Coadsorption of human milk lactoferrin into the dipalmitoylglycerolphosphatidylcholine phospholipid monolayer spread at the air/water interface

The coadsorption of human milk lactoferrin into a spread monolayer of dipalmitoylglycerol phosphatidylcholine (DPPC) at the air/water interface has been studied by neutron reflection. The system is a good model of the preocular tear film outer interface, which was the motivation for the study. The association of the protein with the surface was indicated by an increase of the surface pressure exerted by the DPPC monolayer. The extent of lactoferrin coadsorption was found to decrease with increasing surface pressure in the lipid monolayer, a trend consistent with the observation reported for other proteins, such as lysozyme and beta-lactoglobulin. The neutron reflectivity measurements were subsequently carried out at the three surface pressures of 8, 15, and 35 mN/m to examine the structure and composition of lactoferrin coadsorbed at the interface. Whereas the DPPC monolayer effectively prevented lactoferrin insertion at the high surface pressure, a measurable amount of lactoferrin was found at the air/water interface at the two lower surface pressures. At 15 mN/m it was difficult to identify the distribution of lactoferrin with respect to the DPPC monolayer, due to its relatively low adsorbed amount and much broader distribution. At the lowest surface pressure of 8 mN/m, the lactoferrin coadsorption was found to increase with time over the first few hours. After 5 h the distribution of the lactoferrin layer became similar to, though quantitatively lower than, that adsorbed in the absence of the DPPC monolayer. It is characterized by a top dense sublayer of 15 A with a bottom diffuse sublayer of 60 A, indicating structural unfolding induced by surface adsorption under these conditions.     

Reversible self-association of ovalbumin at air-water interfaces and the consequences for the exerted surface pressure

In this study the relation between the ability of protein self-association and the surface properties at air-water interfaces is investigated using a combination of spectroscopic techniques. Three forms of chicken egg ovalbumin were obtained with different self-associating behavior: native ovalbumin, heat-treated ov-albumin-being a cluster of 12-16 predominantly noncovalently bound proteins, and succinylated ovalbumin, as a form with diminished aggregation properties due to increased electrostatic repulsion. While the bulk diffusion of aggregated protein is clearly slower compared to monomeric protein, the efficiency of transport to the interface is increased, just like the efficiency of sticking to rather than bouncing from the interface. On a timescale of hours, the aggregated protein dissociates and adopts a conformation comparable to that of native protein adsorbed to the interface. The exerted surface pressure is higher for aggregated material, most probably because the deformability of the particle is smaller. Aggregated protein has a lower ability to desorb from the interface upon compression of the surface layer, resulting in a steadily increasing surface pressure upon reducing the available area for the surface layer. This observation is opposite to what is observed for succinylated protein that may desorb more easily and thereby suppresses the buildup of a surface pressure. Generally, this work demonstrates that modulating the ability of proteins to self-associate offers a tool to control the rheological properties of interfaces.     

Protein adsorption at the oil/water interface: characterization of adsorption kinetics by dynamic interfacial tension measurements.

The dynamics of protein adsorption at an oil/water interface are examined over time scales ranging from seconds to several hours. The pendant drop technique is used to determine the dynamic interfacial tension of several proteins at the heptane/aqueous buffer interface. The kinetics of adsorption of these proteins are interpreted from tension/log time plots, which often display three distinct regimes. (I) Diffusion and protein interfacial affinity determine the duration of an initial induction period of minimal tension reduction. A comparison of surface pressure profiles at the oil/water and air/water interface reveals the role of interfacial conformational changes in the early stages of adsorption. (II) Continued rearrangement defines the second regime, where the resulting number of interfacial contacts per protein molecule causes a steep tension decline. (III) The final regime occurs upon monolayer coverage, and is attributed to continued relaxation of the adsorbed layer and possible build-up of multilayers. Denaturation of proteins by urea in the bulk phase is shown to affect early regimes.     

Effect of Acetylation of Ovalbumin on Its Adsorption Behavior at Solid/Liquid Interface

This paper reports the effect of modification of lysine residues on the adsorption of ovalbumin at alumina/water interface. It has been shown that the pH dependence of the adsorption changes on acetylation of lysine. Thus at pH 7.6 acetylated ovalbumin does not show any affinity for alumina surface although unmodified protein does. It seems that although electrostatic interactions are operative, surface unfolding of proteins and surface hydrophobicity of protein also control the adsorption of ovalbumin onto alumina.     

Atypical Langmuir adsorption of inhalation anesthetics on phospholipid monolayer at various compressional states: difference between alkane-type and ether-type anesthetics

Adsorption of chloroform, halothane, enflurane and diethyl ether on the air/water interface was compared with adsorption on the dipalmitoylphosphatidylcholine monolayer, spread on the air/water interface, at four compressional states; 88.5, 77.0, 66.5 and 50.5 A2 surface area per phosphatidylcholine molecule. Anesthetics were administered from the gas phase. The affinities of these agents to the phosphatidylcholine monolayer varied according to the state of the monolayer. Chloroform and halothane showed a stronger affinity to the highly compressed phosphatidylcholine monolayer (50.5 A2) than to the expanded monolayer (88.5 A2) or to the air/water interface without the monolayer. Diethyl ether behaved in reverse; a stronger affinity to the expanded monolayer was exhibited than to the compressed monolayer. Enflurane showed the highest affinity to the intermediately compressed monolayer (77.0 A2). The adsorption isotherm of anesthetics to the monolayer was characterized by atypical Langmuir-type, in which available number of binding sites changed when anesthetics were adsorbed. The mode of adsorption onto the monolayer was dissimilar to adsorption onto air/water interface, where adsorption followed the Gibbs surface excess. A theory is presented to explain the above differences. The adsorbed anesthetic molecules do not stick to phosphatidylcholine molecules but penetrate into the monolayer lattice and occupy the phosphatidylcholine sites at the interface. Quantitative agreement between the theory and the experimental data was excellent. For the monolayer at 50.5 A2 compression, the changes in the transfer free energy accompanying the anesthetic adsorption from the gas phase to the monolayer were in the order of chloroform greater than halothane greater than enflurane greater than diethyl ether, in agreement with the clinical potencies.     

Secondary structure of spiralin in solution, at the air/water interface, and in interaction with lipid monolayers

The surface of spiroplasmas, helically shaped pathogenic bacteria related to the mycoplasmas, is crowded with the membrane-anchored lipoprotein spiralin whose structure and function are unknown. In this work, the secondary structure of spiralin under the form of detergent-free micelles (average Stokes radius, 87.5 A) in water and at the air/water interface, alone or in interaction with lipid monolayers was analyzed. FT-IR and circular dichroism (CD) spectroscopic data indicate that spiralin in solution contains about 25+/-3% of helices and 38+/-2% of beta sheets. These measurements are consistent with a consensus predictive analysis of the protein sequence suggesting about 28% of helices, 32% of beta sheets and 40% of irregular structure. Brewster angle microscopy (BAM) revealed that, in water, the micelles slowly disaggregate to form a stable and homogeneous layer at the air/water interface, exhibiting a surface pressure up to 10 mN/m. Polarization modulation infrared reflection absorption spectroscopy (PMIRRAS) spectra of interfacial spiralin display a complex amide I band characteristic of a mixture of beta sheets and alpha helices, and an intense amide II band. Spectral simulations indicate a flat orientation for the beta sheets and a vertical orientation for the alpha helices with respect to the interface. The combination of tensiometric and PMIRRAS measurements show that, when spiroplasma lipids are used to form a monolayer at the air/water interface, spiralin is adsorbed under this monolayer and its antiparallel beta sheets are mainly parallel to the polar-head layer of the lipids without deep perturbation of the fatty acid chains organization. Based upon these results, we propose a 'carpet model' for spiralin organization at the spiroplasma cell surface. In this model, spiralin molecules anchored into the outer leaflet of the lipid bilayer by their N-terminal lipid moiety are composed of two colinear domains (instead of a single globular domain) situated at the lipid/water interface. Owing to the very high amount of spiralin in the membrane, such carpets would cover most if not all the lipids present in the outer leaflet of the bilayer.     

Second harmonic generation of glucose oxidase at the air/water interface

We present a study of the adsorption of the glucose oxidase enzyme (GOx) at the air/water interface, using the nonlinear optical technique of surface second harmonic generation (SSHG). Resonant SSHG experiments were achieved by probing the pi-pi* transition of the flavin adenine dinucleotide (FAD) chromophores embedded in the GOx protein. Because of the subsequent resonance enhancement of the signal, the second harmonic (SH) wave arising from the GOx entities adsorbed at the interface was detectable for protein bulk aqueous concentrations as low as 70 nM. The protein adsorption was followed, and, at high GOx coverage, a change in the orientation of the FAD chromophore was observed, indicating either a rearrangement or a reorientation of the protein at the interface. Inasmuch as GOx is negatively charged at the biological pH of 7, its interactions with charged surfactants were also investigated. As expected, spreading positively charged surfactants onto a partial protein monolayer was found to increase the GOx surface concentration, whereas in the case of negatively charged surfactants, the GOx surface concentration decreased until the SH signal went back to the pure buffer solution response level. With the increasing GOx surface concentration, the rearrangement or reorientation of the protein was also observed.     

Formation and properties of Langmuir and Gibbs monolayers: a comparative study using hydrogenated and partially fluorinated amphiphilic derivatives of mannitol

The synthesis and surface behavior of a series of nine new hydrogenated nonionic surfactants and their fluorinated analogs, derived from D-mannitol are described. Adsorption monolayers (Gibbs monolayers) were studied by surface pressure (H) measurements as a function of time. For the spread monolayers (Langmuir monolayers), the measurements of surface pressure versus molecular area (A) were performed. For the most hydrophobic amphiphiles at low concentrations, the adsorption at the air/water interface from the bulk solution required extremely long times to attain equilibrium. The A values for two compounds which could be studied in both adsorbed and spread monolayers provided data allowing a direct comparison of the properties of the two types of films formed at the air/water interface. In spite of different mechanisms of formation of Langmuir and Gibbs monolayers, their characteristic parameters were identical, proving the equivalence of these two types of structures.     

Molecular dynamics simulation of the cooperative adsorption of barley lipid transfer protein and cis-isocohumulone at the vacuum-water interface

Molecular dynamic simulations have been carried out on systems containing a mixture of barley lipid transfer protein (LTP) and cis-isocohumulone (a hop derived iso-alpha-acid) in one of its enol forms, in bulk water and at the vacuum-water interface. In solution, the cis-isocohumulone molecules bind to the surface of the LTP molecule. The mechanism of binding appears to be purely hydrophobic in nature via desolvation of the protein surface. Binding of hop acids to the LTP leads to a small change in the 3-D conformation of the protein, but no change in the proportion of secondary structure present in helices, even though there is a significant degree of hop acid binding to the helical regions. At the vacuum-water interface, cis-isocohumulone shows a high surface activity and adsorbs rapidly at the interface. LTP then shows a preference to bind to the preadsorbed hop acid layer at the interface rather than to the bare water-vacuum interface. The free energy of adsorption of LTP at the hop-vacuum-water interface is more favorable than for adsorption at the vacuum-water interface. Our results support the view that hop iso-alpha-acids promote beer foam stability by forming bridges between separate adsorbed protein molecules, thus strengthening the adsorbed protein layer and reducing foam breakdown by lamellar phase drainage. The results also suggest a second mechanism may also occur, whereby the concentration of protein at the interface is increased via enhanced protein adsorption to adsorbed hop acid layers. This too would increase foam stability through its effect on the stabilizing protein layer around the foam bubbles.     

Physicochemical characterisation of enzymatically hydrolysed derivatives of acetylated starch

Potato starch modified to different degrees by substitution with acetyl groups was the subject of this study undertaken to determine the influence of conditions of enzymatic hydrolysis on the surface-active properties of hydrolysates of acetylated starch. The effect of acetylation of starch preparation on its susceptibility to enzymatic hydrolysis in the membrane reactor was also considered. All hydrolysates of acetylated starch samples investigated were found to bring a decrease in the surface/interfacial tension, both at the air/water and the toluene/water interfaces. For binary hydrolysate-surfactant systems, the surface mole fractions in the mixed adsorbed monolayer at the air/water interface were estimated. For mixed systems, the synergism in reducing the surface tension at the air/water interface was observed. The experimentally obtained dynamic surface tension data for the aqueous solution of acetylated starch hydrolysates were used to estimate the diffusion coefficients. Particle size distributions of the hydrolysates formed in the aqueous solutions were compared to those of commercial maltodextrin.     

A comparison of the surface activities of human apolipoproteins A-I and A-II at the air/water interface

Surface pressure (pi) and adsorption isotherms for human apolipoproteins A-I and A-II at the air/water interface have been determined and used to deduce the probable molecular structures of the monomolecular films. The surface concentrations were measured using the surface radioactivity method to monitor the adsorption of reductively [14C]methylated apoproteins. Apolipoprotein A-I and apolipoprotein A-II are extremely surface-active proteins and adsorb to exert maximal pi values of 22 and 24 mN.m-1 respectively, at a steady-state subphase concentration of about 3.10(-5) g/100 ml (equivalent to 11 and 17 nM for apolipoprotein A-I and apolipoprotein A-II, respectively). At saturation monolayer coverage, the average molecular areas for apolipoprotein A-I and apolipoprotein A-II are 15 and 13 A2/residue, respectively. These packing densities are consistent with monolayers consisting largely of alpha-helical protein molecules lying with the long axes of the helical segments in the plane of the interface. Comparison of the molecular packings of spread and adsorbed monolayers of these proteins indicates that at low pi values, the adsorbed films are more expanded, but at high pi values, the molecular packing in both types of film is the same.     

Molecular dynamics study of the folding of hydrophobin SC3 at a hydrophilic/hydrophobic interface

Hydrophobins are fungal proteins that self-assemble at hydrophilic/hydrophobic interfaces into amphipathic membranes. These assemblages are extremely stable and posses the remarkable ability to invert the polarity of the surface on which they are adsorbed. Neither the three-dimensional structure of a hydrophobin nor the mechanism by which they function is known. Nevertheless, there are experimental indications that the self-assembled form of the hydrophobins SC3 and EAS at a water/air interface is rich with beta-sheet secondary structure. In this paper we report results from molecular dynamics simulations, showing that fully extended SC3 undergoes fast (approximately 100 ns) folding at a water/hexane interface to an elongated planar structure with extensive beta-sheet secondary elements. Simulations in each of the bulk solvents result in a mainly unstructured globular protein. The dramatic enhancement in secondary structure, whether kinetic or thermodynamic in origin, highlights the role interfaces between phases with large differences in polarity can have on folding. The partitioning of the residue side-chains to one of the two phases can serve as a strong driving force to initiate secondary structure formation. The interactions of the side-chains with the environment at an interface can also stabilize configurations that otherwise would not occur in a homogenous solution.     

Two-dimensional crystals of Escherichia coli RNA polymerase holoenzyme on positively charged lipid layers

Escherichia coli RNA polymerase holoenzyme forms two-dimensional crystals when adsorbed to positively charged lipid layers at the air/water interface. Adsorption of the protein is driven by electrostatic interactions between the positively charged lipid surface and the polymerase molecule, which has a net negative charge. Crystallization is dependent on the adsorption and concentration of RNA polymerase on fluid lipid surfaces. Image analysis of electron micrographs of crystals in negative stain, which diffract to 30 A resolution, shows irregularly shaped protein densities about 100 x 160 A, consistent with the dimensions of single polymerase molecules.     

Role of pulmonary surfactant components in surface film formation and dynamics

Pulmonary surfactant is a mixture of lipids and proteins which is secreted by the epithelial type II cells into the alveolar space. Its main function is to reduce the surface tension at the air/liquid interface in the lung. This is achieved by forming a surface film that consists of a monolayer which is highly enriched in dipalmitoylphosphatidylcholine and bilayer lipid/protein structures closely attached to it. The molecular mechanisms of film formation and of film adaptation to surface changes during breathing in order to remain a low surface tension at the interface, are unknown. The results of several model systems give indications for the role of the surfactant proteins and lipids in these processes. In this review, we describe and compare the model systems that are used for this purpose and the progress that has been made. Despite some conflicting results using different techniques, we conclude that surfactant protein B (SP-B) plays the major role in adsorption of new material into the interface during inspiration. SP-C's main functions are to exclude non-DPPC lipids from the interface during expiration and to attach the bilayer structures to the lipid monolayer. Surfactant protein A (SP-A) appears to promote most of SP-B's functions. We describe a model proposing that SP-A and SP-B create DPPC enriched domains which can readily be adsorbed to create a DPPC-rich monolayer at the interface. Further enrichment in DPPC is achieved by selective desorption of non-DPPC lipids during repetitive breathing cycles.     

The interaction of liposomes containing intrinsic erythrocyte membrane proteins with lipid monolayers at air/water and oil/water interfaces

The main intrinsic membrane proteins of the human erythrocyte membrane, glycophorin and the anion transporter, were isolated by extraction with Triton X-100 and ion-exchange chromatography. After removal of detergent the extract consisted of proteolipid vesicles with a lipid:protein molar ratio in the range 50-60 and a diameter of the order of 200 nm. The interaction between these vesicles and dipalmitoylphosphatidylcholine (DPPC), cholesterol and cholesterol:DPPC (2:1 molar ratio) monolayers at air/water and n-decane/water interfaces has been studied. The vesicles interact with the monolayers, rapidly causing large increases in surface pressure. Limiting values of surface pressure, 39.4-43 mN . m-1 at air/water and 31.5-33.4 mN . m-1 at the n-decane/water interface, were reached at protein levels above 1 microgram . ml-1. At the air/water interface, and probably at the n-decane/water, surface pressure increases were limited by monolayer collapse. Compression isotherms and surface potential measurements indicated that material from the proteolipid vesicles entered the monolayer phase. In contrast to proteolipid vesicles, injection of protein-free liposomes beneath the monolayer resulted in smaller, slower increases in surface pressure. Thus, the presence of intrinsic membrane proteins in vesicles greatly facilitated the transfer of material into the lipid monolayer.     

Biological membrane modeling with a liquid/liquid interface. Probing mobility and environment with total internal reflection excited fluorescence.

Total internal reflection of exciting light, in combination with fluorescence intensity and polarization measurements, was used to selectively study fluorescent compounds adsorbed to the interface region between two immiscible liquids. A fluorometer was constructed which provided excitation at variable angles of incidence and allowed sensitive detection of polarized fluorescence emitted from the interface. The compound 4,4'-bis-1-phenylamino-8-naphthalenesulfonate (bis-ANS) was examined at a decalin/water interface and was found to possess remarkable affinity for the interface region with the bulk of the adsorbed molecule residing in the decalin phase. The adsorbed fluorophore displayed an apparent hindered rotation in the plane of the interface with a rotational diffusion coefficient 3- to 12-fold lower than that expected for bis-ANS in solution. While other dyes examined were not found to be significantly surface active, the addition of cationic surfactant sufficed to induce adsorption of the anionic fluorophore 1-aminonaphthalene-3,6,8-trisulfonic acid. This fluoropore was found to reside in an aqueous environment when bound to the interface, and it also exhibited hindered rotation in the plane of the interface. As the concentrations of the dyes were increased, both adsorbed dyes exhibited polarization reductions consistent with excitation energy transfer. Adsorption of bis-ANS was reversed by addition of bovine serum albumin. The membrane protein cytochrome b5 was found not to bind at the decalin/water interface, indicating that interaction with lipid is required for its adherence to biological membranes.     

An analysis of the interaction of protein with lipid monolayers at the air/water interface

1. Measurements have been made of the interaction of cytochrome c, bovine serum albumin and synthetic oxytocin with low-pressure (2dyn/cm) monolayers of stearic acid, phosphatidylcholine and phosphatidylethanolamine. 2. [(14)C]Carboxymethylation of the cytochrome c and albumin followed by surface-radioactivity determinations have shown that only a proportion of the protein added to the subphase is bound to the monolayers and that initially the degree of binding is dependent on the protein concentration. The binding is irreversible in the sense that the adsorbed protein cannot be removed by transferring the film containing the interacted protein to a fresh subphase containing no protein. 3. Three successive types of interaction can usually be recognized. (a) Initially, whole molecules of protein penetrate the lipid film and occupy the same area as those of the protein spread at the air/water interface. (b) Above certain film pressures a part of each protein molecule, probably hydrophobic side chains, penetrates the film. The change in surface pressure per unit of bound protein is much smaller than in (a). (c) At higher film pressures, adsorption without penetration occurs. With cytochrome c this is initially dependent on a favourable electrostatic interaction.     

Multilayers at the surface of solutions of exogenous lung surfactant: direct observation by neutron reflection

Pharmacy-grade exogenous lung surfactant preparations of bovine and porcine origin, dispersed in physiological electrolyte solution have been studied. The organization and dynamics at the air/water interface at physiological temperature was analysed by neutron reflection. The results show that a well-defined surface phase is formed, consisting of a multilayer structure of lipid/protein bilayers alternating with aqueous layers, with a repetition period of about 70 A and correlation depths of 3 to >25 bilayers, depending on electrolyte composition and time. The experimental surfactant concentration of 0.15% (w/w) is far below that used in therapeutic application of exogenous surfactants and it is therefore likely that similar multilayer structures are also formed at the alveolar surface in the clinical situation during surfactant substitution therapy. Lung surfactant preparations in dry form swell in aqueous solution towards a limit of about 60% (w/w) of water, forming a lamellar liquid-crystalline phase above about 34 degrees C, which disperses into lamellar bodies at higher water concentrations. The lamellar spacings in the surface multilayers at the air/water interface are smaller than those in the saturated limit even though they are in contact with much greater water concentrations. The surface multilayers are laterally disordered in a way that is consistent with fragments of Lalpha-phase lamellae. The near surface layers of the multilayer structure have a significant protein content (only SP-B and SP-C are present in the preparations). The results demonstrate that a multilayer structure can be formed in exogenous surfactant even at very low concentrations and indicate that multilayers need to be incorporated into present interpretations of in vitro studies of similar lung surfactant preparations, which are largely based on monolayer models.     

Adsorption of frog foam nest proteins at the air-water interface

The surfactant properties of aqueous protein mixtures (ranaspumins) from the foam nests of the tropical frog Physalaemus pustulosus have been investigated by surface tension, two-photon excitation fluorescence microscopy, specular neutron reflection, and related biophysical techniques. Ranaspumins lower the surface tension of water more rapidly and more effectively than standard globular proteins under similar conditions. Two-photon excitation fluorescence microscopy of nest foams treated with fluorescent marker (anilinonaphthalene sulfonic acid) shows partitioning of hydrophobic proteins into the air-water interface and allows imaging of the foam structure. The surface excess of the adsorbed protein layers, determined from measurements of neutron reflection from the surface of water utilizing H(2)O/D(2)O mixtures, shows a persistent increase of surface excess and layer thickness with bulk concentration. At the highest concentration studied (0.5 mg ml(-1)), the adsorbed layer is characterized by three distinct regions: a protruding top layer of approximately 20 angstroms, a middle layer of approximately 30 angstroms, and a more diffuse submerged layer projecting some 25 angstroms into bulk solution. This suggests a model involving self-assembly of protein aggregates at the air-water interface in which initial foam formation is facilitated by specific surfactant proteins in the mixture, further stabilized by subsequent aggregation and cross-linking into a multilayer surface complex.