Controlled Release Matrix Tablets of Zidovudine: Effect of Formulation Variables on the <Emphasis Type="BoldItalic">In Vitro</Emphasis> Drug Release Kinetics

The purpose of this research was to design oral controlled release (CR) matrix tablets of zidovudine (AZT) using hydroxypropyl methylcellulose (HPMC), ethyl cellulose (EC) and carbopol-971P (CP) and to study the effect of various formulation factors on in vitro drug release. Release studies were carried out using USP type 1 apparatus in 900 ml of dissolution media. Release kinetics were analyzed using zero-order, Higuchi’s square root and Ritger–Peppas’ empirical equations. Release rate decreased with increase in polymer proportion and compression force. The release rate was lesser in formulations prepared using CP (20%) as compared to HPMC (20%) as compared to EC (20%). No significant difference was observed in the effect of pH of dissolution media on drug release from formulations prepared using HPMC or EC, but significant difference was observed in CP based formulations. Decrease in agitation speed from 100 to 50 rpm decreased release rate from HPMC and CP formulations but no significant difference was observed in EC formulations. Mechanism of release was found to be dependent predominantly on diffusion of drug through the matrix than polymer relaxation incase of HPMC and EC formulations, while polymer relaxation had a dominating influence on drug release than diffusion incase of CP formulations. Designed CR tablets with pH independent drug release characteristics and an initial release of 17–25% in first hour and extending the release up to 16–20 h, can overcome the disadvantages associated with conventional tablets of AZT.     

Once-daily sustained-release matrix tablets of nicorandil: Formulation and in vitro evaluation

The objective of the present study was to develop once-daily sustained-release matrix tablets of nicorandil, a novel potassium channel opener used in cardiovascular diseases. The tablets were prepared by the wet granulation method. Ethanolic solutions of ethylcellulose (EC), Eudragit RL-100, Eudragit RS-100, and polyvinylpyrrolidone were used as granulating agents along with hydrophilic matrix materials like hydroxypropyl methylcellulose (HPMC), sodium carboxymethylcellulose, and sodium alginate. The granules were evaluated for angle of repose, bulk density, compressibility index, total porosity, and drug content. The tablets were subjected to thickness, diameter, weight variation test, drug content, hardness, friability, and in vitro release studies. The granules showed satisfactory flow properties, compressibility, and drug content. All the tablet formulations showed acceptable pharmacotechnical properties and complied with in-house specifications for tested parameters. According to the theoretical release profile calculation, a oncedaily sustained-release formulation should release 5.92 mg of nicorandil in 1 hour, like conventional tablets, and 3.21 mg per hour up to 24 hours. The results of dissolution studies indicated that formulation F-I (drug-to-HPMC, 1∶4; ethanol as granulating agent) could extend the drug release up to 24 hours. In the further formulation development process, F-IX (drug-to-HPMC, 1∶4; EC 4% wt/vol as granulating agent), the most successful formulation of the study, exhibited satisfactory drug release in the initial hours, and the total release pattern was very close to the theoretical release profile. All the formulations (except F-IX) exhibited diffusion-dominated drug release. The mechanism of drug release from F-IX was diffusion coupled with erosion.     

Mucoadhesive vaginal tablets as veterinary delivery system for the controlled release of an antimicrobial drug,acriflavine

The aim of the study was the development of mucoadhesive vaginal tablets designed for the local controlled release of acriflavine, an antimicrobial drug used as a model. The tablets were prepared using drug-loaded chitosan microspheres and additional excipients (methylcellulose, sodium alginate, sodium carboxymethylcellulose, or Carbopol 974). The microspheres were prepared by a spray-drying method, using the drug to polymer weight ratios 1:1 and 1:2 and were characterized in terms of morphology, encapsulation efficiency, and in vitro release behavior, as MIC (Minimum Inhibitory Concentration), MBC (Minimum Bacterial Concentration), and killing time (KT). The tablets were prepared by direct compression, characterized by in vitro drug release and in vitro mucoadhesive tests. The microparticles have sizes of 4 to 12 microm; the mean encapsulation yields are about 90%. Acriflavine, encapsulated into the polymer, maintains its antibacterial activity; killing time of the encapsulated drug is similar to that of the free drug. In vitro release profiles of tablets show differences depending on the excipient used. In particular Carbopol 974, which is highly cross-linked, is able to determine a drug-controlled release from the matrix tablets for more than 8 hours. The in vitro adhesion tests, carried out on the same formulation, show a good adhesive behavior. The formulation containing microspheres with drug to polymer weight ratios of 1:1 and Carbopol 974 is characterized by the best release behavior and shows good mucoadhesive properties. These preliminary data indicate that this formulation can be proposed as a mucoadhesive vaginal delivery system for the controlled release of acriflavine.     

Controlled release formulation of tramadol hydrochloride using hydrophilic and hydrophobic matrix system

The effect of concentration of hydrophilic (hydroxypropyl methylcellulose [HPMC]) and hydrophobic polymers (hydrogenated castor oil [HCO], ethylcellulose) on the release rate of tramadol was studied. Hydrophilic matrix tablets were prepared by wet granulation technique, while hydrophobic (wax) matrix tablets were prepared by melt granulation technique and in vitro dissolution studies were performed using United States Pharmacopeia (USP) apparatus type II. Hydrophobic matrix tablets resulted in sustained in vitro drug release (>20 hours) as compared with hydrophilic matrix tablets (<14 hours). The presence of ethylcellulose in either of the matrix systems prolonged the release rate of the drug. Tablets prepared by combination of hydrophilic and hydrophobic polymers failed to prolong the drug release beyond 12 hours. The effect of ethylcellulose coating (Surelease) and the presence of lactose and HPMC in the coating composition on the drug release was also investigated. Hydrophobic matrix tablets prepared using HCO were found to be best suited for modulating the delivery of the highly water-soluble drug, tramadol hydrochloride.     

Hydrophilic excipients modulate the time lag of time-controlled disintegrating press-coated tablets

An oral press-coated tablet was developed by means of direct compression to achieve the time-controlled disintegrating or rupturing function with a distinct predetermined lag time. This press-coated tablet containing sodium diclofenac in the inner core was formulated with an outer shell by different weight ratios of hydrophobic polymer of micronized ethylcellulose (EC) powder and hydrophilic excipients such as spray-dried lactose (SDL) or hydroxypropyl methylcellulose (HPMC). The effect of the formulation of an outer shell comprising both hydrophobic polymer and hydrophilic excipients on the time lag of drug release was investigated. The release profile of the press-coated tablet exhibited a time period without drug release (time lag) followed by a rapid and complete release phase, in which the outer shell ruptured or broke into 2 halves. The lag phase was markedly dependent on the weight ratios of EC/SDL or EC/HPMC in the outer shell. Different time lags of the press-coated tablets from 1.0 to 16.3 hours could be modulated by changing the type and amount of the excipients. A semilogarithmic plot of the time lag of the tablet against the weight ratios of EC/SDL or EC/HPMC in the outer shell demonstrated a good linear relationship, withr=0.976 andr=0.982, respectively. The predetermined time lag prior to the drug release from a press-coated tablet prepared by using a micronized EC as a retarding coating shell can be adequately scheduled with the addition of hydrophilic excipients according to the time or site requirements.     

Evaluation of alginate compressed matrices as prolonged drug delivery systems

This research investigated the use of sodium alginate for the preparation of hydrophylic matrix tablets intended for prolonged drug release using ketoprofen as a model drug. The matrix tablets were prepared by direct compression using sodium alginate, calcium gluconate, and hydroxypropylmethylcellulose (HPMC) in different combinations and ratios. In vitro release tests and erosion studies of the matrix tablets were carried out in USP phosphate buffer (pH 7.4). Matrices consisting of sodium alginate alone or in combination with 10% and 20% of HPMC give a prolonged drug release at a fairly constant rate. Incorporation of different ratios of calcium gluconate leads to an enhancement of the release rate from the matrices and to the loss of the constant release rate of the drug. Only the matrices containing the highest quantity of HPMC (20%) maintained their capacity to release ketoprofen for a prolonged time.     

Method to recover a lipophilic drug from hydroxypropyl methylcellulose matrix tablets

A reverse-phase high-performance liquid chromatographic (HPLC) method for recovery of the lipophilic drug, alprazolam, from matrix tablets containing the hydrophilic polymer hydroxypropyl methylcellulose (HPMC) was developed. Lipophilic drugs, such as alprazolam, are difficult to completely extract and quantitate from tablets containing HPMC polymer. The percentage of recoveries of alprazolam from placebo powder spiked with alprazolam stock solution and from placebo powder mixed with alprazolam powder were about 100% and 85% to 95%, respectively. The validated method using water to completely dissolve HPMC before the addition of a strong solvent to dissolve and extract the drug from the HPMC solution was shown to be the most reproducible method. Different molecular weight distributions of the HPMC polymer, such as HPMC-K4M and HPMC-K100LV, did not influence the dissolution results of alprazolam using this validated method. Similarly, the excipients composing the matrix tablet formulations, such as dicalcium phosphate dihydrate, dicalcium phosphate anhydrous, calcium sulfate dihydrate, sucrose, dextrose, and lactose monohydrate, did not influence the percent recovery of alprazolam. The recovery method reported herein was shown to be the most efficient to achieve complete recovery of alprazolam from powder blends and tablets containing a variety of excipients and different grades of HPMC.     

Controlled Release Hydrophilic Matrix Tablet Formulations of Isoniazid: Design and In Vitro Studies

The aim of the present investigation was to develop oral controlled release matrix tablet formulations of isoniazid using hydroxypropyl methylcellulose (HPMC) as a hydrophilic release retardant polymer and to study the influence of various formulation factors like proportion of the polymer, polymer viscosity grade, compression force, and release media on the in vitro release characteristics of the drug. The formulations were developed using wet granulation technology. The in vitro release studies were performed using US Pharmacopoeia type 1 apparatus (basket method) in 900 ml of pH 7.4 phosphate buffer at 100 rpm. The release kinetics was analyzed using Korsmeyer–Peppas model. The release profiles were also analyzed using statistical method (one-way analysis of variance) and f ₂ metric values. The release profiles found to follow Higuchi’s square root kinetics model irrespective of the polymer ratio and the viscosity grade used. The results in the present investigation confirm that the release rate of the drug from the HPMC matrices is highly influenced by the drug/HPMC ratio and viscosity grade of the HPMC. Also, the effect of compression force and release media was found to be significant on the release profiles of isoniazid from HPMC matrix tablets. The release mechanism was found to be anomalous non-Fickian diffusion in all the cases. In the present investigation, a series of controlled release formulations of isoniazid were developed with different release rates and duration so that these formulations could further be assessed from the in vivo bioavailability studies. The formulations were found to be stable and reproducible.     

Guar Gum,Xanthan Gum,and HPMC Can Define Release Mechanisms and Sustain Release of Propranolol Hydrochloride

The objectives were to characterize propranolol hydrochloride-loaded matrix tablets using guar gum, xanthan gum, and hydroxypropylmethylcellulose (HPMC) as rate-retarding polymers. Tablets were prepared by wet granulation using these polymers alone and in combination, and physical properties of the granules and tablets were studied. Drug release was evaluated in simulated gastric and intestinal media. Rugged tablets with appropriate physical properties were obtained. Empirical and semi-empirical models were fit to release data to elucidate release mechanisms. Guar gum alone was unable to control drug release until a 1:3 drug/gum ratio, where the release pattern matched a Higuchi profile. Matrix tablets incorporating HPMC provided near zero-order release over 12 h and erosion was a contributing mechanism. Combinations of HPMC with guar or xanthan gum resulted in a Higuchi release profile, revealing the dominance of the high viscosity gel formed by HPMC. As the single rate-retarding polymer, xanthan gum retarded release over 24 h and the Higuchi model best fit the data. When mixed with guar gum, at 10% or 20% xanthan levels, xanthan gum was unable to control release. However, tablets containing 30% guar gum and 30% xanthan gum behaved as if xanthan gum was the sole rate-retarding gum and drug was released by Fickian diffusion. Release profiles from certain tablets match 12-h literature profiles and the 24-h profile of Inderal^® LA. The results confirm that guar gum, xanthan gum, and HPMC can be used for the successful preparation of sustained release oral propranolol hydrochoride tablets.     

Statistical evaluation of influence of viscosity and content of polymer on dipyridamole release from floating matrix tablets: A technical note

Conclusion  The present investigation described the influence of viscosity and content of HPMC on dipyridamole release using 3² full factorial design. All formulations had desired floating lag time (<2 minutes) regardless of viscosity and content of polymeric matrices. Results of multiple regression analysis indicate that both factors significantly affect the diffusion exponent (n), release rate constant (k), and percentage drug release at 1 hour, 4 hours, 6 hours, and 12 hour, (P<.05). Mechanism of drug release was found to be anomalous type to case-II transport depending upon the viscosity and content of polymer. It was found that content of HPMC had a dominant role in the initial phase of drug release, while in the later phase viscosity of HPMC Predominated. Published: August 24, 2007     

Terminalia Gum as a Directly Compressible Excipient for Controlled Drug Delivery

The exudates from the incised trunk of Terminalia randii has been evaluated as controlled release excipient in comparison with xanthan gum and hydroxypropylmethylcellulose (HPMC) using carvedilol (water insoluble) and theophylline (water soluble) as model drugs. Matrix tablets were prepared by direct compression and the effects of polymer concentration and excipients—spray dried lactose, microcrystalline cellulose and dicalcium phosphate dihydrate on the mechanical (crushing strength (CS) friability (F) and crushing strength–friability ratio (CSFR)) and drug release properties of the matrix tablets were evaluated. The drug release data were fitted into different release kinetics equations to determine the drug release mechanism(s) from the matrix tablets. The results showed that the CS and CSFR increased with increase in polymer concentration while F decreased. The ranking of CS and CSFR was HPMC > terminalia > xanthan while the ranking was reverse for F. The ranking for t ₂₅ (i.e. time for 25% drug release) at a polymer concentration of 60% was xanthan > terminalia = HPMC. The dissolution time, t ₂₅, of theophylline matrices was significantly lower (p < 0.001) than those of carvedilol matrix tablets. Drug release from the matrices was by swelling, diffusion and erosion. The mechanical and drug release properties of the tablets were significantly (p < 0.05) dependent on the type and concentration of polymer and excipients used with the release mechanisms varying from Fickian to anomalous. Terminalia gum compared favourably with standard polymers when used in controlled release matrices and could serve as a suitable alternative to the standard polymers in drug delivery.     

Correlating Cellulose Derivative Intrinsic Viscosity with Mechanical Susceptibility of Swollen Hydrophilic Matrix Tablets

Hydrophilic matrix tablets are prone to mechanical stress while passing through the gastrointestinal tract, which may result in inappropriate drug-release characteristics. Intrinsic viscosity is a physical polymer property that can be directly compared across various types and grades of polymers and correlated with the mechanical susceptibility of swollen matrix tablets. Five tablet formulations containing different HPMC and HPC polymers were prepared and analyzed using an in vitro glass bead manipulation test. The dissolution rate results were modeled using the Korsmeyer-Peppas equation and a correlation was found between the fit constants k and n, goodness-of-fit measure parameters, and intrinsic viscosity. Moreover, the dissolution profiles were used to calculate the degree of mechanical susceptibility for each formulation, defined as the ratio of the average dissolution rate after manipulation and the initial dissolution rate before manipulation. It was confirmed that an increased intrinsic viscosity polymer value resulted in a decrease in mechanical susceptibility. Considering this, two simple rules were defined for designing robust matrix tablets with respect to mechanical stresses.     

Use of hydrophilic natural gums in formulation of sustained-release matrix tablets of tramadol hydrochloride

The objective of this work was to develop matrix sustained-release tablets of highly water-soluble tramadol HCl using natural gums (xanthan [X gum] and guar [G gum]) as cost-effective, nontoxic, easily available, and suitable hydrophilic matrix systems compared with the extensively investigated hydrophilic matrices (ie, hydroxypropyl methylcellulose [HPMC]/carboxymethyl cellulose [CMC] with respect to in vitro drug release rate) and hydration rate of the polymers. Matrix tablets of tramadol (dose 100 mg) were produced by direct compression method. Different ratios, of 100∶0, 80∶20, 60∶40, 20∶80, 0∶100 of G gum (or X):HPMC, X gum:G gum, and triple mixture of these polymers (G gum, X gum, HPMC) were applied. After evaluation of physical characteristics of tablets, the dissolution test was, performed in the phosphate buffer media (pH 7.4) up to 8 hours. Tablets with only X had the highest mean dissolution time (MDT), the least dissolution efficiency (DE₈%), and released the drug following a zero-order model via swelling, diffusion, and erosion mechanisms. Guar gum alone could not efficiently control the drug release, while X and all combinations of natural gums with HPMC could retard tramadol HCl release. However, according to the similarity factor (f ₂), pure HPMC and H₈G₂ were the most similar formulations to Topalgic-LP as the reference standard. Published: March 17, 2006     

Formulation, Release Characteristics and Bioavailability Study of Oral Monolithic Matrix Tablets Containing Carbamazepine

This study examined the release of carbamazepine (CBZ) from hydrophobic (Compritol 888 ATO) and hydrophilic-hydrophobic matrix combination (Compritol 888 ATO-hydroxpropyl methylcellulose, HPMC). Hydrophobic matrix tablets were prepared by hot fusion technique, while hydrophilic-hydrophobic matrix tablets were prepared by wet granulation technique. The properties of the compressed matrix tablets were determined according to the US Pharmacopoeia. Both matrix formulations displayed a controlled-release profile when compared to the reference formulation (Tegretol CR 200). The bioavailability of CBZ formulations and Tegretol CR 200 were evaluated in beagle dogs. Carbamazepine presented a significant higher bioavailability from matrix tablets containing hydrophilic polymer (HPMC) than that obtained from Tegretol CR200. The average inter-subject plasma concentration variability CV% was the least with tablet containing hydrophilic polymer (HPMC) and was the highest with Tegretol CR 200 (33.8 and 54.1, respectively). Analysis of variance applied to log AUC(0-alpha) and log C(max) showed statistical significant differences among the three formulations (P < 0.05). Plotting the fraction of CBZ released in vitro and fraction absorbed showed a statistically significant relationship (R(2) = 0.935-0.975) for the three matrix tablets examined.     

Compressed matrix core tablet as a quick/slow dual-component delivery system containing ibuprofen

The purpose of the present research was to produce a quick/slow biphasic delivery system for ibuprofen. A dual-component tablet made of a sustained release tableted core and an immediate release tableted coat was prepared by direct compression. Both the core and the coat contained a model drug (ibuprofen). The sustained release effect was achieved with a polymer (hydroxypropyl methylcellulose [HPMC] or ethylcellulose) to modulate the release of the drug. The in vitro drug release profile from these tablets showed the desired biphasic release behavior: the ibuprofen contained in the fast releasing component was dissolved within 2 minutes, whereas the drug in the core tablet was released at different times (⊂16 or >24 hours), depending on the composition of the matrix tablet. Based on the release kinetic parameters calculated, it can be concluded that the HPMC core was suitable for providing a constant and controlled release (zero order) for a long period of time. Published: September 21, 2007     

Determining the Polymer Threshold Amount for Achieving Robust Drug Release from HPMC and HPC Matrix Tablets Containing a High-Dose BCS Class I Model Drug: In Vitro and In Vivo Studies

It is challenging to achieve mechanically robust drug-release profiles from hydrophilic matrices containing a high dose of a drug with good solubility. However, a mechanically robust drug release over prolonged period of time can be achieved, especially if the viscosity and amount of the polymer is sufficiently high, above the “threshold values.” The goal of this research was to determine the hydroxypropyl cellulose (HPC) and hydroxypropyl methylcellulose (HPMC) polymer threshold amount that would enable robust drug release from matrix tablets containing a high dose of levetiracetam as a class I model drug according to the Biopharmaceutical Classification System (BCS). For this purpose, formulations containing HPC or HPMC of similar viscosity range, but in different amounts, were prepared. Based on the dissolution results, two final formulations were selected for additional in vitro and in vivo evaluation to confirm the robustness and to show bioequivalence. Tablets were exposed to various stress conditions in vitro with the use of different mechanically stress-inducing dissolution methods. The in vitro results were compared with in vivo results obtained from fasted and fed bioequivalence studies. Under both conditions, the formulations were bioequivalent and food had a negligible influence on the pharmacokinetic parameters C_max and area under the curve (AUC). It was concluded that the drug release from both selected formulations is mechanically robust and that HPC and HPMC polymers with intrinsic viscosities above 9 dL/g and in quantities above 30% enable good mechanical resistance, which ensures bioequivalence. In addition, HPC matrices were found to be more mechanically robust compared to HPMC.KEY WORDS: HPC, HPMC, matrix tablets, mechanically robust dissolution, threshold amount     

Controlled-Release Carbamazepine Granules and Tablets Comprising Lipophilic and Hydrophilic Matrix Components

The objective of this study was to investigate the effect of lipophilic (Compritol 888 ATO) and hydrophilic components (combination of HPMC and Avicel) on the release of carbamazepine from granules and corresponding tablet. Wet granulation followed by compression was employed for preparation of granules and tablets. The matrix swelling behavior was investigated. The dissolution profiles of each formulation were compared to those of Tegretol CR tablets and the mean dissolution time (MDT), dissolution efficiency (DE %) and similarity factor (f(2) factor) were calculated. It was found that increase in the concentration of HPMC results in reduction in the release rate from granules and achievement of zero-order is difficult from the granules. The amount of HPMC plays a dominant role for the drug release. The release mechanism of CBZ from matrix tablet formulations follows non-Fickian diffusion shifting to case II by the increase of HPMC content, indicating significant contribution of erosion. Increasing in drug loading resulted in acceleration of the drug release and in anomalous controlled-release mechanism due to delayed hydration of the tablets. These results suggest that wet granulation followed by compression could be a suitable method to formulate sustained release CBZ tablets.     

Effect of hydroxypropyl methylcellulose and hydrogenated castor oil on naproxen release from sustained-release tablets

The effect of the concentration of hydrophilic (hydroxypropyl methylcellulose [HPMC]) and hydrophobic (hydrogenated castor oil [HCO]) products, fillers (lactose and dibasic calcium phosphate), and buffers (sodium bicarbonate, calcium carbonate, and sodium citrate) on naproxen release rate was studied. Matrix tablets were prepared by double compression, andIn vitro dissolution tests were performed. The dissolution results showed that an increased amount of HPMC or hydrogenated castor oil resulted in reduced drug release. The inclusion of buffers in the HPMC matrix tablets enhanced naproxen release. For HCO tablets, only sodium bicarbonate enhanced naproxen release. The presence of lactose on HPMC matrix tablets did not show a significantly different result from that obtained with the formulation containing dibasic calcium phosphate as a filler. However, for the tablets containing HCO, the presence of lactose significantly enhanced the naproxen release rate. The matrix-forming materials in this study were suitable for use in sustained-release tablets containing naproxen. The drug release can be modulated by adding suitable amounts of diluents and buffers.     

Formulation of Controlled-Release Baclofen Matrix Tablets II: Influence of Some Hydrophobic Excipients on the Release Rate and In Vitro Evaluation

The aim of this study was to investigate the influence of polymer level and type of some hydrophobic polymers, including hydrogenated castor oil (HCO); Eudragit RS100 (E-RS100); Eudragit L100 (E-L100), and some fillers namely mannitol [soluble filler], Dibasic calcium phosphate dihydrate (Emcompress) and anhydrous dibasic calcium phosphate [insoluble fillers] on the release rate and mechanism of baclofen from matrix tablets prepared by a hot-melt granulation process (wax tablets) and wet granulation process (E-RS100 and E-L100 tablets). Statistically significant differences were found among the drug release profile from different classes of polymeric matrices. Higher polymeric content (40%) in the matrix decreased the release rate of drug because of increased tortuosity and decreased porosity. At lower polymeric level (20%), the rate and extent of drug release was elevated. HCO was found to cause the strongest retardation of drug. On the other hand, replacement of Emcompress or anhydrous dibasic calcium phosphate for mannitol significantly retarded the release rate of baclofen, except for E-L100 (pH-dependent polymer). Emcompress surface alkalinity and in-situ increase in pH of the matrix microenvironment enhanced the dissolution and erosion of these matrix tablets. The release kinetics was found to be governed by the type and content of the excipients (polymer or filler). The prepared tablets showed no significant change in drug release rate when stored at ambient room conditions for 6 months.     

盐酸小檗碱缓释片的研制

目的:研究盐酸小檗碱缓释片的配方与制备方法,考察其释放度。方法:以盐酸小檗碱释放度为考察指标,采用单因素试验法,考察了羟丙基甲基纤维素(HPMC)和乳糖的用量对药物体外释放行为的影响,并采用正交设计实验对处方进行优化,确定最佳处方。结果:最佳配方为HPMC-K4M的用量为10%,乳糖用量为20%,PVP的用量为3%,微晶纤维素的用量为20%。2 h累积释药量为30%,6 h累积释药量为60%,12 h累积释药量为90%。结论:按最佳配方制备的盐酸小檗碱缓释片有较好的缓释行为,基本上能满足缓释片的释放要求。