Chitosan/Polyethylene Glycol Beads Crosslinked with Tripolyphosphate and Glutaraldehyde for Gastrointestinal Drug Delivery

This study reports on the preparation of chitosan (CS)/polyethylene glycol (PEG) hydrogel beads using sodium diclofenac (DFNa) as a model drug. Following the optimization of the polymer to drug ratio, the chitosan beads were modified by ionic crosslinking with sodium tripolyphosphate (TPP). The CS/PEG/DFNa beads obtained from a (w/w/w) ratio of 1/0.5/0.5 with crosslinking in 10% (w/v) TPP at pH 6.0 for 30 min yielded excellent DFNa encapsulation levels with over 90% loading efficiency. The dissolution profile of DFNa from CS/PEG/DFNa beads demonstrated that this formulation was able to maintain a prolonged drug release for approximately 8 h. Among the formulations tested, the CS/PEG/DFNa (1/0.5/1 (w/w/w)) beads crosslinked with a combination of TPP (10% (w/v) for 30 min) and glutaraldehyde (GD) (5% (w/v)) were able to provide minimal DFNa release in the gastric and duodenal simulated fluids (pH 1.2 and 6.8, respectively) allowing for a principally gradual drug release over 24 h in the intestinal (jejunum and ileum) simulated fluid (pH 7.4). Thus, overall the CS/PEG beads crosslinked with TPP and GD look to be a promising and novel alternative gastrointestinal drug release system.     

Design and evaluation of matrix-based controlled release tablets of diclofenac sodium and chondroitin sulphate

The purpose of the present study was to develop and characterize an oral controlled release drug delivery system for concomitant administration of diclofenac sodium (DS) and chondroitin sulfate (CS). A hydrophilic matrix-based tablet using different concentrations of hydroxypropylmethylcellulose (HPMC) was developed using wet granulation technique to contain 100 mg of DS and 400 mg of CS. Formulations prepared were evaluated for the release of DS and CS over a period of 9 hours in pH 6.8 phosphate buffer using United States Pharmacopeia (USP) type II dissolution apparatus. Along with usual physical properties, the dynamics of water uptake and erosion degree of tablet were also investigated. The in vitro drug release study revealed that HPMC K100CR at a concentration of 40% of the dosage form weight was able to control the simultaneous release of both DS and CS for 9 hours. The release of DS matched with the marketed CR tablet of DS with similarity factor (f(2)) above 50. Water uptake and erosion study of tablets indicated that swelling followed by erosion could be the mechanism of drug release. The in vitro release data of CS and DS followed Korsmeyer-Peppas and zero-order kinetics, respectively. In conclusion, the in vitro release profile and the mathematical models indicate that release of CS and DS can be effectively controlled from a single tablet using HPMC matrix system.     

Design and development of hydrogel beads for targeted drug delivery to the colon

The purpose of this research was to develop and evaluate a multiparticulate system of chitosan hydrogel beads exploiting pH-sensitive property and specific biodegradability for colon-targeted delivery of satranidazole. Chitosan hydrogel beads were prepared by the cross-linking method followed by enteric coating with Eudragit S100. All formulations were evaluated for particle size, encapsulation efficiency, swellability, and in vitro drug release. The size of the beads was found to range from 1.04±0.82 mm to 1.95±0.05 mm. The amount of the drug released after 24 hours from the formulation was found to be 97.67%±1.25% in the presence of extracellular enzymes as compared with 64.71%±1.91% and 96.52%±1.81% release of drug after 3 and 6 days of enzyme induction, respectively, in the presence of 4% cecal content. Degradation of the chitosan hydrogel beads in the presence of extracellular enzymes as compared with rat cecal and colonic enzymes indicates the potential of this multiparticulate system to serve as a carrier to deliver macromolecules specifically to the colon and can be offered as a substitute in vitro system for performing degradation studies. Studies demonstrated that orally administered chitosan hydrogel beads can be used effectively for the delivery of drug to the colon. Published: July 13, 2007     

Artemisia arborescens L essential oil loaded beads: Preparation and characterization

The purpose of this work was to prepare sodium alginate beads as a device for the controlled release of essential oil for oral administration as an antiviral agent. Different formulations were prepared with sodium alginate as a natural polymer and calcium chloride or glutaraldehyde as a cross-linking agent. Loading capacities of between 86% and 100% were obtained in freshly prepared beads by changing exposure time to the cross-linking agent. Drying of the calcium alginate beads caused only a slight decrease in the loading efficiency. The surface morphology of the different bead formulations were studied using scanning electron microscopy (SEM). Stability studies over a 3-month period showed that glutaraldehyde reacted with some components ofArtemisia arborescens L essential oil, changing its composition. Calcium alginate beads showed an in vitro controlled release of the essential oil for the investigated 24 hours, while the use of glutaraldehyde as a cross-linking agent was found not appropriate because of the interactions with azulene derivatives and the low degree of matrix cross-linkage. Published: August 24, 2007     

Effect of Drug Solubility on Polymer Hydration and Drug Dissolution from Polyethylene Oxide (PEO) Matrix Tablets

The purpose of the study was to investigate the effect of drug solubility on polymer hydration and drug dissolution from modified release matrix tablets of polyethylene oxide (PEO). Different PEO matrix tablets were prepared using acetaminophen (ACE) and ibuprofen (IBU) as study compounds and Polyox WSR301 (PEO) as primary hydrophilic matrix polymer. Tablet dissolution was tested using the USP Apparatus II, and the hydration of PEO polymer during dissolution was recorded using a texture analyzer. Drug dissolution from the preparations was dependent upon drug solubility, hydrogel formation and polymer proportion in the preparation. Delayed drug release was attributed to the formation of hydrogel layer on the surface of the tablet and the penetration of water into matrix core through drug dissolution and diffusion. A multiple linear regression model could be used to describe the relationship among drug dissolution, polymer ratio, hydrogel formation and drug solubility; the mathematical correlation was also proven to be valid and adaptable to a series of study compounds. The developed methodology would be beneficial to formulation scientists in dosage form design and optimization.     

Preparation and characterization of chitosan-polyvinyl alcohol blend hydrogels for the controlled release of nano-insulin

Chitosan (CS)-polyvinyl alcohol (PVA) blend hydrogels were prepared using glutaraldehyde as the cross-linking agent. The obtained hydrogels, which have the advantages of both PVA and CS, can be used as a material for the transdermal drug delivery (TDD) of insulin. The nano-insulin-loaded hydrogels were prepared under the following conditions: 1.2 g of polyethylene glycol, 1.5 g of CS, 1.2 g of PVA, 1.2 mL of 1% glutaraldehyde solution, 16 mL of water, and 40 mg of nano-insulin with 12 min of mixing time and 3 min of cross-linking time. The nano-insulin-loaded hydrogels were characterized using scanning electron microscopy, energy dispersive spectrometry, Fourier-transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, X-ray diffraction, and its mechanical properties were analyzed. The results show that all molecules in the hydrogel have good compatibility and they formed a honeycomb-like structure. The hydrogel also showed good mechanical and thermal properties. The in vitro drug release of the hydrogel showed that the nano-insulin accorded with Fick's first law of diffusion and it has a high permeation rate (4.421 μg/(cm² h)). These results suggest that the nano-insulin-loaded hydrogels are a promising non-invasive TDD system for diabetes chemotherapy.     

In Vitro and In Vivo Studies on Chitosan Beads of Losartan Duolite AP143 Complex, Optimized by Using Statistical Experimental Design

The aim of the present research work was to develop release modulated beads of losartan potassium complexed with anion exchange resin, Duolite AP143 (cholestyramine). Chitosan was selected as a hydrophilic polymer for the formation of beads which could sustain the release of the drug up to 12 h, along with drug resin complex (DRC). Chitosan beads were prepared using an in-liquid curing method by ionotropic cross-linking or interpolymer linkage with sodium tripolyphosphate (TPP). The formulation of the beads was optimized for entrapment efficiency and drug release using 3² full factorial design. The independent variables selected were DRC/chitosan and percent of TPP. The optimization model was validated for its performance characteristics. Studies revealed that as the concentration of chitosan and TPP was increased, entrapment efficiency and the drug release were found to increase and decrease, respectively. The swelling capacity of chitosan–TPP beads decreased with increasing concentration of TPP. The effect of chitosan concentration and percentage of TPP solution used for cross-linking on entrapment efficiency and drug release rate was extensively investigated. Optimized beads were subjected to in vivo studies in Wistar albino rats to determine the mean arterial blood pressure and compared with marketed formulation. The pharmacodynamic study demonstrates steady blood pressure control for optimized formulation as compared to fluctuated blood pressure for the marketed formulation.     

The study of gelation kinetics and chain-relaxation properties of glutaraldehyde-cross-linked chitosan gel and their effects on microspheres preparation and drug release

The effects of gelation kinetics and chain-relaxation properties of glutaraldehyde-cross-linked chitosan gel on microspheres preparation or drug release were studied. The rate of gelation is zero order corresponding to the chitosan concentration but non-zero order corresponding to the glutaraldehyde concentration. It was suggested that the cross-linking reaction was mainly dominated by the concentration of small molecule reactant, glutaraldehyde. The relaxation of an entangled polymer chain in a gel network as a result of the swelling of cross-linked chitosan hydrogel was investigated by the stress–strain determination. The higher the cross-linking density of chitosan hydrogel, the lower the swelling ability of chitosan hydrogel due to the slower relaxation rate of polymer chain, which then results in the decreased drug-release rate.     

Synthesis and characterization of pH-sensitive hydrogel composed of carboxymethyl chitosan for colon targeted delivery of ornidazole

In the present study, carboxymethyl chitosan was prepared from chitosan, crosslinked with glutaraldehyde and evaluated in vitro as a potential carrier for colon targeted drug delivery of ornidazole. Ornidazole was incorporated at the time of crosslinking of carboxymethyl chitosan. The chitosan was evaluated for its degree of deacetylation (DD) and average molecular weight; which were found to be 84.6% and 3.5×10(4) Da, respectively. The degree of substitution on prepared carboxymethyl chitosan was found to be 0.68. All hydrogel formulations showed more than 85% and 74% yield and drug loading, respectively. The swelling behaviour of prepared hydrogels checked in different pH values, 1.2, 6.8 and 7.4, indicated pH responsive swelling characteristic with very less swelling at pH 1.2 and quick swelling at pH 6.8 followed by linear swelling at pH 7.4 with slight increase. In vitro release profile was carried out at the same conditions as in swelling and drug release was found to be dependant on swelling of hydrogels and showed biphasic release pattern with non-fickian diffusion kinetics at higher pH. The carboxymethylation of chitosan, entrapment of drug and its interaction in prepared hydrogels were checked by FTIR, (1)H NMR, DSC and p-XRD studies, which confirmed formation of carboxymethyl chitosan from chitosan and absence of any significant chemical change in ornidazole after being entrapped in crosslinked hydrogel formulations. The surface morphology of formulation S6 checked before and after dissolution, revealed open channel like pores formation after dissolution.     

Controlled Release Matrix Tablets of Zidovudine: Effect of Formulation Variables on the <Emphasis Type="BoldItalic">In Vitro</Emphasis> Drug Release Kinetics

The purpose of this research was to design oral controlled release (CR) matrix tablets of zidovudine (AZT) using hydroxypropyl methylcellulose (HPMC), ethyl cellulose (EC) and carbopol-971P (CP) and to study the effect of various formulation factors on in vitro drug release. Release studies were carried out using USP type 1 apparatus in 900 ml of dissolution media. Release kinetics were analyzed using zero-order, Higuchi’s square root and Ritger–Peppas’ empirical equations. Release rate decreased with increase in polymer proportion and compression force. The release rate was lesser in formulations prepared using CP (20%) as compared to HPMC (20%) as compared to EC (20%). No significant difference was observed in the effect of pH of dissolution media on drug release from formulations prepared using HPMC or EC, but significant difference was observed in CP based formulations. Decrease in agitation speed from 100 to 50 rpm decreased release rate from HPMC and CP formulations but no significant difference was observed in EC formulations. Mechanism of release was found to be dependent predominantly on diffusion of drug through the matrix than polymer relaxation incase of HPMC and EC formulations, while polymer relaxation had a dominating influence on drug release than diffusion incase of CP formulations. Designed CR tablets with pH independent drug release characteristics and an initial release of 17–25% in first hour and extending the release up to 16–20 h, can overcome the disadvantages associated with conventional tablets of AZT.     

Preparation and characterization of a novel pH-sensitive chitosan-g-poly (acrylic acid)/attapulgite/sodium alginate composite hydrogel bead for controlled release of diclofenac sodium

A series of pH-sensitive composite hydrogel beads composed of chitosan-g-poly (acrylic acid)/attapulgite/sodium alginate (CTS-g-PAA/APT/SA) was prepared as drug delivery matrices crosslinked by Ca²⁺ owing to the ionic gelation of SA. The structure and surface morphology of the composite hydrogel beads were characterized by FTIR and SEM, respectively. pH-sensitivity of these composite hydrogels beads and the release behaviors of drug from them were investigated. The results showed that the composite hydrogel beads had good pH-sensitivity. The cumulative release ratios of diclofenac sodium (DS) from the composite hydrogel beads were 3.76% in pH 2.1 solution and 100% in pH 6.8 solutions within 24 h, respectively. However, the cumulative release ratio of DS in pH 7.4 solution reached 100% within 2 h. The DS cumulative release ratio reduced with increasing APT content from 0 to 50 wt%. The drug release was swelling-controlled at pH 6.8.     

Controlled release of tamoxifen citrate encapsulated in cross-linked guar gum nanoparticles

Natural polysaccharides, due to their outstanding merits, have received more and more attention in the field of drug delivery. In the present study tamoxifen citrate, TMX (a non-steroidal antiestrogenic drug) loaded guar gum nanoparticles, GG NPs, crosslinked with glutaraldehyde were prepared for treatment of breast cancer. An oil in water (o/w) emulsion polymer cross-linking method was employed for preparation of blank and drug loaded sustained release nature biodegradable nanoparticles. Prepared nanoparticles were characterized by morphology in scanning electron microscope (SEM), size distribution in transmission electron microscope (TEM), TMX loading by high performance liquid chromatography (HPLC) and in vitro drug release characteristics. An overall sustained release of the drug from the biodegradable nanoparticles was observed in in vitro release studies. The release of TMX from GG NPs was found to be effected by guar gum and glutaraldehyde concentration. Regression coefficient (R²) analysis suggested that the predominant mechanism behind the drug release from the nanoparticles was time dependent release and diffusion. In vivo studies on female albino mice demonstrated maximum uptake of the drug by mammary tissue after 24 h of administration with drug loaded guar gum nanoparticles in comparison with that with the tablet form of the drug. These findings demonstrate that controlled release of TMX from GG NPs could be a potential alternative pharmaceutical formulation in passive targeting of TMX in breast cancer treatments.     

Encapsulation of the peptide Ac-Glu-Thr-Lys-Thr-Tyr-Phe-Trp-Lys-NH2 into polyvinyl alcohol biodegradable formulations—Effect of calcium alginate

It has been recently reported that the peptide Ac-Glu-Thr-Lys-Thr-Tyr-Phe-Trp-Lys-NH₂, analogue of the Glu1811-Lys1818 region of A3 light chain of blood coagulation factor VIII, presents in vitro significant anticoagulant activity. The encapsulation of this peptide into different polyvinyl alcohol formulations is examined here. The formulations were prepared using polyvinyl alcohol cross-linked with either boric acid or glutaraldehyde, giving a series of twelve different hydrogels. In case of PVA-boric acid method, a small percentage of sodium alginate was used in order to avoid bead's agglomeration. In that case, the most efficient encapsulation of the octapeptide (74%) was achieved with 0.2% (w/w) sodium alginate. It was also observed that the increase in sodium alginate percentage leads to beads with increased peptide release time, ranging from 60 to 90 min at 0.02% and 1% (w/w) sodium alginate respectively. The water holding of the PVA gels was estimated to be 27% regardless of the cross-linking reagent used, while it was increased with increasing sodium alginate concentration and reached about 60% for 1% sodium alginate. The longer octapeptide release, at 120 min, was observed with PVA-glutaraldehyde hydrogel, with encapsulation efficiency comparable to those obtained with boric acid, indicating that this hydrogel may be further used in drug delivery systems.     

Preparation and characterization of cross-linked enzyme aggregates (CLEA) of subtilisin for controlled release applications

Enzyme stabilization is one of the major challenges in the biocatalytic process optimization. Subtilisin was aggregated using ammonium sulphate and polyethylene glycol with surfactants like triton X-100 and tween 20. The resultant aggregates on cross-linking with glutaraldehyde produced insoluble and catalytically active enzyme. The effect of pH, temperature, kinetic parameter, thermal stability and stability in organic solvents were studied. The cross-linked enzyme aggregates (CLEA) exhibited broad pH optima of 9.0 and higher temperature optima of 70 degrees C. Reusability and surface morphology of the CLEA were also studied. CLEA of subtilisin has good stability in nonpolar organic solvents, such as hexane, and cyclohexane and it has high thermal stability up to 60 degrees C and therefore can be used as a catalyst for the biotransformation of compounds which are not soluble in aqueous medium. The CLEAs were entrapped in the hydrogel composite beads of alginate:guar gum (3:1) which were resistant to low pH conditions in the stomach and thus was found to be useful for the oral drug delivery. This process can be used to deliver the protein and peptide drugs which involve high concentrations at the delivery stage, and which usually degrades in the stomach before reaching the jejunum. Application of these pH-sensitive beads for the controlled release of subtilisin in vitro was studied and found to be a feasible strategy.     

Influence of ibuprofen as a solid-state plasticizer in eudragit® RS 30 D on the physicochemical properties of coated beads

The purpose of this study was to investigate the physicochemical properties of nonpareil beads coated with Eudragit RS 30 D containing ibuprofen as a multifunctional agent. The influence of the concentration of ibuprofen in the film coating and the effect of the coating level on drug release from coated beads was determined in pH 7.2 phosphate buffer solution. The influence of storage time at 23 degrees C and 60 degrees C on the release of ibuprofen from coated beads was also investigated. The thermal properties of the films were determined using a differential scanning calorimeter. Scanning electron microscopy was employed to image the surface morphology of the coated beads. Infrared spectroscopy was used to study the interaction of Eudragit RS 30 D and ibuprofen. Results from the dissolution studies demonstrated that increasing the amount of ibuprofen in the polymeric film reduced the rate of drug release, mainly because of a more complete coalescence of the polymeric particles of the latex dispersion. The glass transition temperature (Tg) of Eudragit RS 30 D films decreased and the surface of the coated beads became smoother as the concentration of ibuprofen was increased. Hydrogen bonding between the polymer and ibuprofen was demonstrated by Fourier transform infrared spectroscopy. No significant differences were found in drug dissolution between the coated beads stored at 23 degrees C for 12 months and those stored at 60 degrees C for 12 hours. The results of this study demonstrated that the ibuprofen plasticized the Eudragit RS 30 D. Furthermore, the dissolution rate of ibuprofen can be controlled and changes in the drug release rate can be minimized by using the drug-induced plasticization technique with this polymer.     

Development of Push–Pull Osmotic Tablets Using Chitosan–Poly(Acrylic Acid) Interpolymer Complex as an Osmopolymer

The objectives of this study were to prepare push–pull osmotic tablets (PPOT) of felodipine using an interpolymer complex of chitosan (CS) and poly(acrylic acid) (PAA) as an osmopolymer, and to study the mechanisms of drug release from these tablets. The interpolymer complexes were prepared with different weight ratios of CS to PAA. Preparation of PPOT involved the fabrication of bilayered tablets with the drug layer, containing felodipine, polyethylene oxide, and the polymeric expansion layer, containing the CS–PAA complex. The effects of polymer ratios, type of plasticizers, and compression forces on release characteristics were investigated. It was found that drug release from PPOT exhibited zero-order kinetics and could be prolonged up to 12 or 24 h depending on the plasticizer used. PPOT using dibutyl sebacate showed a longer lag time and slower drug release than that using polyethylene glycol 400. In the case of polyethylene glycol 400, an increase in the CS proportion resulted in an increase in the drug release rate. The compression force had no effect on drug release from PPOT. Drug release was controlled by two consecutive mechanisms: an osmotic pump effect resulting in the extrusion of the drug layer from the tablet and subsequent erosion and dissolution of the extruded drug layer in the dissolution medium. The mathematical model (zero-order) related to extrusion and erosion rates for describing the mechanism of drug release showed a good correlation between predicted and observed values.     

Encapsulation of ciprofloxacin within modified xanthan gum- chitosan based hydrogel for drug delivery

The aim of the present work was to investigate the preparation of polyelectrolyte hydrogel as potential drug carrier for antibacterial Ciprofloxacin drug (CFX), intended for controlled release formulation. Hydrogel of N-trimehtyl chitosan (TMC)/sodium carboxymethyl xanthan gum (CMXG) was prepared and ciprofloxacin was employed as a model drug to investigate the loading and release performance of the prepared hydrogel. FTIR, DSC, TGA and SEM analysis were used to characterize the TMC/CMXG hydrogel and its CFX loaded hydrogel. The results showed that the ciprofloxacin was successfully incorporated and released from the prepared hydrogel without the loss of structural integrity or the change in its functionality. The encapsulation efficiency of CFX within the prepared hydrogel was found to be increased with increasing the concentration of drug reaching about 93.8 ± 2.1% with concentration of CFX 250 µg/ml. It was shown also that the drug is entrapped within the gel without significant interaction as confirmed from FTIR spectra and DSC analysis. In vitro release study in phosphate buffer saline (PBS), indicated the steady rise in cumulative drug release with the highest release amount, reaching about 96.1 ± 1.8% up to 150 min, whereby the gel with high drug loading efficiency (3.52 ± 0.07%) displayed faster and higher release rate than that of gel containing a smaller amount of drug (0.44 ± 0.01%). The release kinetics of loaded drug followed zero-order kinetics. CFX drug loaded hydrogel showed high activity against the gram positive and gram negative bacterial strains due to the successful released of CFX from the CFX loaded hydrogel into the tested bacterial strains with the highest diameter of inhibition zone against Escherichia coli (67.0 ± 1.0) as compared to reference antibiotic, Gentamicin (28 ± 0.5). Cytotoxicity of the prepared hydrogel was examined in vitro using lung human normal cell lines and showed the highest cell viability (97 ± 0.5%) at concentration up to 50 µg/ml. Consequently, TMC/CMXG hydrogel can be proposed as new controlled release drug delivery system.     

Design and study of lamivudine oral controlled release tablets

The objective of this study was to design oral controlled release matrix tablets of lamivudine using hydroxypropyl methylcellulose (HPMC) as the retardant polymer and to study the effect of various formulation factors such as polymer proportion, polymer viscosity, and compression force on the in vitro release of drug. In vitro release studies were performed using US Pharmacopeia type 1 apparatus (basket method) in 900 mL of pH 6.8 phosphate buffer at 100 rpm. The release kinetics were analyzed using the zero-order model equation, Higuchi's square-root equation, and the Ritger-Peppas empirical equation. Compatibility of the drug with various excipients was studied. In vitro release studies revealed that the release rate decreased with increase in polymer proportion and viscosity grade. Increase in compression force was found to decrease the rate of drug release. Matrix tablets containing 60% HPMC 4000 cps were found to show good initial release (26% in first hour) and extended the release up to 16 hours. Matrix tablets containing 80% HPMC 4000 cps and 60% HPMC 15,000 cps showed a first-hour release of 22% but extended the release up to 20 hours. Mathematical analysis of the release kinetics indicated that the nature of drug release from the matrix tablets was dependent on drug diffusion and polymer relaxation and therefore followed non-Fickian or anomalous release. No incompatibility was observed between the drug and excipients used in the formulation of matrix tablets. The developed controlled release matrix tablets of lamivudine, with good initial release (20%-25% in first hour) and extension of release up to 16 to 20 hours, can overcome the disadvantages of conventional tablets of lamivudine.     

“Development and Evaluation of Sodium Alginate–Polyacrylamide Graft–Co-polymer-Based Stomach Targeted Hydrogels of Famotidine”

In the present study, grafting technology has been used to develop novel grafted hydrogel beads as controlled drug delivery carriers. The chemical crosslinking and grafting of polyacrylamide onto sodium alginate has been found to be efficient method for the development of new polymeric carrier. The successful crosslinking has been confirmed by Fourier transformed infrared spectroscopy, thermogravimetric analysis, and elemental analysis. The polymeric network of sodium alginate–co-polyacrylamide (NaAlg-g-PAM) has been interlinked by covalent and hydrogen bonds which also strength the gel network. Simple ionotropic gelation method has been used for the preparation of NaAlg-g-PAM hydrogel beads. Its swelling and gelation were dependent on monomer and crosslinker concentrations. Entrapment of the drug moiety (famotidine; an antiulcer drug) within the grafted beads has been confirmed by X-ray powder diffraction and differential scanning calorimetry. More than 75% of drug loading in beads occurred with the increase of monomer and crosslinker concentration. In vitro drug release was found to be sustained up to the 12 h with 80% drug release.Key words: crosslinking, grafting, hydrogel beads, mechanical strength, polyacrylamide     

In vitro drug permeation from chitosan pellets

The purpose of this study was to prepare and characterize coated pellets for controlled drug delivery. The influence of chitosan (CS) in pellets was evaluated by swelling, in vitro drug release and intestinal permeation assays. Pellets were coated with an enteric polymer, Kollicoat^® MAE 30 DP, in a fluidized-bed apparatus and the coating formulations were based on a factorial design. Metronidazole (MT) released from coated and uncoated pellets were assessed by dissolution method using Apparatus I. Intestinal permeation was evaluated by everted intestinal sac model in rats, used to study the absorption of MT from coated pellets containing CS or not through the intestinal tissue. Although the film coating avoided drug dissolution in gastric medium, the overall drug release and intestinal permeation were dependent on the presence of CS. Thus, pellets containing CS show potential as a system for controlled drug delivery.