel production.     

Direct preparation of biodiesel from rapeseed oil leached by two-phase solvent extraction

A new method which coupled the two-phase solvent extraction (TSE) with the synthesis of biodiesel was studied. Investigations were carried out on transesterification of methanol with oil-hexane solution coming from TSE process in the presence of sodium hydroxide as the catalyst. Biodiesel (fatty acid methyl esters) were the products of transesterification. The influential factors of transesterification, such as reaction time, catalyst concentration, mole ratio of methanol to oil and reaction temperature were optimized. The results showed that the optimal reaction parameters were sodium hydroxide concentration 1.1% by weight of rapeseed oil, mole ratio of methanol to oil 9:1, reaction time 120 min, and reaction temperature 55-60 degrees C. Under these conditions, the TG conversion would rise up to 98.2%. Based on the new method, biodiesel production process could be simplified and the biodiesel cost could be reduced.     

Zero-waste biorefinery of oleaginous microalgae as promising sources of biofuels and biochemicals through direct transesterification and acid hydrolysis

Oleaginous microalgae are considered as promising sources of biofuels and biochemicals due to their high lipid content and other high-value components such as pigments, carbohydrate and protein. This study aimed to develop an efficient biorefinery process for utilizing all of the components in oleaginous microalgae. Acetone extraction was used to recover microalgal pigments prior to processes for the other products. Microalgal lipids were converted into biodiesel (fatty acid methyl ester, FAME) through a conventional two-step process of lipid extraction followed by transesterification, and alternatively a one-step direct transesterification. The comparable FAME yields from both methods indicate the effectiveness of direct transesterification. The operating parameters for direct transesterification were optimized through response surface methodology (RSM). The maximum FAME yield of 256 g/kg-biomass was achieved when using chloroform:methanol as co-solvents for extracting and reacting reagents at 1.35:1 volumetric ratio, 70 °C reaction temperature, and 120 min reaction time. The carbohydrate content in lipid-free microalgal biomass residues (LMBRs) was subsequently acid hydrolyzed into sugars under optimized conditions from RSM. The maximum sugar yield obtained was 44.8 g/kg-LMBRs and the protein residues were recovered after hydrolysis. This biorefinery process may contribute greatly to zero-waste industrialization of microalgae based biofuels and biochemicals.     

Optimization of microwave-assisted transesterification of dry algal biomass using response surface methodology

The effect of microwave irradiation on the simultaneous extraction and transesterification (in situ transesterification) of dry algal biomass to biodiesel was investigated. A high degree of oil/lipid extraction from dry algal biomass and an efficient conversion of the oils/lipids to biodiesel were demonstrated in a set of well-designed experimental runs. A response surface methodology (RSM) was used to analyze the influence of the process variables (dry algae to methanol (wt/vol) ratio, catalyst concentration, and reaction time) on the fatty acid methyl ester conversion. Based on the experimental results and RSM analysis, the optimal conditions for this process were determined as: dry algae to methanol (wt/vol) ratio of around 1:12, catalyst concentration about 2 wt.%, and reaction time of 4 min. The algal biodiesel samples were analyzed with GC-MS and thin layer chromatography (TLC) methods. Transmission electron microscopy (TEM) images of the algal biomass samples before and after the extraction/transesterification reaction are also presented.     

Biodiesel production by simultaneous extraction and conversion of total lipids from microalgae, cyanobacteria, and wild mixed-cultures

Microalgae have been identified as a potential biodiesel feedstock due to their high lipid productivity and potential for cultivation on marginal land. One of the challenges in utilizing microalgae to make biodiesel is the complexities of extracting the lipids using organic solvents followed by transesterification of the extracts to biodiesel. In the present work, reaction conditions were optimized that allow a single step extraction and conversion to biodiesel in high yield from microalgae. From the optimized conditions, it is demonstrated that quantitative conversion of triglycerides from several different microalgae and cyanobacteria could be achieved, including from mixed microbial biomass collected from a municipal wastewater lagoon. Evidence is presented that for some samples, significantly more biodiesel can be produced than would be expected from available triglycerides, indicating conversion of fatty acids contained in other molecules (e.g., phospholipids) using this approach. The effectiveness of the approach on wet algae is also reported.     

Prospects for microbial biodiesel production

As the demand for biofuels for transportation is increasing, it is necessary to develop technologies that will allow for low-cost production of biodiesel. Conventional biodiesel is mainly produced from vegetable oil by chemical transesterification. This production, however, has relatively low land-yield and is competing for agricultural land that can be used for food production. Therefore, there is an increasing interest in developing microbial fermentation processes for production of biodiesel as this will allow for the use of a wide range of raw-materials, including sugar cane, corn, and biomass. Production of biodiesel by microbial fermentation can be divided into two different approaches, (1) indirect biodiesel production from oleaginous microbes by in vitro transesterification, and (2) direct biodiesel production from redesigned cell factories. This work reviews both microbial approaches for renewable biodiesel production and evaluates the existing challenges in these two strategies.     

An overview of enzymatic production of biodiesel

Biodiesel production has received considerable attention in the recent past as a biodegradable and nonpolluting fuel. The production of biodiesel by transesterification process employing alkali catalyst has been industrially accepted for its high conversion and reaction rates. Recently, enzymatic transesterification has attracted much attention for biodiesel production as it produces high purity product and enables easy separation from the byproduct, glycerol. But the cost of enzyme remains a barrier for its industrial implementation. In order to increase the cost effectiveness of the process, the enzyme (both intracellular and extracellular) is reused by immobilizing in a suitable biomass support particle and that has resulted in considerable increase in efficiency. But the activity of immobilized enzyme is inhibited by methanol and glycerol which are present in the reacting mixture. The use of tert-butanol as solvent, continuous removal of glycerol, stepwise addition of methanol are found to reduce the inhibitory effects thereby increasing the cost effectiveness of the process. The present review analyzes these methods reported in literature and also suggests a suitable method for commercialization of the enzymatic process.     

Ethanesulfonic acid-based esterification of industrial acidic crude palm oil for biodiesel production

An industrial grade acidic crude palm oil (ACPO) pre-treatment process was carried out using ethanesulfonic acid (ESA) as a catalyst in the esterification reaction. ESA was used in different dosages to reduce free fatty acid (FFA) to a minimum level for the second stage of biodiesel production via alkaline transesterification reaction. Different process operating conditions were optimized such as ESA dosage (0.25-3.5% wt/wt), methanol to ACPO molar ratio (1:1-20:1), reaction temperature (40-70 °C), and reaction time (3-150 min). This study revealed the potential use of abundant quantities of ACPO from oil palm mills for biodiesel production. The lab scale results showed the effectiveness of the pre-treatment process using ESA catalyst. Three consecutive catalyst recycling runs were achieved without significant degradation in its performance. Second and third reuse runs needed more reaction time to achieve the target level of FFA content. Esterification and transesterification using ESA and KOH respectively is proposed for biodiesel industrial scale production. The produced biodiesel meets the international standards specifications for biodiesel fuel (EN 14214 and ASTM D6751).     

Evaluation of extraction methods for recovery of fatty acids from lipid-producing microheterotrophs

The effect of different extraction techniques on the recovery of fatty acids from freeze-dried biomass of two lipid-producing microheterotrophs was examined. Two procedures were used: the extraction of lipids from biomass followed by transesterification of the fatty acids (extraction-transesterification); and the direct transesterification of biomass to produce fatty acid methyl esters (i.e. without the initial extraction step). Variable factors in the extraction-transesterification experiment were the sequence in which solvents were added to the samples, the relative amount of methanol in the solvent mix, and sonication of biomass while in the solvent mix. Variable factors in the direct transesterification experiment were sample size, and reaction duration. Statistical analysis of data (level of significance P<0.05) showed that: (1) extraction of total fatty acids prior to transesterification was significantly more efficient when solvents were added in the order of increasing polarity; (2) neither sonication nor increasing the proportion of methanol in the extraction solvent significantly affected extraction of fatty acids prior to transesterification; (3) efficiency of direct transesterification of fatty acids increased significantly with reaction time; (4) efficiency of direct transesterification of fatty acids was not significantly affected by sample size; (5) the most efficient method for extraction of fatty acids prior to transesterification yielded significantly less fatty acids than the most effective direct transesterification method. While the study examined only two strains, our results suggest that fatty acid analysis methodology for microheterotrophs under consideration for biotechnological exploitation requires optimisation and validation.     

Biodiesel production by supercritical process with crude bio-methanol prepared by wood gasification

In order to prepare a genuine biodiesel, it is essential to use methanol prepared from biomass but not natural gas for biodiesel production. Thus, we have proposed to use crude bio-methanol produced by wood gasification for biodiesel production. Since such a bio-methanol contains some impurities, an effect of its impurities was studied on the biodiesel production by supercritical method. In general, impurities in crude bio-methanol are reported to include methyl formate, ethanol, 1-butanol, diisopropyl ether, water, etc. Triglycerides and oleic acids were, thus, treated with these impurities under supercritical conditions. As a result, it was found that methyl formate, ethanol and 1-butanol could convert them to fatty acid alkyl esters (BDF), whereas no conversion was achieved with diisopropyl ether. Thus, crude bio-methanol can be used for BDF production as a substitute for methanol from fossil resources. However, due to more efficient reaction, crude bio-methanol can be more applicable to the two-step supercritical methanol process, consisting of hydrolysis of triglycerides and subsequent esterification of fatty acids, compared with the one-step supercritical methanol process, where transesterification of triglycerides is a major reaction.     

Esterification using a liquid lipase to remove residual free fatty acids in biodiesel

Lately, the price of liquid formulated lipase enzymes, usable in biodiesel production, has been significantly reduced. This enables one-time use of these enzymes for transesterification, and the process is used industrially. However, the process suffers a drawback by leaving 2−3 % free fatty acids in the crude biodiesel, which reduces the profitability. This article discusses a novel enzymatic FFA esterification reaction utilizing liquid lipase B from Candida antarctica (CALB) along with glycerol at low water concentrations to eliminate the residual FFA. The reaction setup was found able to reduce the free fatty acid concentration to within biodiesel specifications of < 0.25 wt.% FFA. Additionally, two alternative process setups are proposed, which were both found viable through a combination of experiments and simulations, and can be developed into full-scale processes. The resulting two-step enzymatic biodiesel process - transesterification followed by esterification - provides a potential process layout for the industrial production of biodiesel.     

Process integration possibilities for biodiesel production from palm oil using ethanol obtained from lignocellulosic residues of oil palm industry

In this paper, integration possibilities for production of biodiesel and bioethanol using a single source of biomass as a feedstock (oil palm) were explored through process simulation. The oil extracted from Fresh Fruit Bunches was considered as the feedstock for biodiesel production. An extractive reaction process is proposed for transesterification reaction using in situ produced ethanol, which is obtained from two types of lignocellulosic residues of palm industry (Empty Fruit Bunches and Palm Press Fiber). Several ways of integration were analyzed. The integration of material flows between ethanol and biodiesel production lines allowed a reduction in unit energy costs down to 3.4%, whereas the material and energy integration leaded to 39.8% decrease of those costs. The proposed integrated configuration is an important option when the technology for ethanol production from biomass reaches such a degree of maturity that its production costs be comparable with those of grain or cane ethanol.     

Efficient solvothermal wet in situ transesterification of Nannochloropsis gaditana for biodiesel production

In situ transesterification of wet microalgae is a promising, simplified alternative biodiesel production process that replaces multiple operations of cell drying, extraction, and transesterification reaction. This study addresses enhanced biodiesel production from Nannochloropsis gaditana at elevated temperatures. Compared with the previously reported in situ transesterification process of conducting the reaction at a temperature ranging from 95 to 125 °C, the present work employs higher temperatures of at least 150 °C. This relatively harsh condition allows much less acid catalyst with or without co-solvent to be used during this single extraction-conversion process. Without any co-solvent, 0.58% (v/v) of H₂SO₄ in the reaction medium can achieve 90 wt% of the total lipid conversion to biodiesel at 170 °C when the moisture content of wet algal paste is 80 wt%. Here, the effects of temperature, acid catalyst, and co-solvent on the FAEE yield and specification were scrutinized, and the reaction kinetic was investigated to understand the solvothermal in situ transesterification reaction at the high temperature. Having a biphasic system (water/chloroform) during the reaction also helped to meet biodiesel quality standard EN 14214, as Na⁺, K⁺, Ca²⁺, Mg²⁺ cations and phosphorus were detected only below 5 ppm. With highlights on the economic feasibility, wet in situ transesterification at the high temperature can contribute to sustainable production of biodiesel from microalgae by reducing the chemical input and relieve the burden of extensive post purification process, therefore a step towards green process.

     

Energy recovery from lipid extracted,transesterified and glycerol codigested microalgae biomass

The production of methane (CH₄) via the anaerobic digestion of microalgae biomass residues from the biodiesel production process has the potential to meet some of the energy requirements of the primary biomass to fuel conversion process. This paper investigates the practical CH₄ yields achievable from the anaerobic conversion of the microalgae residues (as well as codigestion with glycerol) after biodiesel production using both the conventional and in situ transesterification methods. Results demonstrate that the type of lipid extraction solvent utilized in the conventional transesterification process could inhibit subsequent CH₄ production. On the basis of actual CH₄ production, a recoverable energy of 8.7–10.5 MJ kg^?1 of dry microalgae biomass residue was obtained using the lipid extracted and transesterified microalgae samples. On codigesting the microalgae residues with glycerol, a 4–7% increase in CH₄ production was observed.     

Biodiesel production with special emphasis on lipase-catalyzed transesterification

The production of biodiesel by transesterification employing acid or base catalyst has been industrially accepted for its high conversion and reaction rates. Downstream processing costs and environmental problems associated with biodiesel production and byproducts recovery have led to the search for alternative production methods. Recently, enzymatic transesterification involving lipases has attracted attention for biodiesel production as it produces high purity product and enables easy separation from the byproduct, glycerol. The use of immobilized lipases and immobilized whole cells may lower the overall cost, while presenting less downstream processing problems, to biodiesel production. The present review gives an overview on biodiesel production technology and analyzes the factors/methods of enzymatic approach reported in the literature and also suggests suitable method on the basis of evidence for industrial production of biodiesel.     

Biodiesel production from isolated oleaginous fungi Aspergillus sp. using corncob waste liquor as a substrate

The study documented the potential of isolated filamentous fungus Aspergillus sp. as whole cell biocatalyst for biodiesel production using Sabourauds dextrose broth medium (SDBM) and corncob waste liquor (CWL) as substrates. SDBM showed improvement in both biomass production (13.6 g dry weight/1000 ml) and lipid productivity (23.3%) with time. Lipid extraction was performed by direct (DTE) and indirect (IDTE) transesterification methods. DTE showed higher transesterification efficiency with broad spectrum of fatty acids profile over IDTE. CWL as substrate showed good lipid productivity (22.1%; 2g dry biomass; 48 h) along with efficient substrate degradation. Lipids derived from both substrates depicted high fraction of saturated fatty acids than unsaturated ones. Physical characteristics of fungal based biodiesel correlated well with prescribed standards. CWL derived biodiesel showed relatively good fuel properties (acid number, 0.40 mg KOH/g of acid; iodine value, 11 g I?/100 g oil; density, 0.8342 g/cm3) than SDBM derived biodiesel.     

An overview on the recent advances in the transesterification of vegetable oils for biodiesel production using chemical and biocatalysts

Biodiesel, chemically defined as monoalkyl esters of long chain fatty acids, are derived from renewable feed stocks like vegetable oils and animal fats. It is produced by both batch and continuous transesterification processes in which, oil or fat is reacted with a monohydric alcohol in the presence of a catalyst. The conventional method of producing biodiesel involves acid and base catalysts to form fatty acid alkyl esters. Downstream processing costs and environmental problems associated with biodiesel production and byproducts recovery have led to the search for alternative production methods and alternative substrates. Enzymatic reactions involving lipases can be an excellent alternative to produce biodiesel through a process commonly referred to as alcoholysis, a form of transesterification reaction or through an interesterification reaction. In order to increase the cost effectiveness of the process, the enzymes are immobilized using a suitable matrix. The use of immobilized lipases and whole cells may lower the overall cost, while presenting less downstream processing problems. Main focus of this paper is to discuss the important parameters that affect the biodiesel yield, various immobilization techniques employed, mechanisms and kinetics of transesterification reaction and the recent advances in continuous transesterification processes.     

Whole-cell biocatalysts for biodiesel fuel production

Biodiesel fuel (BDF), which refers to fatty acid alkyl esters, has attracted considerable attention as an environmentally friendly alternative fuel for diesel engines. Alkali catalysis is widely applied for the commercial production of BDF. However, enzymatic transesterification offers considerable advantages, including reducing process operations in biodiesel fuel production and an easy separation of the glycerol byproduct. The high cost of the lipase enzyme is the main obstacle for a commercially feasible enzymatic production of biodiesel fuels. To reduce enzyme associated process costs, the immobilization of fungal mycelium within biomass support particles (BSPs) as well as expression of the lipase enzyme on the surface of yeast cells has been developed to generate whole-cell biocatalysts for industrial applications.     

Biodiesel production through lipase catalyzed transesterification: An overview

Recently, with the global shortage of fossil fuels, excessive increase in the price of crude oil and increased environmental concerns have resulted in the rapid growth in biodiesel production. The central reaction in the biodiesel production is the transesterification reaction which could be catalyzed either chemically or enzymatically. Enzymatic transesterification has certain advantages over the chemical catalysis of transesterification, as it is less energy intensive, allows easy recovery of glycerol and the transesterification of glycerides with high free fatty acid contents. Limitations of the enzyme catalyzed reactions include high cost of enzyme, low yield, high reaction time and the amount of water and organic solvents in the reaction mixture. Researchers have been trying to overcome these limitations in the enzyme catalyzed transesterification reaction. This paper is meant to review the latest development in the field of lipase catalyzed transesterification of biologically derived oil to produce biodiesel.