The effects of cultivation depth,areal density,and nutrient level on lipid accumulation of <Emphasis Type="Italic">Scenedesmus acutus</Emphasis> in outdoor raceway ponds

Lipid accumulation is critical in the production of biodiesel from microalgae. However, little work has been done on the assessment of lipid accumulation during nitrogen stress in large research-scale outdoor raceways during different seasons; most values for lipid accumulation are assumptions based on work completed in laboratory settings or outdoor photobioreactors. This study focused on the use of raceway ponds operated in batch cultivation mode with an area of 30.37 m² to determine the impacts of nitrate-nitrogen concentration and cultivation depth on the ability of Scenedesmus acutus strain LB 0414 to accumulate lipids. A concentration of less than 60 mg N-NO₃ ^??L^?1 was required for removal of nitrogen in the cultivation medium within 8 days to stimulate lipid accumulation and increase lipid productivity. When nitrate concentrations were increased to prevent nitrogen depletion, lipid productivity decreased, which demonstrates that stressing is needed to induce lipid accumulation for increased lipid productivity. Additionally, decreasing cultivation depth below 9 cm, compared to raceways operated at a depth of 20–24 cm, increased lipid productivity by 62 % in December 2014 and 38 % in February 2015. More desirable environmental conditions, mainly increased sunlight and temperature, in February, increased biodiesel productivity for all raceways and account for the decrease in productivity differences. This research highlights increased lipid productivity found by reducing cultivation depth and nitrogen concentrations in outdoor raceways and provides insight into the optimal conditions for large-scale biodiesel production.     

Ulva lactuca and U. flexuosa (Chlorophyta,Ulvophyceae) cultivation in Brazilian tropical waters: recruitment,growth, and ulvan yield

Ulva spp. are used in a wide range of commercial applications, including bioremediation, food, bioenergy, pharmaceuticals, and agriculture. The sulfated polysaccharide ulvan obtained from Ulva spp. is of interest for triggering plant defenses against disease. However, the cultivation of Ulva spp. is still in its infancy. This study verified the feasibility of cultivating Ulva lactuca and Ulva flexuosa at two sites on the tropical Brazilian coast. We investigated the following: (a) methods to induce sporulation, (b) comparison of seeding ropes inoculated in vitro versus seeding at sea over 40 days, (c) production and harvest cycles at 15 and 30 days, (d) growth productivity of U. flexuosa at sea and in outdoor tanks, and (e) comparison of ulvan yields from biomass cultivated in tanks and the sea. High nutrient treatment was the most efficient method to induce sporulation (7,540?±?3,133 spores m^?1). Sea-based cultivation of U. flexuosa was only successful at one site. Seeding of ropes in vitro was more efficient than seeding at sea (0.31?±?0.20 g m^?2 day^?1), and 15-day harvest cycles were most efficient (20.1?±?1.8 % day^?1; 0.46?±?0.11 g m^?2 day^?1). Despite differences in plant growth in tanks (27.9?±?4.4 % day^?1) and at sea (20.1?±?1.8 % day^?1), the dry biomass and ulvan yields (17.7?±?5.0 %) did not differ between these systems. Cultivation of U. flexuosa was feasible at sea using in vitro seeding with a production cycle of 15 days in Brazilian tropical waters and tanks with high irradiance and enriched seawater.     

Biomass and terpenoids produced by mutant strains of <Emphasis Type="Italic">Arthrospira</Emphasis> under low temperature and light conditions

The filamentous Cyanobacterium Arthrospira is commercially produced and is a functional, high-value, health food. We identified 5 low temperature and low light intensity tolerant strains of Arthrospira sp. (GMPA1, GMPA7, GMPB1, GMPC1, and GMPC3) using ethyl methanesulfonate mutagenesis and low temperature screening. The 5 Arthrospira strains grew rapidly below 14?°C, 43.75 μmol photons m^?2 s^?1 and performed breed conservation at 2.5?°C, 8.75 μmol photons m^?2 s^?1. We used morphological identification and molecular genetic analysis to identify GMPA1, GMPA7, GMPB1 and GMPC1 as Arthrospira platensis, while GMPC3 was identified as Arthrospira maxima. Growth at different culture temperatures was determined at regular intervals using dry biomass. At 16?°C and 43.75 μmol photons m^?2 s^?1, the maximum dry biomass production and the mean dry biomass productivity of GMPA1, GMPB1, and GMPC1 were 2057?±?80 mg l^?1, 68.7?±?2.5 mg l^?1 day^?1, 1839?±?44 mg l^?1, 60.6?±?1.8 mg l^?1 day^?1, and 2113?±?64 mg l^?1, 77.7?±?2.5 mg l^?1 day^?1 respectively. GMPB1 was chosen for additional low temperature tolerance studies and growth temperature preference. In winter, GMPB1 grew well at mean temperatures <10?°C, achieving 3258 mg dry biomass from a starting 68 mg. In summer, GMPB1 grew rapidly at mean temperatures more than 28?°C, achieving 1140 mg l^?1 dry biomass from a starting 240 mg. Phytonutrient analysis of GMPB1 showed high levels of C-phycocyanin and carotenoids. Arthrospira metabolism relates to terpenoids, and the methyl-d-erythritol 4-phosphate pathway is the only terpenoid biosynthetic pathway in Cyanobacteria. The 1-deoxy-d-xylulose 5-phosphate reductoisomerase (DXR) gene from GMPB1 was cloned and phylogenetic analysis showed that GMPB1 is closest to the Cyanobacterium Oscillatoria nigro-viridis PCC711. Low temperature tolerant Arthrospira strains could broaden the areas suitable for cultivation, extend the seasonal cultivation time, and lower production costs.     

Improvement of biomass and fatty acid productivity in ocean cultivation of <Emphasis Type="Italic">Tetraselmis</Emphasis> sp. using hypersaline medium

In this study, hypersaline media were used for ocean cultivation of the marine microalga Tetraselmis sp. KCTC12432BP for enhanced biomass and fatty acid (FA) productivity. Hypersaline media (55, 80, and 105 PSU) were prepared without sterilization by addition of NaCl to seawater obtained from Incheon, Korea. The highest biomass productivity was obtained at 55 PSU (0.16 g L^?1 day^?1) followed by 80 PSU (0.15 g L^?1 day^?1). Although the specific growth rate of Tetraselmis decreased at salinities higher than 55 PSU, prevention of contamination led to higher biomass productivity at 80 PSU than at 30 PSU (0.03 g L^?1 day^?1). FA content of algal biomass increased as salinity increased to 80 PSU, above which it declined, and FA productivity was highest at 80 PSU. Ocean cultivation of Tetraselmis was performed using 50-L tubular module photobioreactors and 2.5-kL square basic ponds, closed- and open-type ocean culture systems, respectively. Culturing microalgae in hypersaline medium (80 PSU) improved biomass productivities by 89 and 152% in closed and open cultures, respectively, compared with cultures with regular salinity. FA productivity was greatly improved by 369% in the closed cultures. The efficacy of salinity shift and N-deficiency to enhance FA productivity was also investigated. Lowering salinity to 30 PSU with N-starvation following cultivation at 80 PSU improved FA productivity by 19% in comparison with single-stage culture without N-deficiency at 30 PSU. The results show that salinity manipulation could be an effective strategy to improve biomass and FA productivity in ocean cultivation of Tetraselmis sp.     

The potential of microalgal biomass production for biotechnological purposes using wastewater resources

The utilization of microalgae for wastewater treatment represents an attractive opportunity for wastewater valorization through the use of the produced biomass. Five strains of microalgae were isolated from municipal wastewater and grown in autoclaved and non-autoclaved effluent at 30 °C and 150 μmol photons m^?2 s^?1 to study biomass production, nutrient removal, and the biochemical composition of the biomass. All strains reached high biomass productivity (35.6 to 54.2 mg dry weight L^?1 day^?1) within 4 days of batch culturing. In this period, ammonium-N and phosphate were reduced by more than 60 and 90 %, respectively. The high growth rate (0.57 to 1.06 day^?1) ensured a rapid removal of nutrients and thereby a short retention time. By the fourth day of cultivation, the algal biomass contained 32 % protein, but only 11 % lipids and 18 % carbohydrates. It was found that the biomass was a suitable raw material for biogas production by anaerobic digestion. Biodigestion of obtained biomass was simulated by employing the Aspen HYSYS modeling software, resulting in methane yields comparable to those found in the literature. The elemental analysis of the algal biomass showed very low concentrations of pollutants, demonstrating the potential of use of the digestate from biodigestion as a bio-fertilizer.     

Cultivation of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> with swine wastewater and potential for algal biodiesel production

In this study, an alga-based simultaneous process of treating swine wastewater (SWW) and producing biodiesel was explored. Chlorella vulgaris (UTEX-265) was employed as a model species, and a SWW-based medium was prepared by dilution with tap water. Chlorella vulgaris grew well in the SWW-based medium, and at optimum dilution ratios, it exceeded the conventional culture medium in terms of biomass concentration and productivity. In eightfold diluted SWW, which supported the maximum growth, biomass productivity was 0.247 g L^?1 day^?1, while the productivity was merely 0.165 g L^?1 day^?1 in standard tris-acetate-phosphorous (TAP) algal medium. In addition, fatty acid methyl ester (FAME) productivity was greater in the SWW-based medium (0.067 versus 0.058 g L^?1 day^?1). This enhanced productivity resulted in more than 95 % removal of both nitrogen and phosphorous. All these show that C. vulgaris cultivation is indeed possible in a nutrient-rich wastewater with appropriate dilution, and in so doing, the wastewater can effectively be treated.     

Key parameters for outdoor biomass production of Scenedesmus obliquus in solar tracked photobioreactors

The biomass productivity of Scenedesmus obliquus was investigated outdoors during all seasons in solar tracked flat panel photobioreactors (PBR) to evaluate key parameters for process optimization. CO₂ was supplied by flue gas from an attached combined block heat and power plant. Waste heat from the power plant was used to heat the culture during winter. The parameters pH, CO₂, and inorganic salt concentrations were automatically adjusted to nonlimiting levels. The optimum biomass concentration increased directly with the photosynthetic active radiation (PAR) from 3 to 5 g dry weight (DW)?L^?1 for a low PAR of 10 mol photons m^?2 day^?1 and high PAR of 40–60 mol photons m^?2 day^?1, respectively. The annual average biomass yield (photosynthetic efficiency) was 0.4?±?0.5 g DW mol^?1 photons. However, biomass yields of 1.5 g DW mol^?1 photons close to the theoretical maximum were obtained at low PAR. The productivity (including the night biomass losses) ranged during all seasons from ?5 up to 30 g DW m^?2 day^?1 with a mean productivity of 9?±?7 g DW m^?2 day^?1. Low night temperatures of the culture medium and elevated day temperatures to the species-specific optimum increased the productivity. Thus, continuous regulation of the biomass concentration and the culture temperature with regard to the fluctuating weather conditions is essential for process optimization of outdoor microalgal production systems in temperate climates.     

Inorganic carbon and pH effect on growth and lipid productivity of Tetraselmis suecica and Chlorella sp (Chlorophyta) grown outdoors in bag photobioreactors

There has been considerable interest in cultivation of green microalgae (Chlorophyta) as a source of lipid that can alternatively be converted to biodiesel. However, almost all mass cultures of algae are carbon-limited. Therefore, to reach a high biomass and oil productivities, the ideal selected microalgae will most likely need a source of inorganic carbon. Here, growth and lipid productivities of Tetraselmis suecica CS-187 and Chlorella sp were tested under various ranges of pH and different sources of inorganic carbon (untreated flue gas from coal-fired power plant, pure industrial CO₂, pH-adjusted using HCl and sodium bicarbonate). Biomass and lipid productivities were highest at pH 7.5 (320?±?29.9 mg biomass L^?1 day^?1and 92?±?13.1 mg lipid L^?1 day^?1) and pH 7 (407?±?5.5 mg biomass L^?1 day^?1 and 99?±?17.2 mg lipid L^?1 day^?1) for T. suecica CS-187 and Chlorella sp, respectively. In general, biomass and lipid productivities were pH 7.5?>?pH 7?>?pH 8?>?pH 6.5 and pH 7?>?pH 7.5?=?pH 8?>?pH 6.5?>?pH 6?>?pH 5.5 for T. suecica CS-187 and Chlorella sp, respectively. The effect of various inorganic carbon on growth and productivities of T. suecica (regulated at pH?=?7.5) and Chlorella sp (regulated at pH?=?7) grown in bag photobioreactors was also examined outdoor at the International Power Hazelwood, Gippsland, Victoria, Australia. The highest biomass and lipid productivities of T. suecica (51.45?±?2.67 mg biomass L^?1 day^?1 and 14.8?±?2.46 mg lipid L^?1 day^?1) and Chlorella sp (60.00?±?2.4 mg biomass L^?1 day^?1 and 13.70?±?1.35 mg lipid L^?1 day^?1) were achieved when grown using CO₂ as inorganic carbon source. No significant differences were found between CO₂ and flue gas biomass and lipid productivities. While grown using CO₂ and flue gas, biomass productivities were 10, 13 and 18 %, and 7, 14 and 19 % higher than NaHCO₃, HCl and unregulated pH for T. suecica and Chlorella sp, respectively. Addition of inorganic carbon increased specific growth rate and lipid content but reduced biomass yield and cell weight of T. suecica. Addition of inorganic carbon increased yield but did not change specific growth rate, cell weight or content of the cell weight of Chlorella sp. Both strains showed significantly higher maximum quantum yield (F_v/F_m) when grown under optimum pH.     

Lipid productivity and fatty acid composition in Chlorella and Scenepdesmus strains grown in nitrogen-stressed conditions

Thirty Chlorella and 30 Scenedesmus strains grown in nitrogen-stressed conditions (70 mg L^?1 N) were analyzed for biomass accumulation, lipid productivity, protein, and fatty acid (FA) composition. Scenedesmus strains produced more biomass (4.02?±?0.73 g L^?1) after 14 days in culture compared to Chlorella strains (2.57?±?0.12 g L^?1). Protein content decreased and lipid content increased from days 8 to 14 with an increase in triacylglycerol (TAG) accumulation in most strains. By day 14, Scenedesmus strains generally had higher lipid productivity (53.5?±?3.7 mg lipid L^?1 day^?1) than Chlorella strains (35.1?±?2.8 mg lipid L^?1 day^?1) with the lipids consisting mainly of C16–18 TAGs. Scenedesmus strains generally had a more suitable FA profile with higher amounts of saturated fatty acids and monounsaturated fatty acids (MUFAs) and a smaller polyunsaturated fatty acid (PUFA) component. Chlorella strains had a larger PUFA component and smaller MUFA component. The general trend in the FA composition of Chlorella strains was oleic > palmitic > α-linolenic = linoleic > eicosenoic > heptadecenoic > stearic acid. For Scenedesmus strains, the general trend was oleic > palmitic > linoleic > α-linolenic > stearic > eicosenoic > palmitoleic > heptadecenoic acid. The most promising strains with the highest lipid productivity and most suitable FA profiles were Scenedesmus sp. MACC 401, Scenedesmus soli MACC 721, and Scenedesmus ecornis MACC 714. Although Chlorella sp. MACC 519 had lower lipid productivity, the FA profile was good with a lower PUFA component compared to the other Chlorella strains analyzed and a low linolenic acid concentration.     

Productivity and biochemical composition of <Emphasis Type="Italic">Tetradesmus obliquus</Emphasis> and <Emphasis Type="Italic">Phaeodactylum tricornutum</Emphasis>: effects of different cultivation approaches

The present work evaluated biomass productivity, carbon dioxide fixation rate, and biochemical composition of two microalgal species, Phaeodactylum tricornutum (Bacillariophyta) and Tetradesmus obliquus (Chlorophyta), cultivated indoors in high-technology photobioreactors (HT-PBR) and outdoors both in pilot ponds and low-technology photobioreactors in a greenhouse in southern Italy. Microalgae were grown in standard media, under nitrogen starvation, and in two liquid digestates obtained from anaerobic digestion of agro-zootechnical and vegetable biomass. P. tricornutum, cultivated in semi-continuous mode in indoor HT-PBRs with standard medium, showed a biomass productivity of 21.0?±?2.3 g m^?2 d^?1. Applying nitrogen starvation, the lipid productivity increased from 2.3 up to 4.5?±?0.5 g m^?2 d^?1, with a 24 % decrease of biomass productivity. For T. obliquus, a biomass productivity of 9.1?±?0.9 g m^?2 d^?1 in indoor HT-PBR was obtained using standard medium. Applying liquid digestates as fertilizers in open ponds, T. obliquus gave a biomass productivity (10.8?±?2.0 g m^?2 d^?1) not statistically different from complete medium such as P. tricornutum (6.5?±?2.2 g m^?2 d^?1). The biochemical data showed that the fatty acid composition of the microalgal biomass was affected by the different cultivation conditions for both microalgae. In conclusion, it was found that the microalgal productivity in standard medium was about doubled in HT-PBR compared to open ponds for P. tricornutum and was about 20 % higher for T. obliquus.     

<Emphasis Type="Italic">Tetraselmis suecica</Emphasis> culture for CO<Subscript>2</Subscript> bioremediation of untreated flue gas from a coal-fired power station

The accumulation of atmospheric CO₂, primarily due to combustion of fossil fuels, has been implicated in potential global climate change. The high rate of CO₂ bioremediation by microalgae has emerged as a favourable method for reducing coal-fired power plant emissions. However, coal-fired power station flue gas contains other chemicals such as SO_x which can inhibit microalgal growth. In the current study, the effect of untreated flue gas as a source of inorganic carbon on the growth of Tetraselmis in a 1000 L industrial-scale split-cylinder internal-loop airlift photobioreactor was examined. The culture medium was recycled after each harvest. Tetraselmis suecica grew very well in this airlift photobioreactor during the 7-month experiment using recycled medium from an electroflocculation harvesting unit. Increased medium SO₄ ^2? concentration as high as 870 mg SO₄ ^2??L^?1 due to flue gas addition and media recycling had no negative effect on the overall growth and productivity of this alga. The potential organic biomass productivity and carbon sequestration using an industrial-scale airlift PBR at International Power Hazelwood, Gippsland, Victoria, Australia, are 178.9?±?30 mg L^?1 day^?1 and 89.15?±?20 mg?‘C’?L^?1 day^?1, respectively. This study clearly indicates the potential of growing Tetraselmis on untreated flue gas and using recycled medium for the purpose of biofuel and CO₂ bioremediation.     

Biological CO<Subscript>2</Subscript> fixation using C<Emphasis Type="Italic">hlorella vulgaris</Emphasis> and its thermal characteristics through thermogravimetric analysis

The present research is focused on cultivation of microalgae strain Chlorella vulgaris for bio-fixation of CO₂ coupled with biomass production. In this regard, a single semi-batch vertical tubular photobioreactor and four similar photobioreactors in series have been employed. The concentration of CO₂ in the feed stream was varied from 2 to 12 % (v/v) by adjusting CO₂ to air ratio. The amount of CO₂ capture and algae growth were monitored by measuring decrease of CO₂ concentration in the gas phase, microalgal cell density, and algal biomass production rate. The results show that 4 % CO₂ gives maximum amount of biomass (0.9 g L^?1) and productivity (0.118 g L^?1 day^?1) of C. vulgaris in a single reactor. In series reactors, average productivity per reactor found to be 0.078 g L^?1 day^?1. The maximum CO₂ uptake for single reactor also found with 4 % CO_2, and it is around 0.2 g L^?1 day^?1. In series reactors, average CO₂ uptake is 0.13 g L^?1 day^?1 per reactor. TOC analysis shows that the carbon content of the produced biomass is around 40.67 % of total weight. The thermochemical characteristics of the cultivated C. vulgaris samples were analyzed in the presence of air. All samples burn above 200 °C and the combustion rate become faster at around 600 °C. Almost 98 wt% of the produced biomass is combustible in this range.     

Improved Biomass and Hydrocarbon Productivity of Botryococcus braunii by Periodic Ultrasound Stimulation

Ultrasonic treatment was firstly found to accelerate both biomass and hydrocarbon productivities of Botryococcus braunii algal cells cultured in the shake flasks. The most effective sonication strategy was to subject the cells to three 5-min ultrasonic treatments at a 4-day interval using a fixed frequency of 40 kHz and power of 240 W, and the ultrasound-treated algal cells showed the highest biomass productivity of 0.043 g L^?1 day^?1 and the highest hydrocarbon productivity of 13.1 mg L^?1 day^?1 among all ultrasound treatments tested. The improved productivity was proved to be mainly due to the enhancement of both endogenous indole-3-acetic acid (IAA) biosynthesis and membrane permeability in the ultrasound-stimulated algal cells. The efficient ultrasonic stimulation strategy also showed good performance for the algal culture in a 2-L airlift bioreactor. Together, these results not only illustrate the immense potential for an enhanced understanding on ultrasound-stimulated algal cells but also as provide a powerful process intensification method to improve the biomass and hydrocarbon productivity of B. braunii in practice.     

Attached culture of Nannochloropsis oculata for lipid production

The influences of urea, nitrate and glycine with four concentration levels on attached culture of Nannochloropsis oculata were investigated. The organic nitrogen source glycine was effective on improving not only adhesion biomass productivity but also adhesion rate. The maximum adhesion biomass productivity of 15.76 ± 0.52 g m^?2 day^?1 with adhesion rate of 76.67 ± 0.42 % was achieved with 18 mM glycine. To increase the lipid production, three lipid enhancing strategies were conducted afterwards, including nitrogen starvation, high light, and the combination of nitrogen starvation and high light. In nitrogen starvation situation, although the lipid content was greatly increased, the adhesion biomass productivity dropped probably due to the low cell viability. Increasing light intensity was effective on enhancing both adhesion biomass productivity and lipid content. The results indicated that nitrogen starvation was effective on improving both lipid content and adhesion rate when high light was applied. The maximum lipid yield of 4.32 ± 0.14 g m^?2 day^?1 with adhesion biomass productivity of 21.32 ± 0.65 g m^?2 day^?1, adhesion rate of 86.81 ± 0.10 % and lipid content of 20.24 ± 0.06 % was achieved with the combination strategy.     

Interspecific biodiversity enhances biomass and lipid productivity of microalgae as biofuel feedstock

Large improvements in biomass and lipid production are required to make massive scale algal biodiesel production an economic reality. The application of the biodiversity strategy to enhance algal biomass as biofuel feedstock is little. The algal diversity was manipulated in this study to investigate the effects of a combination of biodiversity complementarity and a new medium consisting of seawater and agricultural fertilizer on lipid productivity. The algae diverse community includes two strains of Dunaliella salina (Dunaliella salina 19/30 and 19/18) and three species of Nannochloropsis (Nannochloropsis oculata, Nannochloropsis salina, and Nannochloropsis gaditana). The results showed that the most diverse community (5 species) produced an average of sixfold more biomass in the new medium than did the standard f/2 culture medium. The most diverse polyculture had the highest growth rate (1.01 day^?1), biomass (1.2 g L^?1), and lipid productivity (0.31 g L^?1 day^?1). The assessment of algal polycultures relative to monocultures is particularly interesting and novel for this biofuel field, and the observations that these polycultures resulted in significant lipid productivity improvements are very useful addition to the biofuel research. The possible mechanism (resource diversity) to explain the synergy in mixed cultures warrants further investigation.     

Evaluation of indigenous microalgal isolate Chlorella sp. FC2 IITG as a cell factory for biodiesel production and scale up in outdoor conditions

The present study reports evaluation of an indigenous microalgal isolate Chlorella sp. FC2 IITG as a potential candidate for biodiesel production. Characterization of the strain was performed under photoautotrophic, heterotrophic, and mixotrophic cultivation conditions. Further, an open-pond cultivation of the strain under outdoor conditions was demonstrated to evaluate growth performance and lipid productivity under fluctuating environmental parameters and in the presence of potential contaminants. The key findings were: (1) the difference in cultivation conditions resulted in significant variation in the biomass productivity (73–114 mg l^?1 day^?1) and total lipid productivity (35.02–50.42 mg l^?1 day^?1) of the strain; (2) nitrate and phosphate starvation were found to be the triggers for lipid accumulation in the cell mass; (3) open-pond cultivation of the strain under outdoor conditions resulted in biomass productivity of 44 mg l^?1 day^?1 and total lipid productivity of 10.7 mg l^?1 day^?1; (4) a maximum detectable bacterial contamination of 7 % of the total number of cells was recorded in an open-pond system; and (5) fatty acid profiling revealed abundance of palmitic acid (C16:0), oleic acid (C18:1) and linoleic acid (C18:2), which are considered to be the key elements for suitable quality biodiesel.     

Biomass and Lipid Production of Dinoflagellates and Raphidophytes in Indoor and Outdoor Photobioreactors

The principal fatty acids from the lipid profiles of two autochthonous dinoflagellates (Alexandrium minutum and Karlodinium veneficum) and one raphidophyte (Heterosigma akashiwo) maintained in bubble column photobioreactors under outdoor culture conditions are described for the first time. The biomass production, lipid content and lipid productivity of these three species were determined and the results compared to those obtained when the strains were cultured indoors. Under the latter condition, the biotic values did not significantly differ among species, whereas under outdoor conditions, differences in both duplication time and fatty acids content were observed. Specifically, A. minutum had higher biomass productivity (0.35 g·L^?1 day^?1), lipid productivity (80.7 mg lipid·L^?1 day^?1) and lipid concentration (252 mg lipid·L^?1) at harvest time (stationary phase) in outdoor conditions. In all three strains, the growth rate and physiological response to the light and temperature fluctuations of outdoor conditions greatly impacted the production parameters. Nonetheless, the species could be successfully grown in an outdoor photobioreactor and were of sufficient robustness to enable the establishment of long-term cultures yielding consistent biomass and lipid production.     

Assessment of key biological and engineering design parameters for production of Chlorella zofingiensis (Chlorophyceae) in outdoor photobioreactors

For the design of a large field of vertical flat plate photobioreactors (PBRs), the effect of four design parameters—initial biomass concentration, optical path length, spacing, and orientation of PBRs—on the biochemical composition and productivity of Chlorella zofingiensis was investigated. A two-stage batch process was assumed in which inoculum is generated under nitrogen-sufficient conditions, followed by accumulation of lipids and carbohydrates in nitrogen-deplete conditions. For nitrogen-deplete conditions, productivity was the most sensitive to initial biomass concentration, as it affects the light availability to individual cells in the culture. An initial areal cell concentration of 50 g m^?2 inoculated into 3.8-cm optical path PBR resulted in the maximum production of lipids (2.42?±?0.02 g m^?2 day^?1) and carbohydrates (3.23?±?0.21 g m^?2 day^?1). Productivity was less sensitive to optical path length. Optical path lengths of 4.8 and 8.4 cm resulted in similar areal productivities (biomass, carbohydrate, and lipid) that were 20 % higher than a 2.4-cm optical path length. Under nitrogen-sufficient conditions, biomass productivity was 48 % higher in PBRs facing north–south during the winter compared to east–west, but orientation had little influence on biomass productivity during the spring and summer despite large differences in insolation. An optimal spacing could not be determined based on growth alone because a tradeoff was observed in which volumetric and PBR productivity increased as space between PBRs increased, but land productivity decreased.     

Postharvest growth dynamic of <Emphasis Type="Italic">Schoenoplectus californicus</Emphasis> along fluvio-estuarine and flooding gradients

The emergent wetland plant Schoenoplectus californicus is used as fiber in several American countries, but the effects of harvesting on this species have not previously been studied. We analyzed the biomass production, stem density and morphometry of this species along fluvio-estuarine and flooding gradients and evaluated the effects of harvesting on growth and recovery capacity in the Santa Lucía River (Uruguay), comparing river sections and surface elevations. Differences in biomass, length and stem density were associated with the dynamics of the hydrological regime. The mean biomass and length growth rates were 3.0 ± 2.8 g day^?1 and 0.8 ± 0.5 cm day^?1, respectively. The analysis of the postharvest growth dynamic showed variation among the stems, suggesting the existence of mechanisms of plant compensation for the harvest effect. Six months after the harvest, S. californicus had recovered, e.g., in stem length and density, while the biomass showed a slower recovery. Our results suggest that the recovery capacity of this species depends on the population structure before the harvest and on favorable conditions during the recovery period. Based on our results, we recommend strategies for sustainable harvest management.     

Performance of bioelectrochemical systems inoculated with Desmodesmus sp. A8 under different light sources

Light source can affect the stomata opening, photosynthesis process, and pigment content in microalgae cells. In this study, growth rate, chlorophyll a (chl a) content, and electrogenic capability of Desmodesmus sp. A8 were investigated under incandescent and fluorescent lamps. Growth rate, productivity, and chl a content of strain A8 exposed to incandescent light were recorded as 0.092 ± 0.010 day^?1, 0.019 ± 0.008 g L^?1 day^?1, and 15.10 ± 1.40 mg L^?1, which decreased to 0.086 ± 0.006 day^?1, 0.012 ± 0.004 g L^?1 day^?1, and 10.06 ± 1.59 mg L^?1, respectively, under fluorescent light. The stable current density of bioelectrochemical systems inculcated with strain A8 under incandescent and fluorescent lamps were 249.76 and 158.41 mA m^?2 at ?0.4 V vs. Ag/AgCl, coupling with dissolved oxygen within biofilm decreasing from 15.91 to 10.80 mg L^?1. This work demonstrated that illuminating microalgae under an incandescent lamp can improve biomass production and electrogenic capabilities.