Resolution of isomers of sorbitolparaben esters by chromatographic and electrophoretic techniques

Pharmaceutical preparations usually contain preservatives and sweeteners. When parabens are used as preservatives and a polyol as a sweetener, a transesterification reaction may happen, yielding the transester polyol-paraben. The products formed in the transesterification reaction of methylparaben and sorbitol were analyzed by micellar electrokinetic chromatography and by HPLC. Up to six positional isomers of sorbitolparaben (SPB) can be produced. However, only three peaks were found by HPLC. The higher efficiency and resolution power of MEKC allowed one to resolve five peaks. Results were compared with those obtained by capillary zone electrophoresis in borate buffer, where the separation of isomers occurred in a different way, because of a complexation between SPB and borate.     

Two-dimensional mapping of N-glycosidically linked asialo-oligosaccharides from glycoproteins as reductively pyridylaminated derivatives using dual separation modes of high-performance capillary electrophoresis.

N-Glycosidically linked oligosaccharides were released from glycoproteins by digestion with trypsin followed by hydrazinolysis and subsequently re-N-acetylated and reductively pyridylaminated. Derivatives of sialic acid-containing oligosaccharides were further desialylated with neuraminidase. The final derivatives of asialo-oligosaccharides were analyzed by capillary zone electrophoresis in two carriers, an acidic phosphate buffer and an alkaline borate buffer. The former carrier allowed direct zone electrophoresis as cationic immonium ions, accordingly size-dependent separation, whereas the latter realized indirect electrophoresis as anionic borate complexes, i.e., separation based on the structural variation in outermost monosaccharide residues. Two-dimensional plots of relative mobilities of the derivatives in these dual separation modes to reductively pyridylaminated glucose provided a good tool for identification of oligosaccharides.     

Analysis of the oligosaccharides in ovalbumin by high-performance capillary electrophoresis

The oligosaccharides in ovalbumin as a glycoprotein model were released with anhydrous hydrazine, and reductively pyridylaminated after re-N-acetylation. The derivatives were analyzed by capillary zone electrophoresis (CZE) with on-column fluorometric detection. Direct CZE could separate the derivatives on the basis of the degree of polymerization, giving five peaks of hepta-, octa-, nona-, deca-, and undecasaccharides. Coelectrophoresis with the standard mixture of isomaltooligosaccharide derivatives was effective for peak assignment. CZE as borate complexes allowed separation on the basis of structural difference, especially in the peripheral monosaccharide residues. Peaks were tentatively assigned to the derivatives of reported oligosaccharides by comparing their relative mobilities with those of the chromatographic fractions obtained by using the ODS and Dowex 50W x 2 columns. These two modes gave excellent separation and were complementary to each other. Although the actual amount analyzed in the capillary tube was quite small (ca. 5 ng as carbohydrates), a larger amount (ca. 25 micrograms as carbohydrates) was required to make sample concentration sufficiently high to be detected by a modification of a commercial fluoromonitor for HPLC.     

Separation and detection of closely related peptides by micellar electrokinetic chromatography coupled with electrospray ionization mass spectrometry using the partial filling technique

Closely related peptides such as neurotensin and angiotensin analogues were separated by capillary zone electrophoresis using a nonionic surfactant, sucrose monododecanoate, as a micelle forming reagent. These peptides were detected by an on-line coupled mass spectrometer using an electrospray ionization interface. However, the presence of the micelles in the separation solution drastically reduced the sensitivity of the mass spectrometer. Therefore, a partial filling technique was employed to prevent the micelles from entering the mass spectrometric interface. A part of the capillary from the injection end was filled with the micellar solution in this technique. Analytes passed through the micellar zone during the electrophoresis and when the separated analytes reached the detection end of the capillary, the micellar zone was still behind the analyte zones, because the nonionic surfactant moved very slowly in acidic conditions. Thus the technique was very useful for mass spectrometric detection for CE when the micellar solution was employed for separation. The optimization of separation and detection conditions was investigated.     

Determination of amino acids in saliva using capillary electrophoresis with fluorimetric detection

In the present study a sensitive method for the quantification of main free amino acids in saliva using capillary electrophoresis with laser induced fluorescence detection was developed. As background electrolyte 20 mM borate buffer pH 9.5 was used. Amino acids were separated after derivatization with fluorescein isothiocyanate (FITC) and the conditions for derivatization were optimized. The main amino acids occurring in saliva (Pro, Ser, Gly and Glu) were separated in less than 7 min. The parameters of validation such as linearity of response, precision and detection limits were determined. The detection limits were obtained in the range from 0.1 to 2.4 nM. The developed method was employed for determination of amino acids in real saliva samples.     

Cysteine Racemization in Peptide Synthesis: A New and Easy Detection Method

A new method has been developed for the rapid determination of D-cysteine contents in synthetic peptides. It is based on the reduction of cystine residues, when present, with tris- alkylphosphines, selective derivatization of the cysteine residues with 4-vinylpyridine, followed by acid hydrolysis of the (4-pyridylethyl)cysteine –peptides. Baseline enantiomeric resolution of theD ,L -S-β-(4-pyridylethyl)cysteine, and thus quantification ofD - enantiomer contents at levels ≤1%, is easily achieved by capillary zone electrophoresis exploiting the host–guest complexation principle with crown ethers or by gas chromatography on chiral glass capillary columns upon conventional derivatization of the hydrolysate. The acid-stability of the (4-pyridylethyl)cysteine derivative prevents racemization via thiazoline intermediates and allows for standardization of the acid hydrolysis-dependent racemization.     

Positional isomers of sulfated oligosaccharides obtained from agarans and carrageenans: preparation and capillary electrophoresis separation

Partial reductive hydrolysis was used to produce oligosaccharide alditols from repetitive sulfated galactans obtained from four Rhodophyta species: kappa-carrageenan (from Kappaphycus alvarezii), theta-carrageenan (Gigartina skottsbergii-alkali-treated lambda-carrageenan), agarose 6-sulfate (Gracilaria domingensis), and pyruvylated agarose 2-sulfate (Acanthophora spicifera-alkali-treated pyruvylated agaran sulfate). Each hydrolyzate was submitted to anion-exchange and gel-filtration chromatography, and the isolated oligosaccharide alditols were identified by 1D and 2D NMR spectroscopy and by ESI mass spectrometry. The positional isomers of the sulfated oligosaccharide alditols were then completely resolved by capillary electrophoresis in a borate buffer. Attempts to correlate the availability of the hydroxyl groups for borate complexation with the relative migration of the oligosaccharides are presented.     

Rapid and sensitive analyses of glycoprotein-derived oligosaccharides by liquid chromatography and laser-induced fluorometric detection capillary electrophoresis

Asparagine-type oligosaccharides are released from core proteins as N-glycosylamines in the initial step of the action of the peptide N(4)-(N-acetyl-β-D-glucosaminyl)asparagine amidase F (PNGase F). The released N-glycosylamine-type oligosaccharides (which are exclusively present at least during the course of the enzyme reaction) could therefore be derivatized with amine-labeling reagents. Here we report a method using 4-fluoro-7-nitro-2,1,3-benzoxadiazole (NBD-F) as a labeling reagent for glycosylamine-type oligosaccharides. We applied the method for the sensitive analysis of some oligosaccharide mixtures derived from well-characterized glycoproteins including human transferrin, α(1)-acid glycoprotein, bovine fetuin, and ribonuclease B. NBD-labeled oligosaccharides were successfully separated on an amide-bonded column or a diol-silica column. This labeling method included the release of oligosaccharides from glycoproteins and derivatization of oligosaccharides in a one-pot reaction and was completed within 3h. The method showed approximately fivefold higher sensitivity than that involving labeling with ethyl p-aminobenzoate (ABEE) in HPLC using fluorometric detection and a one order of magnitude higher response in ESI-LC/MS. We also applied this method for the sensitive analysis of glycoprotein-derived oligosaccharides by capillary electrophoresis with laser-induced fluorometric detection (LIF-CE). The limit of detection in HPLC and LIF-CE were 100fmol and 4fmol, respectively.     

Determination of octopamine in human plasma by capillary electrophoresis with optical fiber light-emitting diode-induced fluorescence detection

A new analytical method based on capillary electrophoresis (CE) separation and optical fiber light-emitting diode (LED)-induced fluorescence detection has been developed for the determination of octopamine. Naphthalene-2,3-dicarboxaldehyde (NDA) was used for precolumn derivatization of octopamine. The separation and determination of the derivative was performed using a laboratory-built CE system with an optical fiber LED-induced fluorescence detector. Optimal separation was obtained at 20 kV using a background electrolyte solution consisting of 25 mM sodium borate (pH 9.2). High sensitivity detection was achieved by the optical fiber LED-induced fluorescence detection using a purple LED as the excitation source. The limit of detection (signal/noise=3) for octopamine was 5.0 x 10(-9)M. A calibration curve ranging from 1.0 x 10(-8) to 5.0 x 10(-7)M was shown to be linear. Using this method, the levels of octopamine in human plasma from healthy donors were determined.     

Determination of amino acids in saliva using capillary electrophoresis with fluorimetric detection

In the present study a sensitive method for the quantification of main free amino acids in saliva using capillary electrophoresis with laser induced fluorescence detection was developed. As background electrolyte 20 mM borate buffer pH 9.5 was used. Amino acids were separated after derivatization were optimized. The main amino acids occurring in saliva (Pro, Ser, Gly and Glu) were separated in less than 7 min. The parameters of validation such as linearity of response, precision and detection limits were determined. The detection limits were obtained in the range from 0.1 to 2.4 nM. The developed method was employed for determination of amino acids in real saliva samples.     

Determination of poorly separated monoclonal serum proteins by capillary zone electrophoresis

A capillary zone electrophoresis (CZE) technique was developed for the determination of poorly separated monoclonal serum proteins by agarose gel electrophoresis (AGE). A P/ACE 5500 capillary instrument (Beckman) was used under the following conditions: 57 cm x 50 microm I.D. fused-silica capillary, pH 9.6 borate buffer, and 214 nm on-line detection. Sixty patients (61 +/- 13 years) with a well isolated (n=24, group A) or poorly separated monoclonal band(s) by AGE (n=36, group B) were included in this study. Within- and between-run precision for CZE was below 4% for albumin and 7% for gamma-globulin. A 100% (group A) or 61% agreement (group B, more bands detected by CZE in 10 cases) was obtained between CZE and AGE for the number of monoclonal bands. In group B, quantification was possible in 92% of samples by CZE vs. 64% by AGE (P<0.05, chi-square). The proposed CZE method appears as an additional helpful technique for the determination of poorly separated monoclonal serum proteins by AGE.     

Separation and determination of peptide hormones by capillary electrophoresis with laser-induced fluorescence coupled with transient pseudo-isotachophoresis preconcentration

A new method for the determination of the peptide hormones and their fragments by capillary electrophoresis (CE) with laser-induced fluorescence (LIF) detection and transient pseudo-isotachophoresis (pseudo-tITP) preconcentration was established in this study. The LIF detector used an argon ion laser with excitation wavelength at 488 nm and emission wavelength at 535 nm. Fluorescein isothiocyanate (FITC) was used as precolumn derivatization reagent to label cholecystokinin tetrapeptide (CCK-4), neurotensin (NT), neurotensin hexapeptide (NT_8–13), and neurokinin B (NKB). Borate (10 mmol/L, pH 9.0) was selected as derivatization medium to get the high efficiency. When the addition of 70% (v/v) methanol and 1% (m/v) sodium chloride (NaCl) to the sample matrix, and with borate buffer (110 mM, pH 9.5) and 20% (v/v) methanol as running buffer, a preconcentration based on the pseudo-tITP afforded 100-fold improvement in peak heights compared with the traditional hydrodynamic injection (2.3% capillary volume). The detection limits (signal/noise = 3) based on peak height were found to be 0.04, 0.1, 0.2, and 0.08 nmol/L for NT_8–13, NT, NKB, and CCK-4, respectively. The method was validated and applied to qualitative analysis of NT and NT_8–13 in human cerebrospinal fluid sample.     

Capillary electromigration methods for the study of collagen

This review paper gives an overview of capillary electromigration methods used in the analysis of collagen. Analyses of the parent chains as well as of the bromcyane and collagenase fragments of collagens are presented. Methods include capillary zone electrophoresis, capillary gel electrophoresis, micellar electrokinetic chromatography as well as combinations of HPLC and capillary electrophoresis, and capillary electrophoresis with mass spectrometry.     

High-performance separation methods in the analysis of a new peptide family: the galanins

An analytical investigation of a new peptide family, the human galanins and their fragments, was carried out by reversed-phase HPLC, capillary zone electrophoresis (CZE) at different pH values and micellar electrokinetic capillary chromatography (MECC) in phosphate-borate-sodium dodecyl sulphate buffer. None of the methods seems to be superior to the others. The complementary nature of the electrophoretic methods is obvious when the profiles of peptides are compared; impurities not separated by HPLC are separated by CZE or MECC and vice versa. With these three different separation methods, a more complex analytical control of the synthetic work can be achieved.     

Simultaneous determination of phthalate di- and monoesters in poly(vinylchloride) products and human saliva by gas chromatography-mass spectrometry

This paper reports on the selectivity behaviour of tryptic peptides on a Cu(2+)-loaded immobilised metal ion affinity chromatography (IMAC) support. Ovalbumin was chosen as a model protein for investigation of the selection and separation of histidine-containing peptides by IMAC off-line coupled with capillary electrophoresis and matrix-assisted laser desorption ionisation time-of-flight mass spectrometry (MALDI-TOF). Two of five histidine-containing peptides in addition to some non-histidine-containing peptides from a tryptic digest of ovalbumin were captured by IMAC. To separate and purify the selected peptides, the IMAC sample was analysed by capillary zone electrophoresis (CZE). The sample was not separated by capillary zone electrophoresis, therefore, micellar electrokinetic chromatography (MEKC) using 10-75 mM SDS was used. Analysis of IMAC sample by MEKC, using low concentrations of SDS (10 mM) was characterised by MALDI-TOF. When using SDS at 75 mM, the migration times of reversed-phase fractions of the IMAC sample, were used to identify the peaks. One of the two selected histidine-containing peptides with two histidine residues was identified, analysing the sample by CZE or MEKC.     

Plasma D-penicillamine redox state evaluation by capillary electrophoresis with laser-induced fluorescence

D-Penicillamine (D-Pen) is a thiol drug used in the treatment of Wilson's disease, rheumatoid arthritis, metal intoxication and cystinuria. We have recently described a new capillary electrophoresis (CE) method to measure physiological thiols, in which separation of total plasma homocysteine, cysteine, cysteinylglycine, glutathione is achieved using the organic base N-methyl-D-glucamine in the run buffer. In this paper, we present an improvement of our method that allows a baseline separation of total plasma D-Pen from the physiological thiols. Moreover, reduced, free and protein-bound forms of drug are measured by varying the order of disulfide reduction with tributylphosphine and proteins precipitation with 5-sulphosalicylic acid (SSA). After derivatization with 5-iodoacetamidofluorescein (5-IAF), samples are separated and measured by capillary electrophoresis with laser-induced fluorescence in an uncoated fused-silica capillary (57 x 75 microm i.d.) using a phosphate/borate run buffer pH 11.4. In these conditions, the migration time of D-Pen is about 7 min and the time required for each analysis is roughly 10 min. The proposed method has been utilized to measure the various forms of the drug in a D-Pen administered Wilson's disease patient.     

Determination of 1-phenyl-3-methyl-5-pyrazolone-labeled carbohydrates by liquid chromatography and micellar electrokinetic chromatography

In this paper, the method for the derivatization of carbohydrates with 1-phenyl-3-methyl-5-pyrazolone (PMP) was simplified. One-third of the derivatization time was saved. Five monosaccharide derivatives have been well separated by MEKC and HPLC under optimized conditions. Good reproducibility could be obtained with relative standard deviation (RSD) values of the migration times within 5.0 and 2.3%, respectively. Furthermore, the developed methods have been successfully applied to the analysis of carbohydrates in Aloe powder and food. These methods are quite useful for routine analysis of monosaccharides and oligosaccharides in real samples.     

Size-exclusion liquid chromatography and capillary electrophoresis of pollen allergens

Allergens from the pollen of Phleum pratense, Dactylis glomerata. Arrhenatherum elatius, Secale cereale, Lolium perrene and Festuca sp. were analysed by size-exclusion chromatography (SEC) and capillary electrophoresis (CE). SEC was used for the determination of the molecular masses of main allergens. A CE method, using either 150 mmol/1 phosphoric acid (pH 1.8) or a micellar system consisting of 50 mmol/l sodium dodecyl sulphate-20 mmol/l borate (pH 9.35), was developed as a rapid and efficient alternative to SEC, especially for process control of allergenic preparations. The results obtained by the two methods confirmed similarities in the structures of the studied pollen allergens.     

Determination of dimethylamine and other low-molecular-mass amines using capillary electrophoresis with laser-induced fluorescence detection

The potential of capillary electrophoresis (CE) with laser-induced fluorescence (LIF) detection for the separation and determination of dimethylamine (DMA) and other low-molecular-mass amines involving precolumn derivatization with fluorescein isothiocyanate isomer I (FITC) was investigated. Different variables that affect derivatization (pH, FITC concentration, reaction time and temperature) and separation (buffer concentration, addition of various organic modifiers, applied voltage and length of capillary) were studied. The linearity, reproducibility and reliability of the method were evaluated. The estimated instrumental detection limit for a 2-s pressure injection of the FITC-DMA derivative was 50 pg/ml (10⁻⁹ M), using LIF detection with excitation and emission wavelengths of 488 nm and 520 nm, respectively. However, for practical reasons, a minimum of 5 ng/ml DMA should be subjected to the derivatization. The applicability of the described method to the extract of atmospheric aerosol samples was demonstrated.     

Simultaneous determination of iodate and periodate by capillary zone electrophoresis: application to carbohydrate analysis

Iodate and periodate were rapidly (in 11 min) separated from each other with high column efficiency by capillary zone electrophoresis, using a fused silica tube (50 microns i.d., 80 cm) and 100 mM acetate buffer, pH 4.5, as carrier. On-column uv detection at 222 nm allowed sensitive detection down to the picomole level, and measurement of relative peak area to that of pyromellitic acid (internal standard) enabled reproducible determination of these ions. This method was proved useful for periodate oxidation analysis of various carbohydrates.